ANALOG DEVICES ADG5436 Service Manual

High Voltage Latch-Up Proof,

FEATURES

Latch-up proof
8 kV HBM ESD rating
Low on resistance (<10 Ω)
±9 V to ±22 V dual-supply operation
9 V to 40 V single-supply operation
48 V supply maximum ratings
Fully specified at ±15 V, ±20 V, +12 V, and +36 V
V

to VDD analog signal range

SS

APPLICATIONS

Relay replacement
Automatic test equipment
Data acquisition
Instrumentation
Avio nics
Audio and video switching
Communication systems

Dual SPDT Switches

ADG5436

FUNCTIONAL BLOCK DIAGRAMS

S1A

S1B

IN1

IN2

S2A

S2B

SWITCHES SHOWN FOR A LOGIC 1 I NP UT.

S1A

D1

S1B

ADG5436

Figure 1. TSSOP Package

ADG5436

D1

D2

S2A
D2
S2B

09204-001

GENERAL DESCRIPTION

The ADG5436 is a monolithic CMOS device containing two
independently selectable single-pole/single-throw (SPDT)
switches. An EN input on the LFCSP package enables or
disables the device. When disabled, all channels switch off. Each
switch conducts equally well in both directions when on and
has an input signal range that extends to the supplies. In the off
condition, signal levels up to the supplies are blocked. Both
switches exhibit break-before-make switching action for use in
multiplexer applications.

The on-resistance profile is very flat over the full analog input
range, ensuring excellent linearity and low distortion when
switching audio signals.

LOGIC

IN2 ENIN1

SWITCHES S HO WN FOR A LOGIC 1 INPUT.

Figure 2. LFCSP Package

09204-002

PRODUCT HIGHLIGHTS

1. Trench isolation guards against latch-up. A dielectric trench

separates the P and N channel transistors thereby preventing
latch-up even under severe overvoltage conditions.

2. Low R

3. Dual-supply operation. For applications where the analog

signal is bipolar, the ADG5436 can be operated from dual
supplies up to ±22 V.

4. Single-supply operation. For applications where the analog

signal is unipolar, the ADG5436 can be operated from a
single-rail power supply up to 40 V.

5. 3 V logic compatible digital inputs: V

6. No V

.

ON

logic power supply required.

L

= 2.0 V, V

INH

= 0.8 V.

INL

Rev. A

Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] www.analog.com
Fax: [phone] ©2010–2011 Analog Devices, Inc. All rights reserved.

ADG5436

TABLE OF CONTENTS

Features .............................................................................................. 1

Applications ....................................................................................... 1

Functional Block Diagrams ............................................................. 1

General Description ......................................................................... 1

Product Highlights ........................................................................... 1

Revision History ............................................................................... 2

Specifications ..................................................................................... 3

±15 V Dual Supply ....................................................................... 3

±20 V Dual Supply ....................................................................... 4

12 V Single Supply ........................................................................ 5

36 V Single Supply ........................................................................ 6

Continuous Current per Channel, Sx or Dx ............................. 7

REVISION HISTORY

6/11—Rev. 0 to Rev. A

Added I

Updated Outline Dimensions ....................................................... 19

Changes to Ordering Guide .......................................................... 19

7/10—Revision 0: Initial Version

−40°C to +125°C Parameter .......................................... 5

SS

Absolute Maximum Ratings ............................................................8

ESD Caution...................................................................................8

Pin Configurations and Function Descriptions ............................9

Truth Table For Switches ..............................................................9

Typical Performance Characteristics ........................................... 10

Test Circuits ..................................................................................... 14

Terminology .................................................................................... 16

Trench Isolation .............................................................................. 17

Applications Information .............................................................. 18

Outline Dimensions ....................................................................... 19

Ordering Guide .......................................................................... 19

Rev. A | Page 2 of 20

ADG5436

SPECIFICATIONS

±15 V DUAL SUPPLY

VDD = +15 V ± 10%, VSS = −15 V ± 10%, GND = 0 V, unless otherwise noted.

Table 1.

