ANALOG DEVICES ADSP-21020 Service Manual
ADSP-21020 EZ-ICE Emulator
User’s Guide
(For Use with VisualDSP++ Release 2.0 or Higher)
First Edition, Revision 1.0, October 2002
Analog Devices, Inc.
Digital Signal Processing Division
One Technology Way
Norwood, MA 02062-9106
Part Number
82-000259-01
a
Limited Warranty
The EZ-ICE emulator is warranted against defects in materials and workmanship for a
period of one year from the date of purchase from Analog Devices or from an authorized
dealer.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without prior notice.
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use; nor for any
infringement of patents or other rights of third parties, which may result from its use. No
license is granted by implication or otherwise under the patents rights of Analog Devices,
Inc.
Copyright Information
Copyright 2002, Analog Devices, Inc., ALL RIGHTS RESERVED. This document may
not be reproduced in any form without prior, express written consent from Analog
Devices, Inc.
Trademark and Service Mark Notice
EZ-KIT Lite, VisualDSP++, VisualDSP++ logo, TigerSHARC, TigerSHARC logo,
CROSSCORE, CROSSCORE logo, Blackfin and the Blackfin logo are all trademarks of
Analog Devices Inc. EZ-ICE, SHARC and the SHARC logo are registered trademarks of
Analog Devices, Inc. All trademarks and logos are property of their respective holders.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
Adobe and Acrobat are trademarks of Adobe Systems Incorporated.
All other brand and product names are trademarks or service marks of their respective
owners.
ADSP-21020 EZ-ICE Emulator
ii
Regulatory Compliance
The ADSP-21020 EZ-ICE has been certified to comply with the essential requirements of
the European EMC directive 89/336/EEC (inclusive 93/68/EEC) and therefore carries the
CE mark.
The ADSP-21020 EZ-ICE had been appended to the Technical Construction File
referenced ‘DSPTOOLS1’ dated December 21, 1997 and was awarded CE Certification
by an appointed European Competent Body as listed below.
Technical Certificate No: Z600ANA1.005
Issued by: Technology International (Europe) Limited
41 Shrivenham Hundred Business Park
Shrivenham, Swindon, SN6 8TZ, UK
Important! The ADSP-21020 EZ-ICE contains ESD
(electrostatic discharge) sensitive devices. Electrostatic charges
readily accumulate on the human body and equipment and can
discharge without detection. Permanent damage may occur on
devices subjected to high-energy discharges. Proper ESD
precautions are recommended to avoid performance degradation
or loss of functionality. Store used EZ-ICE in the protective
shipping package.
ADSP-21020 EZ-ICE Emulator
iii
TABLE OF CONTENTS
1 INTRODUCTION.......................................................................................................................................... 1-1
1.1 FOR MORE INFORMATION ABOUT ANALOG DEVICES PRODUCTS ................................................................ 1-1
1.2 FOR TECHNICAL OR CUSTOMER SUPPORT.................................................................................................... 1-1
1.3 PURPOSE OF THIS MANUAL.......................................................................................................................... 1-2
1.4 INTENDED AUDIENCE................................................................................................................................... 1-2
1.5 MANUAL CONTENTS .................................................................................................................................... 1-2
1.6 ON-LINE HELP.............................................................................................................................................. 1-3
2 REQUIREMENTS......................................................................................................................................... 2-1
2.1 OVERVIEW ................................................................................................................................................... 2-1
2.2 CONTENTS OF YOUR EZ-ICE PACKAGE ....................................................................................................... 2-1
2.3 PC CONFIGURATION .................................................................................................................................... 2-2
3 HARDWARE INSTALLATION AND CONFIGURATION..................................................................... 3-3
3.1 UNPACKING THE EMULATOR........................................................................................................................ 3-3
3.2 REMOVING THE COVER FROM YOUR COMPUTER ......................................................................................... 3-3
3.3 SETTING THE I/O BASE ADDRESS ................................................................................................................ 3-3
3.4 INSTALLING THE ADSP-21020 EZ-ICE BOARD IN YOUR COMPUTER ......................................................... 3-4
3.5 CONNECTING THE POD TO THE ADSP-21020 EZ-ICE BOARD..................................................................... 3-4
3.6 CONNECTING THE POD TO YOUR TARGET SYSTEM ...................................................................................... 3-5
4 SOFTWARE CONFIGURATION AND INSTALLATION...................................................................... 4-1
4.1 WINDOWS 95/98 DRIVER INSTALLATION ..................................................................................................... 4-1
4.2 WINDOWS NT DRIVER INSTALLATION......................................................................................................... 4-1
