Datasheet AD7785 Datasheet (ANALOG DEIVCES)

3-Channel, Low Noise, Low Power, 20-Bit ∑-Δ

www.BDTIC.com/ADI

FEATURES

Up to 20 bits effective resolution RMS noise

40 nV @ 4.17 Hz

85 nV @ 16.7 Hz Current: 400 μA typical Power-down: 1 μA maximum Low noise programmable gain instrumentation amp Band gap reference with 4 ppm/°C drift typical Update rate: 4.17 Hz to 470 Hz 3 differential inputs Internal clock oscillator Simultaneous 50 Hz/60 Hz rejection Programmable current sources On-chip bias voltage generator Burnout currents Power supply: 2.7 V to 5.25 V –40°C to +105°C temperature range Independent interface power supply 16-lead TSSOP package Interface

3-wire serial

SPI®, QSPI™, MICROWIRE™, and DSP compatible

Schmitt trigger on SCLK

APPLICATIONS

Thermocouple measurements RTD measurements Thermistor measurements Gas analysis

FUNCTIONAL BLOCK DIAGRAM

GND

ADC with On-Chip In-Amp and Reference

AD7785

Industrial process control Instrumentation Portable instrumentation Blood analysis Smart transmitters Liquid/gas chromatography 6-digit DVM

GENERAL DESCRIPTION

The AD7785 is a low power, low noise, complete analog front end for high precision measurement applications. The AD7785 contains a low noise 20-bit ∑-Δ ADC with three differential analog inputs. The on-chip, low noise instrumentation amplifier means that signals of small amplitude can be interfaced directly to the ADC. With a gain setting of 64, the rms noise is 40 nV when the update rate equals 4.17 Hz.

The device contains a precision low noise, low drift internal b

and gap reference and can accept an external differential reference. Other on-chip features include programmable excitation current sources, burnout currents, and a bias voltage generator. The bias voltage generator sets the common-mode voltage of a channel to AV

The AD7785 can be operated with either the internal clock

r an external clock. The output data rate from the device is

o software-programmable and can be varied from 4.17 Hz to 470 Hz. The device operates with a power supply from 2.7 V to

5.25 V. It consumes a current of 400 μA typical and is housed in a 16-lead TSSOP package.

REFIN( +)/AI N3(+)

REFIN(–)/ AIN3(–)

/2.

BIAS

AIN1(+) AIN1(–) AIN2(+) AIN2(–)

IOUT1

IOUT2

Rev. 0

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Anal og Devices for its use, nor for any infringements of patents or ot her rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.

MUX

GND

BAND GAP

REFERENCE

IN-AMPBUF

INTERNAL

CLOCK

Figure 1.

GND

SERIAL

Σ-Δ

ADC

CLK

INTERFACE

CONTRO L

LOGIC

AD7785

AND

DOUT/ RD

DIN

SCLK

06721-001

AD7785

www.BDTIC.com/ADI

Features.............................................................................................. 1

Applications....................................................................................... 1

General Description ......................................................................... 1

Functional Block Diagram .............................................................. 1

Revision History ............................................................................... 2

Specifications..................................................................................... 3

Timing Characteristics..................................................................... 6

Timing Diagrams.......................................................................... 7

Absolute Maximum Ratings............................................................ 8

ESD Caution.................................................................................. 8

Pin Configuration and Function Descriptions............................. 9

Output Noise and Resolution Specifications ..............................11

External Reference...................................................................... 11

Internal Reference ...................................................................... 12

Typical Performance Characteristics ........................................... 13

On-Chip Registers.......................................................................... 14

Communications Register......................................................... 14

Status Register............................................................................. 15

Mode Register ............................................................................. 15

Configuration Register ..............................................................17

Data Register............................................................................... 18

ID Register................................................................................... 18

IO Register................................................................................... 18

Offset Register ............................................................................ 19

Full-Scale Register...................................................................... 19

ADC Circuit Information.............................................................. 20

Overview ..................................................................................... 20

Digital Interface.......................................................................... 21

Circuit Description......................................................................... 25

