Datasheet ADG467BR, ADG467BN, ADG466BRS, ADG466BRM, ADG466BN Datasheet (Analog Devices)

REV. A

Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.

a

ADG466/ADG467

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] World Wide Web Site: http://www.analog.com
Fax: [phone] © Analog Devices, Inc., 1998

Triple and Octal

Channel Protectors

FUNCTIONAL BLOCK DIAGRAMS

ADG466

ADG467

V

D1

V

D2

V

D3

V

S1

V

S2

V

S3

V

D1

V

D2

V

D3

V

D8

V

S1

V

S2

V

S3

V

S8

VDDV

SS

VDDV

SS

V

IN

V

DD

V

DD

V

IN

V

OUT

OUTPUT CLAMPED
@ V

DD

– 1.5V

V

OUT

GENERAL DESCRIPTION

The ADG466 and ADG467 are triple and octal channel pro­tectors, respectively. The channel protector is placed in series
with the signal path. The channel protector will protect sensitive
components from voltage transience in the signal path whether
the power supplies are present or not. Because the channel
protection works whether the supplies are present or not, the
channel protectors are ideal for use in applications where
correct power sequencing can’t always be guaranteed (e.g., hot­insertion rack systems) to protect analog inputs. This is dis­cussed further, and some example circuits are given in the
Applications section of this data sheet.

Each channel protector has an independent operation and con­sists of an n-channel MOSFET, a p-channel MOSFET and an
n-channel MOSFET, connected in series. The channel protec­tor behaves just like a series resistor during normal operation,
i.e., (V

SS

+ 2 V) < VIN < (V

DD

– 1.5 V). When a channel’s ana-

log input exceeds the power supplies (including V

DD

and VSS =
0 V), one of the MOSFETs will switch off, clamping the output
to either V

SS

+ 2 V or VDD – 1.5 V. Circuitry and signal source
protection is provided in the event of an overvoltage or power
loss. The channel protectors can withstand overvoltage inputs
from –40 V to +40 V. See the Circuit Information section of
this data sheet.

The ADG466 and ADG467 can operate off both bipolar and
unipolar supplies. The channels are normally on when power is
connected and open circuit when power is disconnected. With

power supplies of ± 15 V, the on-resistance of the ADG466 and

FEATURES
Fault and Overvoltage Protection up to 640 V

Signal Paths Open Circuit with Power Off
Signal Path Resistance of R

ON

with Power On
44 V Supply Maximum Ratings
Low On Resistance

ADG466/ADG467 60 V typ
1 nA Max Path Current Leakage @ +258C
Low R

ON

Match (5 V max)
Low Power Dissipation 0.8 mW typ
Latch-Up Proof Construction

APPLICATIONS
ATE Equipment
Sensitive Measurement Equipment
Hot-Insertion Rack Systems

ADG467 is 60 Ω typ with a leakage current of ±1 nA max.

When power is disconnected, the input leakage current is ap-

proximately ±5 nA typ.
The ADG466 is available in 8-lead DIP, SOIC and µSOIC

packages. The ADG467 is available in an 18-lead SOIC package
and a 20-lead SSOP package.

PRODUCT HIGHLIGHTS

1. Fault Protection.
The ADG466 and ADG467 can withstand continuous volt­age inputs from –40 V to +40 V. When a fault occurs due to
the power supplies being turned off or due to an overvoltage
being applied to the ADG466 and ADG467, the output is
clamped. When power is turned off, current is limited to the
microampere level.

2. Low Power Dissipation.

3. Low R

ON

.

ADG466/ADG467 60 Ω typ.

4. Trench Isolation Latch-Up Proof Construction.
A dielectric trench separates the p- and n-channel MOSFETs
thereby preventing latch-up.