Parameter 25°C −40°C to +85°C −40°C to +125°C Unit Test Conditions/Comments

ANALOG SWITCH

Analog Signal Range VDD to VSS V
On Resistance, RON 9.8 Ω typ VS = ±10 V, IS = −10 mA; see Figure 25
11 14 16 Ω max VDD = +13.5 V, VSS = −13.5 V
On-Resistance Match

Between Channels, ∆R

ON

0.35 Ω typ V

0.7 0.9 1.1 Ω max
On-Resistance Flatness, R

1.2 Ω typ VS = ±10 V, IS = −10 mA

FL AT (ON)

1.6 2 2.2 Ω max

LEAKAGE CURRENTS

Source Off Leakage, IS (Off )

Drain Off Leakage, ID (Off )

Channel On Leakage, ID (On), IS (On)

DIGITAL INPUTS

Input High Voltage, V
Input Low Voltage, V
Input Current, I

INL

2.0 V min

INH

0.8 V max

INL

or I

0.002 µA typ VIN = V

INH

±0.05
±0.25 ±0.75 ±3.5
±0.1
±0.4 ±2 ±12
±0.1
±0.4 ±2 ±12

VDD = +16.5 V, VSS = −16.5 V
nA typ
nA max
nA typ
nA max
nA typ VS = VD = ±10 V; see Figure 24
nA max

±0.1 µA max
Digital Input Capacitance, CIN 5 pF typ

DYNAMIC CHARACTERISTICS1

Transition Time, t

170 ns typ RL = 300 Ω, CL = 35 pF

TRANSITION

235 285 316 ns max VS = 10 V; see Figure 31
tON 173 ns typ RL = 300 Ω, CL = 35 pF
230 280 351 ns max VS = 10 V; see Figure 33
t

124 ns typ RL = 300 Ω, CL = 35 pF

OFF

160 193 218 ns max VS = 10 V; see Figure 33
Break-Before-Make Time Delay, tD 55 ns typ RL = 300 Ω, CL = 35 pF

18 ns min VS1 = VS2 = 10 V; see Figure 32

Charge Injection, Q

200 pC typ VS = 0 V, RS = 0 Ω, CL = 1 nF;

INJ

Off Isolation −78 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz;

Channel-to-Channel Crosstalk −58 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz;

Total Harmonic Distortion + Noise 0.009 % typ RL = 1 kΩ, 15 V p-p, f = 20 Hz to 20 kHz;

−3 dB Bandwidth 102 MHz typ RL = 50 Ω, CL = 5 pF; see Figure 30
Insertion Loss −0.7 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz;

CS (Off ) 18 pF typ VS = 0 V, f = 1 MHz
CD (Off ) 62 pF typ VS = 0 V, f = 1 MHz
CD (On), CS (On) 83 pF typ VS = 0 V, f = 1 MHz

= ±10 V , IS = −10 mA

S

V

= ±10 V, VD = 10 V; see Figure 28

S

V

= ±10 V, VD = 10 V; see Figure 28

S

or VDD

GND

see Figure 34

see Figure 27

see Figure 26

see Figure 29

see Figure 30

Rev. A | Page 3 of 20

ADG5436

Parameter 25°C −40°C to +85°C −40°C to +125°C Unit Test Conditions/Comments

POWER REQUIREMENTS VDD = +16.5 V, VSS = −16.5 V

IDD

ISS

VDD/VSS ±9/±22 V min/V max GND = 0 V

1

Guaranteed by design; not subject to production test.

±20 V DUAL SUPPLY

VDD = +20 V ± 10%, VSS = −20 V ± 10%, GND = 0 V, unless otherwise noted.

Table 2.

Parameter 25°C −40°C to +85°C −40°C to +125°C Unit Test Conditions/Comments

ANALOG SWITCH

Analog Signal Range VDD to VSS V
On Resistance, RON

On-Resistance Match

Between Channels, ∆R

On-Resistance Flatness, R

LEAKAGE CURRENTS

Source Off Leakage, IS (Off )

Drain Off Leakage, ID (Off )

Channel On Leakage, ID (On), IS (On)

DIGITAL INPUTS

Input High Voltage, V
Input Low Voltage, V
Input Current, I

or I

INL

±0.1 µA max
Digital Input Capacitance, CIN 5 pF typ

DYNAMIC CHARACTERISTICS1

Transition Time, t

TRANSITION

217 260 293 ns max VS = 10 V; see Figure 31
tON 164 ns typ RL = 300 Ω, CL = 35 pF
213 256 287 ns max VS = 10 V; see Figure 33
t

110 ns typ RL = 300 Ω, CL = 35 pF

OFF

152 173 194 ns max VS = 10 V; see Figure 33
Break-Before-Make Time Delay, tD 50 ns typ RL = 300 Ω, CL = 35 pF

15 ns min VS1 = VS2 = 10 V; see Figure 32

Charge Injection, Q

Off Isolation −78 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz;

Channel-to-Channel Crosstalk −58 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz;

Total Harmonic Distortion + Noise 0.007 % typ RL = 1 kΩ, 20 V p-p, f = 20 Hz to 20 kHz;

−3 dB Bandwidth 100 MHz typ RL = 50 Ω, CL = 5 pF; see Figure 30

ON

FL AT (ON)

2.0 V min

INH

0.8 V max

INL

0.002 µA typ VIN = V

INH

158 ns typ RL = 300 Ω, CL = 35 pF

250 pC typ VS = 0 V, RS = 0 Ω, CL = 1 nF; see

INJ

45
55 70

0.001
1

9
10 13 15

0.35

0.7 0.9 1.1

1.5

1.8 2.2 2.5

±0.05
±0.25 ±0.75 ±3.5
±0.1
±0.4 ±2 ±12
±0.1
±0.4 ±2 ±12

µA typ Digital inputs = 0 V or VDD
µA max
µA typ Digital inputs = 0 V or VDD
µA max

Ω typ VS = ±15 V, IS = −10 mA; see Figure 25
Ω max VDD = +18 V, VSS = −18 V
Ω typ VS = ±15 V , IS = −10 mA

Ω max
Ω typ VS = ±15 V, IS = −10 mA
Ω max
VDD = +22 V, VSS = −22 V
nA typ

V

= ±15 V, VD = 15 V; see Figure 28

S

nA max
nA typ

V

= ±15 V, VD = 15 V; see Figure 28

S

nA max
nA typ VS = VD = ±15 V; see Figure 24
nA max

or VDD

GND

Figure 34

see Figure 27

see Figure 26

see Figure 29

Rev. A | Page 4 of 20

ADG5436

Parameter 25°C −40°C to +85°C −40°C to +125°C Unit Test Conditions/Comments

Insertion Loss −0.6 dB typ

CS (Off) 18 pF typ VS = 0 V, f = 1 MHz
CD (Off) 63 pF typ VS = 0 V, f = 1 MHz
CD (On), CS (On) 82 pF typ VS = 0 V, f = 1 MHz

POWER REQUIREMENTS VDD = +22 V, VSS = −22 V

IDD

ISS

50
70 110

0.001
1

μA typ Digital inputs = 0 V or VDD
μA max
μA typ Digital inputs = 0 V or VDD
μA max

VDD/VSS ±9/±22 V min/V max GND = 0 V

1

Guaranteed by design; not subject to production test.

12 V SINGLE SUPPLY

VDD = 12 V ± 10%, VSS = 0 V, GND = 0 V, unless otherwise noted.

Table 3.

Parameter 25°C −40°C to +85°C −40°C to +125°C Unit Test Conditions/Comments

ANALOG SWITCH

Analog Signal Range 0 V to VDD V
On Resistance, RON

On-Resistance Match

Between Channels, ∆R

ON

On-Resistance Flatness, R

FLAT (ON)

LEAKAGE CURRENTS

Source Off Leakage, IS (Off)

Drain Off Leakage, ID (Off)

Channel On Leakage, ID (On), IS (On)

DIGITAL INPUTS

Input High Voltage, V
Input Low Voltage, V
Input Current, I

INL

2.0 V min

INH

0.8 V max

INL

or I

0.002 μA typ VIN = V

INH

±0.1 μA max
Digital Input Capacitance, CIN 5 pF typ

DYNAMIC CHARACTERISTICS1

Transition Time, t

250 ns typ RL = 300 Ω, CL = 35 pF

TRANSITION

346 437 501 ns max VS = 8 V; see Figure 31
tON 250 ns typ RL = 300 Ω, CL = 35 pF
358 445 512 ns max VS = 8 V; see Figure 33
t

135 ns typ RL = 300 Ω, CL = 35 pF

OFF

178 212 237 ns max VS = 8 V; see Figure 33
Break-Before-Make Time Delay, tD 125 ns typ RL = 300 Ω, CL = 35 pF

