Analog Devices BSD830-DG, BSD830-AG, BHD930-AG, BHD930-DG, BSC730 User Manual
User’s Manual
BROAD SCAN HD
MODEL: BHD930-AG & BHD930-DG
BROAD SCAN SDI
MODEL: BSD830-AG & BSD830-DG
BROAD SCAN
MODEL: BSC730
ANALOG WAY® BROAD SCAN (HD/SDI) – AW 5002 EDITION : 07 / 07
BROAD SCAN (HD/SDI)
SAFETY INSTRUCTIONS
All of the safety and operating instructions should be read before the product is operated and should be retained for further
reference. Please follow all of the warnings on this product and its operating instructions.
ENGLISH
CAUTION
:
WARNING: To prevent the risk of electric shock and fire, do not expose this device to rain, humidity or intense
heat sources (such as heaters or direct sunlight). Slots and openings in the device are provided for
ventilation and to avoid overheating. Make sure the device is never placed on or near a textile
surface that could block the openings. Also keep away from excessive dust, vibrations and shocks.
POWER: Only use the power supply indicated on the device or on the power source. Devices equipped with a
grounding plug should only be used with a grounding type outlet. In no way should this grounding
be modified, avoided or suppressed.
POWER CORD: Use the On (I) / Off (O) switch to power On or Off devices equipped with that switch. All other
devices should be plugged and unplugged from wall outlet. In both cases, please follow these
instructions:
- The power cord of the device should be unplugged from the outlet when left unused for several
days.
- To unplug the device, do not pull on the power cord but always on the plug itself.
- The outlet should always be near the device and easily accessible.
- Power supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them.
If the power supply cord is damaged, unplug the device. Using the device with a damaged power
supply cord may expose you to electric shocks or other hazards. Verify the condition of the power
supply cords once in a while. Contact your dealer or service center for replacement if damaged.
CONNECTIONS: All inputs and outputs (except for the power input) are TBTS defined under EN60950.
SERVICING: Do not attempt to service this product yourself by opening or removing covers and screws since it
may expose you to electric shocks or other hazards. Refer all problems to qualified service
personnel.
OPENINGS: Never push objects of any kind into this product through the openings. If liquids have been spilled or
objects have fallen into the device, unplug it immediately and have it checked by a qualified
technician.
PAGE 2
BROAD SCAN (HD/SDI)
Ç
INSTRUCTIONS DE SÉCURITÉ
Afin de mieux comprendre le fonctionnement de cet appareil nous vous conseillons de bien lire toutes les consignes de sécurité et de fonctionnement de
l’appareil avant utilisation. Conserver les instructions de sécurité et de fonctionnement afin de pouvoir les consulter ultérieurement. Respecter toutes les
consignes marquées dans la documentation, sur le produit et sur ce document.
ATTENTION : Afin de prévenir tout risque de choc électrique et d’incendie, ne pas exposer cet appareil à la pluie, à l’humidité et aux sources de chaleur
intense.
INSTALLATION : Veillez à assurer une circulation d’air suffisante pour éviter toute surchauffe à l’intérieur de l’appareil. Ne placez pas l’appareil sur ou
proximité de surface textile susceptible d’obstruer les orifices de ventilation. N’installez pas l’appareil à proximité de sources de chaleur comme un radiateur
ou une bouche d’air chaud, ni dans un endroit exposé au rayonnement solaire direct, à des poussières excessives, à des vibrations ou à des chocs mécaniques.
Ceci pourrait provoquer un mauvais fonctionnement et un accident.
ALIMENTATION : Ne faire fonctionner l’appareil qu’avec la source d’alimentation indiquée sur l’appareil ou sur son bloc alimentation. Pour les appareils
équipés d’une alimentation principale avec fil de terre, ils doivent être obligatoirement connectés sur une source équipée d’une mise à la terre efficace. En
aucun cas cette liaison de terre ne devra être modifiée, contournée ou supprimée.
CORDON D’ALIMENTATION : Pour les appareils équipés d’un interrupteur général (Marche I / Arrêt O), la mise sous tension et la mise hors tension se fait
en actionnant cet interrupteur général. Pour les appareils sans interrupteur général, la mise sous tension et la mise hors tension se fait directement en
connectant et déconnectant le cordon d'alimentation de la prise murale.
Dans les 2 cas ci-dessus appliquer les consignes suivantes :
- Débrancher le cordon d'alimentation de la prise murale si vous prévoyez de ne pas utiliser l'appareil pendant quelques jours ou plus.
- Pour débrancher le cordon, tirez le par la fiche. Ne tirez jamais sur le cordon proprement dit.
- La prise d’alimentation doit se trouver à proximité de l’appareil et être aisément accessible.
- Ne laissez pas tomber le cordon d’alimentation et ne posez pas d’objets lourds dessus.
Si le cordon d’alimentation est endommagé, débranchez le immédiatement de la prise murale. Il est dangereux de faire fonctionner cet appareil avec un cordon
endommagé, un câble abîmé peut provoquer un risque d’incendie ou un choc électrique. Vérifier le câble d’alimentation de temps en temps. Contacter votre
revendeur ou le service après vente pour un remplacement.
CONNEXIONS : Toutes les entrées et sorties (exceptée l’entrée secteur) sont de type TBTS (Très Basse Tension de Sécurité) définies selon EN 60950.