–2–

REV. A

ADG466/ADG467–SPECIFICATIONS

Dual Supply

1

ADG466 ADG467

Parameter +258CB

1

+258CB

1

Units Test Conditions/Comments

FAULT PROTECTED CHANNEL

Fault-Free Analog Signal Range

2

VSS + 1.2 VSS + 1.2 V min Output Open Circuit
V

DD

– 0.8 VDD – 0.8 V max

R

ON

60 75 62 80 Ω typ –10 V ≤ VS ≤ +10 V, I

S

= 1 mA

80 95 Ω max

∆R

ON

34 6 Ω max –5 V ≤ VS ≤ +5 V

R

ON

Match 4 6 5 6 Ω max VS = ±10 V, I

S

= 1 mA

LEAKAGE CURRENTS

Channel Output Leakage, I

S(ON)

VS = V

D

= ±10 V

(without Fault Condition) ±0.1 ±1 ±0.04 ±0.2 nA typ

±1 ±5 ±1 ±5 nA max

Channel Input Leakage, I

D(ON)

V

S

= ±25 V

(with Fault Condition) ±0.2 ±0.4 ±0.2 ±0.4 nA typ V

D

= Open Circuit

±2 ±5 ±2 ±5 nA max

Channel Input Leakage, I

D(OFF)

VDD = 0 V, V

SS

= 0 V

(with Power Off and Fault) ±0.5 ±2 ±0.5 ±2 nA typ V

S

= ±35 V,

±1 ±5 ±2 ±10 nA max V

D

= Open Circuit

Channel Input Leakage, I

D(OFF)

VDD = 0 V, V

SS

= 0 V

(with Power Off and Output S/C) ±0.005 ±0.1 ±0.006 ±0.16 µA typ V

S

= ±35 V, V

D

= 0 V

±0.015 ±0.5 ±0.015 ±0.5 µA max

POWER REQUIREMENTS

I

DD

±0.05 ±0.05 µA typ
±0.5 ±8 ±0.5 ±8 µA max

I

SS

±0.05 ±0.05 µA typ
±0.5 ±8 ±0.5 ±8 µA max

V

DD/VSS

0 0 0 0 V min

±20 ±20 ±20 ±20 V max

NOTES

1

Temperature range is as follows: B Version: – 40°C to +85°C.

2

Guaranteed by design, not subject to production test.

Specifications subject to change without notice.

(VDD = +15 V, VSS = –15 V, GND = 0 V, unless otherwise noted)

ADG466/ADG467

–3–

REV. A

ABSOLUTE MAXIMUM RATINGS

1

(T

A

= +25°C unless otherwise noted)

VDD to VSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +44 V

V

S

, VD, Analog Input Overvoltage with Power ON

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . VSS – 20 V to VDD + 20 V

V

S

, VD, Analog Input Overvoltage with Power OFF

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .–35 V to +35 V

Continuous Current, S or D . . . . . . . . . . . . . . . . . . . . . 20 mA

Peak Current, S or D . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mA

(Pulsed at 1 ms, 10% Duty Cycle Max)

Operating Temperature Range

Industrial (B Version) . . . . . . . . . . . . . . . . . –40°C to +85°C

Storage Temperature Range . . . . . . . . . . . . . –65°C to +125°C

Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . +150°C

Plastic DIP Package

θ

JA

, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 125°C/W

Lead Temperature, Soldering (10 sec) . . . . . . . . . . . +260°C

SOIC Package

θ

JA

, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 160°C/W

Lead Temperature, Soldering

Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . +215°C

Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C

µSOIC Package

θ

JA

, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 160°C/W

Lead Temperature, Soldering

Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . +215°C

Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C

SSOP Package

θ

JA

, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 130°C/W

Lead Temperature, Soldering

Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . +215°C

Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C

NOTES

1

Stresses above those listed under Absolute Maximum Ratings may cause perma-

nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute maximum rating condi­tions for extended periods may affect device reliability. Only one absolute maxi­mum rating may be applied at any one time.

2

Overvoltages at S or D will be clamped by the channel protector, see Circuit

Information section of the data sheet.

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the ADG466/ADG467 features proprietary ESD protection circuitry, permanent
damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper
ESD precautions are recommended to avoid performance degradation or loss of functionality.

