Analog Devices ADV7172 3 b Datasheet

Digital PAL/NTSC Video Encoder

with Six DACs (10 Bits), Color Control

a

and Enhanced Power Management

ADV7172/ADV7173*

FEATURES

1

BT601/656 YCrCb to PAL/NTSC Video Encoder

ITU-R
Six High Quality 10-Bit Video DACs
SSAF™ (Super Sub-Alias Filter)
Advanced Power Management Features

PC’98-Compliant (TV Detect with Polling and Auto

Shutdown to Save On Power Consumption)
Low Power DAC Mode
Individual DAC ON/OFF Control
Variable DAC Output Current (5 mA–36 mA)
Ultralow Sleep Mode Current

Hue, Brightness, Contrast and Saturation Controls
CGMS (Copy Generation Management System)
WSS (Wide Screen Signalling)
NTSC-M, PAL-M/N, PAL-B/D/G/H/I, PAL-60
YUV Betacam, MII and SMPTE/EBU N10 Output Levels
Single 27 MHz Clock Required (2 Oversampling)
80 dB Video SNR
32-Bit Direct Digital Synthesizer for Color Subcarrier
Multistandard Video Output Support:

Composite (CVBS)
Component S-Video (Y/C)
Component YUV
EuroSCART RGB
Component YUV + CHROMA + LUMA + CVBS
EuroSCART Output RGB + CHROMA + LUMA + CVBS

Programmable Clamping Output Signal
Advanced Programmable Power-On Reset Sequencing
Video Input Data Port Supports:

CCIR-656 4:2:2 8-Bit Parallel Input Format
SMPTE 170M NTSC-Compatible Composite Video
ITU-R BT.470 PAL-Compatible Composite Video

Luma Sharpness Control
Programmable Luma Filters (Low-Pass [PAL/NTSC],

Notch [PAL/NTSC], Extended [SSAF], CIF and QCIF)

Programmable Chroma Filters (Low-Pass [0.65 MHz,

1.0 MHz, 1.2 MHz and 2.0 MHz], CIF and QCIF)

Programmable VBI (Vertical Blanking Interval)
Programmable Subcarrier Frequency and Phase
Programmable LUMA Delay
CCIR and Square Pixel Operation
Integrated Subcarrier Locking to External Video Source

NOTES
*This device is protected by U.S. Patent Numbers 4,631,603, 4,577,216, 4,819,098 and other intellectual property rights.

1

ITU-R and CCIR are used interchangeably in this document (ITU-R has replaced CCIR recommendations).

2

The Macrovision anticopy process is licensed for noncommercial home use only, which is its sole intended use in the device. Please contact sales office for latest

Macrovision version available.
SSAF is a trademark of Analog Devices, Inc.
I2C is a registered trademark of Philips Corporation.

Color Signal Control/Burst Signal Control
Interlaced/Noninterlaced Operation
Complete On-Chip Video Timing Generator
Programmable Multimode Master/Slave Operation
Macrovision Antitaping Rev 7.1 (ADV7172 Only)
Closed Captioning Support
Teletext Insertion Port (PAL-WST)
On-Board Color Bar Generation
On-Board Voltage Reference
2-Wire Serial MPU Interface (I
Single Supply 5 V or 3.3 V Operation
Small 48-Lead LQFP Package

APPLICATIONS
High Performance DVD Playback Systems, Portable

Video Equipment including Digital Still Cameras and
Laptop PCs, Video Games, PC Video/Multimedia and
Digital Satellite/Cable Systems (Set-Top Boxes/IRD)

GENERAL DESCRIPTION

The ADV7172/ADV7173 is an integrated Digital Video
Encoder that converts digital CCIR-601 4:2:2 8-bit component
video data into a standard analog baseband television signal
compatible with worldwide standards.

There are six DACs available on the ADV7172/ADV7173. In
addition to the Composite output signal there is the facility to
output S-VHS Y/C Video, RGB Video and YUV Video.

The on-board SSAF (Super Sub-Alias Filter), with extended
luminance frequency response and sharp stopband attenuation,
enables studio quality video playback on modern TVs, giving
optimal horizontal line resolution. An additional sharpness control
feature allows extra luminance boost on the frequency response.

An advanced power management circuit enables optimal control
of power consumption in both normal operating modes and
power down or sleep modes. A PC’98-Compliant autodetect
feature has been added to allow the user to determine whether
or not the DACs are correctly terminated. If not, the ADV7172/
ADV7173 flags that they are not connected through the Status
bit and provides the option of automatically powering them
down, thereby reducing power consumption.

The ADV7172/ADV7173 also supports both PAL and NTSC
square pixel operation. The parts also incorporate WSS and
CGMS-A data control generation.

2C®

-Compatible and Fast I2C)

2

REV. B

Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] www.analog.com
Fax: [phone] © Analog Devices, Inc., 2001

ADV7172/ADV7173

PAL

CLOCK CSO_HSO VSO

NTSC

FUNCTIONAL BLOCK DIAGRAM

CLAMP

SCLOCK SDATA

ALSB

HSYNC

FIELD/

VSYNC
BLANK

RESET

TTX

TTXREQ

V

COLOR

DATA

VIDEO TIMING

GENERATOR

TELETEXT

INSERTION BLOCK

AA

8

P0

4:2:2 TO

INTER-

POLATOR

P7

4:4:4

8

8

YCrCb

TO

YUV

MATRIX

Y

U

V

BRIGHTNESS AND

CONTRAST CONTROL

8

8

8

ADD SYNC

INTERPOLATOR

SATURATION CONTROL

ADD BURST

INTERPOLATOR

ADV7172/ADV7173

I2C MPU PORT

+

+

+

+

REAL-TIME

CONTROL CIRCUIT

SCRESET/RTC

PROGRAMMABLE

10

SHARPNESS

10

PROGRAMMABLE

CHROMA

10

The ADV7172/ADV7173 is designed with four color controls
(hue, contrast, brightness and saturation). All YUV formats
(SMPTE/EBU N10, MII and Betacam) are supported in both
PAL and NTSC.

The output video frames are synchronized with the incoming data
Timing Reference Codes. Optionally the encoder accepts (and can
generate) HSYNC, VSYNC, and FIELD timing signals. These
timing signals can be adjusted to change pulsewidth and position
while the part is in the master mode. The Encoder requires a
single two times pixel rate (27 MHz) clock for standard opera­tion. Alternatively the Encoder requires a 24.5454 MHz clock
for NTSC or 29.5 MHz clock for PAL square pixel mode
operation. All internal timing is generated on-chip.

HSO/CSO and VSO TTL outputs, synchronous to the analog
output video, are also available. A programmable CLAMP out­put signal is also available to enable clamping in either the front
or back porch of the video signal.

A separate teletext port enables the user to directly input teletext
data during the vertical blanking interval.

