Anchor NAVI-TRAC FRAME LIFT User Manual

NAVI-TRAC FRAME LIFT

ASSEMBLY INSTRUCTIONS

1100 Burch Drive.
Evansville, Indiana 47724

Phone: [phone]
Fax: [phone]
E-mail: www.anchorinc.com

A

14

6

5

2

9,10

8

9,10

1

See Image “A”

1. Attach the lower end (2-hole pattern) of the Bottom
Post (#5) to the rear most splice stub of the Base

Weldment (#1) (use Hdw #9 & 10). The single,
centered channel of the post should face forward.

2. Insert the Leg Inserts (#2) and pin with (#14).

3. The Turf Wheels (#21) have been pre-installed.

4. One at a time, remove the bolts (#9 & 10) holding the
splice at the top of the Bottom Post (#5) to install the
Hinges for Brace (#8) on each side of the bottom post.
Secure the hinges by replacing the same hardware
(9 & 10).

B

7

4

11

20,21

15

16,17

12,13

18

See Image “B”

5. Install the Brace Weldments (#4) to the Brace Hinges (#8) on both sides of the bottom post (use hdw #16 & 17) at the brace
hinge (#8)

6. Lean the Frame Lift over, as needed, to slide the Top Post (#7) onto the Splice of the bottom post and secure (use hdw #15).

7. To limit the spread of the Brace Weldments, install Eyes (#12 & 13) into the bottom post and attach the 36” web (#11) between the
brace (use hdw #20 & 21) and the bottom post (use snap #18).

See Images “C, D, & E”

8. While the Frame Lift is leaned over, attach the pre-assembled lifting web and winch assembly starting with the Winch Assembly
(#24) to the Bottom Post (use hdw #25 & 26). See images C and D.

C

Warning:

Always position winch assembly as shown in image “D”. Do not
attach upside down - winch brake system may fail.

Lifting Web

Handle

Winch Assembly

Spring
Shaft Extension
Washer

Bolt

For warnings, maintenance and
replacement parts, refer to the
Dutton-Lainson booklet that is
shipped with this winch (the B1500)

Winch Assembly

Bottom Post

Winch Assembly

properly mounted

D

9. Next, feed the web assembly to the top and insert the Web Top Weldment (#3) into the top of the Top Post (#7) and secure with
(hdw #9,10). The Eave Hook (#27) should hang at the front of the Lift with the cup forward and can be secured to the front splice
stub of the base plate when not in use. See Image “F” for storage of the Frame Lift when not in use.

10. Follow the instructions in the Navi-Trac Assembly Manual for proper positioning and use of the Navi-Trac Frame Lift for
assembling and standing the Navi-Trac frame.

EC4418

NTFL 0811

ITEM # QTY DESCRIPTION

11
22
31
42
51
61SPLICE TOP POST
71
82

93
10 3
11 2
12 1
13 1
14 2
15 3
16 2
17 2
18 2
19 4
20 4
21 2
22 2
23 2
24 1
25 2
26 2
27 1
28 25’-6”

PART LIST

BASE WELDMENT
LEG INSERT
WEB GUIDE TOP WELDMENT
BRACE WELDMENT
BOTTOM POST

TOP POST
HINGE FOR BRACE
1/2” x 3” HEX HD CAP SCREW
1/2” ST’D NC NYLOCK NUT
1” POLYPRO WEB
1/2” x 3 1/4” EYE BOLT
1/2” EYE NUT
1/2” x 3 1/4” FAS PIN
1/2” x 2 3/4” TENSION LOCK PIN
1/2”-13 x 3 1/4” HEX HD CAP SCREW
1/2”-13 NYLOCK JAM NUT
SNAP
#10 FENDER WASHER
1” x #10 TEC SCREW
3 1/2” x 10 1/2” DIA. TURF WHEEL
1/2”-13 x 5” HEX HD CAP SCREW
1/2”-13 HEX NUT
WINCH ASSEMBLY
3/8”-16 x 5 1/2” HEX HD CAP SCREW
3/8”-16 UNC HEX NUT
EAVE HOOK
1 1/2” POLYESTER WEB

E

28

27

3

7

24

25,26

F

The Top Post can be stored on
the front splice stub of the base
plate when not in use.

Thank you for purchasing an Anchor product. In return, we pledge quality, service and craftsmanship and are available for
any questions you may have or assistance you may need.

Phone Number

[phone]

Fax Number

[phone]

Anchor products are of superior design and operate best within the parameters of these instructions. It is imperative that
the instructions be carefully read and completely followed. Please read assembly instructions before the use of this prod­uct. Because this product may be used on a variety of Anchor tent products, you should also read the installation instruc­tions for the specific tent with which this tool is to be used. Tent installation instructions are available at: www.anchorinc.

com.

CAUTION:

1. Use for installation of framed tent products only. Read relevant tent installation instructions.
2, Never exceed the maximum operating load stated within these instructions. Excess load may cause premature failure

and could result in serious personal injury.

3. Do not oil or grease the brake mechanism of this frame lift.

4. Never apply load to winch with web fully extended. Keep at least three full turns of web on the reel at all times.

5. During use, be sure web is neither twisted nor wrapped around the pole.

6. Follow instructions carefully, paying particular attention to all safety or cautionary comments.
Proper safety equipment should be used at all times to insure a safe operation. We suggest a careful evaluation be made

to determine safety equipment needed, such as hard hats, steel-toe shoes, safety glasses and other as required.
Disclaimer - Anchor Industries disclaims and excludes all express or implied warranties of

merchantability and and fitness for a particular purpose. The product is sold “as is” and no warranty shall apply. The user
shall determine the suitability of the product for the intended use and assumes all risk and liability. Anchor Industries shall
not be liable in tort or in contract for any loss or damage, direct, incidental or consequential arising out of the use of or the
inability to use the product.

FL12-00