Analytical Industries Inc (AII) GPR-1500 DA Operating Manual

Technical Specifications *

Accuracy: < 2% of FS range under constant conditions
Analysis: 0-100, 0-1000 PPM, 0-1%, 0-25% (CAL) FS

Auto-ranging or manual lock on a single range

Application: Oxygen analysis in inert, hydrocarbon, helium, hydrogen,

mixed and acid (CO2) gas streams

Area Classification: General purpose
Alarms: Two user configurable alarms: magnetic coil relays rated

3A at 100 VAC, field programmable alarm time delays,
alarm bypass for calibration and system fail alarm

Calibration: Max interval—3 months. Use certified span gas with O2

content (balance N2) approximating 80% of full scale for
fast 20-30 minute recovery to online use. Alternatively,
air calibrate with clean source of compressed or ambient
(20.9% O2) air on 0-25% range and allow 60 minutes on
zero gas to recover to 10 ppm. For optimum accuracy,

calibrate one range higher than the range of interest.
Compensation: Barometric pressure and temperature
Connections: 1/8" compression tube fittings

Controls: Water resistant keypad; menu driven range selection,

calibration and system functions
Display: Graphical LCD 2.75” x 1.375”; resolution 0.01 PPM; dis-

plays real time ambient temperature and pressure
Enclosure: Fiberglass NEMA 4X, 6.75 x 8.375 x 4.25", 8 lbs.

Flow Sensitivity: Not flow sensitive, 1-2 SCFH recommended
Linearity: ±1% of full scale
Pressure: Inlet - regulate to 5-30 psig to deliver 1-2 SCFH flow;

vent - atmospheric
Power: 12-28 VDC non-loop or 110-220 VAC
Recovery Time: 30 seconds in air to < 100 PPM in < 15 mins on N2 purge

Response Time: 90% of final reading in 10 seconds
Sample System: None

Sensitivity: < 0.5% of FS range
Sensor Model: GPR-12-100-M for non-acid (CO2) gas streams;

XLT-12-100-M for gases containing > 0.5% CO2
Sensor Life: 24 months in < 1000 PPM O2 at 25ºC and 1 atm

Signal Output: 4-20mA non-isolated or 1-5V; optional Modbus Commu-

nication
Operating Range: 5ºC to 45ºC (GPR sensor), -10º to 45ºC (XLT sensor)

Warranty: 12 months analyzer; 12 months sensor

GPR-1500 DA

PPM Oxygen Analyzer

12-28 VDC Non-Loop or 110-220 VAC

Powered Oxygen Analyzer

Advanced Galvanic Sensor Technology with

Optional Sample Systems

2 Field Selectable Alarm Setpoints
12-28 VDC or 110-220 VAC Power
4-20 mA or 1-5V Signal Output
Sensitivity 0.5% Full Scale
4 Ranges Standard
Auto Ranging or Single Fixed
Stainless Steel Wetted Parts

Wetted Parts: Stainless steel

ISO 9001:2008 Certified

Optional Equipment

Sample conditioning system - Contact factory.

* Subject to change without notice

2855 Metropolitan Place, Pomona, CA 91767 USA ♦ Tel: [phone], Fax: [phone], www.aii1.com, e-mail: [e-mail] Rev 10/15

INTERTEK Certificate No. 485

GPR-1500 DA

ppm Oxygen Transmitter

Owner’s Manual

2855 Metropolitan Place, Pomona, CA 91767 USA ♦ Tel: [phone], Fax: [phone], e-mail: [e-mail], www.aii2.com

2

Table of Contents

Introduction

1

Quality Control Certification

2

Safety

3

Features & Specifications

4

Operation

5

Maintenance

6

Spare Parts

7

Troubleshooting

8

Warranty

9

Material Safety Data Sheets

10

Drawings

A/R

3

1 Introduction

Your new oxygen transmitter incorporated an advanced electrochemical sensor specific to oxygen along with state­of-the-art digital electronics designed to give you years of reliable precise oxygen measurements in variety of
industrial oxygen applications.

To obtain maximum performance from your new oxygen transmitter, please read and follow the guidelines
provided in this Owner’s Manual.