PIN CONFIGURATIONS

8-Lead

DIP, SOIC 18-Lead
and mSOIC SOIC

1
2
3
4

8
7
6
5

TOP VIEW

(Not to Scale)

ADG466

V

D1

V

S3

V

S2

V

S1

V

DD

V

D2

V

D3

V

SS

14
13
12
11

17
16
15

18

10

9

8

1
2
3
4

7

6

5

TOP VIEW

(Not to Scale)

ADG467

V

D1

V

S3

V

S2

V

S1

V

DD

V

D2

V

D3

V

D4

V

S6

V

S5

V

S4

V

D5

V

D6

V

D7

V

D8

V

SS

V

S8

V

S7

20-Lead

SSOP

V

D1

V

S3

V

S2

V

S1

V

DD

V

D2

V

D3

V

D4

V

S6

V

S5

V

S4

V

D5

V

D6

V

D7

V

D8

V

SS

V

S8

V

S7

14
13
12
11

17
16
15

20
19
18

10

9

8

1
2
3
4

7

6

5

TOP VIEW

(Not to Scale)

ADG467

NC = NO CONNECT

NC

NC

ORDERING GUIDE

Model Temperature Range Package Description Package Options

ADG466BN –40°C to +85°C 8-Lead Plastic DIP N-8
ADG466BR –40°C to +85°C 8-Lead Small Outline Package SO-8
ADG466BRM –40°C to +85°C 8-Lead Micro Small Outline Package RM-8

ADG467BR –40°C to +85°C 18-Lead Small Outline Package R-18
ADG467BRS –40°C to +85°C 20-Lead Shrink Small Outline Package RS-20

WARNING!

ESD SENSITIVE DEVICE

ADG466/ADG467–Typical Performance Characteristics

–4–

REV. A

ADG466

VD – Volts

R

ON

–

V

80
75

30

–10 10–5 0 5

60

45
40
35

70
65

50

55

VDD, VSS =65V

VDD, VSS =610V

616.5V

VDD, VSS =613.5V

VDD, VSS =615V

Figure 1. On Resistance as a Function of VDD and V

D

(Input Voltage)

70

65

25

–10 10–5 0 5

50

40

35

30

60

55

45

1258C

858C

258C

–408C

V

D

– Volts

R

ON

– V

VDD = +15V

VSS

= –15V

Figure 2. On Resistance as a Function of Temperature
and V

D

(Input Voltage)

616.5V

ADG467

VD – Volts

105

95

45

–10 10–5

R

ON

– V

05

85

75

65

55

65V

615V

613.5V

610V

Figure 3. On Resistance as a Function of VDD and V

D

(Input Voltage)

