ANALOG DEVICES AD9352 Service Manual

现货库存、技术资料、百科信息、热点资讯，精彩尽在鼎好!

WiMAX/WiBro RF

FEATURES

RF transceiver with integrated ADCs and DACs IEEE 802.16 WiMAX/WiBro

2.3 GHz to 2.7 GHz

3.5 MHz < BW < 20 MHz Superior receiver sensitivity with NF 3.7 dB Highly linear and spectrally pure transmitter Tx EVM −38 dB SNR > 134 dB/Hz at F Tx power control Range: 0 dB to 58 dB Resolution: 0.25 dB Autonomous AGC and Tx power control Automatic frequency correction < 0.012 ppm Integrated Frac-N synthesizer 8 Hz LO step size Integrated phase noise < 0.4°rms

APPLICATIONS

WiMAX/WiBro/BWA

OFFSET

> 22 MHz

POWER

DETECT

RADIO

SWITCHING

MxFE Transceiver

FUNCTIONAL BLOCK DIAGRAM

ADC

AD9352

DAC

GPO

CTRL

LDOs

CTRL AUX ADC AUX DAC

ADC

Figure 1.

DAC

AD9352

FILT

DATA INTERFACE

FILT

CLK/LO

SYNTH

TxNRx

DATA

SYNC

SYNC_VALID

CLK_OUT

REF_XTAL

06883-001

GENERAL DESCRIPTION

The AD9352 is a fully integrated transceiver for IEEE 802.16 WiMAX and WiBro wireless network systems. The RF MxFE™ combines the RF front-end with mixed-signal baseband enabling an easy-to-use digital interface to the baseband ASIC or FPGA. The AD9352 operates in the 2.3 GHz to 2.7 GHz range covering most of the licensed and unlicensed bands. Channel bandwidths of 3.5 MHz, 4.375 MHz, 5 MHz, 7 MHz, 8.75 MHz, 10 MHz, 14 MHz, 17.5 MHz, and 20 MHz are supported.

The direct-conversion receiver has state-of-the-art noise figure and linearity and requires no external components with the exception of a balun. The complete RF subsystem integrates an autonomous AGC loop and dc offset corrections, thus eliminating the need for high speed interaction with the baseband processor. The received signal strength indicator (RSSI) has over 80 dB of dynamic range with 0.5 dB resolution and is accessible via the serial interface.

The received signal is digitized with a high dynamic range 12-bit ADC. Decimation and channel filters produce a 10-bit output signal at the appropriate sample rate determined by the bandwidth mode. The transmit path takes a 10-bit input data and interpolates before converting to the analog domain and upconverting to the carrier frequency.

The highly linear transmit path has excellent spectral purity with sideband noise less than −134 dBc/Hz at 22 MHz offset and offers EVM of −38 dB at 0 dBm output power. The transmit power is detected by an accurate power detector and autonomously controlled with a range of 58 dB and 0.25 dB steps. The output power can be calibrated at the factory by a single measurement.

The reference frequency is produced by an internal crystal oscillator with a digital programmable frequency with 0.012 ppm resolution thus reducing the total bill of materials of the device.

An internal auxiliary ADC and two auxiliary DACs are available for system monitoring and control. Three general purpose I/Os are also included and can be register programmed or automatically sequenced by a user-defined state machine. Mode control is via a 4-wire serial port and four real-time I/O control pins.

The AD9352 is powered from a single 3.3 V supply and contains on-chip LDOs for each function to eliminate external regulators. The AD9352 is packaged in a 9 mm × 9 mm, 64-lead LFCSP.

For more information on the AD9352, e-mail Analog Devices, Inc. at wimaxtransceivers@analog.com.

Rev. Sp0

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Anal og Devices for its use, nor for any infringements of patents or ot her rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.

AD9352

NOTES

Rev. Sp0 | Page 2 of 2

ANALOG DEVICES AD9352 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual