Page 1
READ
Installation and Startup Guide
MPP Modular Pressure
THIS
Transmitter
FIRST
Version 2.1
PRODUCT DESCRIPTION
The model MPP modular pressure transmitter has been specically designed for
placement in sanitary process applications in the Life Sciences industry where
Anderson Instrument Co., Inc.
156 Auriesville Rd., Fultonville, NY 12072
Phone: 518-922-5315
Fax: 518-922-8997
www.anderson-negele.com
accurate and repeatable pressure measurements in difcult (vibration, wide
temperature swings, humidity) environments are required. The modular design
allows for eld conguration to best suit application needs and allows economical
component replacement. State of the art performance yields class leading
accuracy and stability while minimizing process and ambient temperature effects. A
menu driven interface with an internal diagnostic display provides user adjustability
of pressure range and a host of other control characteristics without tools or
pressure standards.
SENSOR WIRING
To facilitate electrical connections the MPP transmitter will be provided with either a 5 pin M12 quick disconnect
receptacle, a M16 thread cable gland, or a ½” NPTF threaded adaptor. Shielded cable is recommended. See manual for
additional detail.
Field wireable connectors or molded cordsets are available as accessories from Anderson Instrument.
Document 1184
FIELD WIREABLE CONNECTOR ASSEMBLY - ORDERED AS ACCESSORY
1. Insert cable through Pressing Screw, Compression
Ring, Seal Grommet, and Sleeve as shown below.
2. Strip back 1-1/4” of outer sheathing, cut off any excess
wires, shield and ground. Strip off 1/4” insulation from
remaining two wires. It is not necessary or recommended
Shown with
wire cover plate
removed
Swtiches and display only on
EX
MENU
_
UP
DOWN
HART version
LOOP
+
SENSOR
3. Orient Connector end so that
center pin connecting screw is
horizontal facing right (see
detail).
Retaining Ring
Connector End
Pin 2 - Black
(Loop -)
DETAIL
Sleeve
Center screw pin
orientation reference
Pin 1 - Red
(Loop +)
MOLDED CORD SETS
Anderson Cord Set
Loop+(red) wire Pin 1
Loop- (black) wire Pin 2
Shield (clear or bare) wire
Note: Green and White not used
Typical Cord Set by others
4. Wire LOOP+ (red) wire to top-right
terminal, and LOOP- (black) wire to
top-left terminal. No connection is
made to the center and bottom
terminals.
5. Screw on the Sleeve. Hand-tighten only.
Compression
Ring
Seal
-2 included choose one to accommodate cable OD
Grommet
6. Press the Seal Grommet into the Sleeve and
hand-tighten the Pressing Screw against the
compression ring.
7. Use a wrench to tighten the Pressing Screw
another 3/4 turn. Do not over-tighten!
Pressing Screw
Loop+(brown) wire Pin 1
Loop- (white) wire Pin 2
Shield (bare) wire
Page 2
USER INTERFACE GUIDE
The Anderson MPP Modular Pressure Transmitter is factory calibrated to the URL (upper range limit) and congured to the range
and units specied by the order matrix number. Range, pressure units, output damping and analog scale (HART only) may be easily
modied by the user. The Display Interface (DI) provides user feed back for menu functions, displays diagnostic error codes and
nominally loop current or process variable.
The Modular Pressure Transmitter conguration parameters are sorted into three modes, and are accessible via the button along the
bottom of the display interface. While the cover is removed, do not allow moisture to enter the housing.
RUN Mode
Zero
Adjust Display Decimal
Momentarily Display mA Output (HART only)
Descriptive Error Message
0%
Down
Execute
Display Interface
50%
PHARMACEUTICAL
SERIES
E
M
100%
Up
Menu
SENSOR CONFIG Mode
PSIG/BAR (native units)
4-20mA / 20-4mA (HART only)
LRV
URV
Damping
Alarm1
Alarm2
Display Units
Unit Description Scroll
Factory Restore
CALIBRATION Mode
2 Point Cal
4 Point Cal
SENSOR CONFIGURATION
Each instruction assumes starting from RUN mode which is default at power on and process value is displayed.
CALIBRATION – Zero
NOTE – For ABSOLUTE stems zero calibration is disabled as zeroing is not possible in atmospheric conditions.
Zeroing the sensor provides the best accuracy when clamped into the application therefore negates possible positioning and clamping
errors. Be sure sensor is exposed to zero psig when performing this function.