Ch1

10V

500mV5.00V Ch2 5.00V M50.0ns Ch1

0V

–5V

15V

5V

–5V TO +15V STEP INPUT

CHANNEL PROTECTOR

OUTPUT

POSITIVE OVERVOLTAGE
R

LOAD

= 100kV

ON INPUT

C

LOAD

= 100pF
VDD = +10V
VSS = –10V

Figure 4. Positive Overvoltage Transience Response

Ch2 500mVCh1 5.00V 5.00V M50.0ns Ch1

NEGATIVE OVERVOLTAGE

ON INPUT

R

LOAD

= 100kV

C

LOAD

= 100pF

V

DD

= +10V

V

SS

= –10V

CHANNEL PROTECTOR

OUTPUT

5V TO –15V STEP INPUT

–10V

5V

0V

–5V

–15V

Figure 5. Negative Overvoltage Transience Response

1

500mV5.00V Ch2 5.00V M100ms Ch1

2

OUTPUT

V

CLAMP

=4V

V

CLAMP

=4.5V

10V TO +10 V INPUT

R

LOAD

=100kV

V

DD

=+5V

V

SS

=–5V

Ch1

20V

Figure 6. Overvoltage Ramp

ADG466/ADG467

–5–

REV. A

1M 10M

FREQUENCY – Hz

30M

–10
–12
–14

–16
–18
–20
–22
–24
–26
–28
–30

GAIN – dB

Figure 7. Frequency Response (Magnitude) of the ADG467,
V

DD/VSS

= ±15 V and Input Signal Level of ±100 mV

100 10M1k 10k 100k 1M

FREQUENCY – Hz

105.359

82.859

60.359

37.859

15.359

–7.141
–29.641
–52.161
–76.641
–97.161

PHASE – Degrees

Figure 8. Frequency Response (Phase) of the ADG467,
V

DD/VSS

= ±15 V and Input Signal Level of ±100 mV

100k

10k

FREQUENCY – Hz

1M 10M 40M

–10
–20
–30
–40
–50
–60
–70
–80

–90
–100
–110

CROSSTALK – dB

Figure 9. Crosstalk Between Adjacent Channels of the
ADG467, V

DD/VSS

= ±15 V and Input Signal Level of ±100 mV

10k

40M100k 1M 10M

FREQUENCY – Hz

0
–10
–20
–30
–40
–50
–60
–70
–80
–90

–100

OFF ISOLATION – dB

Figure 10. Off Isolation of the ADG467, VDD/VSS = 0 V and
Input Signal Level of

±

100 mV

CH1 2.2V2.00V CH2 2.00V M 10.0ns CH1

2

1

TEK RUN: 5.00GS/s ET SAMPLE

12.2ns

11.8ns

Figure 11. Propagation Delay Through ADG467, VDD/V

SS

=

±

15 V, Channel 1 Input and Channel 2 Output

100k

40M

1M 10M

FREQUENCY – Hz

–10
–14
–18
–22
–26
–30
–36
–38
–42
–46

–50

GAIN – dB

Figure 12. Frequency Response (Magnitude) of the ADG466,
V

DD/VSS

= ±15 V and Input Signal Level of ±100 mV

ADG466/ADG467

–6–

REV. A

100 10M1k 10k 100k 1M

FREQUENCY – Hz

40M

105.3

82.8

60.3

37.8

15.3

–7.1
–29.6
–52.1
–76.6
–92.1

PHASE – Degrees

Figure 13. Frequency Response (Phase) of the ADG466, VDD/
V

SS

= ±15 V and Input Signal Level of ±100 mV

10k

40M

100k 1M 10M

FREQUENCY – Hz

0
–10
–20
–30
–40
–50
–60
–70
–80
–90

–100

CROSSTALK – dB

Figure 14. Crosstalk Between Adjacent Channels of the
ADG466, V

DD/VSS

= ±15 V and Input Signal Level of ±100 mV

10k

40M

100k 1M 10M

FREQUENCY – Hz

0
–10
–20
–30
–40
–50
–60
–70
–80
–90

–100

OFF ISOLATION – dB

Figure 15. Off Isolation of the ADG466, VDD/VSS = 0 V and
Input Signal Level of

±

100 mV

CH1 760V1.00V CH2 1.00V M 20.0ns CH1

2

1

TEK RUN: 2.5GS/s ET SAMPLE

18.0ns

22.0ns

Figure 16. Propagation Delay Through ADG466, VDD/V

SS

=

±

15 V, Channel 1 Input and Channel 2 Output

ADG466/ADG467

–7–

REV. A

CIRCUIT INFORMATION

Figure 17 below shows a simplified schematic of a channel
protector circuit. The circuit is made up of four MOS transis­tors—two NMOS and two PMOS. One of the PMOS devices
does not lie directly in the signal path but is used to connect the
source of the second PMOS device to its backgate. This has the
effect of lowering the threshold voltage and so increasing the
input signal range of the channel for normal operation. The
source and backgate of the NMOS devices are connected for the
same reason. During normal operation the channel protectors

have a resistance of 60 Ω typ. The channel protectors are very

low power devices, and even under fault conditions the supply
current is limited to sub microampere levels. All transistors are
dielectrically isolated from each other using a trench isolation
method. This makes it impossible to latch up the channel
protectors. For an explanation, see Trench Isolation section.