Analog Input Channel............................................................... 25

Instrumentation Amplifier........................................................ 25

Bipolar/Unipolar Configuration .............................................. 25

Data Output Coding .................................................................. 25

Burnout Currents....................................................................... 26

Excitation Currents.................................................................... 26

Bias Voltage Generator .............................................................. 26

Reference ..................................................................................... 26

Reset ............................................................................................. 26

Monitor ............................................................................. 27

Calibration................................................................................... 27

Grounding and Layout.............................................................. 27

Applications Information.............................................................. 29

Temperature Measurement using a Thermocouple............... 29

Temperature Measurement using an RTD.............................. 30

Outline Dimensions....................................................................... 31

Ordering Guide .......................................................................... 31

REVISION HISTORY

4/07—Revision 0: Initial Version

Rev. 0 | Page 2 of 32

AD7785

www.BDTIC.com/ADI

SPECIFICATIONS

AVDD = 2.7 V to 5.25 V; DVDD = 2.7 V to 5.25 V; GND = 0 V; all specifications T

Table 1.

Parameter AD7785B1 Unit Test Conditions/Comments

ADC CHANNEL

Output Update Rate 4.17 to 470 Hz nom No Missing Codes

20 Bits min Resolution See Output Noise and Resolution Specifications Output Noise and Update Rates See Output Noise and Resolution Specifications Integral Nonlinearity ±15 ppm of FSR max Offset Error Offset Error Drift vs. Temperature Full-Scale Error Gain Drift vs. Temperature

3, 5

±1 μV typ

±10 nV/°C typ

±10 μV typ

±1 ppm/°C typ Gain = 1 to 16, external reference ±3 ppm/°C typ Gain = 32 to 128, external reference Power Supply Rejection 100 dB min AIN = 1 V/gain, gain ≥ 4, external reference

ANALOG INPUTS

Differential Input Voltage Ranges ±V

Absolute AIN Voltage Limits

/Gain V nom

REF

Unbuffered Mode GND – 30 mV V min Gain = 1 or 2

AVDD + 30 mV V max

Buffered Mode GND + 100 mV V min Gain = 1 or 2

AVDD – 100 mV V max

In-Amp Active GND + 300 mV V min Gain = 4 to 128

AVDD – 1.1 V max

Common-Mode Voltage, VCM 0.5 V min

Analog Input Current

Buffered Mode or In-Amp Active

Average Input Current

±1 nA max Gain = 1 or 2, update rate < 100 Hz ±250 pA max Gain = 4 to 128, update rate < 100 Hz

Average Input Current Drift ±2 pA/°C typ

Unbuffered Mode Gain = 1 or 2

Average Input Current ±400 nA/V typ Input current varies with input voltage Average Input Current Drift ±50 pA/V/°C typ

Normal Mode Rejection

Internal Clock

@ 50 Hz, 60 Hz 65 dB min 80 dB typ, 50 ± 1 Hz, 60 ± 1 Hz, FS[3:0] = 1010 @ 50 Hz 80 dB min 90 dB typ, 50 ± 1 Hz, FS[3:0] = 1001 @ 60 Hz 90 dB min 100 dB typ, 60 ± 1 Hz, FS[3:0] = 1000

External Clock

@ 50 Hz, 60 Hz 80 dB min 90 dB typ, 50 ± 1 Hz, 60 ± 1 Hz, FS[3:0] = 1010 @ 50 Hz 94 dB min 100 dB typ, 50 ± 1 Hz, FS[3:0] = 1001 @ 60 Hz 90 dB min 100 dB typ, 60 ± 1 Hz, FS[3:0] = 1000

Common-Mode Rejection

@ DC 100 dB min AIN = 1 V/gain, gain ≥ 4 @ 50 Hz, 60 Hz @ 50 Hz, 60 Hz

100 dB min 50 ± 1 Hz, 60 ± 1 Hz, FS[3:0] = 1010

100 dB min

MIN

to T

, unless otherwise noted.