The ADV7172/ADV7173 modes are set up over a 2-wire serial
bidirectional port (I

2

C-Compatible) with two slave addresses.
Functionally the ADV7173 and ADV7172 are the same with the
exception that the ADV7172 can output the Macrovision anti­copy algorithm.

The ADV7172/ADV7173 is packaged in a 48-lead LQFP pack­age (1.4 mm thickness).

DATA PATH DESCRIPTION

For PAL B, D, G, H, I, M, N, and NTSC M, N modes, YCrCb
4:2:2 Data is input via the CCIR-656-Compatible Pixel Port at a
27 MHz Data Rate. The Pixel Data is demultiplexed to form
three data paths. Y typically has a range of 16 to 235, Cr, and
Cb typically have a range of 128 ± 112; however, it is possible to

M

10

10

U

L
T

I
P
L
E
X
E

R

M
U
L
T

I

P
L
E
X
E
R

10-BIT

10

10-BIT

10

10-BIT

DAC

CONTROL

BLOCK

10

10-BIT

10

10-BIT

10

10-BIT

DAC

CONTROL

BLOCK

DAC

DAC

DAC

DAC

DAC

DAC

DAC A

DAC B

DAC C

V

REF

R

SET2

COMP2

DAC E

DAC F

DAC D

R

SET1

COMP1

LUMA

FILTER

+

FILTER

FILTER

GND

YUV TO

RBG

MATRIX

+

YUV

LEVEL

CONTROL

BLOCK

MODULATOR

+

HUE

CONTROL

10 10

SIN/COS

DDS BLOCK

10

10

10

10

10

input data from 1 to 254 on both Y, Cb, and Cr. The ADV7172/
ADV7173 supports PAL (B, D, G, H, I, N, M) and NTSC
(with and without pedestal) standards. The Y data is then
manipulated by being scaled for contrast control and a setup
level is added for brightness control. The Cr, Cb data is also
scaled and saturation control is added. The appropriate Sync,
Blank and Burst levels are then added to the YCrCb data. Mac­rovision AntiTaping (ADV7172 only), Closed-Captioning and
Teletext levels are also added to Y, and the resultant data is
interpolated to a rate of 27 MHz. The interpolated data is fil­tered and scaled by three digital FIR Filters.

The U and V Signals are modulated by the appropriate sub­carrier sine/cosine phases and a phase offset may be added onto
the color subcarrier during active video to allow hue adjustment.
The resulting U and V signals are then added together to make
up the chrominance signal. The luma (Y) signal can be delayed
1–3 luma cycles (each cycle is 74 ns) with respect to the chroma
signal. The luma and chroma signals are then added together to
make up the composite video signal. All edges are slew rate limited.

The YCrCb data is also used to generate RGB data with appro­priate Sync and Blank levels.

There are six DACs on the ADV7172/ADV7173. Three of these
DACs are capable of providing 34.66 mA of current. The other
three DACs provide 8.66 mA each.

The six l0-bit DACs can be used to output:

1. Composite Video + RGB Video + LUMA + CHROMA.

2. Composite Video + YUV Video + LUMA + CHROMA.

Alternatively, each DAC can be individually powered off if not
required. A complete description of DAC output configurations
is given in Appendix 8.

Video output levels are illustrated in Appendix 6.

–2–

REV. B

SPECIFICATIONS

(VAA = 5 V  5%1, V

5 V SPECIFICATIONS

unless otherwise noted.)

Parameter Test Conditions

= 1.235 V, R

REF

SET1,2

= 600  unless otherwise noted. All specifications T

1

Min Typ Max Unit

ADV7172/ADV7173

MIN

STATIC PERFORMANCE

Resolution (Each DAC) 10 Bits
Accuracy (Each DAC)
Integral Nonlinearity
Differential Nonlinearity

3

3

Guaranteed Monotonic ± 1.0 LSB

± 1.0 LSB

DIGITAL INPUTS

Input High Voltage, V
Input Low Voltage, V
Input Current, I
Input Capacitance, C

INL

IN

IN

INH

VIN = 0.4 V or 2.4 V ± 1 µA

2V

0.8 V

10 pF

DIGITAL OUTPUTS

I

Output High Voltage, V
Output Low Voltage, V

OL

OH

= 400 µA 2.4 V

SOURCE

I

= 3.2 mA 0.4 V

SINK

Three-State Leakage Current 10 µA
Three-State Output Capacitance 10 pF

ANALOG OUTPUTS

Output Current (DACs A, B, C)
Output Current (DACs A, B, C)
Output Current (DACs D, E, F)
Output Current (DACs D, E, F)
DAC-to-DAC Matching (DACs A, B, C)
DAC-to-DAC Matching (DACs D, E, F)
Output Compliance, V
Output Impedance, R
Output Capacitance, C

OC

OUT

OUT

4

5

6

5

R

= 150 Ω, RL = 37.5 Ω 33 34.7 37 mA

SET1

R

= 1041 Ω, RL = 262.5 Ω 5mA

SET1

R

= 600 Ω, RL = 150 Ω 8.25 8.66 9.25 mA

SET2

R

= 1041 Ω, RL = 262.5 Ω 5mA

SET2

7

7

1 4.0 %
1 4.0 %

0 1.4 V

30 kΩ

I

= 0 mA 30 pF

OUT

VOLTAGE REFERENCE

Reference Range, V

REF

I

VREFOUT

= 20 µA 1.112 1.235 1.359 V

POWER REQUIREMENTS

V

AA

Normal Power Mode

I

DAC

I

DAC

I

CCT

Low Power Mode

I

DAC

I

DAC

I

CCT

Sleep Mode

I

DAC

I

CCT

(max)
(min)

10

(max)
(min)

10

12

13

8, 9

8, 9

11

11

R

= 600 Ω 59 65 mA

SET1,2

R

= 1041 Ω 30 mA

SET1,2

R

= 150 Ω 64 mA

SET1

4.75 5.0 5.25 V

78 90 mA

15 mA
78 90 mA

0.1 µA

0.1 µA

Power Supply Rejection Ratio COMP = 0.1 µF 0.01 0.5 %/%

NOTES

1

The max/min specifications are guaranteed over this range. The max/min values are typical over 4.75 V to 5.25 V.

2

Temperature range T

3

Characterized by design.

4

Full drive into 75 Ω doubly terminated load.

5

Minimum drive current (used with buffered/scaled output load).

6

Full drive into 150 Ω load.

7

Specification guaranteed by characterization.

8

I

is the total current (“min” corresponds to 5 mA output per DAC, “max” corresponds to 8.66 mA output per DAC ) to drive DACs A, B, C, D, E, F. Turning off

DAC

individual DACs reduces I

9

All six DACs on (DAC A, B, C, D, E, F).

10

I

(Circuit Current) is the continuous current required to drive the device.

CCT

11

Only large DACs (DACs A, B, C) on per low power mode.

12

Total DAC current in Sleep Mode.

13

Total continuous current during Sleep Mode.

