Analog Microelectronics AME1085DCBT, AME1085AMCT, AME1085ACDT-3, AME1085ACDT, AME1085ACBT Datasheet
...
Analog Microelectronics, Inc.
1
AME1085
3A Low Dropout
Positive Voltage Regulator
nn
nn
n Applications
ll
ll
l High Efficiency Linear Regulators
ll
ll
l Post Regulators for Switching Supplies
ll
ll
l 5V to 3.3V Voltage Converter
ll
ll
l Battery Charger
nn
nn
n Functional Block Diagram
Thermal
Protection
Bandgap
Reference
Current
Limiting
Amplifier
Input
Output
ADJ/GND
Error
Amp.
nn
nn
n General Description
The AME1085 is a 3A low-dropout positive voltage regulator. It is available in fixed and adjustable output voltage
versions. Overcurrent and thermal protection are integrated onto the chip. Output current will limit as it reaches
the pre-set current or temperature limit. At full rated
output current the dropout voltage is 1.4V (max.).
AME1085 series regulators provide excellent regulation
over line, load and temperature variations.
nn
nn
n Key Features
l Low dropout voltage 1.2V typically at 3A
ll
ll
l Adjustable or 3.3V fixed voltage
ll
ll
l Line regulation typically 0.015%
ll
ll
l Load regulation typically 0.05%
ll
ll
l Adjust pin (ADJ) current less than 90υA
ll
ll
l Overcurrent protection
ll
ll
l Thermal protection
ll
ll
l Available in TO-220, TO-263, TO-252
Figure 1
nn
nn
n Typical Application
Figure 2
AME1085
Load
10µF Tan
10
µ
F Tan
4.75V to 5.25V
V
IN
GND
V
OUT
Analog Microelectronics, Inc.
2
AME1085
3A Low Dropout
Positive Voltage Regulator
TO-252-2 Front view
23
ADJ/
GND
V
OUT
V
IN
nn
nn
n Pin Configuration
AME1085
1
To-252-2 Front View
1
2
3
AME 1085
ADJ/GND
V
OUT
V
IN
To-263 Front View
1
2
3
AME 1085
ADJ/GND
V
OUT
V
IN
1
2
3
AME 1085
ADJ/GND
V
OUT
V
IN
To-263-2 Front View
Analog Microelectronics, Inc.
3
AME1085
3A Low Dropout
Positive Voltage Regulator
nn
nn
n Absolute Maximum Ratings
nn
nn
n Ordering Information
Symbol M aximum Units
V
IN
7V
TO-220
2.5
TO-263
2.5
TO-252
15
TO-220
50
TO-263
60
TO-252
90
Thermal Resistance
(Junction to Case)
St orage Temperature Range
Operating Junction Temperature Range
Parameter
0
C
θ
JC
0
C/W
T
LEAD
260
θ
JA
Thermal Resistance
(Juncti on t o A m bient)
Lead Temperature ( 10 sec )
Input Volt age
T
J
0 to 125
T
STG
-65 t o 15 0
Part Number Marking Output Voltage Package
AME1085ACBT
AME1085
ACBT
YYWW
ADJ TO-220
AME1085DCBT
AME1085
DCBT
YYWW
3.3 TO-220
AME1085ACDT-3
AME1085
ACDT-3
YYWW
ADJ TO-263-3
AME1085DCDT -3
AME1085
DCDT-3
YYWW
3.3 TO-263-3
AME1085ACDT
AME1085
ACDT
YYWW
ADJ TO-263-2
AME1085DCDT
AME1085
DCDT
YYWW
3.3 TO-263-2
AME 1085AM CT
AME1085
AMCT
YYWW
ADJ TO-252-2
AME1085MCT*
AME1085
MCT
YYWW
3.3 TO-252-2
* This differs from our standard part numbering sc hem e due to hi s t oric al precedent
Analog Microelectronics, Inc.