Every effort has been made to select the most reliable state of the art materials and components, to design the
transmitter for superior performance and minimal cost of ownership. This transmitter was tested thoroughly by the
manufacturer prior to shipment for best performance.

However, modern electronic devices do require service from time to time. The warranty included herein plus a staff
of trained professional technicians to quickly service your transmitter is your assurance that we stand behind every
transmitter sold.

The serial number of this transmitter may be found on the inside the transmitter. You should note the serial
number in the space provided and retains this Owner’s Manual as a permanent record of your purchase, for future
reference and for warranty considerations.

Serial Number: _______________________

Advanced Instruments Inc. appreciates your business and pledges to make every effort to maintain the highest
possible quality standards with respect to product design, manufacturing and service.

4

2 Quality Control Certification

Date:

Customer: Order No.: Pass

Model:

GPR-1500 DA ppm Oxygen Transmitter

Sensor:

( ) GPR-12-100-M ppm Oxygen Sensor
( ) XLT-12-100-M ppm Oxygen Sensor

Serial Nos.:

Transmitter ______________________ Sensor ______________________

Accessories:

Owner’s Manual

Configuration:

A-1151-E-A4 PCB Assembly Main Processing
A-1153-A-A4 PCB Assembly Alarms/Power Connection
Software rev:
Ranges: 0-100, 0-1000 ppm, 0-1%, 0-25%
Power: 12-36V DC two wire loop power
Barometric pressure and temperature compensation
NEMA 4X rated wall mount enclosures

Test: Pass Pass

Set default zero
Set default span @ 600uA or 300uA Alarm delay
Zero calibration Alarm bypass
Span Calibration Alarm configurations; ALARM 1, ALARM 2
Analog signal output 4-20mA full scale Alarm function; ALARM 1, ALARM 2
Calibrates with adequate span adjustment within 10-50% FS Alarm relays; ALARM 1, ALARM 2
Baseline drift on zero gas < ± 2% FS over 24 hour period Alarm system fail, dry contact
Noise level < ± 1.0% FS Overall inspection for physical defects

Options:
Notes:

5

3 Safety

General

This section summarizes the essential precautions applicable to the GPR-1500DA ppm Oxygen Transmitter.
Additional precautions specific to individual transmitter are contained in the following sections of this manual. To
operate the transmitter safely and obtain maximum performance follow the basic guidelines outlined in this
Owner’s Manual.

Caution: This symbol is used throughout the Owner’s Manual to Caution and alert the user to recommended
safety and/or operating guidelines.

Danger: This symbol is used throughout the Owner’s Manual to identify sources of immediate Danger such as
the presence of hazardous voltages.

Read Instructions: Before operating the transmitter read the instructions.
Retain Instructions: The safety precautions and operating instructions found in the Owner’s Manual should be

retained for future reference.

Heed Warnings: Follow all warnings on the transmitter, accessories (if any) and in this Owner’s Manual.
Follow Instructions: Observe all precautions and operating instructions. Failure to do so may result in personal

injury or damage to the transmitter.

Pressure and Flow

Inlet Pressure: GPR-1500DA ppm Oxygen Transmitters are designed for flowing samples, equipped with 1/8”
bulkhead tube fitting connections on the side of the unit (unless otherwise indicated, either fitting can serve as inlet
or vent) and are intended to operate at positive pressure regulated to between 5-30 psig.

Caution: If equipped with a H2S scrubber as part of an optional sample conditioning system, inlet pressure must
not exceed 30 psig.

Outlet Pressure: The sample gas vent pressure should be atmospheric.

Installation

Oxygen Sensor: DO NOT open the sensor. The sensor contains a corrosive liquid electrolyte that could be
harmful if touched or ingested, refer to the Material Safety Data Sheet contained in the Owner’s Manual appendix.
Avoid contact with any liquid or crystal type powder in or around the sensor or sensor housing, as either could be a
form of electrolyte. Leaking sensors should be disposed of in accordance with local regulations.

