Analog Devices ADN2816 pra Datasheet

Continuous Rate 12.3 Mb/s to 675 Mb/s Clock and

Preliminary Technical Data

FEATURES

Serial data input: 12.3 Mb/s to 675 Mb/s
Exceeds SONET requirements for jitter transfer/

generation/tolerance
Patented clock recovery architecture
No reference clock required
Loss of lock indicator

2

C™ interface to access optional features

I
Single-supply operation: 3.3 V
Low power: 300 mW typical
5 mm × 5 mm 32-lead LFCSP, Pb Free

APPLICATIONS

SONET OC-1/3/12 and all associated FEC rates
Fibre Channel, ESCON, Fast Ethernet, SDI, etc.
WDM transponders
Regenerators/repeaters
Test equipment
Broadband cross-connects and routers

PRODUCT DESCRIPTION

The ADN2816 provides the receiver functions of quantization
and clock and data recovery for continuous data rates from 12.3
Mb/s to 675 Mb/s. The ADN2816 automatically locks to all data
rates without the need for an external reference clock or
programming. All SONET jitter requirements are met,
including jitter transfer, jitter generation, and jitter tolerance.
All specifications are quoted for −40°C to +85°C ambient
temperature, unless otherwise noted.

The ADN2816 is available in a compact 5 mm × 5 mm 32-lead
chip scale package.

FUNCTIONAL BLOCK DIAGRAM

REFCLKP/N
(OPTIONAL)

LOL

Data Recovery IC

ADN2816

VCC VEECF1 CF2

PIN

NIN

VREF

Rev. PrA

Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.

BUFFER

PHASE

SHIFTER

DATA

RE-TIMING

2

DATAOUTP/N DRVEE DVCCDRVCC DVEECLKOUTP/N

FREQUENCY

DETECT

PHASE

DETECT

2

Figure 1.

LOOP

FILTER

LOOP

FILTER

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] www.analog.com
Fax: [phone] © 2004 Analog Devices, Inc. All rights reserved.

VCO

04948-0-001

ADN2816 Preliminary Technical Data

TABLE OF CONTENTS

Specifications..................................................................................... 3

Jitter Specifications....................................................................... 4

Output and Timing Specifications............................................. 5

Absolute Maximum Ratings............................................................ 6

Thermal Characteristics .............................................................. 6

ESD Caution.................................................................................. 6

Timing Characteristics..................................................................... 7

Pin Configuration and Function Descriptions............................. 8

Typical Performance Characteristics ............................................. 9

I2C Interface Timing and Internal Register Description........... 10

Jitter Specifications ......................................................................... 12

Jitter Generation .........................................................................12

Jitter Transfer............................................................................... 12

Jitter Tolerance............................................................................ 12

Theory of Operation ...................................................................... 13

Functional Description.................................................................. 15

Frequency Acquisition............................................................... 15

Input buffer................................................................................. 15

Lock Detector Operation .......................................................... 15

Harmonic Detector.................................................................... 16

Squelch Mode ............................................................................. 16

I2C Interface ................................................................................ 16

Reference Clock (Optional) ...................................................... 17

Applications Information.............................................................. 20

PCB Design Guidelines ............................................................. 20

Coarse Data Rate Readback Look-Up Table............................... 23

Outline Dimensions....................................................................... 25

Ordering Guide .......................................................................... 25

REVISION HISTORY

6/04—Revision PrA: Initial Version

Rev. PrA | Page 2 of 27

Preliminary Technical Data ADN2816

SPECIFICATIONS

TA = T
unless otherwise noted.

Table 1.

Parameter Conditions Min Typ Max Unit

QUANTIZER—DC CHARACTERISTICS

QUANTIZER—AC CHARACTERISTICS

LOSS OF LOCK DETECT (LOL)

ACQUISITION TIME
Lock to Data Mode OC-12 2.0 ms
OC-3 3.4 ms
OC-1 9.8 ms

12.3 Mb/s 40.0 ms

DATA RATE READBACK ACCURACY

POWER SUPPLY VOLTAGE 3.0 3.3 3.6 V
POWER SUPPLY CURRENT 90 mA
OPERATING TEMPERATURE RANGE –40 +85 °C

to T

MIN

Input Voltage Range @ PIN or NIN, dc-coupled 1.8 2.8 V

Peak-to-Peak Differential Input PIN – NIN 0.2 2.0 V

Input Common Mode Level DC-coupled 2.3 2.5 2.8 V

Data Rate 12.3 675 Mb/s

S11 @ 2.5 GHz −15 dB

Input Resistance Differential 100

Input Capacitance 0.65 pF

VCO Frequency Error for LOL Assert With respect to nominal 1000 ppm

VCO Frequency Error for LOL De-Assert With respect to nominal 250 ppm

LOL Response Time 12.3 Mb/s 4 ms

OC-12 1.0 µs

Optional Lock to REFCLK Mode 10.0 ms

Coarse Readback (See Table 13) 10 %

Fine Readback In addition to REFCLK accuracy

Data rate < 20 Mb/s 200 ppm

Data rate > 20 Mb/s 100 ppm

, VCC = V

MAX

MIN

to V

, VEE = 0 V, CF = 0.47 µF, SLICEP = SLICEN = VEE, Input Data Pattern: PRBS 223 − 1,