MAX

= REFIN(+) − REFIN(−) or internal reference,

REF

gain = 1 to 128

VCM = (AIN(+) + AIN(−))/2, gain = 4 to 128

50 ± 1 Hz (FS[3:0] = 1001) (FS[3:0] = 1000)

, 60 ± 1 Hz

Rev. 0 | Page 3 of 32

AD7785

www.BDTIC.com/ADI

Parameter AD7785B1 Unit Test Conditions/Comments

REFERENCE

Internal Reference

Internal Reference Initial Accuracy 1.17 ± 0.01% V min/max AVDD = 4 V, TA = 25°C

Internal Reference Drift

15 ppm/°C max

Power Supply Rejection 85 dB typ

External Reference

External REFIN Voltage 2.5 V nom

Reference Voltage Range

AVDD V max

Absolute REFIN Voltage Limits

Average Reference Input Current 400 nA/V typ

Average Reference Input Current

Drift

Normal Mode Rejection Same as for analog inputs Common-Mode Rejection 100 dB typ

EXCITATION CURRENT SOURCES

(IEXC1 and IEXC2) Output Current 10/210/1000 μA nom Initial Tolerance at 25°C ±5 % typ Drift 200 ppm/°C typ Current Matching ±0.5 % typ Matching between IEXC1 and IEXC2; V Drift Matching 50 ppm/°C typ Line Regulation (VDD) 2 %/V typ AVDD = 5 V ± 5% Load Regulation 0.2 %/V typ Output Compliance

TEMPERATURE SENSOR

Accuracy Sensitivity

BIAS VOLTAGE GENERATOR

AVDD/2 V nom

BIAS

Generator Start-Up Time See Figure 10 ms/nF typ Dependent on the capacitance on the AIN pin

BIAS

INTERNAL/EXTERNAL CLOCK

Internal Clock

Frequenc y

Duty Cycle 50:50 % typ

External Clock

Frequency 64 kHz nom

Duty Cycle 45:55 to 55:45 % typ

LOGIC INPUTS

, Input Low Voltage 0.8 V max DVDD = 5 V

INL

, Input High Voltage

INH

4 ppm/°C typ

REFIN = REFIN(+) − REFIN(−)

0.1 V min

GND − 30 mV

+ 30 mV V max

±0.03 nA/V/°C t

AVDD − 0.65

AVDD − 1.1

GND − 30 mV

±2

0.81

V min

V max 10 μA or 210 μA currents selected

V max 1 mA currents selected

V min

°C typ mV/°C typ

When V limited to 0.9 × V

= AVDD, the differential input must be

REF

/gain if the in-amp is active

REF

Applies if user calibrates the temperature sensor Applies if user calibrates the temperature sensor

64 ± 3% kHz min/max

A 128 kHz external clock can be used if the

-by-2 function is used

divide (Bit CLK1 = CLK0 = 1)

Applies for external 64 kHz clock; a 128 kHz

an have a less stringent duty cycle

clock c

0.4

2.0

V max V min

= 3 V

= 3 V or 5 V

OUT

= 0 V

Rev. 0 | Page 4 of 32

AD7785

www.BDTIC.com/ADI

Parameter AD7785B1 Unit Test Conditions/Comments

SCLK, CLK, and DIN (Schmitt-

Triggered Input)

VT(+) 1.4/2 V min/V max DVDD = 5 V VT(–) 0.8/1.7 V min/V max DVDD = 5 V VT(+) − VT(−) VT(+) 0.9/2 V min/V max DVDD = 3 V VT(–) 0.4/1.35 V min/V max DVDD = 3 V VT(+) − VT(−)

Input Currents Input Capacitance

LOGIC OUTPUTS (INCLUDING CLK)

VOH, Output High Voltage

VOL, Output Low Voltage VOH, Output High Voltage VOL, Output Low Voltage

Floating-State Leakage Current ±10 μA max Floating-State Output Capacitance 10 pF typ Data Output Coding Offset binary

SYSTEM CALIBRATION

Full-Scale Calibration Limit +1.05 × FS V max Zero-Scale Calibration Limit

Input Span 0.8 × FS V min

2.1 × FS V max

POWER REQUIREMENTS

Power Supply Voltage

AVDD to GND

DVDD to GND

Power Supply Currents

IDD Current 140 μA max

185 μA max

400 μA max

500 μA max

IDD (Power-Down Mode) 1 μA max

Temperature range is –40°C to +105°C.