4
AME1085
3A Low Dropout
Positive Voltage Regulator
nn
nn
n Electrical Characteristics
AME1085DXXX
AME1085AXXX
Parameter Symbol Min. Typ. Max. Units
Reference voltage V
IN
= 5V TJ =250C 1.238 1.262
(adjustable voltage) I
O
= 10mA Over temp. 1.225 1.275
V
IN
= 2.75 - 7V TJ =250C - 0.015 0.2
I
O
= 10mA Over temp. - 0.035 0.2
V
IN
= 5V TJ =250C - 0.05 0.3
I
O
= 10mA - 3A Over tem p. - 0.2 0. 4
Dropout voltage V
IN
= 2.75 - 7V TJ =250C-1.21.4
∆V
OUT
, ∆V
REF
= 1% IO = 10mA - 3A Over tem p. - 1.3 -
Current limit I
S
3.0 - - A
Temperature Coefficient T
C
-0.005-
%/
O
C
Temperature stabili ty T
S
VIN = 5V, IO = 500mA, Over temp. - 0.5 - %
Minimum load current I
O
-510mA
RMS out put nois e V
N
-0.003- %V
0
Ripple rej ection ratio
R
A
VIN = 5V, IO = 3A, Over temp.
60 72 - dB
Test Conditions
V
REF
1.250 V
Line regulation Reg
LINE
%
Load regulation Reg
LOAD
%
V
D
V
V
IN
= 2.75 - 7V, Over temp.
V
IN
= 2.75 - 7V, IO = 10mA - 3A
V
IN
= 5V
T
J
=250C
Parameter Symbol Min. Typ. Max. Units
Output voltage V
IN
= 5V TJ =250C 3.267 3.333
(fix ed voltage) I
O
= 0A Over temp. 3.234 3.366
V
IN
=4.5 - 7V TJ =250C - 0.015 0.2
I
O
= 0A Over temp. - 0.035 0.2
V
IN
= 5V TJ =250C - 0.05 0.3
I
O
= 0A - 3A Over temp. - 0.2 0. 4
Dropout voltage V
IN
= 4.5 - 7V TJ =250C-1.21.4
∆V
OUT
, ∆V
REF
= 1% IO = 0A - 3A Over temp. - 1.3 -
Current limit I
S
3.0 - - A
Quies cent current
(fix ed m odel)
Temperature Coefficient T
C
-0.005-
%/
0
C
Temperature stabili ty T
S
VIN = 5V, IO = 500mA, Over temp. - 0.5 - %
RMS out put nois e V
N
-0.003- %V
0
Ripple rej ection ratio
R
A
VIN = 5V, IO = 3A, Over temp.
60 72 - dB
Test Conditions
Vo 3.300 V
Line regulation Reg
LINE
%
Load regulation Reg
LOAD
%
V
D
V
V
IN
= 4.5 - 7V, Over temp.
I
Q
V
IN
= 5V , Io=0A - 3A, Over temp. -
T
J
=250C
12 13 mA
V
IN
= 4.5 - 7V, IO = 0A - 3A
Analog Microelectronics, Inc.
5
AME1085
3A Low Dropout
Positive Voltage Regulator
nn
nn
n Application Description
1. Output voltage adjustment
Like most regulators, the AME1085 regulates the
output by comparing the output voltage to an
internally generated reference voltage. On the
adjustable version, the VREF is available externally as 1.25V between V
OUT
and ADJ. The
voltage ratio formed by R1 and R2 should be
set to conduct 10mA (minimum output load).
The output voltage is given by the following
equation:
V
OUT
= V
REF
( 1 + ) + I
ADJ
x R2
On fixed versions of AME1085, the voltage divider is provided internally.
R2
R1
Figure 3
2. Thermal protection
AME1085 has thermal protection which limits
junction temperature to 150OC. However, device functionality is only guaranteed to a maximum junction temperature of +125OC.
The power dissipation and junction temperature
for AME1085 in TO-220 package are given by
PD = (VIN - V
OUT
) x I
OUT
T
JUNCTION
= T
AMBIENT
+ ( PD x θJA)
Note: T
JUNCTION
must not exceed 125OC
3. Current limit protection
AME1085 is protected against overload conditions. Current protection is triggered at typically 4.5A.
4. Stability and load regulation
AME1085 requires a capacitor from VOUT to
GND to provide compensation feedback to the
internal gain stage. This is to ensure stability
at the output terminal. Typically, a 10µF tanta-
lum or 50µF aluminum electrolytic is sufficient.
Note: It is important that the ESR for this capacitor does not exceed 0.5Ω.
The output capacitor dose not have a theoretical upper limit and increasing its value will increasestability. COUT = 100µF or more is typical for high current regulator design.
For the adjustable version, the best load regulation is accomplished when the top of the
resistor divider (R1) is connected directly to the
output pin of the AME1085. When so connected, RP is not multiplied by the divider ratio.
For fixed output versions, the top of R1 is internally connected to the output and ground
pin can be connected to low side of the load.
