Analog Devices ADG715, ADG714 Datasheet

CMOS, Low Voltage

a

Serially-Controlled, Octal SPST Switches

FEATURES
ADG714 SPI™/QSPI™/MICROWIRE™-Compatible Interface
ADG715 I

2

C™-Compatible Interface

2.7 V to 5.5 V Single Supply
3 V Dual Supply

2.5  On Resistance

0.6  On Resistance Flatness
100 pA Leakage Currents
Octal SPST
Power-On Reset
Fast Switching Times
TTL/CMOS-Compatible
Small TSSOP Package

APPLICATIONS
Data Acquisition Systems
Communication Systems
Relay Replacement
Audio and Video Switching

GENERAL DESCRIPTION

The ADG714/ADG715 are CMOS, octal SPST (single-pole,
single-throw) switches controlled via either a two- or 3-wire
serial interface. On resistance is closely matched between switches
and very flat over the full signal range. Each switch conducts
equally well in both directions and the input signal range extends
to the supplies. Data is written to these devices in the form of
8 bits, each bit corresponding to one channel.

The ADG714 utilizes a 3-wire serial interface that is compatible
with SPI

, QSPI and MICROWIRE and most DSP interface
standards. The output of the shift register DOUT enables a
number of these parts to be daisy chained.

The ADG715 utilizes a 2-wire serial interface that is compatible
with the I

2

C interface standard. The ADG715 has four hard wired
addresses, selectable from two external address pins (A0 and A1).
This allows the 2 LSBs of the 7-bit slave address to be set by the
user. A maximum of four of these devices may be connected to
the bus.

ADG714/ADG715

FUNCTIONAL BLOCK DIAGRAMS

ADG714

S1

S1

S2

S3

S4

S5

S6

S7

S8

INPUT SHIFT

REGISTER

SCLK DIN SYNC RESET

D1

D2

D3

D4

D5

D6

D7

D8

DOUT

S2

S3

S4

S5

S6

S7

S8

On power-up of these devices, all switches are in the OFF con­dition, and the internal registers contain all zeros.

Low power consumption and operating supply range of 2.7 V to

5.5 V make this part ideal for many applications. These parts
may also be supplied from a dual ±3 V supply. The ADG714
and ADG715 are available in a small 24-lead TSSOP package.

PRODUCT HIGHLIGHTS

1. 2-3-Wire Serial Interface.

2. Single/Dual Supply Operation. The ADG714 and ADG715
are fully specified and guaranteed with 3 V, 5 V, and ±3 V
supply rails.

3. Low On Resistance, typically 2.5 Ω.

4. Low Leakage.

5. Power-On Reset.

6. Small 24-lead TSSOP package.

ADG715

INTERFACE

LOGIC

SDA SCL A0 A1

D1

D2

D3

D4

D5

D6

D7

D8

RESET

I2C is a trademark of Philips Corporation.
SPI and QSPI are trademarks of Motorola, Inc.
MICROWIRE is a trademark of National Semiconductor Corporation.

REV. 0

Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] World Wide Web Site: http://www.analog.com
Fax: [phone] © Analog Devices, Inc., 2000

1

ADG714/ADG715–SPECIFICATIONS

B Version

–40C

Parameter +25C to +85C Unit Test Conditions/Comments

ANALOG SWITCH

Analog Signal Range 0 V to V
On Resistance (R

On-Resistance Match Between Channels (∆R

On-Resistance Flatness (R

LEAKAGE CURRENTS V

Source OFF Leakage I

Drain OFF Leakage I

Channel ON Leakage I

DIGITAL INPUTS (SCLK, DIN, SYNC, A0, A1)

Input High Voltage, V
Input Low Voltage, V
Input Current, I

CIN, Digital Input Capacitance

DIGITAL OUTPUT ADG714 DOUT

Output Low Voltage 0.4 max I
C

Digital Output Capacitance 4 pF typ

OUT

DIGITAL INPUTS (SCL, SDA)

Input High Voltage, V

Input Low Voltage, V

IIN, Input Leakage Current 0.005 µA typ VIN = 0 V to V

, Input Hysteresis 0.05 V

V

HYST

CIN, Input Capacitance 6 pF typ

LOGIC OUTPUT (SDA)