Mounting: The transmitter is approved for indoor or outdoor use. Mount as recommended by the manufacturer.
Power: Supply power to the transmitter only as rated by the specification or markings on the transmitter

enclosure. The wiring that connects the transmitter to the power source should be installed in accordance with
recognized electrical standards and so they are not pinched particularly near the power source and the point where
they attach to the transmitter. Never yank wiring to remove it from an outlet or from the transmitter.

Operating Temperature: The maximum operating temperature is 45º C.
Heat: Situate and store the transmitter away from sources of heat.
Liquid and Object Entry: The transmitter should not be immersed in any liquid. Care should be taken so that

liquids are not spilled into and objects do not fall into the inside of the transmitter.

6

Handling: Do not use force when using the switches and knobs. Before moving your transmitter be sure to
disconnect the wiring/power cord and any cables connected to the output terminals located on the transmitter.

Maintenance

Serviceability: Except for replacing the oxygen sensor, there are no parts inside the transmitter for the operator
to service.

Only trained personnel with the authorization of their supervisor should conduct maintenance.
Oxygen Sensor: DO NOT open the sensor. The sensor contains a corrosive liquid electrolyte that could be

harmful if touched or ingested, refer to the Material Safety Data Sheet contained in the Owner’s Manual appendix.
Avoid contact with any liquid or crystal type powder in or around the sensor or sensor housing, as either could be a
form of electrolyte. Leaking sensors should be disposed of in accordance with local regulations.

Troubleshooting: Consult the guidelines in Section 8 for advice on the common operating errors before
concluding that your transmitter is faulty.

Do not attempt to service the transmitter beyond those means described in this Owner’s Manual. Do not attempt to
make repairs by yourself as this will void the warranty as per Section 10 and may result in electrical shock, injury or
damage. All other servicing should be referred to qualified service personnel.

Cleaning: The transmitter should be cleaned only as recommended by the manufacturer. Wipe off dust and dirt
from the outside of the unit with a soft damp cloth then dry immediately. Do not use solvents or chemicals.

Nonuse Periods: If the transmitter is equipped with a range switch advance the switch to the OFF position and
disconnect the power when the transmitter is left unused for a long period of time.

4 Features & Specifications

See last page, this page left blank intentionally.

7

5 Operation

Principle of Operation

The GPR-1500DA oxygen transmitter incorporates a variety of ppm range advanced galvanic fuel cell type sensors.
The transmitter is configured in two sections. The transmitter is a compact efficient package configured with the
oxygen sensor and separate circuit boards for signal processing and terminals for incoming power, power supply,
signal output and alarm relay contacts housed in a general purpose NEMA 4X rated enclosure.

Advanced Galvanic Sensor Technology:

The sensors function on the same principle and are specific for oxygen. They measure the partial pressure of
oxygen from low ppm to 100% levels in inert gases, gaseous hydrocarbons, helium, hydrogen, mixed gases, acid
gas streams and ambient air. Oxygen, the fuel for this electrochemical transducer, diffusing into the sensor reacts
chemically at the sensing electrode to produce an electrical current output proportional to the oxygen concentration
in the gas phase. The sensor’s signal output is linear over all ranges and remains virtually constant over its useful
life. The sensor requires no maintenance and is easily and safely replaced at the end of its useful life.

Proprietary advancements in design and chemistry add significant advantages to an extremely versatile oxygen
sensing technology. Sensors for low ppm analysis recover from air to ppm levels in minutes, exhibit longer life and
reliable quality. The expected life of our new generation of percentage range sensors now range to five and ten
years with faster response times and greater stability. Another significant development involves expanding the
operating temperature range for percentage range sensors from -30°C to 50°C.

Electronics:

The signal generated by the sensor is processed by state of the art low power micro-processor based digital
circuitry. The first stage amplifies the signal. The second stage eliminates the low frequency noise. The third stage
employs a high frequency filter and compensates for signal output variations caused by ambient temperature
changes. The result is a very stable signal. Sample oxygen is analyzed very accurately. Response time of 90% of
full scale is less than 10 seconds (actual experience may vary due to the integrity of sample line connections, dead
volume and flow rate selected) on all ranges under ambient monitoring conditions. Sensitivity is typically 0.5% of
full scale low range. Oxygen readings may be recorded by an external device via the 0-1V signal output jack.