Specifications subject to change without notice.

to T

MIN

: 0°C to 70°C.

MAX

correspondingly, also DACs A, B, C can be configured to output a max current of 37 mA but DAC D, E, F must be turned off.

DAC

to T

MAX

2

REV. B

–3–

ADV7172/ADV7173–SPECIFICATIONS

(VAA = 3.0 V–3.6 V1, V

3.3 V SPECIFICATIONS

unless otherwise noted.)

Parameter Test Conditions

STATIC PERFORMANCE

3

Resolution (Each DAC) 10 Bits
Accuracy (Each DAC)
Integral Nonlinearity 1.0 LSB
Differential Nonlinearity Guaranteed Monotonic 1.0 LSB

DIGITAL INPUTS

Input High Voltage, V
Input Low Voltage, V
Input Current, I
Input Capacitance, C

DIGITAL OUTPUTS

Output High Voltage, V
Output Low Voltage, V

3

INH

INL

IN

IN

3

OH

OL

Three-State Leakage Current 10 µA
Three-State Output Capacitance 10 pF

ANALOG OUTPUTS

Output Current (DACs A, B, C)
Output Current (DACs A, B, C)
Output Current (DACs D, E, F)
Output Current (DACs D, E, F)
DAC-to-DAC Matching (DACs A, B, C)
DAC-to-DAC Matching (DACs D, E, F)
Output Compliance, V
Output Impedance, R
Output Capacitance, C

POWER REQUIREMENTS

V

AA

Normal Power Mode

(max)

I

DAC

I

(min)

DAC

10

I

CCT

Sleep Mode

11

I

DAC

12

I

CCT

3

4

5

6

5

3

3

OC

OUT

OUT

3, 7

8, 9

8

Power Supply Rejection Ratio COMP = 0.1 µF 0.01 %/%

NOTES

1

The max/min specifications are guaranteed over this range. The max/min values are typical over 3.0 V to 3.6 V.

2

Temperature range T

3

Guaranteed by characterization.

4

Full drive into 75 Ω doubly terminated load.

5

Minimum drive current (used with buffered/scaled output load).

6

Full Drive into 150 Ω load.

7

Power measurements are taken with Clock Frequency = 27 MHz. Max TJ = 110°C.

8

I

is the total current (“min” corresponds to 5 mA output per DAC, “max” corresponds to 8.66 mA output per DAC ) to drive DACs A, B, C, D, E, F. Turning off

DAC

individual DACs reduces I

9

DACs A, B, C can output 35 mA typically at 3.3 V (R

RL = 75 Ω).

10

I

(Circuit Current) is the continuous current required to drive the device.

CCT

11

Total DAC current in Sleep Mode.

12

Total continuous current during Sleep Mode.

Specifications subject to change without notice.

to T

MIN

: 0°C to 70°C.

MAX

correspondingly, also DACs A, B, C can be configured to output a max current of 37 mA.

DAC

= 150 Ω and RL = 37.5 Ω), optimum performance obtained at 18 mA DAC Current (R

SET

= 1.235 V, R

REF

= 600  unless otherwise noted. All specifications T

SET1,2

1

Min Typ Max Unit

2V

0.8 V

VIN = 0.4 V or 2.4 V ± 1 µA

10 pF

I
I

R
R
R
R

= 400 µA 2.4 V

SOURCE

= 3.2 mA 0.4 V

SINK

= 150 Ω, RL = 37.5 Ω 34.7 mA

SET1

= 1041 Ω, RL = 262.5 Ω 5mA

SET1

= 600 Ω, RL = 150 Ω 8.66 mA

SET2

= 1041 Ω, RL = 262.5 Ω 5mA

SET2

1 4.0 %
1 4.0 %

1.4 V

30 kΩ

I

= 0 mA 30 pF

OUT

3.0 3.3 3.6 V

R

= 600 Ω 58 65 mA

SET1,2

R

= 1041 Ω 30 mA

SET1,2

40 mA

0.1 µA

0.1 µA

= 300 Ω and

SET

MIN

to T

MAX

2

–4–

REV. B

ADV7172/ADV7173

(VAA = 5 V  5%1, V

5 V DYNAMIC SPECIFICATIONS

Parameter Conditions

3, 4

3, 4

3, 4

3, 4

3, 4

MIN

3, 4

3, 4

to T

3, 4

3, 4

3, 4

3, 4

3, 4

3, 4

: 0°C to 70°C.

MAX

3, 4

Differential Gain
Differential Phase
Differential Gain
Differential Phase

3, 4

(Pedestal) RMS 75 dB rms

SNR

3, 4

(Pedestal) Peak Periodic 66 dB p-p

SNR

3, 4

SNR

(Ramp) RMS 60 dB rms

3, 4

(Ramp) Peak Periodic 58 dB p-p

SNR
Hue Accuracy
Color Saturation Accuracy
Chroma Nonlinear Gain
Chroma Nonlinear Phase
Chroma/Luma Intermod
Chroma/Luma Gain Inequality
Chroma/Luma Delay Inequality
Luminance Nonlinearity
Chroma AM Noise
Chroma PM Noise

NOTES

1

The max/min specifications are guaranteed over this range. The max/min values are typical over 4.75 V to 5.25 V range.

2

Temperature range T

3

These specifications are for the low-pass filter only and guaranteed by design.

4

Guaranteed by characterization.

Specifications subject to change without notice.

specifications T

1

Normal Power Mode 0.3 0.7 %
Normal Power Mode 0.4 0.7 Degrees
Lower Power Mode 0.5 1.0 %
Lower Power Mode 2.0 3.0 Degrees

Referenced to 40 IRE 1.2 ± %

MIN

REF

to T

= 1.235 V, R

2

unless otherwise noted.)

MAX

= 600  unless otherwise noted. All

SET1,2

Min Typ Max Unit

79 82 dB
79 80 dB

0.7 Degrees

0.9 %

0.3 0.5 ± Degrees

0.2 0.4 ± %

1.0 ± %

0.5 ns

1.0 1.7 ± %

(VAA = 3.0 V–3.6 V1, V

3.3 V DYNAMIC SPECIFICATIONS

Parameter Conditions

Differential Gain
Differential Phase
Differential Gain
Differential Phase

3

SNR

(Pedestal) RMS 75 dB rms

3

SNR

(Pedestal) Peak Periodic 70 dB p-p

3

(Ramp) RMS 60 dB rms

SNR

3

SNR

(Ramp) Peak Periodic 58 dB p-p
Hue Accuracy
Color Saturation Accuracy
Luminance Nonlinearity
Chroma AM Noise
Chroma PM Noise
Chroma Nonlinear Gain
Chroma Nonlinear Phase
Chroma/Luma Intermod

NOTES

1

The max/min specifications are guaranteed over this range. The max/min values are typical over 3.0 V to 3.6 V.

2

Temperature range T

3

Guaranteed by characterization.

4

These specifications are for the low-pass filter only and guaranteed by design.

