ANALOG DEVICES ADL5565 Service Manual
6 GHz Ultrahigh Dynamic Range
V
V
V
Data Sheet
FEATURES
3 dB bandwidth of 6 GHz (AV = 6 dB)
Pin strappable gain adjust: 6 dB, 12 dB, and 15.5 dB
Gain range from 0 dB to 15.5 dB using two external resistors
Differential or single-ended input to differential output
Low noise input stage: NF = 8.7 dB at 15.5 dB gain
Low broadband distortion (A
10 MHz: −107 dBc (HD2), −110 dBc (HD3)
100 MHz: −108 dBc (HD2), −103 dBc (HD3)
200 MHz: −82 dBc (HD2), −87 dBc (HD3)
500 MHz: −68 dBc (HD2), −63 dBc (HD3)
IMD3 of −113 dBc at 100 MHz center
Slew rate: 11 V/ns
Fast settling and overdrive recovery of 2 ns
Single-supply operation: 2.8 V to 5.2 V
Power down
Fabricated using the high speed XFCB3 SiGe process
APPLICATIONS
Differential ADC drivers
Single-ended-to-differential conversion
RF/IF gain blocks
SAW filter interfacing
GENERAL DESCRIPTION
The ADL5565 is a high performance differential amplifier
optimized for RF and IF applications. The amplifier offers low
noise of 1.5 nV/√Hz and excellent distortion performance over
a wide frequency range making it an ideal driver for high speed
8-bit to 16-bit analog-to-digital converters (ADCs).
The ADL5565 provides three gain levels of 6 dB, 12 dB, and 15.5 dB
through a pin strappable configuration. For the single-ended
input configuration, the gains are reduced to 5.3 dB, 10.3 dB,
and 13 dB. Using two external series resistors expands the gain
flexibility of the amplifier and allows for any gain selection from
0 dB to 15.5 dB for a differential input and 0 dB to 13 dB for a
single-ended input.
= 6 dB)
V
Differential Amplifier
ADL5565
FUNCTIONAL BLOCK DIAGRAM
CC
R
F
R
G2
VIP2
R
G1
VIP1
R
G1
IN1
R
G2
IN2
R
F
ADL5565
GND
Figure 1.
The quiescent current of the ADL5565 is typically 70 mA, and
when disabled, consumes less than 5 mA with −25 dB of inputto-output isolation at 100 MHz.
The device is optimized for wideband, low distortion, and noise
performance, giving it unprecedented performance for overall
spurious-free dynamic range. These attributes, together with its
adjustable gain capability, make this device the amplifier of
choice for driving a wide variety of ADCs, mixers, pin diode
attenuators, SAW filters, and multielement discrete devices.
Fabricated on an Analog Devices, Inc., high speed SiGe process,
the ADL5565 is supplied in a compact 3 mm × 3 mm, 16-lead
LFCSP package and operates over the −40°C to +85°C
temperature range.
ENBL
VON
VCOM
VOP
09959-001
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.461.3113 ©2011–2012 Analog Devices, Inc. All rights reserved.