RÉPARATION ET MAINTENANCE : L’utilisateur ne doit en aucun cas essayer de procéder aux opérations de dépannage, car l’ouverture des appareils par
retrait des capots ou de toutes autres pièces constituant les boîtiers ainsi que le dévissage des vis apparentes à l’extérieur, risque d’exposer l’utilisateur à des
chocs électriques ou autres dangers. Contacter le service après vente ou votre revendeur ou s’adresser à un personnel qualifié uniquement.
OUVERTURES ET ORIFICES : Les appareils peuvent comporter des ouvertures (aération, fentes, etc...), veuillez ne jamais y introduire d’objets et ne jamais
obstruer ses ouvertures. Si un liquide ou un objet pénètre à l’intérieur de l’appareil, débranchez immédiatement l’appareil et faites le contrôler par un personnel
qualifié avant de le remettre en service.
ISTRUZIONI DI SICUREZZA
Allo scopo di capire meglio il funzionamento di questa apparecchiatura vi consigliamo di leggere bene tutti i consigli di sicurezza e di funzionamento prima
dell’utilizzo. Conservare le istruzioni di sicurezza e di funzionamento al fine di poterle consultare ulteriormente. Seguire tutti i consigli indicati su questo
manuale e sull’apparecchiatura.
ATTENZIONE : Al fine di prevenire qualsiasi rischio di shock elettrico e d’incendio, non esporre l’apparecchiatura a pioggia, umidità e a sorgenti di
eccessivo calore.
INSTALLAZIONE : Assicuratevi che vi sia una sufficiente circolazione d’aria per evitare qualsiasi surriscaldamento all’interno dell’apparecchiatura. Non
collocare l’apparecchiatura in prossimità o su superfici tessili suscettibili di ostruire il funzionamento della ventilazione. Non installate l’apparecchiatura in
prossimità di sorgenti di calore come un radiatore o una fuoruscita d’aria calda, né in un posto esposto direttamente ai raggi del sole, a polvere eccessiva, a
vibrazioni o a shock meccanici. Ció potrebbe provocare un erroneo funzionamento e un incidente.
ALIMENTAZIONE : Far funzionare l’apparecchiatura solo con la sorgente d’alimentazione indicata sull’apparecchiatura o sul suo alimentatore. Per le
apparecchiature fornite di un’alimentazione principale con cavo di terra, queste devono essere obbligatoriamente collegate su una sorgente fornita di una
efficiente messa a terra. In nessun caso questo collegamento potrà essere modificato, sostituito o eliminato.
CAVO DI ALIMENTAZIONE : Per le apparecchiature fornite di interruttore generale (Acceso I / Spento O), l’accensione e lo spegnimento
dell’apparecchiatura si effettuano attraverso l’interruttore. Per le apparecchiature senza interruttore generale, l’accensione e lo spegnimento si effettuano
direttamente inserendo o disinserendo la spina del cavo nella presa murale.
In entrambe i casi applicare i seguenti consigli :
- Disconnettere l’apparecchiatura dalla presa murale se si prevede di non utilizzarla per qualche giorno.
- Per disconnettere il cavo tirare facendo forza sul connettore.
- La presa d’alimentazione deve trovarsi in prossimità dell’apparecchiatura ed essere facilmente accessibile.
- Non far cadere il cavo di alimentazione né appoggiarci sopra degli oggetti pesanti.
Se il cavo di alimentazione é danneggiato, spegnere immediatamente l’apparecchiatura. E’ pericoloso far funzionare questa apparecchiatura con un cavo di
alimentazione danneggiato, un cavo graffiato puó provocare un rischio di incendio o uno shock elettrico. Verificare il cavo di alimentazione spesso. Contattare
il vostro rivenditore o il servizio assistenza per una sostituzione.
CONNESSIONE : Tutti gli ingressi e le uscite (eccetto l’alimentazione) sono di tipo TBTS definite secondo EN 60950.
RIPARAZIONI E ASSISTENZA : L’utilizzatore non deve in nessun caso cercare di riparare l’apparecchiatura, poiché con l’apertura del coperchio metallico o
di qualsiasi altro pezzo costituente la scatola metallica, nonché svitare le viti che appaiono esteriormente, poiché ció puó provocare all’utilizzatore un rischio
di shock elettrico o altri rischi.
APERTURE DI VENTILAZIONE : Le apparecchiature possono comportare delle aperture di ventilazione, si prega di non introdurre mai oggetti o ostruire le
sue fessure. Se un liquido o un oggetto penetra all’interno dell’apparecchiatura, disconnetterla e farla controllare da personale qualificato prima di rimetterla in
servizio.
AIS ITALIANO
FRAN
PAGE 3
BROAD SCAN (HD/SDI)
SICHERHEITSHINWEISE
Um den Betrieb dieses Geräts zu verstehen, raten wir Ihnen vor der Inbetriebnahme alle Sicherheits- und Betriebsanweisungen genau zu lesen. Diese
Sicherheits- und Betriebsanweisungen für einen späteren Gebrauch sicher aufbewahren. Alle in den Unterlagen, an dem Gerät und hier angegebenen
Sicherheitsanweisungen einhalten.
VORSICHT & WARNUNG
ACHTUNG: um jegliches Risiko eines Stromschlags oder Feuers zu vermeiden, das Gerät nicht Regen, Feuchtigkeit oder intensiven Wärmequellen aussetzen.