Specification is not production tested, but is supported by characterization data at initial product release.

Following a calibration, this error is in the order of the noise for the programmed gain and update rate selected.

Recalibration at any temperature removes these errors.

Full-scale error applies to both positive and negative full-scale and applies at the factory calibration conditions (AVDD = 4 V, gain = 1, TA = 25°C).

FS[3:0] are the four bits used in the mode register to select the output word rate.

Digital inputs equal to DVDD or GND with excitation currents and bias voltage generator disabled.

0.1/0.17 V min/V max DVDD = 5 V

0.06/0.13 V min/V max DVDD = 3 V

±10

DVDD − 0.6

0.4 V max DVDD = 3 V, I

4 V min DVDD = 5 V, I

0.4 V max

μA max pF typ

VIN = DVDD or GND All digital inputs

V min DVDD = 3 V, I

= 5 V, I

= 100 μA

SOURCE

= 100 μA

SINK

= 200 μA

SOURCE

= 1.6 mA (DOUT/RDY)/

SINK

800 μA (CLK)

−1.05 × FS

V min

2.7/5.25 V min/max

110 μA typ @ AV

= 3 V, 125 μA typ @ AVDD = 5 V,

unbuffered mode, external reference 130 μA typ @ AV

= 3 V, 165 μA typ @ AVDD = 5 V,

buffered mode, gain = 1 or 2, external reference 300 μA typ @ AV

= 3 V, 350 μA typ @ AVDD = 5 V,

gain = 4 to 128, external reference 400 μA typ @ AV

= 3 V, 450 μA typ @ AVDD = 5 V,

gain = 4 to 128, internal reference

Rev. 0 | Page 5 of 32

AD7785

www.BDTIC.com/ADI

TIMING CHARACTERISTICS

AVDD = 2.7 V to 5.25 V, DVDD = 2.7 V to 5.25 V, GND = 0 V, Input Logic 0 = 0 V, Input Logic 1 = DVDD, unless otherwise noted.

Table 2.

Parameter

1, 2

Limit at T

MIN

, T

(B Version) Unit Conditions/Comments

MAX

t3 100 ns min SCLK high pulse width t4 100 ns min SCLK low pulse width Read Operation

t1 0 ns min

falling edge to DOUT/RDY active time

CS 60 ns max DVDD = 4.75 V to 5.25 V 80 ns max DVDD = 2.7 V to 3.6 V

0 ns min SCLK active edge to data valid delay

60 ns max DVDD = 4.75 V to 5.25 V 80 ns max DVDD = 2.7 V to 3.6 V

5, 6

10 ns min

Bus relinquish time after CS

inactive edge 80 ns max t6 0 ns min t7 10 ns min

SCLK inactive edge to CS SCLK inactive edge to DOUT/RDY

inactive edge

high

Write Operation

t8 0 ns min

falling edge to SCLK active edge setup time

t9 30 ns min Data valid to SCLK edge setup time t10 25 ns min Data valid to SCLK edge hold time t11 0 ns min

Sample tested during initial release to ensure compliance. All input signals are specified with tR = tF = 5 ns (10% to 90% of DVDD) and timed from a voltage level of 1.6 V.

See Figure 3 and Figure 4.

These numbers are measured with the load circuit shown in Figure 2 and defined as the time required for the output to cross the VOL or VOH limits.

SCLK active edge is the falling edge of SCLK.

These numbers are derived from the measured time taken by the data output to change 0.5 V when loaded with the circuit shown in Figure 2. The measured number

is then extrapolated back to remove the effects of charging or discharging the 50 pF capacitor. This means that the times quoted in the timing characteristics are the true bus relinquish times of the part and, as such, are independent of external bus loading capacitances.