ADL5565 Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications ....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description ......................................................................... 1
Revision History ............................................................................... 2
Specifications ..................................................................................... 3
3.3 V Specifications ...................................................................... 3
5 V Specifications ......................................................................... 6
Absolute Maximum Ratings ............................................................ 9
ESD Caution .................................................................................. 9
Pin Configuration and Function Descriptions ........................... 10
Typical Performance Characteristics ........................................... 11
Circuit Description ......................................................................... 16
REVISION HISTORY
6/12—Rev. A to Rev. B
Changes to Ordering Guide .......................................................... 26
4/12—Rev. 0 to Rev. A
Changes to Table 3; Added Thermal Resistance Section and
Table 4, Renumbered Sequentially ................................................. 9
Deleted Soldering Information Section ....................................... 23
Added Soldering Information and Recommended PCB
Land Pattern Section and Figure 44, Renumbered
Sequentially ..................................................................................... 23
Updated Outline Dimensions ....................................................... 26
10/11— Revision 0: Initial Version
Basic Structure ............................................................................ 16
Applications Information .............................................................. 17
Basic Connections ...................................................................... 17
Input and Output Interfacing ................................................... 18
Gain Adjustment and Interfacing ............................................ 19
ADC Interfacing ......................................................................... 20
Layout Considerations ............................................................... 22
Soldering Information and Recommended PCB Land
Pattern .......................................................................................... 23
Evaluation Board ........................................................................ 23
Outline Dimensions ....................................................................... 26
Ordering Guide .......................................................................... 26
Rev. B | Page 2 of 28
Data Sheet ADL5565
AV = 12 dB, V
≤ 1.0 V p-p
6500
MHz
Input Common-Mode Range
AV = 6 dB, 12 dB, and 15.5 dB
1.2 to 2
V
CMRR
60 dB
ENBL Input Bias Current
ENBL high
500 nA
B
SPECIFICATIONS
3.3 V SPECIFICATIONS
VS = 3.3 V, VCM = 1.65 V, RL = 200 Ω differential, AV = 6 dB, CL = 1 pF differential, f = 100 MHz, TA = 25°C; parameters specified