Specifications subject to change without notice.

3

3

3

3

3

3

3

3

3

3, 4

3, 4

3, 4

to T

MIN

: 0°C to 70°C.

MAX

specifications T

1

Normal Power Mode 0.6 %
Normal Power Mode 0.5 Degrees
Lower Power Mode 1.0 %
Lower Power Mode 0.5 Degrees

Referenced to 40 IRE 1.2 ± %

MIN

to T

= 1.235 V, R

REF

2

unless otherwise noted.)

MAX

SET1,2

Min Typ Max Unit

= 600  unless otherwise noted. All

1.0 Degrees

1.0 %

1.1 ± %
83 dB
79 dB

0.3 ± Degrees

0.2 ± %

REV. B

–5–

ADV7172/ADV7173

(VAA = 5 V  5%1, V

5 V TIMING SPECIFICATIONS

2

to T

unless otherwise noted.)

MAX

Parameter Conditions Min Typ Max Unit

MPU PORT

3, 4

SCLOCK Frequency 0 400 kHz
SCLOCK High Pulsewidth, t
SCLOCK Low Pulsewidth, t
Hold Time (Start Condition), t
Setup Time (Start Condition), t
Data Setup Time, t

5

SDATA, SCLOCK Rise Time, t
SDATA, SCLOCK Fall Time, t
Setup Time (Stop Condition), t

ANALOG OUTPUTS

3, 5

1

2

After this period the 1st clock is generated 0.6 µs

3

relevant for repeated Start Condition. 0.6 µs

4

6

7

8

Analog Output Delay 7ns
DAC Analog Output Skew 0 ns

CLOCK CONTROL AND
PIXEL PORT

f

CLOCK

Clock High Time, t
Clock Low Time, t
Data Setup Time, t
Data Hold Time, t
Control Setup Time, t
Control Hold Time, t
Digital Output Access Time, t
Digital Output Hold Time, t
Pipeline Delay, t

TELETEXT PORT

Digital Output Access Time, t
Data Setup Time, t
Data Hold Time, t

RESET CONTROL

5, 6

9

10

11

12

11

12

13

14

15

3, 7

16

17

18

3

RESET Low Time 3ns

NOTES

1

The max/min specifications are guaranteed over this range. The max/min values are typical over 4.75 V to 5.25 V.

2

Temperature range T

3

TTL input values are 0 to 3 volts, with input rise/fall times ≤ 3 ns, measured between the 10% and 90% points. Timing reference points at 50% for inputs and

outputs. Analog output load ≤ 10 pF.

4

Guaranteed by characterization.

5

Output delay measured from the 50% point of the rising edge of CLOCK to the 50% point of full-scale transition.

6

Pixel Port consists of the following:

Pixel Inputs: P7–P0
Pixel Controls: HSYNC, FIELD/VSYNC, BLANK, VSO, CSO_HSO, CLAMP
Clock Input: CLOCK

7

Teletext Port consists of the following:

Teletext Output: TTXREQ
Teletext Input: TTX

Specifications subject to change without notice.

MIN

to T

: 0°C to 70°C.

MAX

= 1.235 V, R

REF

= 600  unless otherwise noted. All specifications T

SET1

0.6 µs

1.3 µs

100 ns

300 ns
300 ns

0.6 µs

27 MHz
8ns
8ns

4.0 ns

5.0 ns
4ns
3ns

15 24 ns

10 ns

37 Clock Cycles

20 ns

2ns

6ns

MIN

–6–

REV. B

ADV7172/ADV7173

to T

MAX

2

unless

3.3 V TIMING SPECIFICATIONS

(VAA = 3.0 V–3.6 V1, V
otherwise noted.)

= 1.235 V, R

REF

= 600 . All specifications T

SET1,2

MIN

Parameter Conditions Min Typ Max Unit

MPU PORT

3, 4

SCLOCK Frequency 0 400 kHz
SCLOCK High Pulsewidth, t
SCLOCK Low Pulsewidth, t
Hold Time (Start Condition), t
Setup Time (Start Condition), t
Data Setup Time, t

5

SDATA, SCLOCK Rise Time, t
SDATA, SCLOCK Fall Time, t
Setup Time (Stop Condition), t

ANALOG OUTPUTS

3, 5

1

2

After this period the 1st clock is generated 0.6 µs

3

relevant for repeated Start Condition. 0.6 µs

4

6

7

8

0.6 µs

1.3 µs

100 ns

300 ns
300 ns

0.6 µs

Analog Output Delay 7ns
DAC Analog Output Skew 0 ns

CLOCK CONTROL AND
PIXEL PORT

f

CLOCK

Clock High Time, t
Clock Low Time, t
Data Setup Time, t
Data Hold Time, t
Control Setup Time, t
Control Hold Time, t
Digital Output Access Time, t
Digital Output Hold Time, t
Pipeline Delay, t

TELETEXT PORT

Digital Output Access Time, t
Data Setup Time, t
Data Hold Time, t

RESET CONTROL

4, 5, 6

15

9

10

11

12

3, 4, 7

17

18

3, 4

27 MHz
8ns
8ns

4.0 ns
5ns

11

12

13

14

5ns
3ns

20 ns

12 ns

37 Clock Cycles

16

23 ns

2ns

6ns

RESET Low Time 3ns

NOTES

1

The max/min specifications are guaranteed over this range. The max/min values are typical over 3.0 V to 3.6 V.

2

Temperature range T

3

TTL input values are 0 to 3 volts, with input rise/fall times ≤ 3 ns, measured between the 10% and 90% points. Timing reference points at 50% for inputs and
outputs. Analog output load ≤ 10 pF.

4

Guaranteed by characterization.

5

Output delay measured from the 50% point of the rising edge of CLOCK to the 50% point of full-scale transition.

6

Pixel Port consists of the following:
Pixel Inputs: P7–P0
Pixel Controls: HSYNC, FIELD/VSYNC, BLANK, VSO, CSO_HSO, CLAMP
Clock Input: CLOCK

7

Teletext Port consists of the following:
Teletext Output: TTXREQ
Teletext Input: TTX

Specifications subject to change without notice.

MIN

to T

: 0°C to 70°C.

MAX

REV. B

–7–

ADV7172/ADV7173

SDATA

SCLOCK

CONTROL

I/PS

CLOCK

HSYNC,

FIELD/VSYNC,

BLANK

t

t

3

t

6

t

2

5

t

1

t

7

Figure 1. MPU Port Timing Diagram

t

t

9

10

t

12

t

3

t

4 t

8

CONTROL

O/PS

PIXEL INPUT

DATA

HSYNC,

FIELD/VSYNC,

BLANK,

CSO_HSO,

VSO, CLAMP

Cb Y Cr Y Cb Y

t

11

t

13

t

14

Figure 2. Pixel and Control Data Timing Diagram

TTXREQ

t

16

CLOCK

t

17

TTX

t

18

4 CLOCK

CYCLES

4 CLOCK

CYCLES

4 CLOCK

CYCLES

3 CLOCK

CYCLES

4 CLOCK

CYCLES

Figure 3. Teletext Timing Diagram

DAC Average Current Consumption

DAC D, E, F: The average current consumed by each DAC is the DAC output current as determined by R

SET2/VREF

DAC A, B, C: In normal power mode the average current consumed by each DAC is the DAC output current as determined by R

(see Appendix 8).