Figure 4
V
OUT
= V
REF
(1+
R2
R1
) + I
ADJ
x R2
OUT
ADJ
IN
V
REF
I
ADJ
50µA
V
IN
V
OUT
R1
R2
C
1
OUT
ADJ
IN
V
IN
R1
R2
R
L
R
P
Parasitic
Line Resistance
Connect
R2 to load
(Connect R1 to case)
Analog Microelectronics, Inc.
6
AME1085
3A Low Dropout
Positive Voltage Regulator
5. Thermal consideration
The AME1085 series contain thermal limiting circuitry designed to protect itself for over-temperature conditions. Even for normal load conditions,
maximum junction temperature ratings must not
be exceed. As mention in thermal protection
section, we need to considerall sources of thermal resistance between junction and ambient.
It includes junction-to-case, case-to-heat-sink interface and heat sink thermal resistance itself.
Junction-to-case thermal resistance is specified
from the IC junction to the bottom of the case
directly below the die. Proper mounting is required to ensure the best possible thermal flow
from this area of the package to the heat sink.
The case of all devices in this series is electrically connected to the output. Therefore, if the
case of the device must be electrically isolated,
a thermally conductive spacer is recommended.
Analog Microelectronics, Inc.
7
AME1085
3A Low Dropout
Positive Voltage Regulator
nn
nn
n Advanced Applications
* VO = VREF ( 1 + ) + IADJ x R2
** Optional for improved ripple rejection
R2
R1
Figure 5 Adjustable output voltage
* 20mΩ is ballast resistance
The inter - connection of #18 wire could act as ballast resistance
Figure 6 Paralleling Regulators
V
IN
= 5V
R1
R2
10µF
10
µ
F
2K
1K
10µF
**
* VO = 1.5 - 3.45V
AME1085
V
OUT
V
IN
ADJ
V
IN
R1
R2
10µF
V
O
10µF
I
O
= 0 to 6A
* 20m
Ω
* 20m
Ω
AME1085
V
OUT
V
IN
GND
AME1085
V
OUT
V
IN
GND
Analog Microelectronics, Inc.
8
AME1085
3A Low Dropout
Positive Voltage Regulator
nn
nn
n Advanced Applications (Cont.)
* VO = VREF + VZ (VZ: breakdown voltage of Zener diode)
** Optional for improved ripple rejection
Figure 7 Regulator with reference
Figure 8 Regulator with reverse diode protection
V
IN
10µF
10
µ
F
1K
10µF
**
AME1085
V
OUT
V
IN
GND
10µF
100
µ
F
V
O
*
AME1085
V
OUT
V
IN
GND
Analog Microelectronics, Inc.
9
AME1085
3A Low Dropout
Positive Voltage Regulator
R1(ohm) 100 102 105 107 110 113 115 118 121 124
Vout
1.25 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000
1.30 3.984 4.063 4.182 4.262 4.381 4.500 4.579 4.698 4.817 4.936
1.35 7.968 8.127 8.365 8.524 8.761 8.999 9.158 9.396 9.633 9.871
1.40 11.95 12.19 12.55 12.79 13.14 13.50 13.74 14.09 14.45 14.81
1.45 15.94 16.25 16.73 17.05 17.52 18.00 18.32 18.79 19.27 19.74
1.50 19.92 20.32 20.91 21.31 21.90 22.50 22.89 23.49 24.08 24.68
1.55 23.90 24.38 25.09 25.57 26.28 27.00 27.47 28.19 28.90 29.61
1.60 27.89 28.44 29.28 29.83 30.67 31.50 32.05 32.88 33.72 34.55
1.65 31.87 32.51 33.46 34.09 35.05 36.00 36.63 37.58 38.53 39.48
1.70 35.86 36.57 37.64 38.36 39.43 40.50 41.21 42.28 43.35 44.42