MAX

Ω

Rev. PrA | Page 3 of 27

ADN2816 Preliminary Technical Data

JITTER SPECIFICATIONS

TA = T
unless otherwise noted.

Table 2.

Parameter Conditions Min Typ Max Unit

PHASE-LOCKED LOOP CHARACTERISTICS

30 Hz1 100 UI p-p
300 Hz1 44 UI p-p
25 kHz 2.5 UI p-p
250 kHz1 1.0 UI p-p
OC-3, 223 − 1 PRBS
30 Hz1 50 UI p-p
300 Hz1 24 UI p-p
6500 Hz 3.5 UI p-p
65 kHz 1.0 UI p-p

1

Jitter tolerance of the ADN2816 at these jitter frequencies is better than what the test equipment is able to measure.

MIN

to T

, VCC = V

MAX

MIN

to V

, VEE = 0 V, CF = 0.47 uF, SLICEP = SLICEN = VEE, Input Data Pattern: PRBS 223 − 1,

MAX

Jitter Transfer BW OC-12 71 108 kHz
OC-3 23 35 kHz
Jitter Peaking OC-12 0 0.03 dB
OC-3 0 0.03 dB
Jitter Generation OC-12, 12 kHz to 5 MHz 0.001 0.002 UI rms

0.01 0.019 UI p-p
OC-3, 12 kHz to 1.3 MHz 0.001 0.002 UI rms

0.01 0.011 UI p-p

Jitter Tolerance OC-12, 223 − 1 PRBS

Rev. PrA | Page 4 of 27

Preliminary Technical Data ADN2816

OUTPUT AND TIMING SPECIFICATIONS

Table 3.

Parameter Conditions Min Typ Max Unit

LVDS OUPUT CHARACTERISTICS

(CLKOUTP/N, DATAOUTP/N)

Single-Ended Output Swing VSE (see Figure 3) 250 400 mV
Differential Output Swing V
Output Offset Voltage 1125 1200 1275 mV
Output Impedance Differential 100

LVDS Ouputs Timing

Rise Time 20% to 80% 100 ps
Fall Time 80% to 20% 100 ps
Setup Time TS (see Figure 2), OC12 800 ps
Hold Time TH (see Figure 2), OC12 800 ps

I2C INTERFACE DC CHARACTERISTICS LVCMOS

Input High Voltage VIH 0.7 VCC V

Input Low Voltage VIL 0.3 VCC V

Input Current VIN = 0.1 VCC or VIN = 0.9 VCC −10.0 +10.0 µA

Output Low Voltage VOL, I
I2C INTERFACE TIMING (See Figure 9)

SCK Clock Frequency 400 kHz

SCK Pulse Width High t

SCK Pulse Width Low t

Start Condition Hold Time t

Start Condition Setup Time t

Data Setup Time t

Data Hold Time t

SCK/SDA Rise/Fall Time TR/TF 20 + 0.1 Cb

Stop Condition Setup Time t

Bus Free Time between a Stop and a Start t
REFCLK CHARACTERISTICS Optional lock to REFCLK mode

Input Voltage Range @ REFCLKP or REFCLKN

V

V

Minimum Differential Input Drive 100 mV p-p

Reference Frequency 12.3 200 MHz

Required Accuracy 100 ppm
LVTTL DC INPUT CHARACTERISTICS

Input High Voltage VIH 2.0 V

Input Low Voltage VIL 0.8 V

Input High Current IIH, VIN = 2.4 V 5 µA

Input Low Current IIL, VIN = 0.4 V −5 µA
LVTTL DC OUTPUT CHARACTERISTICS

Output High Voltage VOH, IOH = −2.0 mA 2.4 V

Output Low Voltage VOL, IOL = 2.0 mA 0.4 V

1

Cb = total capacitance of one bus line in pF. If mixed with Hs-mode devices, faster fall-times are allowed.