SET1

(see Appendix 8).

In Low Power Mode the average current consumed by each DAC is approximately half the DAC output current as determined by R

SET1.

Consult AN-551 for detailed information on ADV7172/ADV7173 power management.

–8–

REV. B

ADV7172/ADV7173

WARNING!

ESD SENSITIVE DEVICE

ABSOLUTE MAXIMUM RATINGS

1

VAA to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V

Voltage on Any Digital Input Pin . GND – 0.5 V to V
Storage Temperature (T
Junction Temperature (T

Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . . . 260°C

Analog Outputs to GND

NOTES

1

Stresses above those listed under Absolute Maximum Ratings may cause permanent

damage to the device. This is a stress rating only; functional operation of the device
at these or any other conditions above those listed in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.

2

Analog output short circuit to any power supply or common can be of an

indefinite duration.

) . . . . . . . . . . . . . . –65°C to +150°C

S

) . . . . . . . . . . . . . . . . . . . . . . 150°C

J

2

. . . . . . . . . . . GND – 0.5 V to V

+ 0.5 V

AA

AA

PIN CONFIGURATION

NTSC

SET1

R

SCRESET/RTC

TTXREQ

SET2

R

SDATA

COMP2

REF

V

36

35

34

33

32

31

30

29

28

27

26

25

DAC F

COMP1

DAC A

V

AA

DAC B

V

AA

GND

V

AA

DAC C

DAC D

V

AA

GND

DAC E

CSO

V

HSO

V

GND

AA

CLOCK

GND

RESET

V

48 47 46 45 44 39 38 3743 42 41 40

1

AA

2

P0

3

P1

4

P2

5

P3

6

P4

7

P5

8

P6

9

P7

10

11

AA

12

13 14 15 16 17 18 19 20 21 22 23 24

VSO

PIN 1
IDENTIFIER

ADV7172/ADV7173

TOP VIEW

(Not to Scale)

GND

HSYNC

FIELD/VSYNC

ALSB

BLANK

PAL

GND

CLAMP

TTX

AA

V

SCLOCK

PACKAGE THERMAL PERFORMANCE

The 48-lead LQFP package is used for this device. The junc­tion-to-ambient (θ

) thermal resistance in still air on a four

JA

layer PCB is 54.6°C/W. The junction-to-case thermal resistance

) is 16.7°C.

(θ

JC

To reduce power consumption when using this part the user is
advised to run the part on a 3.3 V supply, turn off any unused
DACs. However, if 5 V operation is required the user can enable
Low Power mode by setting MR16 to a Logic 1. Another alter­native way to further reduce power is to use external buffers that
dramatically reduce the DAC currents, the current can be low­ered to as low as 5 mA (see AN-551 and Appendix 8 for more
details) from a nominal value of 36 mA.

The user must at all times stay below the maximum junction
temperature of 110°C. The following equation shows how to
calculate this junction temperature:

J

unction Temperature = [VAA (I

DAC

+ I

CCT

) × θJA ] 70°C

where

= 10 mA + (sum of the average currents consumed by each

I

DAC

powered-on DAC).

ORDERING GUIDE

Temperature Package Package

Model Range Description Option

ADV7172KST 0°C to 70°C Plastic Thin ST-48

Quad Flatpack

ADV7173KST 0°C to 70°C Plastic Thin ST-48

Quad Flatpack

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the ADV7172/ADV7173 features proprietary ESD protection circuitry, permanent
damage may occur on devices subjected to high-energy electrostatic discharges. Therefore,
proper ESD precautions are recommended to avoid performance degradation or loss of
functionality.

REV. B

–9–

ADV7172/ADV7173

PIN FUNCTION DESCRIPTION

Mnemonic Input/Output Function

P7–P0 I 8-Bit 4:2:2 Multiplexed YCrCb Pixel Port (P7–P0) P0 represents the LSB.
CLOCK I TTL Clock Input. Requires a stable 27 MHz reference clock for standard operation. Alter-

natively, a 24.5454 MHz (NTSC) or 29.5 MHz (PAL) can be used for square pixel operation.

HSYNC I/O HSYNC (Modes 1 and 2) Control Signal. This pin may be configured to output (Master

Mode) or as an input and accept (Slave Mode) Sync signals.

FIELD/VSYNC I/O Dual Function FIELD (Mode 1) and VSYNC (Mode 2) Control Signal. This pin may be

configured to output (Master Mode) or as an input (Slave Mode) and accept these
control signals.

BLANK I/O Video Blanking Control Signal. The pixel inputs are ignored when this is Logic Level “0.”

This signal is optional.

SCRESET/RTC I This pin can be configured as an input by setting MR42 and MR41 of Mode Register 4. It

can be configured as a subcarrier reset pin, in which case a low-to-high transition on this
pin will reset the subcarrier phase to Field 0. Alternatively it may be configured as a Real­Time Control (RTC) Input.

V

REF

R

SET1

R

SET2

COMP1 O Compensation Pin for DACs A, B, and C. Connect a 0.1 µF Capacitor from COMP to

COMP2 O Compensation Pin for DACs D, E, and F. Connect a 0.1 µF Capacitor from COMP to V
DAC A O GREEN/Composite/Y Analog Output. This DAC is capable of providing 34.66 mA output.
DAC B O BLUE/S-Video Y/U Analog Output. This DAC is capable of providing 34.66 mA output.
DAC C O RED/S-Video C/V Analog Output. This DAC is capable of providing 34.66 mA output.
DAC D O GREEN/Composite/Y Analog Output. This DAC is capable of providing 8.66 mA output.
DAC E O BLUE/S-Video Y/U Analog Output. This DAC is capable of providing 8.66 mA output.
DAC F O RED/S-Video C/V Analog Output. This DAC is capable of providing 8.66 mA output.
SCLOCK I MPU Port Serial Interface Clock Input.
SDATA I/O MPU Port Serial Data Input/Output.
CLAMP O TTL Output Signal to external circuitry to enable clamping of all video signals.
PAL_NTSC I Input signal to select PAL or NTSC mode of operation, pin set to Logic “1” selects PAL.

VSO O VSO TTL Output Sync Signal.
CSO_HSO O Dual Function CSO or HSO TTL Output Sync Signal.

ALSB I TTL Address Input. This signal sets up the LSB of the MPU address.
RESET I The input resets the on-chip timing generator and sets the ADV7172/ADV7173 into

TTX I Teletext Data Input Pin.
TTXREQ O Teletext Data Request output signal used to control teletext data transfer.
V

AA

GND G Ground Pin.