VOL, Output Low Voltage 0.4 V max I

DYNAMIC CHARACTERISTICS

tON ADG714 20 ns typ VS = 3 V, RL = 300 Ω, CL = 35 pF

ADG715 95 ns typ VS = 3 V, RL = 300 Ω, CL = 35 pF

t

ON

ADG714 8 ns typ VS = 3 V, RL = 300 Ω, CL = 35 pF

t

OFF

ADG715 85 ns typ VS = 3 V, RL = 300 Ω, CL = 35 pF

t

OFF

Break-Before-Make Time Delay, t

Charge Injection ± 3 pC typ V
Off Isolation –60 dB typ

Channel-to-Channel Crosstalk –70 dB typ

–3 dB Bandwidth 155 MHz typ RL = 50 Ω, CL = 5 pF
CS (OFF) 11 pF typ

(OFF) 11 pF typ

C

D

CD, CS (ON) 22 pF typ

POWER REQUIREMENTS V

I

DD

NOTES

1

Temperature range is as follows: B Version: –40°C to +85°C.

2

Guaranteed by design, not subject to production test.

Specifications subject to change without notice.

)2.5Ω typ VS = 0 V to VDD, IS = 10 mA

ON

4.5 5 Ω max

)0.4Ω typ

ON

0.8 Ω max V

)0.6 Ω typ VS = 0 V to VDD, IS = 10 mA

FLAT(ON)

1.2 Ω max

(OFF) ± 0.01 nA typ VD = 4.5 V/1 V, VS = 1 V/4.5 V

S

± 0.1 ± 0.3 nA max

(OFF) ± 0.01 nA typ VD = 4.5 V/1 V, VS = 1 V/4.5 V

D

± 0.1 ± 0.3 nA max

, IS (ON) ± 0.01 nA typ VD = VS = 1 V, or 4.5 V

D

± 0.1 ± 0.3 nA max

2.4 V min

0.8 V max

± 0.1 µA max

0.7 V
V

DD

–0.3 V min

INL

or I

INH

INL

INH

INL

INH

0.005 µA typ VIN = V

2

2

2

3 pF typ

0.3 V

± 1 µA max

DD

2

0.6 V max I

2

32 ns max

140 ns max

15 ns max

130 ns max

D

8 ns typ VS = 3 V, RL = 300 Ω, CL = 35 pF

1 ns min

–80 dB typ R

–90 dB typ R

10 µA typ Digital Inputs = 0 V or 5.5 V

20 µA max

(VDD = 5 V  10%, VSS = 0 V, GND = 0 V unless otherwise noted)

V

DD

DD

V min

= 0 V to V

S

= 5.5 V

DD

INL

= 6 mA

SINK

DD

or V

INH

, IS = 10 mA

+ 0.3 V max

V max

DD

DD

V min

= 3 mA

SINK

= 6 mA

SINK

= 2 V, RS = 0 Ω, CL = 1 nF

S

RL = 50 Ω, CL = 5 pF, f = 10 MHz

= 50 Ω, CL = 5 pF, f = 1 MHz

L

RL = 50 Ω, CL = 5 pF, f = 10 MHz

= 50 Ω, CL = 5 pF, f = 1 MHz

L

= 5.5 V

DD

–2–

REV. 0

1

ADG714/ADG715

SPECIFICATIONS

Parameter +25C to +85C Unit Test Conditions/Comments

ANALOG SWITCH

Analog Signal Range 0 V to V
On Resistance (R

On-Resistance Match Between Channels (∆RON) 0.4 Ω typ VS = 0 V to V

On-Resistance Flatness (R

LEAKAGE CURRENTS V

Source OFF Leakage I

Drain OFF Leakage ID (OFF) ± 0.01 nA typ VS = 1 V/3 V, VD = 3 V/1 V

Channel ON Leakage I

DIGITAL INPUTS (SCLK, DIN, SYNC, A0, A1)

Input High Voltage, V
Input Low Voltage, V
Input Current, I

CIN, Digital Input Capacitance

DIGITAL OUTPUT ADG714 DOUT

Output Low Voltage 0.4 max I
C

Digital Output Capacitance 4 pF typ

OUT

DIGITAL INPUTS (SCL, SDA)

Input High Voltage, V

Input Low Voltage, V

I

, Input Leakage Current 0.005 µA typ VIN = 0 V to V

IN

V

, Input Hysteresis 0.05 V

HYST

CIN, Input Capacitance 6 pF typ

LOGIC OUTPUT (SDA)