ac-coupled differential input and differential output, unless otherwise noted.
Table 1.
Parameter Test Conditions/Comments Min Typ Max Unit
DYNAMIC PERFORMANCE
−3 dB Bandwidth AV = 6 dB, V
AV = 15.5 dB, V
Bandwidth for 0.1 dB Flatness V
≤ 1.0 V p-p 1000 MHz
OUT
Gain Accuracy ±1 dB
Gain Supply Sensitivity VS ± 5% 1.9 mdB/V
Gain Temperature Sensitivity −40°C to +85°C 0.35 mdB/°C
Slew Rate
Rise, A
V
= 2 V step
V
OUT
= 15.5 dB, RL = 200 Ω,
Fall, A
V
= 2 V step
V
OUT
Settling Time 2 V step to 1% 2 ns
Overdrive Recovery Time VIN = 4 V to 0 V step, V
Reverse Isolation (S12) 70 dB
INPUT/OUTPUT CHARACTERISTICS
≤ 1.0 V p-p 6750 MHz
OUT
OUT
≤ 1.0 V p-p 6250 MHz
OUT
= 15.5 dB, RL = 200 Ω,
11 V/ns
11 V/ns
≤ ±10 mV <3 ns
OUT
Output Common-Mode Range 1.4 to 1.8 V
Maximum Output Voltage Swing 1 dB compressed 4 V p-p
Output Common-Mode Offset Referenced to VCC/2 −100 +20 mV
Output Common-Mode Drift −40°C to +85°C 0.34 mV/°C
Output Differential Offset Voltage −20 +20 mV
Output Differential Offset Drift −40°C to +85°C 1.5 mV/°C
Input Bias Current ±5 µA
Input Resistance (Differential) AV = 6 dB 200 Ω
AV = 12 dB 100 Ω
AV = 15.5 dB 67 Ω
Input Resistance (Single-Ended) AV = 5.6 dB 158 Ω
AV = 11.1 dB 96 Ω
AV = 14.1 dB 74 Ω
Input Capacitance (Single-Ended) 0.3 pF
Output Resistance (Differential) 10 Ω
POWER INTERFACE
Supply Voltage 2.8 3.3 5.2 V
ENBL Threshold 1.5 V
ENBL low −165 µA
Quiescent Current ENBL high 70 mA
ENBL low 5 mA
Rev. | Page 3 of 28
ADL5565 Data Sheet
AV = 15.5 dB, RL = 200 Ω, V
= 2 V p-p
−106/−112
dBc
Second/Third Harmonic Distortion (HD2/HD3)
AV = 6 dB, RL = 200 Ω, V
= 2 V p-p
−108/−103
dBc
AV = 12 dB, RL = 200 Ω, V
=
+53/−112
dBm/dBc
−85 dBc
AV = 12 dB
12.8 dBm
B
Parameter Test Conditions/Comments Min Typ Max Unit
NOISE/HARMONIC PERFORMANCE
10 MHz
Second/Third Harmonic Distortion (HD2/HD3) AV = 6 dB, RL = 200 Ω, V
AV = 12 dB, RL = 200 Ω, V
Output IP3/Third-Order Intermodulation
Distortion (OIP3/IMD3)
AV = 6 dB, RL = 200 Ω, V
2 V p-p composite (2 MHz spacing)
= 12 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
= 15.5 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
Second-Order Intermodulation Distortion (IMD2)
= 6 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
= 12 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
= 15.5 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
Noise Spectral Density, RTI (NSD) AV = 6 dB 2.24 nV/√Hz
AV = 12 dB 1.52 nV/√Hz
AV = 15.5 dB 1.53 nV/√Hz
Noise Figure (NF) AV = 6 dB 10.24 dB
AV = 12 dB 8.66 dB
AV = 15.5 dB 8.78 dB
1 dB Compression Point, RTO (OP1dB) AV = 6 dB 13.1 dBm
AV = 12 dB 12.8 dBm
AV = 15.5 dB 13.1 dBm
100 MHz
AV = 12 dB, RL = 200 Ω, V
AV = 15.5 dB, RL = 200 Ω, V
Output IP3/Third-Order Intermodulation
Distortion (OIP3/IMD3)
AV = 6 dB, RL = 200 Ω, V
2 V p-p composite (2 MHz spacing)
2 V p-p composite (2 MHz spacing)
= 15.5 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
Second-Order Intermodulation Distortion (IMD2)
= 6 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
AV = 12 dB, RL = 200 Ω, V
2 V p-p composite (2 MHz spacing)
= 15.5 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