RDY

returns high after a read of the ADC. In single conversion mode and continuous conversion mode, the same data can be read again, if required, while although care should be taken to ensure that subsequent reads do not occur close to the next output update. In continuous read mode, the digital word can be read only once.

rising edge to SCLK edge hold time

RDY

is high,

(1.6mA WITH DVDD = 5V,

SINK

100µA WIT H DV

= 3V)

OUTPUT

50pF

SOURCE

100µA WIT H DV

Figure 2. Load Circuit for Timing Characterization

1.6V

(200µA WIT H DVDD = 5V,

= 3V)

6721-002

Rev. 0 | Page 6 of 32

AD7785

www.BDTIC.com/ADI

TIMING DIAGRAMS

CS (I)

DOUT/RDY (O)

SCLK (I)

NOTES

1. I = INPUT, O = OUTPUT

MSB LSB

Figure 3. Read Cycle Timing Diagram

CS (I)

06721-003

06721-004

CLK (I)

DIN (I)

NOTES

1. I = INPUT, O = OUTPUT

MSB LSB

Figure 4. Write Cycle Timing Diagram

Rev. 0 | Page 7 of 32

AD7785

www.BDTIC.com/ADI

ABSOLUTE MAXIMUM RATINGS

TA = 25°C, unless otherwise noted.

Table 3.

Parameter Rating

AVDD to GND

DVDD to GND

Analog Input Voltage to GND

Reference Input Voltage to GND

Digital Input Voltage to GND

Digital Output Voltage to GND

AIN/Digital Input Current 10 mA Operating Temperature Range

Storage Temperature Range

Maximum Junction Temperature 150°C TSSOP

θJA Thermal Impedance 150.4°C/W θJC Thermal Impedance 27.6°C/W

Lead Temperature, Soldering

Reflow 260°C

−0.3 V to +7 V

−0.3 V to AVDD + 0.3 V

−0.3 V to DVDD + 0.3 V

−40°C to +105°C

−65°C to +150°C

Stresses above those listed under Absolute Maximum Ratings

y cause permanent damage to the device. This is a stress

ma rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

ESD CAUTION

Rev. 0 | Page 8 of 32

AD7785

www.BDTIC.com/ADI

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

SCLK

CLK

IOUT1

IN1(+)

IN1(–)

IN2(+)

IN2(–) REFIN(+)/AIN3(+)

(Not to Scale)

Figure 5. Pin Configuration

Table 4. Pin Function Descriptions

Pin No. Mnemonic Description

1 SCLK

Serial Clock Input. This serial clock input is f triggered input, making the interface suitable for opto-isolated applications. The serial clock can be continuous with all data transmitted in a continuous train of pulses. Alternatively, it can be a noncontinuous clock with the information being transmitted to or from the ADC in smaller batches of data.

2 CLK

Clock In/Clock Out. The internal clock can be made available at this pin. Alternatively, the internal clock can be disabled

, and the ADC can be driven by an external clock. This allows several ADCs to be driven from a

common clock, allowing simultaneous conversions to be performed.

Chip Select Input. This is an active low logic input used to select the ADC. CS can be used to select the ADC in systems with more than one device on the serial bus or as a frame synchronization signal in communicating with the device. CS can be hardwired low, allowing the ADC to operate in 3-wire mode with SCLK, DIN, and DOUT used to interface with the device.

4 IOUT1

Output of Internal Excitation Current Source. The internal ex this pin. The excitation current source is programmable so that the current can be 10 μA, 210 μA, or 1 mA. Either IEXC1 or IEXC2 can be switched to this output.

5 AIN1(+)

AIN1(−) Analog Input. AIN1(−) is the negative terminal of the differential analog input pair AIN1(+)/AIN1(−). 7 AIN2(+)

AIN2(−) Analog Input. AIN2(−) is the negative terminal of the differential analog input pair AIN2(+)/AIN2(−). 9 REFIN(+)/AIN3(+)

Analog Input. AIN1(+) is the positive terminal of the differential analog input pair AIN1(+)/AIN1(−).

Analog Input. AIN2(+) is the positive terminal of the differential analog input pair AIN2(+)/AIN2(−).