4.3 WINDOWS 2000 DRIVER INSTALLATION ...................................................................................................... 4-1
4.3.1 Installing the Driver................................................................................................................................ 4-1
4.3.2 Viewing Emulator Configuration.......................................................................................................... 4-10
4.3.3 Changing Emulator Configuration ....................................................................................................... 4-11
4.4 DEBUGGER SOFTWARE INSTALLATION AND OPERATION ........................................................................... 4-12
5 SUPPORT....................................................................................................................................................... 5-1
5.1 TECHNICAL SUPPORT ................................................................................................................................... 5-1
INDEX .......................................................................................................................................................................... I
ADSP-21020 EZ-ICE Emulator
iv
LIST OF TABLES
TABLE 1-1: RELATED DSP DOCUMENTS.................................................................................................................... 1-3
TABLE 1-2: RELATED VISUALDSP++ DOCUMENTS ................................................................................................... 1-3
TABLE 2-1: MINIMUM PC CONFIGURATION ............................................................................................................... 2-2
TABLE 3-1 I/O BASE ADDRESS SWITCH SETTING EXAMPLES..................................................................................... 3-4
LIST OF FIGURES
FIGURE 4-1 WELCOME TO THE ADD/REMOVE HARDWARE WIZARD .......................................................................... 4-2
FIGURE 4-2 CHOOSE A HARDWARE TASK .................................................................................................................. 4-2
FIGURE 4-3 CHOOSE A HARDWARE DEVICE ............................................................................................................... 4-3
FIGURE 4-4 FIND NEW HARDWARE ............................................................................................................................ 4-4
FIGURE 4-5 HARDWARE TYPE.................................................................................................................................... 4-4
FIGURE 4-6 SELECT A DEVICE DRIVER....................................................................................................................... 4-5
FIGURE 4-7 INSTALL FROM DISK ............................................................................................................................... 4-5
FIGURE 4-8 SELECT A DEVICE DRIVER....................................................................................................................... 4-6
FIGURE 4-9 WINDOWS WARNING MESSAGE .............................................................................................................. 4-6
FIGURE 4-10 ADD NEW HARDWARE WIZARD PROPERTIES ........................................................................................ 4-7
FIGURE 4-11 EDIT INPUT/OUTPUT RANGE ................................................................................................................. 4-8
FIGURE 4-12 START HARDWARE INSTALLATION........................................................................................................ 4-9
FIGURE 4-13 COMPLETING THE ADD/REMOVE HARDWARE WIZARD......................................................................... 4-9
FIGURE 4-14 SYSTEM PROPERTIES ........................................................................................................................... 4-10
FIGURE 4-15 EZICE 21020-ICE ISA EMULATOR PROPERTIES................................................................................ 4-11
ADSP-21020 EZ-ICE Emulator
v
1 INTRODUCTION
The ADSP-21020 EZ-ICE emulator system provides emulation and support for the
Analog Devices ADSP-21020 DSP. It provides a controlled environment for observing,
debugging, and testing activities in a target system by connecting directly to the target
processor through the JTAG interface.
Features of the ADSP-21020 EZ-ICE system are as follows:
• Runs on Windows®95/98/2000 and Windows NT 4.0 platforms.
• Emulation for the industry-standard Analog Devices ADSP-21020 DSP.
• Rugged JTAG emulation pod.
1.1 For More Information About Analog Devices Products
Analog Devices can be accessed on the Internet at http://www.analog.com. You can
directly access the DSP Web pages at http://www.analog.com/dsp, which provides access
to DSP specific technical information and documentation, product overviews, and
product announcements. For specific information about DSP tools, go to
http://www.analog.com/dsp/tools.
You may also obtain additional information about Analog Devices and its products in any
of the following ways:
• FAX questions or requests for information to (781)-461-3010.
• Access the Computer Products Division File Transfer Protocol (FTP) site at
ftp://ftp.analogdevices.com/ or ftp://137.71.25.69 or ftp://ftp.analog.com.
1.2 For Technical or Customer Support
You can reach our Customer Support group in the following ways:
• E-mail DSP Tools questions to:
dsptools.support@analog.com
• DSP Tools Tech Support Form
http://www.analog.com/industry/dsp/tools/form_techsupport.html
ADSP-21020 EZ-ICE Emulator
1-1
• Contact your local Analog Devices sales office or an authorized Analog Devices
distributor.