Noise Spectral Density, RTI (NSD) AV = 6 dB 2.25 nV/√Hz
AV = 12 dB 1.53 nV/√Hz
AV = 15.5 dB 1.52 nV/√Hz
Noise Figure (NF) AV = 6 dB 10.27 dB
AV = 12 dB 8.69 dB
AV = 15.5 dB 8.7 dB
1 dB Compression Point, RTO (OP1dB) AV = 6 dB 13 dBm
= 2 V p-p −107/−110 dBc
OUT
= 2 V p-p −101/−107 dBc
OUT
OUT
=
OUT
=
OUT
=
OUT
=
OUT
=
OUT
=
OUT
OUT
= 2 V p-p −91/−99 dBc
OUT
= 2 V p-p −89/−100 dBc
OUT
=
OUT
OUT
=
OUT
=
OUT
=
OUT
=
OUT
+48/−100 dBm/dBc
+52/−108 dBm/dBc
+50/−105 dBm/dBc
−86 dBc
−86 dBc
−86 dBc
+54/−113 dBm/dBc
+52/−111 dBm/dBc
−85 dBc
−86 dBc
AV = 15.5 dB 12.8 dBm
Rev. | Page 4 of 28
Data Sheet ADL5565
Output IP3/Third-Order Intermodulation
AV = 6 dB, RL = 200 Ω, V
=
+46/−97
dBm/dBc
Second-Order Intermodulation Distortion (IMD2)
−85 dBc
Noise Spectral Density, RTI (NSD)
AV = 6 dB
2.62 nV/√Hz
B
Parameter Test Conditions/Comments Min Typ Max Unit
200 MHz
Second/Third Harmonic Distortion (HD2/HD3) AV = 6 dB, RL = 200 Ω, V
AV = 12 dB, RL = 200 Ω, V
AV = 15.5 dB, RL = 200 Ω, V
Distortion (OIP3/IMD3)
2 V p-p composite
= 12 dB, RL = 200 Ω, V
A
V
2 V p-p composite
= 15.5 dB, RL = 200 Ω, V
A
V
2 V p-p composite
AV = 6 dB, RL = 200 Ω, V
2 V p-p composite (2 MHz spacing)
= 12 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
= 15.5 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
Noise Spectral Density, RTI (NSD) AV = 6 dB 2.36 nV/√Hz
AV = 12 dB 1.64 nV/√Hz
AV = 15.5 dB 1.51 nV/√Hz
Noise Figure (NF) AV = 6 dB 10.65 dB
AV = 12 dB 9.25 dB
AV = 15.5 dB 8.49 dB
500 MHz
Second/Third Harmonic Distortion (HD2/HD3) AV = 6 dB, RL = 200 Ω, V
AV = 12 dB, RL = 200 Ω, V
AV = 15.5 dB, RL = 200 Ω, V
Output IP3/Third-Order Intermodulation
Distortion (OIP3/IMD3)
AV = 6 dB, RL = 200 Ω, V
2 V p-p composite
= 12 dB, RL = 200 Ω, V
A
V
2 V p-p composite
= 15.5 dB, RL = 200 Ω, V
A
V
2 V p-p composite
Second-Order Intermodulation Distortion (IMD2)
= 6 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
= 12 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
= 15.5 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
= 2 V p-p −82/−87 dBc
OUT
= 2 V p-p −72/−86 dBc
OUT
= 2 V p-p −71/−86 dBc
OUT
OUT
=
OUT
=
OUT
=
OUT
=
OUT
=
OUT
= 2 V p-p −68/−63 dBc
OUT
= 2 V p-p −56/−62 dBc
OUT
= 2 V p-p −57/−63 dBc
OUT
=
OUT
=
OUT
=
OUT
=
OUT
=
OUT
=
OUT
+46/−99 dBm/dBc
+46/−98 dBm/dBc
−73 dBc
−70 dBc
+34/−77 dBm/dBc
+36/−82 dBm/dBc
+39/−88 dBm/dBc
−75 dBc
−70 dBc
−70 dBc
AV = 12 dB 1.57 nV/√Hz
AV = 15.5 dB 1.47 nV/√Hz
Noise Figure (NF) AV = 6 dB 11.47 dB
AV = 12 dB 8.93 dB
AV = 15.5 dB 8.07 dB
Rev. | Page 5 of 28
ADL5565 Data Sheet
Bandwidth for 0.1 dB Flatness
V
≤ 1.0 V p-p
1000
MHz
11 V/ns
Input Bias Current
±5 µA
Quiescent Current
ENBL high
80 mA
B
5 V SPECIFICATIONS
VS = 5.0 V, VCM = 2.5 V, RL = 200 Ω differential, AV = 6 dB, CL = 1 pF differential, f = 100 MHz, TA = 25°C; parameters specified
ac-coupled differential input and differential output, unless otherwise noted.
Table 2.
Parameter Test Conditions/Comments Min Typ Max Unit
DYNAMIC PERFORMANCE
−3 dB Bandwidth AV = 6 dB, V
AV = 12 dB, V
AV = 15.5 dB, V
OUT
Gain Accuracy ±1 dB
Gain Supply Sensitivity VS ± 5% 1.6 mdB/V