1.75 39.84 40.63 41.82 42.62 43.81 45.00 45.79 46.98 48.17 49.36
1.80 43.82 44.70 46.01 46.88 48.19 49.50 50.37 51.68 52.98 54.29
1.85 47.81 48.76 50.19 51.14 52.57 54.00 54.95 56.37 57.80 59.23
1.90 51.79 52.82 54.37 55.40 56.95 58.50 59.53 61.07 62.62 64.16
1.95 55.78 56.89 58.55 59.66 61.33 63.00 64.11 65.77 67.43 69.10
2.00 59.76 60.95 62.74 63.93 65.71 67.49 68.68 70.47 72.25 74.03
2.05 63.75 65.01 66.92 68.19 70.09 71.99 73.26 75.17 77.07 78.97
2.10 67.73 69.08 71.10 72.45 74.47 76.49 77.84 79.86 81.88 83.90
2.15 71.71 73.14 75.28 76.71 78.85 80.99 82.42 84.56 86.70 88.84
2.20 75.70 77.21 79.47 80.97 83.23 85.49 87.00 89.26 91.52 93.77
2.25 79.68 81.27 83.65 85.24 87.61 89.99 91.58 93.96 96.33 98.71
2.30 83.67 85.33 87.83 89.50 92.00 94.49 96.16 98.65 101.2 103.6
2.35 87.65 89.40 92.01 93.76 96.38 98.99 100.7 103.4 106.0 108.6
2.40 91.63 93.46 96.20 98.02 100.8 103.5 105.3 108.1 110.8 113.5
2.45 95.62 97.52 100.4 102.3 105.1 108.0 109.9 112.7 115.6 118.5
2.50 99.60 101.6 104.6 106.5 109.5 112.5 114.5 117.4 120.4 123.4
2.55 103.6 105.6 108.7 110.8 113.9 117.0 119.1 122.1 125.2 128.3
2.60 107.6 109.7 112.9 115.1 118.3 121.5 123.6 126.8 130.1 133.3
2.65 111.6 113.8 117.1 119.3 122.7 126.0 128.2 131.5 134.9 138.2
2.70 115.5 117.8 121.3 123.6 127.0 130.5 132.8 136.2 139.7 143.1
2.75 119.5 121.9 125.5 127.9 131.4 135.0 137.4 140.9 144.5 148.1
2.80 123.5 126.0 129.7 132.1 135.8 139.5 141.9 145.6 149.3 153.0
2.85 127.5 130.0 133.8 136.4 140.2 144.0 146.5 150.3 154.1 157.9
2.90 131.5 134.1 138.0 140.6 144.6 148.5 151.1 155.0 159.0 162.9
2.95 135.5 138.2 142.2 144.9 148.9 153.0 155.7 159.7 163.8 167.8
3.00 139.4 142.2 146.4 149.2 153.3 157.5 160.3 164.4 168.6 172.7
3.05 143.4 146.3 150.6 153.4 157.7 162.0 164.8 169.1 173.4 177.7
3.10 147.4 150.3 154.8 157.7 162.1 166.5 169.4 173.8 178.2 182.6
R2(ohm)=(Vout-1.25)*R1/(1.25+50u*R1)
nn
nn
n External Rsistor Divider Table for Customized Voltage
Analog Microelectronics, Inc.
10
AME1085
3A Low Dropout
Positive Voltage Regulator
External Rsistor Divider Table for Customized Voltage (Cont.)
R1(ohm) 100 102 105 107 110 113 115 118 121 124
Vout
3.15 151.4 154.4 158.9 161.9 166.5 171.0 174.0 178.5 183.0 187.5
3.20 155.4 158.5 163.1 166.2 170.8 175.5 178.6 183.2 187.9 192.5
3.25 159.4 162.5 167.3 170.5 175.2 180.0 183.2 187.9 192.7 197.4
3.30 163.3 166.6 171.5 174.7 179.6 184.5 187.7 192.6 197.5 202.4
3.35 167.3 170.7 175.7 179.0 184.0 189.0 192.3 197.3 202.3 207.3
3.40 171.3 174.7 179.8 183.3 188.4 193.5 196.9 202.0 207.1 212.2
3.45 175.3 178.8 184.0 187.5 192.8 198.0 201.5 206.7 211.9 217.2
3.50 179.3 182.9 188.2 191.8 197.1 202.5 206.1 211.4 216.8 222.1
3.55 183.3 186.9 192.4 196.0 201.5 207.0 210.6 216.1 221.6 227.0
3.60 187.3 191.0 196.6 200.3 205.9 211.5 215.2 220.8 226.4 232.0
3.65 191.2 195.0 200.8 204.6 210.3 216.0 219.8 225.5 231.2 236.9
3.70 195.2 199.1 204.9 208.8 214.7 220.5 224.4 230.2 236.0 241.8