EINBAU: Eine ausreichende Luftzufuhr sicherstellen, um jegliche Überhitzung im Gerät zu vermeiden. Das Gerät nicht auf und in Nähe von
Textiloberflächen, die Belüftungsöffnungen verschließen können, aufstellen. Das Gerät nicht in Nähe von Wärmequellen, wie z.B. Heizkörper oder
Warmluftkappe, aufstellen und es nicht dem direkten Sonnenlicht, übermäßigem Staub, Vibrationen oder mechanischen Stößen aussetzen. Dies kann zu
Betriebsstörungen und Unfällen führen.
STROMVERSORGUNG: Das Gerät nur mit der auf dem Gerät oder dem Netzteil angegebenen Netzspannung betreiben. Geräte mit geerdeter
Hauptstromversorgung müssen an eine Stromquelle mit effizienter Erdung angeschlossen werden. Diese Erdung darf auf keinen Fall geändert, umgangen oder
entfernt werden.
STROMKABEL: Für Geräte mit einem Hauptschalter (Ein/Aus) erfolgt die Stromversorgung und Unterbrechung mittels dieses Hauptschalters. Geräte ohne
Hauptschalter werden durch das Einstecken oder Herausziehen des Steckers in den Wandanschluß ein- oder ausgeschaltet. Für beide Fälle gelten folgende
Richtlinien:
- Den Stecker aus dem Wandanschluß herausziehen wenn Sie das Gerät mehrere Tage oder länger nicht benutzen.
- Das Kabel mittels dem Stecker herausziehen. Niemals am Stromkabel selbst ziehen.
- Die Steckdose muß sich in der Nähe des Geräts befinden und leicht zugänglich sein.
- Das Stromkabel nicht fallen lassen und keine schweren Gegenstände auf es stellen.
Wenn das Stromkabel beschädigt ist, das Gerät sofort abschalten. Es ist gefährlich das Gerät mit einem beschädigten Stromkabel zu betreiben; ein abgenutztes
Kabel kann zu einem Feuer oder Stromschlag führen. Das Stromkabel regelmäßig untersuchen. Für den Ersatz, wenden Sie sich an Ihren Verkäufer oder
Kundendienststelle.
ANSCHLÜSSE: Bei allen Ein- und Ausgängen (außer der Stromversorgung) handelt es sich, gemäß EN 60950, um Sicherheits- Kleinspannunganschlüsse.
REPARATUR UND WARTUNG : Der Benutzer darf keinesfalls versuchen das Gerät selbst zu reparieren, die Öffnung des Geräts durch Abnahme der
Abdeckhaube oder jeglichen anderen Teils des Gehäuses sowie die Entfernung von außen sichtbaren Schrauben zu Stromschlägen oder anderen Gefahren für
den Benutzer führen kann. Wenden Sie sich an Ihren Verkäufer, Ihre Kundendienststelle oder an qualifizierte Fachkräfte.
ÖFFNUNGEN UND MUNDUNGEN: Die Geräte können über Öffnungen verfügen (Belüftung, Schlitze, usw.). Niemals Gegenstände in die Öffnungen
einführen oder die Öffnungen verschließen. Wenn eine Flüssigkeit oder ein Gegenstand in das Gerät gelangt, den Stecker herausziehen und es vor einer neuen
Inbetriebnahme von qualifiziertem Fachpersonal überprüfen lassen.
INSTRUCCIONES DE SEGURIDAD
Para comprender mejor el funcionamiento de este aparato, le recomendamos que lea cuidadosamente todas las consignas de seguridad y de funcionamiento del
aparato antes de usarlo. Conserve las instrucciones de seguridad y de funcionamiento para que pueda consultarlas posteriormente. Respete todas las consignas
indicadas en la documentación, relacionadas con el producto y este documento.
PRECAUCIONES Y OBSERVACIONES
CUIDADO : Para prevenir cualquier riesgo de choque eléctrico y de incendio, no exponga este aparato a la lluvia, a la humedad ni a fuentes de calorintensas.
INSTALACIÓN : Cerciórese de que haya una circulación de aire suficiente para evitar cualquier sobrecalentamiento al interior del aparato. No coloque el
aparato cerca ni sobre una superficie textil que pudiera obstruir los orificios de ventilación. No instale el aparato cerca de fuentes de calor como radiador o
boca de aire caliente, ni en un lugar expuesto a los rayos solares directos o al polvo excesivo, a las vibraciones o a los choques mecánicos. Esto podría
provocar su mal funcionamiento o un accidente.
ALIMENTACIÓN : Ponga a funcionar el aparato únicamente con la fuente de alimentación que se indica en el aparato o en su bloque de alimentación. Los
aparatos equipados con una alimentación principal con hilo de tierra deben estar conectados obligatoriamente a una fuente equipada con una puesta a tierra
eficaz. Por ningún motivo este enlace de tierra deberá ser modificado, cambiado o suprimido.
ESPAÑOL DEUTSCH
CABLE DE ALIMENTACIÓN : Para los aparatos equipados con un interruptor general (Marcha I / Paro O), la puesta bajo tensión y la puesta fuera de tensión
se hace accionando este interruptor general.. En los aparatos que no tienen interruptor general, la puesta bajo tensión y la puesta fuera de tensión se hace
directamente conectando y desconectando el enchufe mural.