Positive Reference Input/Analog Input. An external r REFIN(−). REFIN(+) can lie anywhere between AV

REFIN(+) − REFIN(−) is 2.5 V, but the part functions with a reference from 0.1 V to AV pin can function as AIN3(+) where AIN3(+) is the positive terminal of the differential analog input pair AIN3(+)/AIN3(−).

REFIN(−)/AIN3(−)

Negative Reference Input/Analog Input. REFIN(−) input can lie anywhere between GND and AV negative terminal of the differential analog input pair AIN3(+)/AIN3(−).

11 IOUT2

Output of Internal Excitation Current Source. The internal ex this pin. The excitation current source is programmable so that the current can be 10 μA, 210 μA, or 1 mA.

Either IEXC1 or IEXC2 can be switched to this output. 12 GND Ground Reference Point. 13 AVDD Supply Voltage, 2.7 V to 5.25 V. 14 DVDD

Digital Interface Supply Voltage. The logic levels for the serial interface pins are related to this supply, which

ween 2.7 V and 5.25 V. The DV

is bet

equal 5 V with DV

at 3 V or vice versa.

DIN

DOUT/RDY

AD7785

TOP VIEW

GND

IOUT2

REFIN(–)/ AIN3(–)

06721-005

or data transfers to and from the ADC. The SCLK has a Schmitt-

citation current source can be made available at

eference can be applied between REFIN(+) and

and GND + 0.1 V. The nominal reference voltage

. Alternatively, this

is the negative reference input for REFIN. This reference

− 0.1 V. This pin also functions as AIN3(−), which is the

citation current source can be made available at

voltage is independent of the voltage on AVDD; therefore, AVDD can

Rev. 0 | Page 9 of 32

AD7785

www.BDTIC.com/ADI

Pin No. Mnemonic Description

16 DIN

DOUT/RDY

Serial Data Output/Data Ready Output. DOUT/RDY serves a dual purpose. It functions as a serial data output pin to access the output shift register of the ADC. The output shift register can contain data from any of the on-chip data or control registers. In addition, DOUT/RDY the completion of a conversion. If the data is not read after the conversion, the pin goes high before the

next update occurs. The DOUT/RDY With an external serial clock, the data can be read using the DOUT/RDY pin. With CS low, the data/control word information is placed on the DOUT/RDY rising edge.

Serial Data Input. This serial da transferred to the control registers within the ADC; the register selection bits of the communications register identify the appropriate register.

operates as a data ready pin, going low to indicate

falling edge can be used as an interrupt to a processor, indicating that valid data is available.

pin on the SCLK falling edge and is valid on the SCLK

ta input is to the input shift register on the ADC. Data in this shift register is

Rev. 0 | Page 10 of 32

AD7785

www.BDTIC.com/ADI

OUTPUT NOISE AND RESOLUTION SPECIFICATIONS

EXTERNAL REFERENCE

Tabl e 5 shows the output rms noise of the AD7785 for some of the update rates and gain settings. The numbers given are for the bipolar input range with an external 2.5 V reference. These numbers are typical and are generated with a differential input voltage of 0 V. o

utput peak-to-peak (p-p) resolution shown in parentheses. It is

Table 6 shows the effective resolution, with the

important to note that the effective resolution is calculated using the rms noise, while the p-p resolution is based on the p-p noise. The p-p resolution represents the resolution for which there is no code flicker. These numbers are typical and are rounded to the nearest LSB.

Table 5. Output RMS Noise (μV) vs.