The circuit for the 4-20mA signal output and two adjustable alarms is powered by a DC/DC transformer that
requires a 12-36VDC power source and separate wiring for the outputs. A loop power source is not sufficient to
power to the circuit. The 4-20mA output is also represented on full scale oxygen readings to an external device.

Sample System:

The GPR-1500DA is supplied without a sample conditioning system thereby giving users the option of adding their
own or purchasing a factory designed sample conditioning system. Whatever the choice, the sample must be
properly presented to the sensor to ensure an accurate measurement. Users interested in adding their own sample
conditioning system should consult the factory. Advanced Instruments Inc. offers a full line of sample handling,
conditioning and expertise to meet your application requirements. Contact us at 909-392-6900 or e-mail us at

[e-mail]

8

Pressure & Flow

All electrochemical oxygen sensors respond to partial pressure changes in oxygen. The inlet pressure must always
be higher than the pressure at the outlet vent which is normally at atmospheric pressure.

Flow Through Configuration:

The sensor is exposed to sample gas that must flow or be drawn through
metal tubing inside the transmitter. The GPR-1500DA internal sample system
includes 1/8” compression tube inlet and vent fittings, a stainless steel sensor
housing with an o-ring seal to prevent the leakage of air and stainless steel
tubing.

Flow rates of 1-5 SCFH cause no appreciable change in the oxygen reading.
However, flow rates above 5 SCFH generate backpressure and erroneous
oxygen readings because the diameter of the integral tubing cannot evacuate
the sample gas at the higher flow rate. The direction the sample gas flows is
not important, thus either tube fitting can serve as the inlet or vent – just not
simultaneously.

A flow indicator with an integral metering valve upstream of the sensor is
recommended as a means of controlling the flow rate of the sample gas. A
flow rate of 2 SCFH or 1 liter per minute is recommended for optimum
performance.

Caution: Do not place your finger over the vent (it pressurizes the sensor) to
test the flow indicator when gas is flowing to the sensor. Removing your
finger (the restriction) generates a vacuum on the sensor and may damage the sensor (voiding the sensor
warranty).

To avoid generating a vacuum on the sensor (as described above) during operation, always select and install the
vent fitting first and remove the vent fitting last.

Application Pressure - Positive:

A flow indicator with integral metering valve positioned upstream of the sensor is recommended
for controlling the sample flow rate between 1-5 SCFH. To reduce the possibility of leakage for low
ppm measurements, position a metering needle valve upstream of the sensor to control the flow
rate and position a flow indicator downstream of the sensor.

If necessary, a pressure regulator (with a metallic diaphragm is recommended for optimum
accuracy, the use of diaphragms of more permeable materials may result in erroneous readings)
upstream of the flow control valve should be used to regulate the inlet pressure between 5-30
psig.

Caution: If equipped with a H2S scrubber as part of an optional sample conditioning system, inlet
pressure must not exceed 30 psig.

Application Pressure - Atmospheric or Slightly Negative:

For accurate ppm range oxygen measurements, an optional external sampling pump should be positioned
downstream of the sensor to draw the sample from the process, by the sensor and out to atmosphere. A flow
meter is generally not necessary to obtain the recommended flow rate with most sampling pumps.

Caution: If the transmitter is equipped with an optional flow indicator with integral metering valve or a metering
flow control valve upstream of the sensor - open the metering valve completely to avoid drawing a vacuum on the
sensor and placing an undue burden on the pump.

9

If pump loading is a consideration, a second throttle valve on the pump’s inlet side may be necessary to provide a
bypass path so the sample flow rate is within the above parameters.

To avoid erroneous oxygen readings and damaging the sensor:

¾ Do not place your finger over the vent (it pressurizes the sensor) to test the flow indicator when gas is flowing

to the sensor. Removing your finger (the restriction) generates a vacuum on the sensor and may damage the
sensor (voiding the sensor warranty).