En ambos casos, se deberá respetar las siguientes consignas:
- Desconectar el aparato del enchufe mural si no piensa utilizarlo durante varios días.
- Para desconectar el cable, tire de la clavija. No tire nunca del cable propiamente dicho.
- El enchufe de alimentación debe estar cerca del aparato y ser de fácil acceso.
- No deje caer el cable de alimentación ni coloque objetos pesados encima de él.
Si el cable de alimentación sufriera algún daño, ponga el aparato inmediatamente fuera de tensión. Es peligroso hacer funcionar este aparato con un cable
averiado, ya que un cable dañado puede provocar un incendio o un choque eléctrico. Verifique el estado del cable de alimentación de vez en cuando. Póngase
en contacto con su distribuidor o con el servicio de posventa si necesita cambiarlo.
CONEXIONES : Todas las entradas y salidas (excepto la entrada del sector) son de tipo TBTS (Muy Baja Tensión de Seguridad) definidas según EN 60950.
REPARACIÓN Y MANTENIMIENTO : Por ningún motivo, el usuario deberá tratar de efectuar operaciones de reparación, ya que si abre los aparatos
retirando el capó o cualquier otra pieza que forma parte de las cajas o si destornilla los tornillos aparentes exteriores, existe el riesgo de producirse una
explosión, choques eléctricos o cualquier otro incidente. Contacte el servicio de posventa, a su distribuidor o dirigirse con personal cualificado únicamente.
ABERTURAS Y ORIFICIOS : Los aparatos pueden contener aberturas (aireación, ranuras, etc.). No introduzca allí ningún objeto ni obstruya nunca estas
aberturas. Si un líquido o un objeto penetra al interior del aparato, desconéctelo y hágalo revisar por personal cualificado antes de ponerlo nuevamente en
servicio.
PAGE 4
BROAD SCAN (HD/SDI)
TABLE OF CONTENTS
SAFETY INSTRUCTIONS...........................................................................................................................................................
2
QUICK START GUIDE – BROAD SCAN (HD/SDI)..................................................................................................................6
Chapter 1 : INTRODUCTION.......................................................................................................................................................7
1-1. ACCESSORIES SUPPLIED ..............................................................................................................................................7
1-2. BROAD SCAN HD GENERAL INFORMATION............................................................................................................7
1-3. BROAD SCAN SDI INFORMATION...............................................................................................................................8
1-4. BROAD SCAN INFORMATION......................................................................................................................................9
1-5. DEVICES & OPTIONS REFERENCES............................................................................................................................9
1-6. INSTALLATION................................................................................................................................................................9
1-7. BROAD SCAN HD (BHD930) & BROAD SCAN SDI (BSD830) FRONT PANEL DESCRIPTION ..........................10
1-8. BROAD SCAN HD (BHD930) REAR PANEL DESCRIPTION....................................................................................11
1-9. BROAD SCAN SDI (BSD830) REAR PANEL DESCRIPTION....................................................................................12
1-10. BROAD SCAN (BSC730) FRONT PANEL DESCRIPTION .......................................................................................13
1-11. BROAD SCAN (BSC730) REAR PANEL DESCRIPTION..........................................................................................14
Chapter 2 : STARTING ...............................................................................................................................................................15
2-1. BROAD SCAN CONNECTIONS....................................................................................................................................15
2-2. SETTINGS........................................................................................................................................................................16
2-3. IMAGE ADJUSTMENTS................................................................................................................................................16
2-4. EMBEDDED AUDIO MODE..........................................................................................................................................16
Chapter 3 : USING FRAME STORE AND LOGO INSERTION (BHD930 & BSD830) ..........................................................17
3-1. LOGO INSERTION .........................................................................................................................................................17
3-2. USING THE FRAME STORE .........................................................................................................................................18
Chapter 4 : FRONT PANEL DISPLAY MENU DESCRIPTION...............................................................................................19
4-1. INTRODUCTION ............................................................................................................................................................19
4-2. CONTROL BUTTONS ....................................................................................................................................................19
4-3. STATUS MODE...............................................................................................................................................................19
4-4. CONTROL MODE...........................................................................................................................................................20
4-5. FUNCTIONS DESCRIPTION .........................................................................................................................................22
Chapter 5 : UPDATING THE DEVICE ......................................................................................................................................29
5-1. CONNECTIONS ..............................................................................................................................................................29
5-2. UPDATE INSTRUCTIONS.............................................................................................................................................29
Chapter 6 : REMOTE CONTROL SOFTWARE.........................................................................................................................30
6-1. CONNECTIONS ..............................................................................................................................................................30
6-2. SOFTWARE INSTALLATION:......................................................................................................................................30
6-3. COMMUNICATION SETUP...........................................................................................................................................30
6-4. USING THE SOFTWARE...............................................................................................................................................31
Chapter 7 : TECHNICAL SPECIFICATIONS............................................................................................................................34
7-1. COMPUTER INPUTS......................................................................................................................................................34
7-2. VIDEO OUTPUTS...........................................................................................................................................................34
7-3. ANALOG GENLOCK (MODELS: BHD930-AG, BSD830-AG & BSC730).................................................................36
7-4. DIGITAL GENLOCK (MODELS: BHD930-DG & BSD830-DG).................................................................................36
7-5. COMMUNICATION PORTS ..........................................................................................................................................36
7-6. ENVIRONMENTAL........................................................................................................................................................37
APPENDIX A: PROGRAMMER'S GUIDE................................................................................................................................38
WARRANTY...............................................................................................................................................................................45
PAGE 5
QUICK START GUIDE – BROAD SCAN (HD/SDI)
ANALOG WAY EDITION : 07/07
CONNECTIONS:
c Turn OFF all of your equipment before connecting.
d Connect the AC power supply cord to the BROAD SCAN and to an AC power outlet.
e Connect your computer sources to the COMPUTER INPUT (HD15) connector or the DVI-D INPUT connector.
f As required, connect a control monitor on the MONITOR OUT (HD15 or DVI-D) connector.