I/O Voltage Reference Input for DACs or Voltage Reference Output (1.235 V).
I A 150 Ω resistor connected from this pin to GND is used to control full-scale amplitudes of

the Video Signals from DACs A, B, and C (the “large” DACs).

I A 600 Ω resistor connected from this pin to GND is used to control full-scale amplitudes of

the Video Signals from DACs D, E, and F (the “small” DACs).

. For Optimum Dynamic Performance in Low Power Mode, the value of the

V

AA

COMP1 capacitor can be lowered to as low as 2.2 nF.

.

AA

default mode. This is NTSC operation, Timing Slave Mode 0, DACs A, B, and C powered
OFF, DACs D, E, and F powered ON, Composite and S-Video out.

P Power Supply (3 V to 5 V).

–10–

REV. B

(continued from page 2)

INTERNAL FILTER RESPONSE

The Y Filter supports several different frequency responses,
including two low-pass responses, two notch responses, an
Extended (SSAF) response with or without gain boost/attenuation,
a CIF response and a QCIF response. The UV Filter supports
several different frequency responses, including four low-pass
responses, a CIF response and a QCIF response. These can be
seen in Figures 4 to 18.

ADV7172/ADV7173

In Extended Mode there is the option of twelve responses
in the range from –4 dB to +4 dB. The desired response can
be chosen by the user by programming the correct value via

2

C. The variation of frequency responses can be seen in

the I
Figures 19 to 21.

–10

–20

FILTER TYPE FILTER SELECTION

MR04

MR03

0

LOW-PASS (NTSC)
LOW-PASS (PAL)
NOTCH (NTSC)
NOTCH (PAL)
EXTENDED (SSAF)
CIF
QCIF

0

0

0

0

1

0

1

1

0

1

0

1

1

PASSBAND RIPPLE

MR02

0
1
0
1
0
1
0

(dB)

0.091

0.15

0.015

0.095

0.051

0.018
MONOTONIC

3 dB BANDWIDTH

(MHz)

4.157

4.74

6.54

6.24

6.217

3.0

1.5

STOPBAND

CUTOFF (MHz)

7.37

7.96

8.3

8.0

8.0

7.06

7.15

STOPBAND

ATTENUATION (dB)

–56
–64
–68
–66
–61
–61
–50

Figure 4. Luminance Internal Filter Specifications

FILTER TYPE FILTER SELECTION

MR07

MR06

0

1.3MHz LOW PASS

0.65MHz LOW PASS

1.0MHz LOW PASS

2.0MHz LOW PASS
RESERVED
CIF
QCIF

0

0

0

0

1

0

1

1

0

1

0

1

1

PASSBAND RIPPLE

MR05

0
1
0
1
0
1
0

(dB)

0.084
MONOTONIC
MONOTONIC

0.0645

0.084
MONOTONIC

3 dB BANDWIDTH

(MHz)

1.395

0.65

1.0

2.2

0.7

0.5

STOPBAND

CUTOFF (MHz)

3.01

3.64

3.73

5.0

3.01

4.08

STOPBAND

ATTENUATION (dB)

–45
–58.5
–49
–40

–45
–50

Figure 5. Chrominance Internal Filter Specifications

0

0

–10

–20

REV. B

–30

–40

MAGNITUDE – dB

–50

–60

–70

0122

46810

FREQUENCY – MHz

Figure 6. NTSC Low-Pass Luma Filter

–11–

–30

–40

MAGNITUDE – dB

–50

–60

–70

0122

46810

FREQUENCY – MHz

Figure 7. PAL Low-Pass Luma Filter

ADV7172/ADV7173

0

–10

–20

–30

–40

MAGNITUDE – dB

–50

–60

–70

0122

46810

FREQUENCY – MHz

Figure 8. NTSC Notch Luma Filter

0

–10

–20

–30

0

–10

–20

–30

–40

MAGNITUDE – dB

–50

–60

14

–70

0122

46810

FREQUENCY – MHz

14

Figure 11. CIF Luma Filter

0

–10

–20

–30

–40

MAGNITUDE – dB

–50

–60

–70

0122

46810

FREQUENCY – MHz

14

Figure 9. PAL Notch Luma Filter

0

–10

–20

–30

–40

MAGNITUDE – dB

–50

–60

–70

0122

46810

FREQUENCY – MHz

Figure 10. Extended Mode (SSAF) Luma Filter

–40

MAGNITUDE – dB

–50

–60

–70

0122

46810

FREQUENCY – MHz

14

Figure 12. QCIF Luma Filter

0

–10

–20

–30

–40

MAGNITUDE – dB

–50

–60

–70

14

0122

46810

FREQUENCY – MHz

14

Figure 13. 1.3 MHz Low-Pass Chroma Filter

–12–

REV. B

ADV7172/ADV7173

0

–10

–20

–30

–40

MAGNITUDE – dB

–50

–60

–70

0122

46810

FREQUENCY – MHz

Figure 14. 0.65 MHz Low-Pass Chroma Filter

0

–10

–20

–30

0

–10

–20

–30

–40

MAGNITUDE – dB

–50

–60

14

–70

0122

46810

FREQUENCY – MHz

14

Figure 17. CIF Chroma Filter

0

–10

–20

–30

–40

MAGNITUDE – dB

–50

–60

–70

0122

46810

FREQUENCY – MHz

Figure 15. 1.0 MHz Low-Pass Chroma Filter

0

–10

–20

–30

–40

MAGNITUDE – dB

–50

–60

–70

0122

46810

FREQUENCY – MHz

–40

MAGNITUDE – dB

–50

–60

14

–70

0122

46810

FREQUENCY – MHz

14

Figure 18. QCIF Chroma Filter

0

–5

–10

–15

MAGNITUDE – dB

–20

14

–25

0

FREQUENCY – MHz

612345

8

7

REV. B

Figure 16. 2.0 MHz Low-Pass Chroma Filter

Figure 19. Extended Mode Luma Filter with Programmable
Gain, Negative Response

–13–

ADV7172/ADV7173

4

3

2

1

0

AMPLITUDE – dB

–1

–2

–3

0

FREQUENCY – MHz

7

612345

Figure 20. Extended Mode Luma Filter with Programmable
Gain, Positive Response

COLOR BAR GENERATION

The ADV7172/ADV7173 can be configured to generate 100/

7.5/75/7.5 color bars for NTSC or 100/0/75/0 color bars for
PAL. These are enabled by setting MR46 of Mode Register 4 to
Logic “1.”

SQUARE PIXEL MODE

The ADV7172/ADV7173 can be used to operate in square pixel
mode. For NTSC operation, an input clock of 24.5454 MHz is
required. Alternatively, for PAL operation, an input clock of

29.5 MHz is required. The internal timing logic adjusts accord­ingly for square pixel mode operation.

COLOR SIGNAL CONTROL

The color information can be switched on and off the video
output using Bit MR44 of Mode Register 4.

BURST SIGNAL CONTROL

The burst information can be switched on and off the video
output using Bit MR45 of Mode Register 4.

NTSC PEDESTAL CONTROL

The pedestal on both odd and even fields can be controlled on a
line-by-line basis using the NTSC Pedestal Control Registers.
This allows the pedestals to be controlled during the Vertical
Blanking Interval.

COLOR CONTROLS

The ADV7172/ADV7173 allows the user the advantage of control­ling the brightness, contrast, hue and saturation of the color.

Contrast Control

Contrast adjustment is achieved by scaling the Y input data
by a factor programmed by the user into the Contrast Control
Register Bits 5–0. This factor allows the data to be scaled
between 75% and 125%.

Brightness Control

The brightness is controlled by adding a programmable setup
level onto the scaled Y data. This brightness level may be added

4

2

0

–2

–4

–6

MAGNITUDE – dB

–8

–10

–12

2345

FREQUENCY – MHz

61

Figure 21. Extended Mode Luma Filter with Programmable
Gain, Combined Response

onto the Y data in PAL mode, NTSC mode without pedestal or
NTSC mode with pedestal, in which case it is added directly
onto the 7.5 IRE pedestal already present.

The level added is programmed by the user into the Brightness
Control Register (Bits 4–0) and the user is capable of adding
from 0 IRE to a maximum of 14 IRE in 32 (2

5

) steps. Because
of different gains in the datapath for each mode, different values
may need to be programmed to obtain the same IRE setup level
in each mode. Maximum brightness is achieved when 31 is
programmed into the Brightness Control Register. Table I illus­trates the maximum setup/brightness amplitudes available in the
various modes. Note that if a level of less than 7.5 IRE is required
on the Y data in NTSC mode, then NTSC without pedestal
must be the mode selected.

Table I. Maximum Brightness Levels Available

Brightness Control

Mode Register Setup

NTSC No Pedestal 00011111 14 IRE
NTSC Pedestal 00011111 13 IRE
PAL 00011111 99 mV

Color Saturation Control

Color adjustment is achieved by scaling the Cr and Cb input
data by a factor programmed by the user into the Color Control
Registers 1 and 2, Bits 5–0. This factor allows the data to be
scaled between 75% and 125%.

Hue Control

The hue adjustment is achieved on the composite and chroma
outputs by adding a phase offset onto the color subcarrier in the
active video but leaving the color burst unmodified, i.e., only
the phase between the video and the color burst is modified
and hence the hue is shifted. Hue adjustment is under the con­trol of the Hue Control Register. The ADV7172/ADV7173
provides a range of ±22° change in increments of 0.17578125°.

–14–

REV. B

ADV7172/ADV7173

YUV LEVELS

This functionality is under the control of Mode Register 5, Bits
2–0. Bit 0 (MR50) allows the ADV7172/ADV7173 to output
SMPTE levels on the Y output when configured in NTSC mode,
and Betacam levels on the Y output when configured in PAL
mode and vice-versa.

Video Sync

Betacam 286 mV 714 mV
SMPTE 300 mV 700 mV
MII 300 mV 700 mV

As the datapath is branched at the output of the filters, the
luma signal relating to the CVBS or S-Video Y/C output is
unaltered. Only the Y output of the YUV outputs is scaled.
Bits 2–1 (MR52–MR51) allow UV levels to have a peak-peak
amplitude of 700 mV or 1000 mV, or the default values of
934 mV in NTSC and 700 mV in PAL.

AUTODETECT CONTROL

The ADV7172/ADV7173 provides the option of automatically
powering down the DACs A, B and C if they are not correctly
terminated (i.e., the 75 Ω cable is not connected to the DAC).
The voltage at the output of DACs A and B are compared to
a selected reference level. This reference voltage (MR64) will
depend on whether the user terminates with 37.5 Ω (75 Ω con­nected on the DAC end and 75 Ω connected at TV end of cable,
i.e., combined load of 37.5 Ω) or 75 Ω. It cannot operate in a
DAC buffering configuration. There are two modes of auto­detect operation provided by the ADV7172/ADV7173:

(1) Mode 0: The state of termination of the DAC may be read
by reading the status bits in Mode Register 6. MR67 status bit
indicates whether or not the composite DAC is terminated,
MR66 status bit indicates whether or not the luma DAC is
terminated. The user may then decide whether or not to power
down the DACs using MR15–MR0.

(2) Mode 1: The state of the DACs may be read as in Mode 0.
If either of the DACs is unterminated, they are automatically
powered down. If the luma DAC, DAC B is powered down then
DAC C, the chroma DAC, will also be powered down. The
state of termination of the DAC is checked each frame to decide
whether or not it is to be powered up or down.

Mode Register 6, Bits 3–2, indicates which mode of operation is
used. Note that Mode Register 1, Bits 5-3, must be enabled
(“1”) for autodetect functionality to work. (DACs A, B, C are
enabled.)

Vertical Blanking Data Insertion

It is possible to allow encoding of incoming YCbCr data on
those lines of VBI that do not have line sync or pre-/post­equalization pulses (see Figures 24 to 25). This mode of
operation is called “Partial Blanking” and is selected by setting
MR32 to “1.” It allows the insertion of any VBI data (Opened
VBI) into the encoded output waveform. This data is present in
digitized incoming YCbCr data stream (e.g., WSS data, CGMS,
VPS etc.). Alternatively the entire VBI may be blanked (no VBI
data inserted) on these lines by setting MR32 to “0.”

SUBCARRIER RESET

Together with the SCRESET/RTC PIN and Bits MR42 and
MR41 of Mode Register 4, the ADV7172/ADV7173 can be
used in subcarrier reset mode. The subcarrier phase will reset to
Field 0 at the start of the following field when a low to high
transition occurs on this input pin.

REAL-TIME CONTROL

Together with the SCRESET/RTC PIN and Bits MR42 and
MR41 of Mode Register 4, the ADV7172/ADV7173 can be
used to lock to an external video source. The real-time control
mode allows the ADV7172/ADV7173 to automatically alter the
subcarrier frequency to compensate for line length variation.
When the part is connected to a device that outputs a digital
data stream in the RTC format (such as a ADV7185 video
decoder, see Figure 22), the part will automatically change to
the compensated subcarrier frequency on a line-by-line basis.
This digital data stream is 67 bits wide and the subcarrier is
contained in Bits 0 to 21. Each bit is two clock cycles long. 00Hex
should be written into all four subcarrier frequency registers
when using this mode.

VIDEO TIMING DESCRIPTION

The ADV7172/ADV7173 is intended to interface to off-the­shelf MPEG1 and MPEG2 Decoders. As a consequence, the
ADV7172/ADV7173 accepts 4:2:2 YCrCb Pixel Data via a
CCIR-656 pixel port and has several video timing modes of
operation that allow it to be configured as either system master
video timing generator or a slave to the system video timing
generator. The ADV7172/ADV7173 generates all of the required
horizontal and vertical timing periods and levels for the analog
video outputs.