1. Press both “D” and “M” simultaneously for approximately 5 seconds – Sensor displays 4.00 milliamp (HART version), or
0.00 (FFB version) for gauge, for compound sensor displays appropriate output for set range
Native Units: PSI or Bar
1. Press “M” – Sensor displays “COnF”
2. Press “E” – Sensor displays “PSI” or “BAR”
3. Press “U” or “D” – Sensor toggles between “PSI” or “BAR”
4. Press “M” to proceed to the next operation
Note: When changing units conguring range is now required
Page 3
Output: 4Ma – 20Ma or 20mA – 4mA (HART only)
1. Press “M” – Sensor displays “COnF”
2. Press “E” – Sensor displays “PSI” or “BAR”
3. Press “M” – Sensor displays “4-20” or “20-4”
4. Press “U” or “D” – Sensor toggles between “4-20” or “20-4”
5. If no other operation is to be accessed exit to “RUN” mode via pressing “M” repeatedly until process value is displayed
PRESSURE RANGE
LRV: Lower range value
Sensors equipped with ”Compound” style measurement cells (stem) may congure the LRV. “Absolute” stems are predened as 0
and are not recongurable
1. Press “M” – Sensor displays “COnF”
2. Press “E” – Sensor displays “PSI” or “BAR”
3. Press “M” – Sensor displays “4-20” or “20-4” (HART only)
4. Press “M” – Sensor displays “LRV”
5. Press “E” – Sensor displays present LRV value – Example: “0”
6. Press “U” or “D” to set desired LRV value– Sensor display increases or decreases accordingly
Note: continue to URV
URV: Upper range value
Note: starting from LRV above
7. Press “M” – Sensor displays “URV”
8. Press “E” – Sensor displays present URV value – Example: “50”
9. Press ”U” or “D” to set desired URV value – Sensor display increases or decreases accordingly
10. Press “E” to store displayed value – Sensor displays “URV”
11. If no other operation is to be accessed exit to “RUN” mode via pressing “M” repeatedly until process value is displayed
Output Damping
1. Press “M” – Sensor displays “COnF”
2. Press “E” – Sensor displays “PSI” or “BAR”
3. Press “M” – Sensor displays “4-20” or “20-4” (HART only)
4. Press “M” – Sensor displays “LRV”
5. Press “M” – Sensor displays “URV”
6. Press “M” – Sensor displays “dMPg”
7. Press “E” – Sensor displays current damping value from 0 - 10
8. Press “U” or “D” to display desired damping value– Sensor display increases or decreases accordingly
9. Press “E” to store displayed value – Sensor displays “dMPg”
10. If no other operation is to be accessed exit to “RUN” mode via pressing “M” repeatedly until process value is displayed
Setting Display Process Variable - Functionality in display interface only.
For additional display interface functionalities see section 7.2 of the manual.
The following Engineering units may be selected:
Millibar, Torr & Kg/cm2, PSI, BAR, kPA, In H2O, In Hg, mm H2O, mA
1. Press “M” – Sensor displays “CONF”
2. Press “E” – Sensor displays “PSIG” or “BARG”
3. Press “M” – Sensor displays “4-20” or “20-4”(HART only)
4. Press “M” – Sensor displays “LRV”
5. Press “M” – Sensor displays “URV”
6. Press “M” – Sensor displays “DAMP”
7. Press “M” – Sensor displays “ALRM1”
8. Press “M” – Sensor displays “ALRM2”
9. Press “M” – Sensor displays currently set engineering unit
10. Press “U” or “D” repeatedly to select the desired engineering unit
11. Press “M” to proceed to next operation or repeatedly to exit to “run” mode
Factory configuration reset
Perform if a return to the original factory conguration is desired
1. Press “M” – Sensor displays “COnF”
2. Press “E” – Sensor displays “PSI” or “BAR”
3. Press “M” – Sensor displays “4-20” or “20-4” (HART only)
4. Press “M” – Sensor displays “LRV”
5. Press “M” – Sensor displays “URV”
6. Press “M” – Sensor displays “dMPg”
7. Press “M” – Sensor display “FrES”
8. Press “E” – Sensor display “nO”
9. Press “U” or “D” to display “YES”
10. Press “E” – Sensor display “FrES”
11. exit to “RUN” mode via pressing “M” repeatedly until process value is displayed
Page 4
EXPLODED VIEW
3.55
6.59
3.55
6.59
Cap
Display Interface
Puck
DIMENSIONAL DRAWINGS
3.6"
(91mm)
Housing
M12 Quick
Disconnect
Stem
ACCESSORIES
Cord Sets
Shielded Molded w/25’ cable 42117K0025
Shielded Molded w/50’ cable 42117K0050
Shielded Molded w/100’ cable 42117K0100
Clear Cap w/gaskets 56328P0001
Stainless Steel Cap w/gaskets 56329P0001
Enclosure w/Clear cap w/gaskets SP5632700066
Enclosure w/SS cap w/gaskets SP56327A0066
M12 Quick Disconnect Receptacle SP56726A0002
Cord Grip SP5633100000
1/2” NPTF adaptor SP5633200000
Seal Kit (6) gaskets 5633000001
Field Wireable Connector-Straight 42119B0000
Field Wireable Connector-90° 42119A0000
Display Kit - HART option SP56741P0066
Display Kit - FFB option SP56741F0066
5’ Remote Kit SP73228A0005
10’ Remote Kit SP73228A0010
15’ Remote Kit SP73228A0015
20’ Remote Kit SP73228A0020
25’ Remote Kit SP73228A0025
3.6"
(91mm)
6.6" (167mm)
Horizontal Orientation
Cable available
in 5’, 10’, 15’, 20’
and 25’ lengths
6.6" (167mm)
Vertical Orientation
7.87” (200mm)
Loading...