• Call: (800)-ANALOGD
• E-mail general DSP questions to:
dsp.support@analog.com
dsp.europe@analog.com (European customer support)
1.3 Purpose of This Manual
The ADSP-21020 EZ-ICE Emulator User’s Guide provides directions for installing the
hardware and software on your PC.
1.4 Intended Audience
This manual is a user’s guide and reference to the ADSP-21020 EZ-ICE emulator. DSP
programmers who are familiar with Analog Devices ADSP-21020 DSP architecture,
operation, and programming are the primary audience for this manual.
DSP programmers who are unfamiliar with Analog Devices DSPs can use this manual in
conjunction with the ADSP-21020 User's Manual. DSP programmers who are unfamiliar
with VisualDSP++ should refer to the VisualDSP++ Help menu and the VisualDSP++
User’s Guide. For the locations of these documents, refer to Section 1.6.
1.5 Manual Contents
This manual contains the following information:
• Chapter 1 — INTRODUCTION
Provides manual information and Analog Devices contact information.
• Chapter 2 — REQUIREMENTS
Provides PC system requirements and package information.
• Chapter 3 — HARDWARE INSTALLATION AND CONFIGURATION
Provides information on installing the ADSP-21020 EZ-ICE.
• Chapter 4 — SOFTWARE CONFIGURATION AND INSTALLATION
Provides information on installing the EZ-ICE software.
ADSP-21020 EZ-ICE Emulator
1-2
1.6 On-line Help
Your software installation kit includes online Help as part of the Windows interface.
These Help files provide information about VisualDSP++ and the ADSP-21020 EZ-ICE
emulator.
To view the VisualDSP++’s Help, click on the Help menu item or go to the Windows
task bar and select Start\Programs\VisualDSP\VisualDSP++ Help.
The documents in the following two tables can be found through online help or in the
Docs folder of your VisualDSP++ installation.
For more documentation, please go to http://www.analog.com/dsp/tech_doc
Table 1-1: Related DSP Documents
Document Name Description
ADSP-21020 User's
Manual
General functional description, pinout, and
timing.
ADSP-21000 Family
Application Handbook
Volume 1
Table 1-2: Related VisualDSP++ Documents
Document Name Description
VisualDSP++ Users
Guide for ADSP-21xxx
DSPs
VisualDSP++
Preprocessor and
Assembler Manual for
ADSP-21xxx DSPs
VisualDSP++ C/C++
Compiler and Library
Manual for ADSP21xxx DSPs
VisualDSP++ Linker
and Utilities Manual
for ADSP-21xxx DSPs
Quick start in developing DSP applications
with ADSP-21000 family digital signal
processors.
Detailed description of VisualDSP++
features and usage.
Description of the assembler function and
commands for ADSP-21xxx family DSPs.
Description of the compiler function and
commands for ADSP-21xxx family DSPs.
Description of the linker function and
commands for the ADSP-21xxx family
DSPs.
ADSP-21020 EZ-ICE Emulator
1-3
2 REQUIREMENTS
2.1 Overview
This chapter provides you with the information you need to begin using ADSP-21020 EZICE emulator. Install your software and hardware in the order presented in Section 3 and
Section 4 for correct operation. This chapter has the following sections:
• Contents of your EZ-ICE Package (Section 2.2)
Provides a list of the components that are shipped with this EZ-ICE.
• PC Configuration (Section 2.3)
Describes the minimum requirement for the PC to work with the EZ-ICE.
2.2 Contents of your EZ-ICE Package
Your ADSP-21020 EZ-ICE Emulator package contains the following items.
• Emulator Tools CD, containing:
o ADSP-21020 specific debug software
o ADSP-21020 EZ-ICE Manual (this document)
• PC Plug-in card, probe and connecting cable
• ADSP-21020 data sheet and anomaly list
• Registration card - please fill out and return
If any item is missing, contact the vendor where you purchased your EZ-ICE or contact
Analog Devices, Inc.
The ADSP-21020 EZ-ICE contains ESD (electrostatic
discharge) sensitive devices. Electrostatic charges
readily accumulate on the human body and equipment
and can discharge without detection. Permanent
damage may occur on devices subjected to highenergy discharges. Proper ESD precautions are
recommended to avoid performance degradation or
loss of functionality. Store used EZ-ICE in the
protective shipping package.
ADSP-21020 EZ-ICE Emulator
2-1
Loading...