NMOS

PMOS

PMOS

NMOS

V

DD

V

SS

V

SS

V

DD

Figure 17. The Channel Protector Circuit

Overvoltage Protection

When a fault condition occurs on the input of a channel protec­tor, the voltage on the input has exceeded some threshold volt­age set by the supply rail voltages. The threshold voltages are
related to the supply rails as follows. For a positive overvoltage,
the threshold voltage is given by V

DD

– VT where VTN is the

threshold voltage of the NMOS transistor (1.5 V typ). In the

case of a negative overvoltage the threshold voltage is given by
V

SS

– VTP where VTP is the threshold voltage of the PMOS de­vice (2 V typ). If the input voltage exceeds these threshold volt­ages, the output of the channel protector (no load) is clamped at
these threshold voltages. However, the channel protector output
will clamp at a voltage that is inside these thresholds if the out-

put is loaded. For example with an output load of 1 kΩ, V

DD

=

15 V and a positive overvoltage. The output will clamp at V

DD

–

V

TN

– ∆V = 15 V – 1.5 V – 0.6 V = 12.9 V where

∆

V is due to I

× R voltage drop across the channels of the MOS devices (see

Figure 19). As can be seen from Figure 19, the current during
fault condition is determined by the load on the output (i.e.,
V

CLAMP/RL

). However, if the supplies are off, the fault current is

limited to the nano-ampere level.

Figures 18, 20 and 21 show the operating conditions of the
signal path transistors during various fault conditions. Figure 18
shows how the channel protectors operate when a positive over­voltage is applied to the channel protector.

NMOS

PMOS

NMOS

V

DD

(+15V) V

SS

(–15V) V

DD

(+15V)

POSITIVE

OVERVOLTAGE

(+20V)

VDD – VTN*

(+13.5V)

*V

TN

= NMOS THRESHOLD VOLTAGE (+1.5V)

NON­SATURATED

NON-

SATURATED

SATURATED

Figure 18. Positive Overvoltage on the Channel Protector

The first NMOS transistor goes into a saturated mode of opera­tion as the voltage on its Drain exceeds the Gate voltage (V

DD

) –

the threshold voltage (V

TN

). This situation is shown in Figure

19. The potential at the source of the NMOS device is equal to
V

DD

– VTN. The other MOS devices are in a nonsaturated mode of

operations.

V

S

N

+

(V

DD

=15V)

V

D

P

–

N

+

N

+

(+20V) (+13.5V)

OVERVOLTAGE

OPERATION

(SATURATED)

VT = 1.5V

(VG – VT = 13.5V)

V

G

EFFECTIVE

SPACE CHARGE

REGION

N CHANNEL

NMOS

PMOS

NONSATURATED

OPERATION

R

L

DV

I

OUT

V

CLAMP

Figure 19. Positive Overvoltages Operation of the Channel Protector

ADG466/ADG467

–8–

REV. A

When a negative overvoltage is applied to the channel protector
circuit, the PMOS transistor enters a saturated mode of opera­tion as the drain voltage exceeds V

SS

– VTP. See Figure 20 be­low. As in the case of the positive overvoltage, the other MOS
devices are nonsaturated.

NMOS

PMOS

NMOS

V

DD

(+15V) V

SS

(–15V) V

DD

(+15V)

NEGATIVE

OVERVOLTAGE

(–20V)

V

SS

– VTP*

(–13V)

*V

TP

= PMOS THRESHOLD VOLTAGE (–2V)

NEGATIVE

OVERVOLTAGE

(–20V)

NON­SATURATED

NON-

SATURATED

SATURATED

Figure 20. Negative Overvoltage on the Channel Protector

The channel protector is also functional when the supply rails
are down (e.g., power failure) or momentarily unconnected
(e.g., rack system). This is where the channel protector has an
advantage over more conventional protection methods such as
diode clamping (see Applications Information). When V

DD

and

V

SS

equal 0 V, all transistors are off and the current is limited to

subnano-ampere levels (see Figure 21).

NMOS

PMOS

NMOS

V

DD

(0V) V

SS

(0V) V

DD

(0V)

POSITIVE OR

NEGATIVE

OVERVOLTAGE

(0V)

OFF

OFFOFF

Figure 21. Channel Protector Supplies Equal to Zero Volts

TRENCH ISOLATION

The MOS devices that make up the channel protector are iso­lated from each other by an oxide layer (trench) (see Figure 22).
When the NMOS and PMOS devices are not electrically iso­lated from each other, there exists the possibility of “latch-up”
caused by parasitic junctions between CMOS transistors. Latch­up is caused when P-N junctions that are normally reverse bi­ased become forward biased, causing large currents to flow,
which can be destructive.