NOTE:
NOTE:
The analog (RGB) MONITOR OUT is available only if the COMPUTER source is analog.
The DVI-D MONITOR OUT is available only if the COMPUTER source is DVI-D.
g Connect your display device (TV monitor, VCR...) to the outputs (analog or SDI*).
h Turn ON the BROAD SCAN (rear panel switch). Then turn ON your input source and then your display devices.
* The SDI outputs are available on BHD930 & BSD830 models only.
• Example of connection (Model: BHD930-AG):
6
2
4
3
4
5
5 5
• RGB/COMPONENT output connection:
SETTINGS:
c We recommend resetting the BROAD SCAN to all of its default values, with the front panel display menu
(CONTROLdefault valueyes) before proceeding.
d Select the auto-setting menu with the front panel display menu (INPUTAuto setting) and activate this function with
ENTER. This function detects automatically the input type of the source connected to the input connectors (DVI &
RGB). Then the device performs an auto-centering function.
e Select the Input status menu (INPUTInput status) to verify the correct detection of the type and format of your input
source. If a wrong message is displayed, select manually the type of your input source (INPUTInput Type).
f Select the output format and rate (OUTPUTFormat).
g For SDTV output format (PAL, NTSC) select the type of the RGB/YCrCb output (OUTPUTType).
h Perform the needed image adjustments, available in the IMAGE menu.
BROAD SCAN (HD/SDI)
BROAD SCAN (HD/SDI)
Chapter 1 : INTRODUCTION
1-1. ACCESSORIES SUPPLIED
• 1 BROAD SCAN or BROAD SCAN SDI or BROAD SCAN HD
• 1 AC mains cable.
• 1 CD-ROM (Remote Control Software).
• 1 User’s Manual.
1-2. BROAD SCAN HD GENERAL INFORMATION
Broad Scan HD by Analog Way is a Broadcast and Professional Computer to Video and High Definition TV Scan
Converter. Fitted with Digital DVI and Analog RGB input, it converts Workstation, PC or Mac graphic images up to
1600x1200 @ 60Hz (1920x1200 RB) into Video or HDTV. Each computer input has its own monitor loopthrough out
for the connection of a control display. Output signal can be both analog and digital thus Broad Scan HD can provide a
full Digital signal processing path from the input to the output.
Broad Scan HD features a powerful broadcast Genlock. Two versions of the Broad Scan HD offer either a Digital
HD/SD-SDI Genlock (Model BHD930-DG) or an Analog HD Black or Black Burst Genlock (Model BHD930-AG).
Genlock input is fitted with a loop through output allowing chaining devices. The user can adjust phase and subcarrier
delay according to the specific installation requirements. HD output formats can also be genlocked with a SDTV Black
Burst signal. All Genlock timings meet broadcast ITU/SMPTE standards.
Broad Scan HD supports many Output formats as listed below:
HDTV
• 720p @ 60, 59.94 & 50 Hz (SMPTE 296M),
• 1080i @ 60, 59.94 & 50 Hz (SMPTE 274M),
• 1035i @ 60 Hz & 59.94 Hz (SMPTE 260M),
• 1080sF @ 30, 29.97 & 25 Hz (RP2H/SMPTE 274M),
• 1080p @ 30, 29.97, 25, 24, 23.98 Hz (RP2H/SMPTE 274M).
SDTV
• NTSC – 525i @ 60 & 59.94 Hz – 15.735 kHz - ITU / RS170-A
• PAL– 625i @ 50 Hz – 15.625 kHz – CCIR
Broad Scan HD outputs different signals at the same time in one selected output format:
• In HDTV: Two HD-SDI and one HD-YUV 3 level sync signals are available simultaneously.
• In SDTV NTSC/PAL: Two SDI, one YUV or RGB, one S.Video and one Composite Video signals are available
simultaneously.
Broad Scan HD also outputs a Luma Key signal in both Digital and Analog format. Luma key is at the same format as
the output and is perfectly synchronized. In addition, a Frame Lock output allows synchronizing external device frame
rate such as some graphic cards.
Broad Scan HD features real time conversion with high performance Image Processing. User adjustments offer an AntiFlicker filter to significantly reduce flickering of the interlaced HD/SD-TV outputs, as well as 2D Sharpness, RGB level
and Black level. It converts single wire computer type signal into black and white video image just by setting a menu.
The state of the art high speed hardware FPGA allows aspect ratio control and a wide range linear or nonlinear zoom up
to 1000%. In addition, a new “zoom finder” is provided to preview the actual part of the picture to be zoomed (H, V and
H&V simultaneously). Broad Scan HD also offers a Frame Memory to store a full screen image that can be displayed at
any time, as well as 1 animated or 4 still logos.