Gain Temperature Sensitivity −40°C to +85°C 0.37 mdB/°C
Slew Rate
Rise, A
= 2 V step
V
OUT
Fall, AV = 15.5 dB, RL = 200 Ω,
= 2 V step
V
OUT
Settling Time 2 V step to 1% 2 ns
Overdrive Recovery Time VIN = 4 V to 0 V step, V
Reverse Isolation (S12) 70 dB
INPUT/OUTPUT CHARACTERISTICS
Input Common-Mode Range AV = 6 dB, 12 dB, and 15.5 dB 1.2 to 3.8 V
Output Common-Mode Range 1.4 to 3 V
Maximum Output Voltage Swing 1 dB compressed 8 V p-p
Output Common-Mode Offset Referenced to VCC/2 −100 +20 mV
Output Common-Mode Drift −40°C to +85°C 0.4 mV/°C
Output Differential Offset Voltage −20 +20 mV
CMRR 60 dB
Output Differential Offset Drift −40°C to +85°C 1.5 mV/°C
≤ 1.0 V p-p 7000 MHz
OUT
≤ 1.0 V p-p 6750 MHz
OUT
≤ 1.0 V p-p 6500 MHz
OUT
= 15.5 dB, RL = 200 Ω,
V
≤ ±10 mV <3 ns
OUT
11 V/ns
Input Resistance (Differential) AV = 6 dB 200 Ω
AV = 12 dB 100 Ω
AV = 15.5 dB 67 Ω
Input Resistance (Single-Ended) AV = 5.6 dB 158 Ω
AV = 11.1 dB 96 Ω
AV = 14.1 dB 74 Ω
Input Capacitance (Single-Ended) 0.3 pF
Output Resistance (Differential) 10 Ω
POWER INTERFACE
Supply Voltage 2.8 5 5.2 V
ENBL Threshold 1.5 V
ENBL Input Bias Current ENBL high 1 µA
ENBL low −250 µA
ENBL low 6 mA
Rev. | Page 6 of 28
Data Sheet ADL5565
AV = 15.5 dB, RL = 200 Ω, V
= 2 V p-p
−105/−106
dBc
Second/Third Harmonic Distortion (HD2/HD3)
AV = 6 dB, RL = 200 Ω, V
= 2 V p-p
−108/−109
dBc
AV = 12 dB, RL = 200 Ω, V
=
+53/−112
dBm/dBc
−91 dBc
AV = 12 dB
16.5 dBm
B
Parameter Test Conditions/Comments Min Typ Max Unit
NOISE/HARMONIC PERFORMANCE
10 MHz
Second/Third Harmonic Distortion (HD2/HD3) AV = 6 dB, RL = 200 Ω, V
AV = 12 dB, RL = 200 Ω, V
Output IP3/Third-Order Intermodulation
Distortion (OIP3/IMD3)
AV = 6 dB, RL = 200 Ω, V
2 V p-p composite (2 MHz spacing)
= 12 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
= 15.5 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
Second-Order Intermodulation Distortion (IMD2)
= 6 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
= 12 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
= 15.5 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
Noise Spectral Density, RTI (NSD) AV = 6 dB 2.25 nV/√Hz
AV = 12 dB 1.54 nV/√Hz
AV = 15.5 dB 1.55 nV/√Hz
Noise Figure (NF) AV = 6 dB 10.29 dB
AV = 12 dB 8.77 dB
AV = 15.5 dB 9.04 dB
1 dB Compression Point, RTO (OP1dB) AV = 6 dB 16.8 dBm
AV = 12 dB 16.7 dBm
AV = 15.5 dB 16.6 dBm
100 MHz
AV = 12 dB, RL = 200 Ω, V
AV = 15.5 dB, RL = 200 Ω, V
Output IP3/Third-Order Intermodulation
Distortion (OIP3/IMD3)
AV = 6 dB, RL = 200 Ω, V
2 V p-p composite (2 MHz spacing)
2 V p-p composite (2 MHz spacing)
= 15.5 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
Second-Order Intermodulation Distortion (IMD2)
= 6 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
AV = 12 dB, RL = 200 Ω, V
2 V p-p composite (2 MHz spacing)
= 15.5 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
Noise Spectral Density, RTI (NSD) AV = 6 dB 2.28 nV/√Hz
AV = 12 dB 1.53 nV/√Hz
AV = 15.5 dB 1.52 nV/√Hz
Noise Figure (NF) AV = 6 dB 10.39 dB
AV = 12 dB 8.73 dB
AV = 15.5 dB 8.7 dB
1 dB Compression Point, RTO (OP1dB) AV = 6 dB 16.8 dBm
= 2 V p-p −111/−116 dBc
OUT
= 2 V p-p −100/−104 dBc
OUT