¾ Assure there are no restrictions in the sample or vent lines
¾ Avoid drawing a vacuum that exceeds 14” of water column pressure – unless done gradually
¾ Avoid excessive flow rates above 5 SCFH which generate backpressure on the sensor.
¾ Avoid sudden releases of backpressure that can severely damage the sensor.
¾ Avoid the collection of particulates, liquids or condensation collect on the sensor that could block the diffusion

of oxygen into the sensor.

¾ If the transmitter is equipped with an optional integral sampling pump (positioned downstream of the sensor)

and a flow control metering valve (positioned upstream of the sensor), completely open the flow control
metering valve to avoid drawing a vacuum on the sensor and placing an undue burden on the pump.

10

Calibration & Accuracy

Single Point Calibration: As previously described the galvanic oxygen sensor generates an electrical current
sensor exhibiting an absolute zero, e.g. the sensor does not generate a current output in the absence of oxygen.
Given these linearity and absolute zero properties, single point calibration is possible.

Pressure: Because sensors are sensitive to the partial pressure of oxygen in the sample gas their output is a
function of the number of molecules of oxygen 'per unit volume'. Readouts in percent are permissible only when
the total pressure of the sample gas being analyzed remains constant. The pressure of the sample gas and that of
the calibration gas(es) must be the same (reality < 1-2 psi).

Temperature: The rate oxygen molecules diffuse into the sensor is controlled by a Teflon membrane otherwise
known as an 'oxygen diffusion limiting barrier' and all diffusion processes are temperature sensitive, the fact the
sensor's electrical output will vary with temperature is normal. This variation is relatively constant 2.5% per ºC. A
temperature compensation circuit employing a thermistor offsets this effect with an accuracy of +5% or better and
generates an output function that is independent of temperature. There is no error if the calibration and sampling
are performed at the same temperature or if the measurement is made immediately after calibration. Lastly, small
temperature variations of 10-15º produce < +1% error.

Accuracy:

In light of the above parameters, the overall accuracy of an transmitter is affected by two types of

errors: 1) those producing 'percent of reading errors', illustrated by Graph A below, such as +

5% temperature

compensation

circuit, tolerances of range resistors and the 'play' in the potentiometer used to make span

adjustments and 2) those producing 'percent of full scale errors', illustrated by Graph B, such as +1-2% linearity
errors in readout devices, which are really minimal due to today's technology and the fact that other errors are
'spanned out' during calibration.

Graph C illustrates these 'worse case' specifications that are typically used to develop an transmitter's overall
accuracy statement of +2% of full scale at constant temperature or +5% over the operating temperature range.
QC testing is typically <+0.5% prior to shipment.

11

Example: As illustrated by Graph A any error, play in the multi-turn span pot or the temperature compensation
circuit, during a span adjustment at 20.9% (air) of full scale range would be multiplied by a factor of 4.78
(100/20.9) if used for measurements of 95-100% oxygen concentrations. Conversely, an error during a span
adjustment at 100% of full scale range is reduced proportionately for measurements of lower oxygen
concentrations.

Recommendation: Calibrating with a span gas approximating 80% of the full scale range one or two ranges
higher than the full scale range of interest is recommended for 'optimum calibration accuracy'. Always calibrate at
the same temperature and pressure of the sample gas stream.

Start-up

The GPR-1500DA ppm Oxygen Transmitter has been calibrated at the factory prior to shipment and is fully
operational from the shipping container. The ppm oxygen sensor has been removed and packaged in a nitrogen
atmosphere to assure optimum performance. Once installed, we recommend the user allow the transmitters to
stabilize for 30 minutes and then recalibrate the device as instructed below.

Installation Considerations:

The GPR-1500DA consists of an electronic module that includes the terminals for incoming power and outgoing
signal outputs, and, the power supply, sensor housing; and, 1/8” sample inlet and vent connections housed in a
NEMA 4X rated enclosure.

For optimum accuracy zero and calibrate a ppm transmitter after it has been allowed to stabilize, typically 24-36
hours after installation. Assuming the initial zero is performed according to the procedure described herein, the
analyzer should not require zeroing again until the either the sensor is replaced or a change is made to the sample
system or gas lines. Following the initial zero and calibration, the analyzer should not require span calibration again
for up to 3 months under “normal” application conditions as described in the published specifications.