VOL, Output Low Voltage 0.4 V max I

DYNAMIC CHARACTERISTICS

tON ADG714 35 ns typ VS = 2 V, RL = 300 Ω, CL = 35 pF

tON ADG715 130 ns typ VS = 2 V, RL = 300 Ω, CL = 35 pF

t

ADG714 11 ns typ VS = 2 V, RL = 300 Ω, CL = 35 pF

OFF

t

ADG715 115 ns typ VS = 2 V, RL = 300 Ω, CL = 35 pF

OFF

Break-Before-Make Time Delay, t

Charge Injection ± 2 pC typ VS = 1.5 V, RS = 0 Ω, CL = 1 nF
Off Isolation –60 dB typ

Channel-to-Channel Crosstalk –70 dB typ

–3 dB Bandwidth 155 MHz typ RL = 50 Ω, CL = 5 pF

(OFF) 11 pF typ

C

S

C

(OFF) 11 pF typ

D

CD, CS (ON) 22 pF typ

POWER REQUIREMENTS V

I

DD

NOTES

1

Temperature range is as follows: B Version: –40°C to +85°C.

2

Guaranteed by design, not subject to production test.

Specifications subject to change without notice.

)6Ω typ VS = 0 V to VDD, IS = 10 mA

ON

FLAT(ON)

(OFF) ± 0.01 nA typ VS = 3 V/1 V, VD = 1 V/3 V

S

, IS (ON) ± 0.01 nA typ VS = VD = 1 V, or 3 V

D

INH

INL

or I

INL

INH

INH

INL

2

(VDD = 3 V  10%, VSS = 0 V, GND = 0 V unless otherwise noted)

B Version

11 12 Ω max

) 3.5 Ω typ VS = 0 V to VDD, IS = 10 mA

± 0.1 ± 0.3 nA max

± 0.1 ± 0.3 nA max

± 0.1 ± 0.3 nA max

0.005 µA typ VIN = V

2

2

2

2

D

3 pF typ

8 ns typ VS = 2 V, RL = 300 Ω, CL = 35 pF

–80 dB typ R

–90 dB typ R

10 µA typ Digital Inputs = 0 V or 3.3 V

–40C

V

DD

1.2 Ω max

2.0 V min

0.4 V max

± 0.1 µA max

0.7 V
+ 0.3 V max

V

DD

DD

V min

–0.3 V min

DD

V max

0.3 V

± 1 µA max

DD

V min

0.6 V max I

65 ns max

200 ns max

20 ns max

180 ns max

1 ns min

20 µA max

, IS = 10 mA

DD

= 3.3 V

DD

or V

INL

INH

= 6 mA

SINK

DD

= 3 mA

SINK

= 6 mA

SINK

RL = 50 Ω, CL = 5 pF, f = 10 MHz

= 50 Ω, CL = 5 pF, f = 1 MHz

L

RL = 50 Ω, CL = 5 pF, f = 10 MHz

= 50 Ω, CL = 5 pF, f = 1 MHz

L

= 3.3 V

DD

REV. 0

–3–

ADG714/ADG715–SPECIFICATIONS

1

DUAL SUPPLY

Parameter +25C to +85C Unit Test Conditions/Comments

ANALOG SWITCH

Analog Signal Range V
On Resistance (R

On-Resistance Match Between Channels (∆R

On-Resistance Flatness (R

LEAKAGE CURRENTS V

Source OFF Leakage I

Drain OFF Leakage I

Channel ON Leakage I

DIGITAL INPUTS

Input High Voltage, V
Input Low Voltage, V
Input Current, I

CIN, Digital Input Capacitance

DIGITAL OUTPUT ADG714 DOUT

Output Low Voltage 0.4 max

C

Digital Output Capacitance 4 pF typ

OUT

DIGITAL INPUTS (SCL, SDA)

Input High Voltage, V

Input Low Voltage, V

I

, Input Leakage Current 0.005 µA typ VIN = 0 V to V

IN

V

, Input Hysteresis 0.05 V

HYST

CIN, Input Capacitance 6 pF typ

LOGIC OUTPUT (SDA)

VOL, Output Low Voltage 0.4 V max I

DYNAMIC CHARACTERISTICS

tON ADG714 20 ns typ VS = 1.5 V, RL = 300 Ω, CL = 35 pF

t

ADG715 133 ns typ VS = 1.5 V, RL = 300 Ω, CL = 35 pF

ON

t

ADG714 8 ns typ VS = 1.5 V, RL = 300 Ω, CL = 35 pF

OFF

t

ADG715 124 ns typ VS = 1.5 V, RL = 300 Ω, CL = 35 pF

OFF

Break-Before-Make Time Delay, t

Charge Injection ± 3 pC typ V
Off Isolation –60 dB typ

Channel-to-Channel Crosstalk –70 dB typ

–3 dB Bandwidth 155 MHz typ RL = 50 Ω, CL = 5 pF
C

(OFF) 11 pF typ

S

C

(OFF) 11 pF typ

D

CD, CS (ON) 22 pF typ

POWER REQUIREMENTS V

I

DD

I

SS

NOTES

1

Temperature range is as follows: B Version: –40°C to +85°C.