CMOS devices are normally isolated from each other by Junc-
tion Isolation. In Junction Isolation, the N and P wells of the
CMOS transistors form a diode that is reverse-biased under
normal operation. However, during overvoltage conditions, this
diode becomes forward biased. A Silicon-Controlled Rectifier
(SCR) type circuit is formed by the two transistors causing a
significant amplification of the current that, in turn, leads to
latch-up. With Trench Isolation, this diode is removed; the
result is a latch-up proof circuit.

V

G

V

D

P-CHANNEL

P

+

P

+

V

S

N

–

V

G

V

D

N-CHANNEL

N

+

N

+

V

S

P

–

T
R
E
N
C
H

T
R
E
N
C
H

T

R

E
N
C
H

BURIED OXIDE LAYER

SUBSTRATE (BACKGATE)

Figure 22. Trench Isolation

ADG466/ADG467

–9–

REV. A

APPLICATIONS INFORMATION
Overvoltage and Power Supply Sequencing Protection

The ADG466 and ADG467 are ideal for use in applications
where input overvoltage protection is required and correct
power supply sequencing cannot always be guaranteed. The
overvoltage protection ensures that the output voltage of the
channel protector will not exceed the threshold voltages set by
the supplies (see Circuit Information) when there is an overvolt­age on the input. When the input voltage does not exceed these
threshold voltages, the channel protector behaves like a series

resistor (60 Ω typ). The resistance of the channel protector does

vary slightly with operating conditions (see Typical Performance
Graphs).

The power sequencing protection is afforded by the fact that
when the supplies to the channel protector are not connected,
the channel protector becomes a high resistance device. Under
this condition all transistors in the channel protector are off and
the only currents that flow are leakage currents, which are at the

µA level.

V

DD

V

SS

+5V

–5V

EDGE

CONNECTOR

ADG466

ADC

CONTROL

LOGIC

ANALOG IN

–2.5V TO +2.5V

LOGIC

LOGIC

GND

Figure 23. Overvoltage and Power Supply Sequencing
Protection

Figure 23 shows a typical application that requires overvoltage
and power supply sequencing protection. The application shows
a Hot-Insertion rack system. This involves plugging a circuit
board or module into a live rack via an edge connector. In this
type of application it is not possible to guarantee correct power
supply sequencing. Correct power supply sequencing means
that the power supplies should be connected before any external
signals. Incorrect power sequencing can cause a CMOS device
to “latch up.” This is true of most CMOS devices regardless of
the functionality. RC networks are used on the supplies of the
channel protector (Figure 23) to ensure that the rest of the
circuitry is powered up before the channel protectors. In this
way, the outputs of the channel protectors are clamped well
below V

DD

and VSS until the capacitors are charged. The diodes
ensure that the supplies on the channel protector never exceed
the supply rails of the board when it is being disconnected.

Again this ensures that signals on the inputs of the CMOS de­vices never exceed the supplies.

High Voltage Surge Suppression

The ADG466 and ADG467 are not intended for use in high
voltage applications like surge suppression. The ADG466
and ADG467 have breakdown voltages of V

SS

– 20 V and

V

DD

+ 20 V on the inputs when the power supplies are con-

nected. When the power supplies are disconnected, the break-

down voltages on the input of the channel protector are ±35 V.

In applications where inputs are likely to be subject to overvolt­ages exceeding the breakdown voltages quoted for the channel
protectors, transient voltage suppressors (TVSs) should be used.
These devices are commonly used to protect vulnerable circuits
from electric overstress such as that caused by electrostatic
discharge, inductive load switching and induced lightning. How­ever, TVSs can have a substantial standby (leakage) current

(300 µA typ) at the reverse standoff voltage. The reverse standoff

voltage of a TVS is the normal peak operating voltage of the
circuit. Also TVS offer no protection against latch-up of sensitive
CMOS devices when the power supplies are off. The best solution
is to use a channel protector in conjunction with a TVS to provide
the best leakage current specification and circuit protection.