Note: As described below, zeroing the transmitter is recommended for measurements below 1 ppm. The low end
sensitivity (zero capability) has been verified at the factory; however, no ZERO OFFSET adjustment has been
made. A factory adjustment would be meaningless because of the difference in sample systems and leakage
factors between the factory set-up and the actual application conditions

1. Assemble the necessary hardware for mounting the transmitter and optional components - such as coalescing
or particulate filters and pumps, 1/8” metal or plastic tubing for interconnecting the transmitter and optional
components.

2. Review the application conditions to ensure the sample is suitable for analysis. Note: In natural gas
applications such as extraction and transmission, a low voltage current is applied to the pipeline itself to inhibit
corrosion. As a result, electronic devices can be affected unless adequately grounded.

12

3. Temperature: The sample must be sufficiently cooled before it enters the transmitter and any optional
components. A coiled 10 foot length of ¼” stainless steel tubing is sufficient for cooling sample gases as high
as 1,800ºF to ambient.

4. Pressure & Flow: As described above.

5. Moisture & Particulates: Prevent water and/or particulates from entering the sample system. They can clog the
tubing and damage the optional components such as pumps, scrubbers or sensors. Installation of a suitable
coalescing or particulate filter is required to remove condensation, moisture and/or particulates from the
sample gas to prevent erroneous analysis readings and damage to the sensor or optional components. Consult
the factory for recommendations concerning the proper selection and installation of components.

6. Contaminants: A gas scrubber and flow indicator with integral metering valve are required upstream of the
transmitter to remove interfering gases such as oxides of sulfur and nitrogen or hydrogen sulfide that can
produce false readings and reduce the expected life of the sensor. Installation of a suitable scrubber is required
to remove the contaminant from the sample gas to prevent erroneous analysis readings and damage to the
sensor or optional components. Consult the factory for recommendations concerning the proper selection and
installation of components.

7. Gas connections: Inlet and outlet vent gas lines require 1/8” diameter tubing preferably metal.

8. Power connection: Locate a source of AC power to meet area classification and to plug in the charging adapter.

9. Zero calibration (required only for very low percentage range measurements).

10. Span calibration – Users are responsible for certified span gas cylinder, regulator and flow control valve.

Mounting the Transmitter:

The GPR-1500DA is housed in a 9Hx4Wx3.5”D NEMA4X rated enclosure.
This configuration is designed to be mounted directly to any flat vertical
surface, wall or bulkhead plate with eight (8) of the appropriate screws. To
facilitate servicing the interior of the transmitters, position it approximately
5 feet off ground level.

1. Remove the four (4) screws securing the top section of the enclosure,
set them aside for reinstallation and raise the hinged top section 180º
until it locks in place.

2. Locate the mounting hole s cast into the enclosure.

3. Secure the enclosure to a vertical surface approximately 5 feet from the
floor or a level accessible to service personnel. This requires the user to
supply four (4) additional proper size screws and anchors.

4. Caution: Do not remove or discard the gaskets from either the
enclosure or junction box. Failure to reinstall either gasket will void the
NEMA 4 rating and RFI protection.

13

Gas Connections:

The GPR-1500DA with its standard flow through configuration is designed for positive pressure samples and
requires connections for incoming sample and outgoing vent lines. Zero and span inlet ports are offered as part of
the optional sample systems. The user is responsible for calibration gases and the required components, see
below.

Flow rates of 1-5 SCFH cause no appreciable change in the oxygen reading. However, flow rates above 5 SCFH
generate backpressure and erroneous oxygen readings because the diameter of the integral tubing cannot
evacuate the sample gas at the higher flow rate. A flow indicator with an integral metering valve upstream of the
sensor is recommended as a means of controlling the flow rate of the sample gas. A flow rate of 2 SCFH or 1 liter
per minute is recommended for optimum performance.

Caution: Do not place your finger over the vent (it pressurizes the sensor) to test the flow indicator when gas is
flowing to the sensor. Removing your finger (the restriction) generates a vacuum on the sensor and may damage
the sensor (voiding the sensor warranty).

Procedure:

1. Caution: Do not change the factory setting until instructed to do in this manual.

2. Designate one of the bulkh ead tube fittings as the VENT and the other SAMPLE.

3. Regulate the pressure as described in Pressure and Flow above.

4. Connect a 1/8” vent line to the compression fitting to be used for venting the sample.

5. Connect a 1/8” ZERO, SPAN or SAMPLE line to the fitting designated SAMPLE.

6. If equipped with optional fittings and/or sample system, connect the ZERO and SPAN gas lines.

7. Allow gas to flow through the transmitters and set the flow rate to 2 SCFH.

8. Note: If equipped with the optional H2S sample conditioning system, see drawing A-3237:

9. Regulate the pressure so that it does not exceed 30 psig

10. Use ¼” tubing to make the appropriate connections as labeled on the sample panel.

14

Electrical Connections:

Electrical connections to the GPR-1500DA are made at two different
locations within the transmitters.

Power requirements consist of a two wire shielded cable and a 12-36V
DC with negative ground power supply. Incoming power is connected
via a terminal strip found in the junction box on the left side of the
GPR-1500DA enclosure.

Caution: The integral 4-20mA converter is internally powered and
does not require external power. DO NOT supply any voltage to either
of the two terminals of the 4-20mA output or the 4-20mA converter
will be damaged.

To assure proper grounding, connect the 4-20mA signal output to the
external device (PLC, DCS, etc.) before attempting any zero or span
adjustments.

Procedure:

1. Remove the front cover of the junction box located on left side of
the transmitters by removing the four (4) screws securing the
cover and set them aside for reinstallation.

2. Loosen the n u t on the cable gland.

3. Separate the shielding from the wires of the cable.

4. Thread the wires through the cable gland into the inside of the junction box.

5. Connect the two wires to the two (2) screw type terminals of the barrier strip inside the junction box.

6. Ensure the positive and negative terminals of the power supply are connected to the appropriate terminals of
the barrier strip as marked.

7. Connect the shielding of the cable to the copper ground screw inside the junction box.

8. Replace the junction box cover ensuring the gaskets are in place and tighten the four (4) screws.

9. Tighten the cable gland to maintain NEMA 4 rating.

The incoming power from the external junction box is interconnected internally to the 24VDC terminal of the PCB
with the alarm and 4-20mA output terminals as illustrations below.

15

The 4-20mA signal output, power fail, alarm relay contacts, and, output connections are made to a terminal block
mounted on a PCB located in the bottom half of the front cover of the enclosure and appear upside when the
hinged enclosure is open and front cover swings up as illustrated below. The PCB also includes a transformer to
power the alarm relays. The main processing display PCB is located in the upper half of the front cover of the
enclosure.

To assure proper grounding, connect the 4-20mA signal output to the external device (PLC, DCS, etc.) before
attempting any zero or span adjustments.

Procedure:

1. Remove the four (4) screws securing the
protection Plexiglas guard.

2. Separate the shielding from the wires of
the cable.

3. Ensure the positive and negative
terminals of the incoming 24VDC power
supply are connected to the appropriate
terminals of the barrier strip as marked.

4. The output connections enter the GPR­1500DA from the hole provided in the
right side of the enclosure. Note: The
user is responsible for providing the
appropriate conduit and fittings.

5. Connect the shielding of the cable to the
ground screw. Note: The terminals snap
together, making it possible to detach the
section with the ground, install the
shielded cable and reinstall.

6. The 4-20mA current output is obtained
by connecting the current measuring
device between the positive and negative
terminals of the OUTPUT 4-20mA.

7. To check the signal output of the 4-20mA
E/I integrated circuit connect an ammeter
as the measuring device and confirm the
output is within +

8. Replace the protective Plexiglas guard
and secure.

Caution: To assure proper grounding,
connect the 4-20mA signal output to the
external device (PLC, DCS, etc.) before
attempting any zero or span adjustments.

0.1mA of 4mA.