Broad Scan HD allows embedding analog audio Stereo signal into the HD/SD-SDI signal (fs = 48 kHz @ 20/24 bits),
with matched A/V delay.
Broad Scan HD is designed to be User Friendly thanks to many direct access functions such as Freeze, Frame,
Under/Over scan, Aspect Ratio, Zoom position and size. It also provides easy to use and efficient menus on a clear
bright blue LCD screen. LCD continuously displays Input and Output status during operations.
Broad Scan HD includes Computer input format memory: Up to 16 user presets are stored in the machine
corresponding to 16 different input formats. The exact adjustments of the frequently used formats are instantly recalled,
which makes the Broad Scan HD ideal and very useful for multi-computer applications or rental.
PAGE 7
Chapter 1 : INTRODUCTION (continued) BROAD SCAN (HD/SDI)
1-3. BROAD SCAN SDI INFORMATION
Broad Scan SDI by Analog Way is a Broadcast and Professional Computer to Video Scan Converter. Fitted with Digital
DVI and Analog RGB input, it converts Workstation, PC or Mac graphic images up to1600x1200 @ 60Hz (1920x1200
RB) into NTSC or PAL Video.
Each Computer input has its own monitor loopthrough output for the connection of a control display. Output signal can
be both Analog and Digital, thus Broad Scan SDI can provide a full Digital signal processing path from the input to the
output.
Broad Scan SDI features a powerful Broadcast Genlock. Two versions of the Broad Scan SDI offer either a Digital SDI
Genlock (ModelBSD830-DG) or an Analog Black Burst Genlock(Model BSD830-AG). Genlock input is fitted with a
loop through output allowing to daisy chain devices. The user can adjust phase and subcarrier delay according to
specific installation requirements. All Genlock timings meet broadcast ITU/SMPTE standards.
Broad Scan SDI output formats are:
• NTSC – 525i @ 60 & 59.94 Hz – 15.735 kHz - ITU / RS170-A,
• PAL– 625i @ 50 Hz – 15.625 kHz – CCIR.
Broad Scan SDI outputs different signals at the same time in one selected output format NTSC or PAL: Two 10 Bits
SDI, one YUV or RGB, one S.Video and one Composite Video signals are available simultaneously.
Broad Scan SDI also outputs Luma Key signal in both Digital and Analog signals. The Luma key signal comes in the
same format as the output and perfectly timed. In addition, a Frame Lock output allows synchronizing an external
device frame rate such as a graphic card.
Broad Scan SDI features real time conversion with high performance Image Processing. User adjustments offer an AntiFlicker filter to significantly reduce flickering of the interlaced TV out-puts, as well as 2D Sharpness, RGB level and
Black level. It converts single wire Computer type signal into black and white Video image just by setting a menu. The
state of the art high speed hardware FPGA allows aspect ratio control and a wide linear or non linear zoom capability up
to 1000%. In addition, a new highlighted “zoom finder” is provided to preview the actual part of the picture to be
zoomed (H, V and H&V simultaneously). Broad Scan SDI also offers a Frame Memory to store a full screen image that
can be displayed at any time as well as 1 animated or 4 still logos.
Broad Scan SDI allows embedding Analog Audio Stereo input signal into the SDI output signal (fs=48 kHz @ 20/24
bits), with matched A/V delay, adjustable level, balance and mute.
Broad Scan SDI is designed to be User Friendly thanks to many direct access functions such as Freeze, Frame,
Under/Over scan, Aspect Ratio, Zoom position and size. It also has easy to use and efficient menus on a clear bright
blue LCD screen. LCD continuously displays Input and Output status during operation.
Broad Scan SDI includes Computer input format memory: Up to 16 user presets are stored in the device corresponding
to 16 different input for-mats. The exact adjustments of the frequently used formats are instantly recalled which makes
the Broad Scan SDI ideal and very useful for multi-computer applications or rental.
PAGE 8
BROAD SCAN (HD/SDI) Chapter 1 : INTRODUCTION (continued)
1-4. BROAD SCAN INFORMATION
Broad Scan by Analog Way is a Broadcast and Professional Computer to Video Scan Converter. Fitted with Digital
DVI and Analog RGB input, it converts Workstation, PC or Mac graphic images up to1600x1200 @ 60Hz (1920x1200
RB) into NTSC or PAL video. Each computer input has its own monitor loop through output for the connection of a
control display.
Broad Scan features a powerful broadcast Genlock through a NTSC or PAL Black Burst. Genlock input is fitted with a
loop through output allowing to daisy chain devices. The user can adjust phase and subcarrier delay according to a
specific installation requirements. All Genlock timings meet broadcast ITU/SMPTE standards.
Broad Scan output formats are:
• NTSC – 525i @ 60 & 59.94 Hz – 15.735 kHz - ITU / RS170-A
• PAL– 625i @ 50 Hz – 15.625 kHz – CCIR
Broad Scan outputs different signals at the same time in one selected output format NTSC or PAL: one YUV or RGB,
one S.Video and one Composite Video signals are available simultaneously.
Broad Scan also outputs Luma Key signal. The Luma key signal comes in the same format as the output and perfectly
timed. In addition, a Frame Lock output allows synchronizing an external device frame rate such as a graphic card.