50 ns min VS1 = VS2 = 8 V; see Figure 32

Charge Injection, Q

80 pC typ

INJ

19

22 27 31

0.4

0.8 1 1.2

4.4

5.5 6.5 7.5

±0.05

±0.25 ±0.75 ±3.5
±0.1

±0.4 ±2 ±12
±0.1
±0.4 ±2 ±12

Ω typ

Ω max VDD = 10.8 V, VSS = 0 V
Ω typ VS = 0 V to 10 V, IS = −10 mA

Ω max
Ω typ VS = 0 V to 10 V, IS = −10 mA
Ω max
V
nA typ

nA max
nA typ

nA max
nA typ VS = VD = 1 V/10 V; see Figure 24
nA max

Rev. A | Page 5 of 20

= 50 Ω, CL = 5 pF, f = 1 MHz;

R

L

see Figure 30

= 0 V to 10 V, IS = −10 mA; see

V

S

Figure 25

= 13.2 V, VSS = 0 V

DD

= 1 V/10 V, VD = 10 V/1 V;

V

S

see Figure 28

= 1 V/10 V, VD = 10 V/1 V;

V

S

see Figure 28

or VDD

GND

= 6 V, RS = 0 Ω, CL = 1 nF; see

V

S

Figure 34

ADG5436

Parameter 25°C −40°C to +85°C −40°C to +125°C Unit Test Conditions/Comments

Off Isolation −78 dB typ

Channel-to-Channel Crosstalk −58 dB typ

Total Harmonic Distortion + Noise 0.075 % typ

−3 dB Bandwidth 106 MHz typ RL = 50 Ω, CL = 5 pF; see Figure 30
Insertion Loss −1.3 dB typ

CS (Off) 22 pF typ VS = 6 V, f = 1 MHz
CD (Off) 67 pF typ VS = 6 V, f = 1 MHz
CD (On), CS (On) 85 pF typ VS = 6 V, f = 1 MHz

POWER REQUIREMENTS VDD = 13.2 V

IDD

40
50 65

μA typ Digital inputs = 0 V or VDD
μA max

VDD 9/40 V min/V max GND = 0 V, VSS = 0 V

1

Guaranteed by design; not subject to production test.

36 V SINGLE SUPPLY

VDD = 36 V ± 10%, VSS = 0 V, GND = 0 V, unless otherwise noted.

= 50 Ω, CL = 5 pF, f = 1 MHz;

R

L

see Figure 27

= 50 Ω, CL = 5 pF, f = 1 MHz;

R

L

see Figure 26

= 1 kΩ, 6 V p-p, f = 20 Hz to 20 kHz;

R

L

see Figure 29

= 50 Ω, CL = 5 pF, f = 1 MHz;

R

L

see Figure 30

Table 4.

Parameter 25°C −40°C to +85°C −40°C to +125°C Unit Test Conditions/Comments

ANALOG SWITCH

Analog Signal Range 0 V to VDD V
On Resistance, RON

10.6

Ω typ

= 0 V to 30 V, IS = −10 mA;

V

S

see Figure 25

On-Resistance Match

Between Channels, ∆R

On-Resistance Flatness, R

LEAKAGE CURRENTS

Source Off Leakage, IS (Off)

ON

FLAT(ON)

12 15 17

0.35

0.7 0.9 1.1

2.7

3.2 3.8 4.5

±0.05

Ω max VDD = 32.4 V, VSS = 0 V
Ω typ VS = 0 V to 30 V, IS = −10 mA

Ω max
Ω typ VS = 0 V to 30 V, IS = −10 mA
Ω max
V
nA typ

= 39.6 V, VSS = 0 V

DD

= 1 V/30 V, VD = 30 V/1 V;

V

S

see Figure 28

Drain Off Leakage, ID (Off)

±0.25 ±0.75 ±3.5
±0.1

nA max
nA typ

= 1 V/30 V, VD = 30 V/1 V;

V

S

see Figure 28

Channel On Leakage, ID (On), IS (On)

±0.4 ±2 ±12
±0.1
±0.4 ±2 ±12

nA max
nA typ VS = VD = 1 V/30 V; see Figure 24
nA max

DIGITAL INPUTS

Input High Voltage, V
Input Low Voltage, V
Input Current, I

INL

2.0 V min

INH

0.8 V max

INL

or I

0.002 μA typ VIN = V

INH

GND

or VDD
±0.1 μA max
Digital Input Capacitance, CIN 5 pF typ

DYNAMIC CHARACTERISTICS1

Transition Time, t

174 ns typ RL = 300 Ω, CL = 35 pF

TRANSITION

246 270 303 ns max VS = 18 V; see Figure 31
tON 180 ns typ RL = 300 Ω, CL = 35 pF
247 270 301 ns max VS = 18 V; see Figure 33

Rev. A | Page 6 of 20