Analog Devices ADVFC32 b Datasheet

Voltage-to-Frequency and
a
FEATURES High Linearity
0.01% Max at 10 kHz FS0.05% Max at 100 kHz FS0.2% Max at 500 kHz FS
Output TTL/CMOS-Compatible V/F or F/V Conversion 6 Decade Dynamic Range Voltage or Current Input Reliable Monolithic Construction MIL-STD-883-Compliant Versions Available
PRODUCT DESCRIPTION
The industry standard ADVFC32 is a low cost monolithic voltage-to-frequency (V/F) converter or frequency-to-voltage (F/V) converter with good linearity (0.01% max error at 10 kHz) and operating frequency up to 0.5 MHz. In the V/F configuration, positive or negative input voltages or currents can be converted to a proportional frequency using only a few external compo­nents. For F/V conversion, the same components are used with a simple biasing network to accommodate a wide range of input logic levels.
TTL or CMOS compatibility is achieved in the V/F operating mode using an open collector frequency output. The pull-up resistor can be connected to voltages up to 30 volts, or to 15 V or 5 V for conventional CMOS or TTL logic levels. This resis­tor should be chosen to limit current through the open collector output to 8 mA. A larger resistance can be used if driving a high impedance load.
Input offset drift is only 3 ppm of full scale per °C, and full­scale calibration drift is held to a maximum of 100 ppm/°C (ADVFC32BH) due to a low T.C. Zener diode.
The ADVFC32 is available in commercial, industrial, and extended temperature grades. The commercial grade is pack­aged in a 14-lead plastic DIP while the two wider temperature range parts are packaged in hermetically sealed 10-lead cans.
PRODUCT HIGHLIGHTS
1. The ADVFC32 uses a charge balancing circuit technique (see Functional Block Diagram) which is well suited to high accuracy voltage-to-frequency conversion. The full-scale operating frequency is determined by only one precision resistor and capacitor. The tolerance of other support compo­nents (including the integration capacitor) is not critical. Inexpensive ±20% resistors and capacitors can be used with­out affecting linearity or temperature drift.
Frequency-to-Voltage Converter
ADVFC32
PIN CONFIGURATION
(TOP VIEW)
N-14 Package
H-10A Package
2. The ADVFC32 is easily configured to satisfy a wide range of system requirements. Input voltage scaling is set by selecting the input resistor which sets the input current to 0.25 mA at the maximum input voltage.
3. The same components used for V/F conversion can also be used for F/V conversion by adding a simple logic biasing network and reconfiguring the ADVFC32.
4. The ADVFC32 is intended as a pin-for-pin replacement for VFC32 devices from other manufacturers.
5. The ADVFC32 is available in versions compliant with MIL­STD-883. Refer to the Analog Devices Military Products Databook or current ADVFC32/883B data sheet for detailed specifications.
REV. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 2000
ADVFC32–SPECIFICATIONS
(typical @ 25C with VS = 15 V unless otherwise noted.)
ADVFC32K ADVFC32B ADVFC32S
Model Min Typ Max Min Typ Max Min Typ Max Unit
DYNAMIC PERFORMANCE
Full-Scale Frequency Range 0 500 0 500 0 500 kHz Nonlinearity
f f f
Full-Scale Calibration Error
1
= 10 kHz –0.01 ±0.01 –0.01 +0.01 –0.01 +0.01 %
MAX
= 100 kHz –0.05 +0.05 –0.05 +0.05 –0.05 +0.05 %
MAX
= 0.5 MHz –0.20 ±0.05 +0.20 –0.20 ±0.05 +0.20 –0.20 ± 0.05 +0.20 %
MAX
(Adjustable to Zero) ±5 ±5 ±5%
vs. Supply
(Full-Scale Frequency = 100 kHz)
–0.015 +0.015 –0.015 +0.015 –0.015 +0.015
% of FSR%
vs. Temperature
(Full-Scale Frequency = 10 kHz)
±75 –100 +100 +150 +150
ppm/°C
DYNAMIC RESPONSE
Maximum Settling Time for Full Scale
Step Input 1 Pulse of New Frequency Plus 1 µs 1 Pulse of New Frequency Plus 1 µs 1 Pulse of New Frequency Plus 1 µs
Overload Recovery Time 1 Pulse of New Frequency Plus 1 µs 1 Pulse of New Frequency Plus 1 µs 1 Pulse of New Frequency Plus 1 µs
ANALOG INPUT AMPLIFIER
(V/F Conversion)
Current Input Range 0 0.25 0 0.25 0 0.25 mA Voltage Input Range 0 –10 0 –10 0 –10 V
0.25 0.25 0.25 mA
Differential Impedance
300 kΩ||10 pF
3
× R
2 MΩ||10 pF 300 kΩ||10 pF 2 MΩ||10 pF 300 kΩ||10 pF 2 MΩ||10 pF
IN
× R
3
IN
× R
2
3
IN
Common-Mode Impedance 300 MΩ||3 pF 750 MΩ||3 pF 300 MΩ||3 pF 750 MΩ||10 pF 300 MΩ||3 pF 750 MΩ||10 pF Input Bias Current
Noninverting Input 40 250 40 250 40 250 nA Inverting Input –100 ±8 +100 –100 ±8 +100 –100 ± 8 +100 nA
Input Offset Voltage
(Trimmable to Zero) vs. Temperature (T
Safe Input Voltage ±V
MIN
2, 3
MAX
S
±V
S
±V
S
to T
444mV
)30 30 30 µV/°C
COMPARATOR (F/V Conversion)
Logic “0” Level –V Logic “1” Level 1 +V Pulse Width Range
4
S
0.1 0.15/f
Input Impedance 50 kΩ||10 pF 250 k 50 kΩ||10 pF 250 k 50 kΩ||10 pF 250 k
–0.6 –V
S
1+V
0.1 0.15/f
MAX
S
–0.6 –V
1+V
S
0.1
MAX
S
–0.6 V
S
0.15/f
MAX
V µs
OPEN COLLECTOR OUTPUT
(V/F Conversion)
Output Voltage in Logic “0”
I
= 8 mA 0.4 0.4 0.4 V
SINK
Output Leakage Current in Logic “1”
111µA
Voltage Range 0 30 0 30 0 30 V Fall Times (Load = 500 pF and
I
= 5 mA) 400 400 400 ns
SINK
AMPLIFIER OUTPUT (F/V Conversion)
Voltage Range (0 mA≤IO≤7 mA) 0 10 0 10 0 10 V Source Current (0≤V Capacitive Load (Without Oscillation) 100 100 100 pF
7 V) 10 10 10 mA
O
Closed Loop Output Impedance 1 1 1
POWER SUPPLY
Rated Voltage ±15 ±15 ±15 V Voltage Range ± 9 ±18 ± 9 ± 18 ±9 ± 18 V Quiescent Current 6 8 6 8 6 8 mA
TEMPERATURE RANGE
Specified Range 0 +70 –25 +85 –55 +125 °C Operating Range –25 +85 –55 +125 –55 +125 °C Storage –25 +85 –65 +150 –65 +150 °C
PACKAGE OPTIONS
Plastic DIP (N-14) ADVFC32KN TO–100 (H-10A)
NOTES
1
Nonlinearity defined as deviation from a straight line from zero to full scale, expressed as a percentage of full scale.
2
See Figure 3.
3
See Figure 1.
4
f
expressed in units of MHz.
MAX
Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All min and max specifications are guaranteed, although only those shown in boldface are tested on all production units.
Specifications subject to change without notice.
ADVFC32BH ADVFC32SH
–2–
REV. B
Loading...
+ 4 hidden pages