Broad Scan features real time conversion with high performance Image Processing. User adjustments offer an AntiFlicker filter to significantly reduce flickering of the interlaced TV outputs, as well as 2D Sharpness, RGB level and
Black level. It converts single wire computer type signal into black and white video image just by setting a menu. The
state of the art high speed hardware FPGA allows aspect ratio control and a wide linear or non linear zoom capability up
to1000%. In addition, a new highlighted “zoom finder” is provided to preview the actual part of the picture to be
zoomed (H, V and H&V simultaneously).
Broad Scan is designed to be User Friendly thanks to many direct access functions such as Freeze, Black, Under/Over
scan, Aspect Ratio, Zoom position and size. It also has easy to use and efficient menus on a clear bright blue LCD
screen. LCD continuously displays Input and Output status during operation.
Broad Scan includes Computer input format memory: Up to 16 user presets are stored in the device corresponding to 16
different input for-mats. The exact adjustments of the frequently used formats are instantly recalled which makes the
Broad Scan ideal and very useful for multi-computer applications or rental.
1-5. DEVICES & OPTIONS REFERENCES
REFERENCE DESIGNATION
BHD930-AG BROAD SCAN HD with analog genlock.
BHD930-DG BROAD SCAN HD with digital genlock.
BSD830-AG BROAD SCAN SDI with analog genlock.
BSD830-DG BROAD SCAN SDI with digital genlock.
BSC730 BROAD SCAN.
OPT-LAN Optional IP/LAN communication port.
1-6. INSTALLATION
IMPORTANT:
• Table Top Mounting
• Rack Mounting:
Please read all the safety instructions (pages 2 to 4) before starting.
The devices can be used directly on a table: they are equipped with 4 plastic feet.
The devices are compatibles with a 19" enclosure. To install the device into a 19” rack: Attach
the device to the rack by using 4 screws in the front panel holes (screws are not included).
Connect all of the cables to the devices and attach them to the rack with some tie wraps.
IMPORTANT:
• The openings in the rear and side panels are for cooling. Do not cover these openings.
• B e sure th at n o wei gh t is ad ded ont o the device in excess of 2 kg (4.4 lbs.).
• The maximum ambient operating temperature must not exceed 40°C (104°F).
• The rack and all mounted equipment in it must be reliably grounded to national and
local electrical codes.
PAGE 9
Chapter 1 : INTRODUCTION (continued) BROAD SCAN (HD/SDI)
1-7. BROAD SCAN HD (BHD930) & BROAD SCAN SDI (BSD830) FRONT PANEL DESCRIPTION
• BROAD SCAN HD
ANALOG WAY
R
Broad
Scan
HD
• BROAD SCAN SDI
R
ANALOG WAY
ON / OFF: Switch ON or OFF the device (Long push).
FRAME: Frame selection. Display the stored frame onto the output.
FREEZE: Freezes the displayed output.
UNDER/OVER: Image mode selection.
ASPECT RATIO: Aspect ratio selection.
1/1: The image and aspect ratio of the source are preserved.
Cropped: The image is resized and the borders are cut to fill full the screen (The aspect ratio is
preserved).
Full Screen: The image is stretched to fill full the screen without cutting the borders (The aspect ratio is
not preserved).
PAN & ZOOM
POS. SIZE: Position or Size mode selection.
H: Horizontal image adjustment.
Broad
Scan
SDI
V: Vertical image adjustment.
ZOOM: Zoom mode selection (short push)
FINDER: Zoom finder (long push – blinking LED) : Preview of the actual part of the picture to be
zoomed.
H/V: Horizontal & Vertical (simultaneously) image adjustment.
CENTERING: Image automatic centering.
MENU CONTROL
Allows scrolling thru the different menus.
ENTER: Validates a selected item.
EXIT MENU: Allows to exit from a LCD menu.
PAGE 10
BROAD SCAN (HD/SDI) Chapter 1 : INTRODUCTION (continued)
1-8. BROAD SCAN HD (BHD930) REAR PANEL DESCRIPTION
O / I: AC power switch (O = OFF, I = ON).
POWER: Standard IEC connector (100-250 VAC, 0.5A, 50-60Hz automatic).
RS-232: RS-232 communication port on a DB9 female connector.
IP/LAN: Ethernet communication port on a RJ45 connector (optional).
COMPUTER INPUT & MONITOR
AUDIO IN: Analog stereo audio input on 2x RCA female connector (L = Left, R = Right).
RGB INPUT: Analog computer input on HD15 female connector.
RGB MONITOR OUT: Analog computer output (loop-through) on HD15 female connector.
DVI-D INPUT: Digital computer input on DVI-D female connector.
DVI-D MONITOR OUT: Digital computer output (loop-through) on DVI-D female connector.
ANALOG GENLOCK (Available on BHD930-AG model only).
INPUT: Analog GENLOCK input (Analog HD Black and Black burst signals).
LOOP OUT: GENLOCK output (loop-through).
DIGITAL GENLOCK (Available on BHD930-DG model only).
INPUT: Digital GENLOCK input (SD-SDI & HD-SDI signals).
LOOP OUT: GENLOCK output (loop-through).
VIDEO OUTPUTS
PAL/NTSC: Composite video output (on 1 BNC connector).
LUMA KEY: Luma key video output (on a BNC connector).
FRAME LOCK: Frame lock output (on a BNC connector). This output allows synchronizing external
frame rate such as some graphic card.
S.VIDEO: S.VIDEO output (4-pin mini DIN connector).