(see Figure 3) 500 800 mV

DIFF

Ω

= 3.0 mA 0.4 V

OL

600 ns

HIGH

1300 ns

LOW

600 ns

HD;STA

600 ns

SU;STA

100 ns

SU;DAT

300 ns

HD;DAT

600 ns

SU;STO

1300 ns

BUF

0 V

IL

VCC V

IH

1

300 ns

Rev. PrA | Page 5 of 27

ADN2816 Preliminary Technical Data

ABSOLUTE MAXIMUM RATINGS

TA = T
µF, SLICEP = SLICEN = VEE, unless otherwise noted.

Table 4.

Parameter Rating

Supply Voltage (VCC) 4.2 V
Minimum Input Voltage (All Inputs) VEE − 0.4 V
Maximum Input Voltage (All Inputs) VCC + 0.4 V
Maximum Junction Temperature 125°C
Storage Temperature −65°C to +150°C
Lead Temperature (Soldering 10 s) 300°C

ESD CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.

MIN

to T

, VCC = V

MAX

MIN

to V

, VEE = 0 V, CF = 0.47

MAX

Stress above those listed under Absolute Maximum Ratings may
cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other
conditions above those indicated in the operational sections of
this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.

THERMAL CHARACTERISTICS

Thermal Resistance

32-LFCSP, 4-layer board with exposed paddle soldered to VEE

= 28°C/W.

θ

JA

Rev. PrA | Page 6 of 27

Preliminary Technical Data ADN2816

TIMING CHARACTERISTICS

CLKOUTP

T

T

S

H

DATAOUTP/N

04948-0-002

Figure 2. Output Timing

OUTP

OUTN

OUTP–OUTN

V

CML

V

0V

SE

V

DIFF

V

SE

04948-0-003

Figure 3. Single-Ended vs. Differential Output Specifications

Rev. PrA | Page 7 of 27

ADN2816 Preliminary Technical Data

*

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

32 TEST2

31 VCC

30 VEE

29 DATAOUTP

28 DATAOUTN

27 SQUELCH

26 CLKOUTP

25 CLKOUTN

TEST1 1

VCC 2

VREF 3

NIN 4
PIN 5

NC 6
NC 7

VEE 8

THERE IS AN EXPOSED PAD ON THE BOTTOM OF
THE PACKAGE THAT MUST BE CONNECTED TO GND.

PIN 1
INDICATOR

ADN2816*

TOP VIEW

(Not to Scale)

NC 9

VCC 12

REFCLKP 10

REFCLKN 11

CF2 14

VEE 13

CF1 15

LOL 16

24 VCC
23 VEE
22 NC
21 SDA
20 SCK
19 SADDR5
18 VCC
17 VEE

04948-0-004

Figure 4. Pin Configuration

Table 5. Pin Function Descriptions

Pin No. Mnemonic Type1 Description

1 TEST1 Connect to VCC.
2 VCC P Power for Limamp, LOS.
3 VREF AO Internal VREF Voltage. Decouple to GND with a 0.1 µF capacitor.
4 NIN AI Differential Data Input. CML.
5 PIN AI Differential Data Input. CML.
6 ,7 NC No Connect
8 VEE P GND for Limamp, LOS.
9 NC No Connect
10 REFCLKP DI Differential REFCLK Input. 12.3 MHz to 200 MHz.
11 REFCLKN DI Differential REFCLK Input. 12.3 MHz to 200 MHz.
12 VCC P VCO Power.
13 VEE P VCO GND.
14 CF2 AO Frequency Loop Capacitor.
15 CF1 AO Frequency Loop Capacitor.
16 LOL DO Loss of Lock Indicator. LVTTL active high.
17 VEE P FLL Detector GND.
18 VCC P FLL Detector Power.
19 SADDR5 DI Slave Address Bit 5.
20 SCK DI I
21 SDA DI I
22 NC No Connect
23 VEE P Output Buffer, I
24 VCC P Output Buffer, I
25 CLKOUTN DO Differential Recovered Clock Output. LVDS.
26 CLKOUTP DO Differential Recovered Clock Output. LVDS.
27 SQUELCH DI Disable Clock and Data Outputs. Active high. LVTLL.
28 DATAOUTN DO Differential Recovered Data Output. LVDS.
29 DATAOUTP DO Differential Recovered Data Output. LVDS.
30 VEE P Phase Detector, Phase Shifter GND.
31 VCC P Phase Detector, Phase Shifter Power.
32 TEST2 Connect to VCC.
Exposed Pad Pad P Connect to GND

1

Type: P = power, AI = analog input, AO = analog output, DI = digital input, DO = digital output.

2

C Clock Input.

2

C Data Input.

2

C GND.

2

C Power.

Rev. PrA | Page 8 of 27

Preliminary Technical Data ADN2816

TYPICAL PERFORMANCE CHARACTERISTICS

Rev. PrA | Page 9 of 27