ANALOG DEVICES ADIS16362 Service Manual
ADIS16362
TRIAXIS MEMS
ANGULAR RATE
SENSOR
SIGNAL
CONDITIONING
AND
CONVERSION
CALIBRATION
AND
DIGITAL
PROCESSING
DIGITAL
CONTROL
POWER
MANAGEMENT
OUTPUT
REGISTERS
AND SPI
INTERFACE
AUX_
ADC
AUX_
DAC
RST
CS
SCLK
DIN
DOUT
TRIAXIS MEMS
ACCELERATION
SENSOR
VCC
GND
DIO4/
CLKIN
SELF-TEST
ADIS16362
TEMPERATURE
SENSOR
ALARMS
DIO3DIO2
DIO1
08179-001
Six Degrees of Freedom Inertial Sensor
FEATURES
Tri axis digital gyroscope with digital range scaling
±75°/sec, ±150°/sec, ±300°/sec settings
Tight orthogonal alignment: <0.05°
Tri axis digital accelerometer: ±1.7 g
Wide sensor bandwidth: 330 Hz
Autonomous operation and data collection
No external configuration commands required
Start-up time: 180 ms
Sleep mode recovery time: 4 ms
Factory-calibrated sensitivity, bias, and axial alignment
Calibration temperature range: −20°C to +70°C
SPI-compatible serial interface
Embedded temperature sensor
Programmable operation and control
Automatic and manual bias correction controls
Bartlett window FIR filter length, number of taps
Digital I/O: data ready, alarm indicator, general-purpose
Alarms for condition monitoring
Sleep mode for power management
DAC output voltage
Enable external sample clock input: up to 1.2 kHz
Single-command self-test
Single-supply operation: 4.75 V to 5.25 V
2000 g shock survivability
Operating temperature range: −40°C to +105°C
FUNCTIONAL BLOCK DIAGRAM
Figure 1.
APPLICATIONS
Medical instrumentation
Robotics
Platform control
Navigation
GENERAL DESCRIPTION
The ADIS16362 iSensor® is a complete inertial system that includes
a triaxis gyroscope and triaxis accelerometer. Each sensor in the
ADIS16362 combines industry-leading iMEMS® technology
with signal conditioning that optimizes dynamic performance.
The factory calibration characterizes each sensor for sensitivity,
bias, alignment, and linear acceleration (gyro bias). As a result,
each sensor has its own dynamic compensation formulas that
provide accurate sensor measurements over a temperature
range of −20°C to +70°C.
The ADIS16362 provides a simple, cost-effective method for
integrating accurate, multiaxis, inertial sensing into industrial
systems, especially when compared with the complexity and
investment associated with discrete designs. All necessary
Rev. D
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patent s or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
motion testing and calibration are part of the production process
at the factory, greatly reducing system integration time. Tight
orthogonal alignment simplifies inertial frame alignment in
navigation systems. An improved SPI interface and register
structure provide faster data collection and configuration control.
The ADIS16362 uses a compatible pinout and the same package
as the ADIS1635x family. Therefore, systems that currently use
the ADIS1635x family can upgrade their performance with
minor firmware adjustments in their processor designs.
This compact module is approximately 23 mm × 23 mm × 23 mm
and provides a flexible connector interface that enables multiple
mounting orientation options.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113 ©2009–2011 Analog Devices, Inc. All rights reserved.
www.analog.com
Loading...