Update Rate (Hz) Gain of 1 Gain of 2 Gain of 4 Gain of 8 Gain of 16 Gain of 32 Gain of 64 Gain of 128

4.17 0.64 0.6 0.29 0.22 0.1 0.065 0.039 0.041

8.33 1.04 0.96 0.38 0.26 0.13 0.078 0.057 0.055

16.7 1.55 1.45 0.54 0.36 0.18 0.11 0.087 0.086

33.2 2.3 2.13 0.74 0.5 0.23 0.17 0.124 0.118 62 2.95 2.85 0.92 0.58 0.29 0.2 0.153 0.144 123 4.89 4.74 1.49 1 0.48 0.32 0.265 0.283 242 11.76 9.5 4.02 1.96 0.88 0.45 0.379 0.397 470 11.33 9.44 3.07 1.79 0.99 0.63 0.568 0.593

Table 6. Typical Resolution (Bits) vs. Gain and Output

Update Rate (Hz) Gain of 1 Gain of 2 Gain of 4 Gain of 8 Gain of 16 Gain of 32 Gain of 64 Gain of 128

4.17 20 (20) 20 (19.5) 20 (19.5) 20 (19) 20 (19) 20 (18.5) 20 (18.5) 20 (17.5)

8.33 20 (19.5) 20 (19) 20 (19) 20 (18.5) 20 (18.5) 20 (18.5) 20 (18) 19.5 (17)

16.7 20 (19) 20 (18) 20 (18.5) 20 (18) 20 (18) 20 (18) 20 (17.5) 19 (16.5)

33.2 20 (18.5) 20 (17.5) 20 (18) 20 (17.5) 20 (18) 20 (17.5) 19 (16.5) 18.5 (16) 62 20 (18) 19.5 (17) 20 (18) 20 (17.5) 20 (17.5) 19.5 (17) 19 (16.5) 18 (15.5) 123 20 (17.5) 19 (16.5) 19.5 (17) 19 (16.5) 19.5 (17) 19 (16.5) 18 (15.5) 17 (14.5) 242 18.5 (16) 18 (15.5) 18 (15.5) 18 (15.5) 18.5 (16) 18.5 (16) 17.5 (15) 16.5 (14) 470 18.5 (16) 18 (15.5) 18.5 (16) 18.5 (16) 18 (15.5) 18 (15.5) 17 (14.5) 16 (13.5)

Gain and Output Update Rate Using an External 2.5 V Reference

Update Rate Using an External 2.5 V Reference

Rev. 0 | Page 11 of 32

AD7785

www.BDTIC.com/ADI

INTERNAL REFERENCE

Tabl e 7 shows the output rms noise of the AD7785 for some of the update rates and gain settings. The numbers given are for the bipolar input range with the internal 1.17 V reference. These numbers are typical and are generated with a differential input voltage of 0 V. o

utput peak-to-peak (p-p) resolution given in parentheses. It is

Table 8 shows the effective resolution, with the

important to note that the effective resolution is calculated using the rms noise, while the p-p resolution is calculated based on p-p noise. The p-p resolution represents the resolution for which there is no code flicker. These numbers are typical and are rounded to the nearest LSB.

Table 7. Output RMS Noise (μV) vs. Gain and Outp

Update Rate (Hz) Gain of 1 Gain of 2 Gain of 4 Gain of 8 Gain of 16 Gain of 32 Gain of 64 Gain of 128

4.17 0.81 0.67 0.32 0.2 0.13 0.065 0.04 0.039

8.33 1.18 1.11 0.41 0.25 0.16 0.078 0.058 0.059

16.7 1.96 1.72 0.55 0.36 0.25 0.11 0.088 0.088

33.2 2.99 2.48 0.83 0.48 0.33 0.17 0.13 0.12 62 3.6 3.25 1.03 0.65 0.46 0.2 0.15 0.15 123 5.83 5.01 1.69 0.96 0.67 0.32 0.25 0.26 242 11.22 8.64 2.69 1.9 1.04 0.45 0.35 0.34 470 12.46 10.58 4.58 2 1.27 0.63 0.50 0.49

Table 8. Typical Resolution (Bits) vs. Gain and Outp

Update Rate (Hz) Gain of 1 Gain of 2 Gain of 4 Gain of 8 Gain of 16 Gain of 32 Gain of 64 Gain of 128

4.17 20 (19) 20.5 (18) 20 (18.5) 20.5 (18) 20 (17.5) 20 (17.5) 20 (17.5) 19 (16.5)

8.33 20 (18.5) 20 (17.5) 20.5 (18) 20 (17.5) 20 (17.5) 20 (17.5) 19 (16.5) 18 (15.5)