3.75 199.2 203.2 209.1 213.1 219.0 225.0 228.9 234.9 240.8 246.8
3.80 203.2 207.2 213.3 217.3 223.4 229.5 233.5 239.6 245.7 251.7
3.85 207.2 211.3 217.5 221.6 227.8 234.0 238.1 244.3 250.5 256.6
3.90 211.2 215.4 221.7 225.9 232.2 238.5 242.7 249.0 255.3 261.6
3.95 215.1 219.4 225.9 230.1 236.6 243.0 247.3 253.7 260.1 266.5
4.00 219.1 223.5 230.0 234.4 240.9 247.5 251.8 258.4 264.9 271.5
4.05 223.1 227.6 234.2 238.7 245.3 252.0 256.4 263.1 269.7 276.4
4.10 227.1 231.6 238.4 242.9 249.7 256.5 261.0 267.8 274.6 281.3
4.15 231.1 235.7 242.6 247.2 254.1 261.0 265.6 272.5 279.4 286.3
4.20 235.1 239.7 246.8 251.4 258.5 265.5 270.2 277.2 284.2 291.2
4.25 239.0 243.8 250.9 255.7 262.8 270.0 274.7 281.9 289.0 296.1
4.30 243.0 247.9 255.1 260.0 267.2 274.5 279.3 286.6 293.8 301.1
4.35 247.0 251.9 259.3 264.2 271.6 279.0 283.9 291.3 298.6 306.0
4.40 251.0 256.0 263.5 268.5 276.0 283.5 288.5 296.0 303.5 310.9
4.45 255.0 260.1 267.7 272.8 280.4 288.0 293.1 300.7 308.3 315.9
4.50 259.0 264.1 271.9 277.0 284.7 292.5 297.6 305.4 313.1 320.8
4.55 262.9 268.2 276.0 281.3 289.1 297.0 302.2 310.1 317.9 325.7
4.60 266.9 272.2 280.2 285.5 293.5 301.5 306.8 314.8 322.7 330.7
4.65 270.9 276.3 284.4 289.8 297.9 306.0 311.4 319.5 327.5 335.6
4.70 274.9 280.4 288.6 294.1 302.3 310.5 315.9 324.2 332.4 340.6
4.75 278.9 284.4 292.8 298.3 306.7 315.0 320.5 328.8 337.2 345.5
4.80 282.9 288.5 297.0 302.6 311.0 319.5 325.1 333.5 342.0 350.4
4.85 286.9 292.6 301.1 306.8 315.4 324.0 329.7 338.2 346.8 355.4
4.90 290.8 296.6 305.3 311.1 319.8 328.5 334.3 342.9 351.6 360.3
4.95 294.8 300.7 309.5 315.4 324.2 333.0 338.8 347.6 356.4 365.2
5.00 298.8 304.8 313.7 319.6 328.6 337.5 343.4 352.3 361.3 370.2
R2(ohm)=(Vout-1.25)*R1/(1.25+50u*R1)
Analog Microelectronics, Inc.
11
AME1085
3A Low Dropout
Positive Voltage Regulator
nn
nn
n Package Dimension
TO-252 (DP AK) -EIAJ
TO-252 (DPAK) JDEC
MIN MAX MIN MAX
A 0.45 0.58 0.0177 0.023
B 1.60 1.95 0.06 0.0768
C 0.51 - 0.02 -
D 0.45 0.60 0.0177 0.0236
E 6.40 6.80 0.252 0.2677
F 5.40 5.80 0.2126 0.2283
G 2.20 2.85 0.0866 0.1122
H - * 2.30 - * 0.0906
I - 0.90 - 0.0354
J - 0.97 - 0.038
K 5.20 5.50 0.20 0.22
L 0.89 2.03 0.035 0.08
* : Ty pical valu e
NOTES :
1. CONTROLLING DIMENSION : MILLIMETERS.
2. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS
MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE
MATERIAL.
SY MBO L S
MILLIMETERS INCHES
MIN MAX MIN MAX
A 0.45 0.58 0.0177 0.023
B 1.60 1.95 0.06 0.0768
C0.51 - 0.02 -
D 0.45 0.60 0.0177 0.0236
E 6.40 6.80 0.252 0.2677
F 5.40 5.80 0.2126 0.2283
G 2.20 2.85 0.0866 0.1122
H - * 2.30 - * 0.0906
I - 0.90 - 0.0354
J - 0.97 - 0.038
K 5.20 5.50 0.20 0.22
L 0.89 2.03 0.035 0.08
* : Ty pical value
NOTES :
1. CONTROLLING DIMENSION : MILLIMETE RS.
2. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS
MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE
MATERIAL.