The ADV7172/ADV7173 calculates the width and placement
of analog sync pulses, blanking levels and color burst envelopes.
Color bursts are disabled on appropriate lines and serration and
equalization pulses are inserted where required.

In addition, the ADV7172/ADV7173 supports a PAL or NTSC
square pixel operation in slave mode. The part requires an input
pixel clock of 24.5454 MHz for NTSC and an input pixel clock
of 29.5 MHz for PAL. The internal horizontal line counters place
the various video waveform sections in the correct location for
the new clock frequencies.

The ADV7172/ADV7173 has four distinct master and four
distinct slave timing configurations. Timing control is estab­lished with the bidirectional SYNC, BLANK, and FIELD/
VSYNC pins. Timing Mode Register 1 can also be used to
vary the timing pulsewidths and where they occur in relation to
each other.

REV. B

–15–

ADV7172/ADV7173

H/LTRANSITION

COUNT START

128

RTC

TIME SLOT: 01

NOTES

1

FSC PLL INCREMENT IS 22 BITS LONG, VALUE LOADED INTO ADV7172/ADV7173 FSC DDS REGISTER IS FSC PLL INCREMENT BITS 21:0 PLUS BITS 0:9
OF SUBCARRIER FREQUENCY REGISTERS. ALL ZEROS SHOULD BE WRITTEN TO THE SUBCARRIER FREQUENCY REGISTERS OF THE
ADV7172/ADV7173.

2

SEQUENCE BIT
PAL: 0 = LINE NORMAL, 1 = LINE INVERTED
NTSC: 0 = NO CHANGE

3

RESET BIT
RESET ADV7172/ADV7173’s DDS

COMPOSITE

VIDEO

e.g., VCR

OR CABLE

LOW

LCC1

P19-P12

VIDEO

DECODER

ADV7185

14 BITS

RESERVED

NOT USED IN

ADV7172/ADV7173

013

14

GLL

4 BITS

RESERVED

21

19

CLOCK

SCRESET/RTC

P7–P0

HSYNC

FIELD/VSYNC

ADV7172/ADV7173

FSCPLL INCREMENT

VALID

SAMPLE

GREEN/COMPOSITE/Y

BLUE/LUMA/U

RED/CHROMA/V

GREEN/COMPOSITE/Y

BLUE/LUMA/U

RED/CHROMA/V

1

INVALID

SAMPLE

5 BITS

RESERVED

8/ LLC

SEQUENCE

2

BIT

0

67 68

RESET

BIT

3

RESERVED

Figure 22. RTC Timing and Connections

Mode 0 (CCIR–656): Slave Option

(Timing Register 0 TR0 = X X X X X 0 0 0)

The ADV7172/ADV7173 is controlled by the SAV (Start Active Video) and EAV (End Active Video) Time Codes in the Pixel Data.
All timing information is transmitted using a 4-byte Synchronization Pattern. A synchronization pattern is sent immediately before
and after each line during active picture and retrace. Mode 0 is illustrated in Figure 23. The HSYNC, FIELD/VSYNC, and BLANK
(if not used) pins should be tied high during this mode.

ANALOG

VIDEO

INPUT PIXELS

NTSC/PAL M SYSTEM

(525 LlNES/60Hz)

PAL SYSTEM

(625 LINES/50Hz)

EAV CODE

000

C

F

Y

Y

r

F

4 CLOCK

4 CLOCK

END OF ACTIVE

VIDEO LINE

10801

XY8

0

0

0

FF00FFABABA

ANCILLARY DATA

268 CLOCK

280 CLOCK

B

(HANC)

801

0

SAV CODE

10FF0

8
0

C

X

0

Y

0

b

VIDEO LINE

Y

0

4 CLOCK

4 CLOCK

START OF ACTIVE

C

C

Y

Y

b

r

1440 CLOCK

1440 CLOCK

C

C

Y

b

r

Figure 23. Timing Mode 0 (Slave Mode)

–16–

REV. B

ADV7172/ADV7173

Mode 0 (CCIR–656): Master Option

(Timing Register 0 TR0 = X X X X X 0 0 1)

The ADV7172/ADV7173 generates H, V, and F signals required for the SAV (Start Active Video) and EAV (End Active Video)
Time Codes in the CCIR656 standard. The H bit is output on the HSYNC pin, the V bit is output on the BLANK pin and the F bit
is output on the FIELD/VSYNC pin. Mode 0 is illustrated in Figure 24 (NTSC) and Figure 25 (PAL). The H, V, and F transitions
relative to the video waveform are illustrated in Figure 26.

DISPLAY DISPLAY

522 523 524 525 1 2 3 4

VERTICAL BLANK

67

5

10 11 20 21 22

9

8

H

V

F

DISPLAY

260 261 262 263 264 265 266 267 268 269 270 271 272 273 274

EVEN FIELD

ODD FIELD

VERTICAL BLANK

283

H

V

F

ODD FIELD

EVEN FIELD

Figure 24. Timing Mode 0 (NTSC Master Mode)

284

DISPLAY

285

DISPLAY

622 623 624 625 1 2 3 4

H

V

F

DISPLAY

309 310 311 312 314 315 316 317

ODD FIELDEVEN FIELD

313

H

V

F

ODD FIELD EVEN FIELD

Figure 25. Timing Mode 0 (PAL Master Mode)

VERTICAL BLANK

5

VERTICAL BLANK

67

318

319 320

DISPLAY

22 23

21

DISPLAY

335 336

334

REV. B

–17–

ADV7172/ADV7173

ANALOG

VIDEO

H

F

V

Figure 26. Timing Mode 0 Data Transitions (Master Mode)

Mode 1: Slave Option HSYNC, BLANK, FIELD

(Timing Register 0 TR0 = X X X X X 0 1 0)

In this mode the ADV7172/ADV7173 accepts horizontal SYNC and Odd/ Even FIELD signals. A transition of the FIELD input
when HSYNC is low indicates a new frame, i.e., Vertical Retrace. The BLANK signal is optional. When the BLANK input is dis-
abled, the ADV7172/ADV7173 automatically blanks all normally blank lines as per CCIR-624. Mode 1 is illustrated in Figure 27
(NTSC) and Figure 28 (PAL).

HSYNC

BLANK

FIELD

HSYNC

BLANK

FIELD

DISPLAY DISPLAY

522 523 524 525

DISPLAY DISPLAY

260 261 262 263 264 265

1234

ODD FIELDEVEN FIELD

266 267 268 269 270 271 272 273 274 283 284 285

ODD FIELD EVEN FIELD

VERTICAL BLANK

6

5

VERTICAL BLANK

78

10

9

11 20 21 22

Figure 27. Timing Mode 1 (NTSC)

–18–

REV. B