2

Guaranteed by design, not subject to production test.

Specifications subject to change without notice.

(VDD = +3 V  10%, VSS = 3 V  GND = 0 V unless otherwise noted)

B Version

) 2.5 Ω typ VS = VSS to VDD, IDS = 10 mA

ON

4.5 5 Ω max

) 0.4 Ω typ VS = VSS to VDD, IDS = 10 mA

ON

) 0.6 Ω typ VS = VSS to VDD, IDS = 10 mA

FLAT(ON)

(OFF) ± 0.01 nA typ VS = +2.25 V/–1.25 V, VD = –1.25 V/+2.25 V

S

± 0.1 ± 0.3 nA max

(OFF) ± 0.01 nA typ VS = +2.25 V/–1.25 V, VD = –1.25 V/+2.25 V

D

± 0.1 ± 0.3 nA max

, IS (ON) ± 0.01 nA typ VS = VD = +2.25 V/–1.25 V

D

± 0.1 ± 0.3 nA max

INH

INL

INL

or I

INH

2

2

2

INH

INL

2

2

D

0.005 µA typ VIN = V

3 pF typ

8 ns typ VS = 1.5 V, RL = 300 Ω, CL = 35 pF

–80 dB typ R

–90 dB typ R

15 µA typ Digital Inputs = 0 V or 3.3 V

15 µA typ

–40C

to VDDV

SS

0.8 Ω max

1 Ω max

2.0 V min

0.4 V max

± 0.1 µA max

0.7 V
V

+ 0.3 V max

DD

DD

V min

–0.3 V min

0.3 V

DD

V max

± 1 µA max

DD

V min

0.6 V max I

32 ns max

200 ns max

18 ns max

190 ns max

1 ns min

25 µA max

25 µA max

= +3.3 V, VSS = –3.3 V

DD

or V

INL

INH

I

= 6 mA

SINK

DD

= 3 mA

SINK

= 6 mA

SINK

= 0 V, RS = 0 Ω, CL = 1 nF

S

RL = 50 Ω, CL = 5 pF, f = 10 MHz

= 50 Ω, CL = 5 pF, f = 1 MHz

L

RL = 50 Ω, CL = 5 pF, f = 10 MHz

= 50 Ω, CL = 5 pF, f = 1 MHz

L

= +3.3 V, VSS = –3.3 V

DD

–4–

REV. 0

ADG714/ADG715

ADG714 TIMING CHARACTERISTICS

Parameter Limit at T

f

SCLK

t

1

t

2

t

3

t

4

t

5

t

6

t

7

t

8

3

t

9

NOTES

1

See Figure 1.

2

All input signals are specified with tr = tf = 5 ns (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2.

3

CL = 20 pF, RL = 1 kΩ.

Specifications subject to change without notice.

30 MHz max SCLK Cycle Frequency
33 ns min SCLK Cycle Time
13 ns min SCLK High Time
13 ns min SCLK Low Time
0 ns min SYNC to SCLK Rising Edge Setup Time
5 ns min Data Setup Time

4.5 ns min Data Hold Time
0 ns min SCLK Falling Edge to SYNC Rising Edge
33 ns min Minimum SYNC High Time
20 ns min SCLK Rising Edge to DOUT Valid

SCLK

SYNC

DIN

DOUT

t

8

, T

MIN

DB71DB6

t

4

t

MAX

9

t

5

1, 2

(VDD = 2.7 V to 5.5 V. All specifications –40C to +85C unless otherwise noted.)

Unit Conditions/Comments

t

1

t

t

2

t

6

1

DB21DB11DB0

3

t

7

DB0DB7

1

NOTE

1

DATA FROM PREVIOUS WRITE CYCLE

Figure 1. 3-Wire Serial Interface Timing Diagram

REV. 0

–5–