ADG466

VDD = +5V V

SS

= –5V

ADC

TVSs
BREAKDOWN
VOLTAGE = 20V

Figure 24. High Voltage Protection

Figure 24 shows an input protection scheme that uses both a
TVS and channel protector. The TVS is selected with a reverse
standoff voltage that is much greater than operating voltage of
the circuit (TVSs with higher breakdown voltages tend to have
better standby leakage current specifications) but is inside the
breakdown voltage of the channel protector. This circuit pro­tects the circuitry whether the power supplies are present
or not.

ADG466/ADG467

–10–

REV. A

8-Lead Plastic DIP (N-8)

8

14

5

0.430 (10.92)

0.348 (8.84)

0.280 (7.11)

0.240 (6.10)

PIN 1

SEATING
PLANE

0.022 (0.558)

0.014 (0.356)

0.060 (1.52)

0.015 (0.38)

0.210 (5.33)
MAX

0.130
(3.30)
MIN

0.070 (1.77)

0.045 (1.15)

0.100
(2.54)

BSC

0.160 (4.06)

0.115 (2.93)

0.325 (8.25)

0.300 (7.62)

0.015 (0.381)

0.008 (0.204)

0.195 (4.95)

0.115 (2.93)

18-Lead Small Outline IC (R-18)

SEATING
PLANE

0.0118 (0.30)

0.0040 (0.10)

0.0192 (0.49)

0.0138 (0.35)

0.1043 (2.65)

0.0926 (2.35)

0.0500
(1.27)

BSC

0.0125 (0.32)

0.0091 (0.23)

0.0500 (1.27)

0.0157 (0.40)

8°
0°

0.0291 (0.74)

0.0098 (0.25)

x 45°

18 10

91

0.4625 (11.75)

0.4469 (11.35)

0.4193 (10.65)

0.3937 (10.00)

0.2992 (7.60)

0.2914 (7.40)

PIN 1

8-Lead Small Outline IC (SO-8)

0.1968 (5.00)

0.1890 (4.80)

8

5

41

0.2440 (6.20)

0.2284 (5.80)

PIN 1

0.1574 (4.00)

0.1497 (3.80)

0.0688 (1.75)

0.0532 (1.35)

SEATING

PLANE

0.0098 (0.25)

0.0040 (0.10)

0.0192 (0.49)

0.0138 (0.35)

0.0500
(1.27)

BSC

0.0098 (0.25)

0.0075 (0.19)

0.0500 (1.27)

0.0160 (0.41)

8°
0°

0.0196 (0.50)

0.0099 (0.25)

x 45°

20-Lead Shrink Small Outline Package (RS-20)

20 11

101

0.295 (7.50)

0.271 (6.90)

0.311 (7.9)

0.301 (7.64)

0.212 (5.38)

0.205 (5.21)

PIN 1

SEATING

PLANE

0.008 (0.203)

0.002 (0.050)

0.07 (1.78)

0.066 (1.67)

0.0256
(0.65)

BSC

0.078 (1.98)

0.068 (1.73)

0.009 (0.229)

0.005 (0.127)

0.037 (0.94)

0.022 (0.559)

8°
0°

8-Lead Micro Small Outline IC (RM-8)

8

5

4

1

0.122 (3.10)

0.114 (2.90)

0.199 (5.05)

0.187 (4.75)

PIN 1

0.0256 (0.65) BSC

0.122 (3.10)

0.114 (2.90)

SEATING

PLANE

0.006 (0.15)

0.002 (0.05)

0.018 (0.46)

0.008 (0.20)

0.043 (1.09)

0.037 (0.94)

0.120 (3.05)

0.112 (2.84)

0.011 (0.28)

0.003 (0.08)

0.028 (0.71)

0.016 (0.41)

33°
27°

0.120 (3.05)

0.112 (2.84)

OUTLINE DIMENSIONS

Dimensions shown in inches and (mm).

C2207a–0–5/98

PRINTED IN U.S.A.