OUT
=
OUT
=
OUT
=
OUT
=
OUT
=
OUT
=
OUT
OUT
= 2 V p-p −92/−103 dBc
OUT
= 2 V p-p −89.5/−105 dBc
OUT
=
OUT
OUT
=
OUT
=
OUT
=
OUT
=
OUT
+47/−99 dBm/dBc
+50/−105 dBm/dBc
+50/−105 dBm/dBc
−78 dBc
−86 dBc
−91 dBc
+53/−112 dBm/dBc
+52/−110 dBm/dBc
−87 dBc
−87 dBc
AV = 15.5 dB 16.4 dBm
Rev. | Page 7 of 28
ADL5565 Data Sheet
Output IP3/Third-Order Intermodulation
AV = 6 dB, RL = 200 Ω, V
=
+46/−97
dBm/dBc
Second-Order Intermodulation Distortion (IMD2)
−85 dBc
Noise Spectral Density, RTI (NSD)
AV = 6 dB
2.64 nV/√Hz
B
Parameter Test Conditions/Comments Min Typ Max Unit
200 MHz
Second/Third Harmonic Distortion (HD2/HD3) AV = 6 dB, RL = 200 Ω, V
AV = 12 dB, RL = 200 Ω, V
AV = 15.5 dB, RL = 200 Ω, V
Distortion (OIP3/IMD3)
2 V p-p composite
= 12 dB, RL = 200 Ω, V
A
V
2 V p-p composite
= 15.5 dB, RL = 200 Ω, V
A
V
2 V p-p composite
AV = 6 dB, RL = 200 Ω, V
2 V p-p composite (2 MHz spacing)
= 12 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
= 15.5 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
Noise Spectral Density, RTI (NSD) AV = 6 dB 2.43 nV/√Hz
AV = 12 dB 1.63 nV/√Hz
AV = 15.5 dB 1.51 nV/√Hz
Noise Figure (NF) AV = 6 dB 10.88 dB
AV = 12 dB 9.2 dB
AV = 15.5 dB 8.54 dB
500 MHz
Second/Third Harmonic Distortion (HD2/HD3) AV = 6 dB, RL = 200 Ω, V
AV = 12 dB, RL = 200 Ω, V
AV = 15.5 dB, RL = 200 Ω, V
Output IP3/Third-Order Intermodulation
Distortion (OIP3/IMD3)
AV = 6 dB, RL = 200 Ω, V
2 V p-p composite
= 12 dB, RL = 200 Ω, V
A
V
2 V p-p composite
= 15.5 dB, RL = 200 Ω, V
A
V
2 V p-p composite
Second-Order Intermodulation Distortion (IMD2)
= 6 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
= 12 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
= 15.5 dB, RL = 200 Ω, V
A
V
2 V p-p composite (2 MHz spacing)
= 2 V p-p −82/−87 dBc
OUT
= 2 V p-p −72/−86 dBc
OUT
= 2 V p-p −71/−86 dBc
OUT
OUT
=
OUT
=
OUT
=
OUT
=
OUT
=
OUT
= 2 V p-p −69/−66 dBc
OUT
= 2 V p-p −56/−65 dBc
OUT
= 2 V p-p −58/−66 dBc
OUT
=
OUT
=
OUT
=
OUT
=
OUT
=
OUT
=
OUT
+46/−99 dBm/dBc
+46/−98 dBm/dBc
−74 dBc
−70 dBc
+35/−78 dBm/dBc
+35/−81 dBm/dBc
+37/−85 dBm/dBc
−73 dBc
−75 dBc
−72 dBc
AV = 12 dB 1.6 nV/√Hz
AV = 15.5 dB 1.48 nV/√Hz
Noise Figure (NF) AV = 6 dB 11.56 dB
AV = 12 dB 9.06 dB
AV = 15.5 dB 8.17 dB
Rev. | Page 8 of 28
Data Sheet ADL5565
Storage Temperature Range
−65°C to +150°C
B
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter Rating
Output Voltage Swing × Bandwidth Product 2000 V p-p MHz
Supply Voltage, VCC 5.25 V
VIPx, VINx VCC + 0.5 V
±I
Maximum 30 mA
OUT
Internal Power Dissipation 525 mW
Maximum Junction Temperature 125°C
Operating Temperature Range −40°C to +100°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL RESISTANCE
Table 4 lists the junction-to-air thermal resistance (θJA) and the
junction-to-paddle thermal resistance (θ
) for the ADL5565.
JC
Table 4. Thermal Resistance
Package Type θ
1
θ
JA
2
Unit
JC
16 LFCSP 60 12 °C/W
1
Measured on Analog Devices evaluation board. For more information about
board layout, see the Soldering Information and Recommended PCB Land
Pattern section.
2
Based on simulation with JEDEC standard JESD51.
ESD CAUTION
Rev. | Page 9 of 28
Loading...