SY MBOL S
MILLIMETERS INCHES
Analog Microelectronics, Inc.
12
AME1085
3A Low Dropout
Positive Voltage Regulator
nn
nn
n Package Dimension
TO-220
TO-263-3 (D2PAK)
MIN MAX MIN MAX
A 4.06 4.83 0.160 0.190
b 0.63 1.02 0.025 0.040
C1 0.35 0.60 0.0138 0.0236
D 14.22 14.99 0.056 0.590
E 9.66 10.54 0.385 0.415
e - 2.79 - 0.110
e1 4.83 5.33 0.190 0.210
e3 1.14 1.40 0.045 0.055
f 1.14 1.40 0.045 0.055
H1 5.94 6.55 0.234 0.258
K 2.29 2.92 0.090 0.115
CP 3.71 3.96 0.146 0.156
Q 2.62 2.87 0.103 0.113
L 12.70 14.27 0.500 0.5618
a 3D7D3D7D
b1 1.14 1.52 0.0449 0.06
R
Notes :
1. Dimension C1 apply for tin plate finish.
2. For solder dip lead finish dimension C1 should be
0.015"-0.027" (0.38-0.69)
6.17 REF. 0.243 REF.
SYMBOLS
MILLIMETERS INCHES
MIN MAX MIN MAX
A 9.65 10.41 0.380 0.410
B 8.28 9.65 0.326 0.380
C 4.06 4.83 0.160 0.190
D 0.51 1.02 0.020 0.040
E 1.14 1.40 0.045 0.055
G
H 14.61 15.88 0.575 0.625
K 1.02 1.68 0.040 0.066
L 0.00 0.97 0.000 0.038
M 2.49 2.74 0.098 0.108
N 0.43 0.58 0.017 0.023
P 2.29 2.79 0.090 0.110
R
0
o
8
?
0
o
8
?
S 2.41 2.67 0.095 0.105
W 0.254 0.508 0.010 0.020
*
: Typical value
NOTES :
1. CONTROLLING DIMENSION : MILLIMETERS.
2MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH
THICKNESS
MINIMUM L EA D THICKNESS IS TH E MINI MUM
THICKNESS OF BASE MATERIA.
*
2.54
*
0.100
SY MBO LS
MILLIMETERS INCHES
Analog Microelectronics, Inc.
13
AME1085
3A Low Dropout
Positive Voltage Regulator
nn
nn
n Package Dimension
TO-263-2 (D2PAK)
MIN MAX MIN MAX
A 9.65 10.41 0.380 0.410
B 8.28 9.65 0.326 0.380
C 4.06 4.83 0.160 0.190
D 0.51 1.02 0.020 0.040
E 1.14 1.40 0.045 0.055
G
H 14.61 15.88 0.575 0.625
K 1.02 1.68 0.040 0.066
L 0.00 0.97 0.000 0.038
M 2.49 2.74 0.098 0.108
N 0.43 0.58 0.017 0.023
P 2.29 2.79 0.090 0.110
R
0
o
8
?
0
o
8
?
S 2.41 2.67 0.095 0.105
W 0.254 0.508 0.010 0.020
*
: Typical value
NOTES :
1. CONTROLLING DIMENSION : MILLIMETERS.
2MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH
THICKNESS
MINIMU M LE AD T HICKNESS IS TH E MINIMUM
THICKNESS OF BASE MATERIA.
*
2.54
*
0.100
SY MBO L S
MILLIMETERS INCHES
Life Support Policy:
These products of Analog Microelectronics, Inc. are not authorized for use as critical components in life-
support devices or systems, without the express written approval of the president
of Analog Microelectronics, Inc.
Analog Microelectronics, Inc. reserves the right to make changes in the circuitry and specifications of its
devices and advises its customers to obtain the latest version of relevant information.
Analog Microelectronics, Inc. , July 2001
Document: 1013-duc-B-0704
Corporate Headquarters Asia Pacific Headquarters
Analog Microelectronics, Inc. AME, Inc.
3100 De La Cruz Blvd. Suite 201 2F, 187 Kang-Chien Road, Nei-Hu Dist.,
Santa Clara, CA. 95054-2046 Taipei 114, Taiwan, R.O.C.
Tel : (408) 988-2388 Tel : 886 2 2627-8687
Fax: (408) 988-2489 Fax : 886 2 2659-2989
www.analogmicro.com
E-Mail: info@analogmicro.com
Loading...