Evaluation Board User Guide
UG-163
One Technology Way • P. O . Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel : 781.329.4700 • Fax : 781.461.3113 • www.analog.com
GSM900 Evaluation Board for PLL Frequency Synthesizer
FEATURES
Self-contained board including synthesizer, VCO, and loop
filter, for generating GSM frequencies (819 MHz to 915 MHz)
Designed for 20 kHz loop bandwidth
Accompanying software allows complete control of
synthesizer functions from a PC
Battery operated: choice of 3 V or 5 V supplies
Typical phase noise performance of −91 dBc/Hz at 1 kHz offset
Typical spurious performance of better than −90 dBc at
200 kHz offset from carrier
EVALUATION BOARD CONNECTION DIAGRAM
GENERAL DESCRIPTION
The EVAL-ADF411xEBZ1 is designed to allow users to evaluate
the performance of the ADF4113 frequency synthesizer for phase
lock loops (PLLs). The block diagram of the board is shown in
Figure 1. It contains the ADF4113 synthesizer, a pc connector,
an SMA connector for the reference input, power supplies, and
an RF output. There is also a loop filter (20 kHz bandwidth)
and an on-board VCO. A cable is included with the board to
connect to a PC printer port.
The package also contains Windows® software to allow easy
programming of the synthesizer.
TCXO
9V BATTERY
POWER SWITCH
ON OFF
FILTER
ADF411x
EVAL-ADF411xEBZ1
PC CONNECTO R
Figure 1.
V
P
MUXOUT
CE
9148-001
V
DD
V
VCO
TEST
SMA
SOCKET
VCO
TEST
RF
OUT
REF
IN
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 8
UG-163 Evaluation Board User Guide
TABLE OF CONTENTS
Features.............................................................................................. 1
General Description ......................................................................... 1
Evaluation Board Connection Diagram........................................ 1
Revision History ............................................................................... 2
Evaluation Board Hardware............................................................ 3
REVISION HISTORY
5/11—Revision 0: Initial Version
Hardware Description ..................................................................3
Evaluation Board Software...............................................................4
Software Description ....................................................................4
Programmable Software Settings................................................4
Evaluation Board Schematics...........................................................5
Rev. 0 | Page 2 of 8
Evaluation Board User Guide UG-163
V
A
EVALUATION BOARD HARDWARE
RF
through a standard SMA connector. Users can use their
HARDWARE DESCRIPTION
The evaluation board comes with a cable for connecting it to
the printer port of a PC. The silkscreen and cable diagram for
the evaluation board are shown in Figure 2 and Figure 3. The
board schematics are shown in Figure 5 and Figure 6.
Figure 2. Evaluation Board Silkscreen
The board is powered from a single 9 V battery. The power supply
circuitry allows the user to choose either 3 V or 5 V for the
ADF4113 V
are 3 V for the ADF4113 V
VCO supply. Note that the ADF4113 V
the ADF4113 V
and VP, and for the VCO supply. The default settings
DD
, and 5 V for the ADF4113 VP and
DD
should never exceed
DD
because it can damage the device. All components
P
necessary for LO generation are on board. The 13 MHz TCXO
from Vectron provides the necessary reference input. The PLL is
made up of the ADF4113, a passive loop filter (20 kHz bandwidth),
and the VCO190-902T from Vari-L. The output is available at
09148-002
OUT
own power supplies and reference input. In this case, they need
to insert SMA connectors as shown on the silkscreen and block
diagram.
Loop filter components include the following:
• C1 = 470 pF
• C2 = 4.7 nF
• C3 = 20 pF
• R1 = 7.5 kΩ
• R2 = 20 kΩ
E
L-ADF411x
EVAL-ADF421x
1
6
2
7
3
8
4
9
5
9-WAY
FEMALE D-TYPE
TO
ADF411x
ADF421x
EVALUATION
BOARD
BLACK-CLK
BROWN-DATA
ORANGE-CE
WHITE-GND
YELLOW
1
2
3
RED-LE
4
5
6
7
8
9
BLUE
10
11
12
PURPLE
13
25-WAY
MALE D-TYPE
PC PRINTER PORT
TO
14
15
16
17
18
19
20
21
22
23
24
25
PC
09148-003
Figure 3. PC Cable Diagram
Loop component values shown in the circuit diagram are for a
900 MHz RF output, 5 mA CP current, VCO190-902T, 200 kHz
channel spacing, and 20 kHz loop bandwidth.
Rev. 0 | Page 3 of 8
UG-163 Evaluation Board User Guide
EVALUATION BOARD SOFTWARE
SOFTWARE DESCRIPTION
The evaluation board comes with the software on a CD. The
software is suitable for all the ADF411x devices. To install, use
the following steps:
1. Click Setup.exe. The install wizard installs the software.
Note that administrator access is required on the PC to
install the software.
2. Follow the on-screen directions. The software is installed
in a default directory: C:/Program Files/Analog Devices.
To run t he s of twar e, c li ck ADF4XXX_revx.
Prior to the Main Interface Page, a window appears to select
the device being evaluated. Choose the ADF4113EBZ1 and
click OK. The Main Interface Page now appears (see Figure 4).
The synthesizer is now programmed with the correct settings for a
GSM system working at 900 MHz. A 200 kHz PFD frequency is
set up, a 32/33 prescaler is chosen, and a charge pump current
of 5 mA is programmed.
PROGRAMMABLE SOFTWARE SETTINGS
To program the software, complete the following:
1. Click REF IN Frequency, insert the desired frequency in
MHz, and click OK.
2. Click RF VCO Output Frequency for the Output
Frequency window to appear. Enter the Output
Frequency and click OK.
3. Click PFD Frequency, insert the desired frequency in kHz,
and click OK.
4. Click RF Charge Pump Current Setting 2 or RF Charge
Pump Current Setting 1 and the current setting window
will appear. Enter the value used for the loop filter and
click OK.
5. Click RF PD Polarity Positive to set the PD polarity bit to
positive, which ensures that all registers are loaded.
At this point, the data is now set up, and the user can modify other
features.
The software also allows monitoring of the device supply voltage,
supply current, and the charge pump voltage. Click Update Voltage
and Current Display to get an up-to-date reading.
Figure 4. Software Front Panel
Rev. 0 | Page 4 of 8
09148-006
Evaluation Board User Guide UG-163
EVALUATION BOARD SCHEMATICS
09148-004
Figure 5. Evaluation Board Circuit Diagram (Page 1)
Rev. 0 | Page 5 of 8
UG-163 Evaluation Board User Guide
Figure 6. Evaluation Board Circuit Diagram (Page 2)
09148-005
Rev. 0 | Page 6 of 8
Evaluation Board User Guide UG-163
NOTES
Rev. 0 | Page 7 of 8
UG-163 Evaluation Board User Guide
NOTES
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the pers onal jurisdiction and venu e of such courts. The United Nations Conventi on on Contracts for the Internation al Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG09148-0-5/11(0)
Rev. 0 | Page 8 of 8
Loading...