R, G, B, S: RGB/S or RGsB video outputs (on 3 or 4 BNC connectors).
Cr, Y, Cb: Component video (SD-YUV & HD-YUV) output (on 3 BNC connectors).
SD/HD-SDI
OUT 1 & 2: 2 SD/HD-SDI outputs (on BNC connectors)
LUMA KEY 1 & 2: 2 SD/HD-SDI luma key outputs (on BNC connectors)
PAGE 11
Chapter 1 : INTRODUCTION (continued) BROAD SCAN (HD/SDI)
1-9. BROAD SCAN SDI (BSD830) REAR PANEL DESCRIPTION
O / I: AC power switch (O = OFF, I = ON).
POWER: Standard IEC connector (100-250 VAC, 0.5A, 50-60Hz automatic).
RS-232: RS-232 communication port on a DB9 female connector.
IP/LAN: Ethernet communication port on a RJ45 connector (optional).
COMPUTER INPUT & MONITOR
AUDIO IN: Analog stereo audio input on 2x RCA female connector (L = Left, R = Right).
RGB INPUT: Analog computer input on HD15 female connector.
RGB MONITOR OUT: Analog computer output (loop-through) on HD15 female connector.
DVI-D INPUT: Digital computer input on DVI-D female connector.
DVI-D MONITOR OUT: Digital computer output (loop-through) on DVI-D female connector.
ANALOG GENLOCK (Available on BSD830-AG model only).
INPUT: Analog GENLOCK input (Black burst signals).
LOOP OUT: GENLOCK output (loop-through).
DIGITAL GENLOCK (Available on BSD830-DG model only).
INPUT: Digital GENLOCK input (SD-SDI signals).
LOOP OUT: GENLOCK output (loop-through).
VIDEO OUTPUTS
PAL/NTSC: Composite video output (on 1 BNC connector).
LUMA KEY: Luma key video output (on a BNC connector).
FRAME LOCK: Frame lock output (on a BNC connector). This output allows synchronizing external
frame rate such as some graphic card.
S.VIDEO: S.VIDEO output (4-pin mini DIN connector).
R, G, B, S: RGB/S or RGsB video outputs (on 3 or 4 BNC connectors).
Cr, Y, Cb: Component video (SD-YUV) output (on 3 BNC connectors).
SD-SDI
OUT 1 & 2: 2 SD-SDI outputs (on BNC connectors).
LUMA KEY 1 & 2: 2 SD-SDI luma key outputs (on BNC connectors).
PAGE 12
BROAD SCAN (HD/SDI) Chapter 1 : INTRODUCTION (continued)
1-10. BROAD SCAN (BSC730) FRONT PANEL DESCRIPTION
R
ANALOG WAY
ON / OFF: Switch ON or OFF the device (Long push).
BLACK: Allows displaying a black screen onto the output.
FREEZE: Freezes the displayed output.
UNDER/OVER: Image mode selection.
ASPECT RATIO: Aspect ratio selection.
1/1: The image and aspect ratio of the source are preserved.
Cropped: The image is resized and the borders are cut to fill full the screen (The aspect ratio is
preserved).
Full Screen: The image is stretched to fill full the screen without cutting the borders (The aspect ratio is
not preserved).
PAN & ZOOM
POS. SIZE: Position or Size mode selection.
H: Horizontal image adjustment.
V: Vertical image adjustment.
ZOOM: Zoom mode selection (short push)
Broad
Scan
FINDER: Zoom finder (long push– blinking LED) : Preview of the actual part of the picture to be
zoomed.
H/V: Horizontal & Vertical (simultaneously) image adjustment.
CENTERING: Image automatic centering.
MENU CONTROL
Allows scrolling thru the different menus.
ENTER: Validates a selected item.
EXIT MENU: Allows to exit from a LCD menu.
PAGE 13
Chapter 1 : INTRODUCTION (continued) BROAD SCAN (HD/SDI)
1-11. BROAD SCAN (BSC730) REAR PANEL DESCRIPTION
O / I: AC power switch (O = OFF, I = ON).
POWER: Standard IEC connector (100-250 VAC, 0.5A, 50-60Hz automatic).
RS-232: RS-232 communication port on a DB9 female connector.
IP/LAN: Ethernet communication port on a RJ45 connector (optional).
COMPUTER INPUT & MONITOR
RGB INPUT: Analog computer input on HD15 female connector.
RGB MONITOR OUT: Analog computer output (loop-through) on HD15 female connector.
DVI-D INPUT: Digital computer input on DVI-D female connector.
DVI-D MONITOR OUT: Digital computer output (loop-through) on DVI-D female connector.
ANALOG GENLOCK
INPUT: Analog GENLOCK input (Black burst signals).
LOOP OUT: GENLOCK output (loop-through).
VIDEO OUTPUTS
PAL/NTSC: Composite video output (on 1 BNC connector).
LUMA KEY: Luma key video output (on a BNC connector).
FRAME LOCK: Frame lock output (on a BNC connector). This output allows synchronizing external
frame rate such as some graphic card.
S.VIDEO: S.VIDEO output (4-pin mini DIN connector).
R, G, B, S: RGB/S or RGsB video outputs (on 3 or 4 BNC connectors).
Cr, Y, Cb: Component video (SD-YUV) output (on 3 BNC connectors).
PAGE 14
Loading...