16.7 20 (17.5) 19.5 (17) 20 (17.5) 19.5 (17) 19 (16.5) 19.5 (17) 18.5 (16) 17.5 (15)

33.2 19.5 (17) 19 (16.5) 19.5 (17) 19 (16.5) 19 (16.5) 18.5 (16) 18 (15.5) 17 (14.5) 62 19.5 (17) 18.5 (16) 19 (16.5) 19 (16.5) 18.5 (16) 18.5 (16) 18 (15.5) 17 (14.5) 123 18.5 (16) 18 (15.5) 18.5 (16) 18 (15.5) 17.5 (15) 18 (15.5) 17 (14.5) 16 (13.5) 242 17.5 (15) 17 (14.5) 17.5 (15) 17 (14.5) 17 (14.5) 17.5 (15) 16.5 (14) 15.5 (13) 470 17.5 (15) 17 (14.5) 17 (14.5) 17 (14.5) 17 (14.5) 17 (14.5) 16 (13.5) 15 (12.5)

ut Update Rate Using the Internal Reference

Rev. 0 | Page 12 of 32

AD7785

www.BDTIC.com/ADI

TYPICAL PERFORMANCE CHARACTERISTICS

8388800

8388750

8388700

8388650

8388600

CODE READ

8388550

8388500

8388450

0 1000800600400200

READING NUMBER

Figure 6. Typical Noise Plot (Internal Reference, Gain = 64,

date Rate = 16.7 Hz)

OCCURRENCE

8388482 8388750838872083886808388640838860083885608388520

CODE

OCCURRENCE (%)

06721-006

–1.75 –1.05 –0.70 –0.35 0 0.35 0.70 1.05 1.40 1.75

MATCHING (%)

06721-009

Figure 9. Excitation Current Matching (1 mA) at Ambient Temperature

POWER-UP TIME (ms)

06721-007

0 200 400 600 800 1000

LOAD CAPACITANCE (nF)

06721-010

Figure 7. Noise Distribution Histogram

Figure 10. Bias Voltage Generator Power-Up Time vs. Load Capacitance

(Internal Reference, Gain = 64, Update Rate = 16.7 Hz)

3.0 VDD = 5V

UPDATE RATE = 16.6Hz T

= 25°C

OCCURRENCE (%)

–2.0 –1.2 –0.8 –0.4 0 0.4 0.8 1.2 1.6 2.0

MATCHING (%)

06721-008

Figure 8. Excitation Current Matching (210 μA) at Ambient

emperature

2.5

2.0

1.5

RMS NOISE (µ V)

1.0

0.5

0 0.5 1.0 1.5 2.0 2. 5 3. 0 3.5 4.0 4.5 5.0

Figure 11. RMS Noise vs. Reference Voltage (Gain = 1)

Rev. 0 | Page 13 of 32

REFERENCE VOLTAGE (V)

06721-011

AD7785

www.BDTIC.com/ADI

ON-CHIP REGISTERS

The ADC is controlled and configured via a number of on-chip registers, which are described on the following pages. In the following descriptions, set implies a Logic 1 state and cleared implies a Logic 0 state, unless otherwise stated.

COMMUNICATIONS REGISTER

RS2, RS1, RS0 = 0, 0, 0

The communications register is an 8-bit write-only register. All communications to the part must start with a write operation to the communications register. The data written to the communications register determines whether the next operation is a read or write operation, and to which register this operation takes place. For read or write operations, once the subsequent read or

CR7 CR6 CR5 CR4 CR3 CR2 CR1 CR0

WEN(0) R/W(0)

Table 9. Communications Register Bit Designations

Bit Location Bit Name Description

CR7

CR6

CR5 to CR3 RS2 to RS0

CR2 CREAD

CR1 to CR0 0 These bits must be programmed to Logic 0 for correct operation.

WEN

R/W

Write Enable Bit. A 0 must be written to this bit so that the write to the communications register actually occurs. If a 1 is the first bit written, the part does not clock on to subsequent bits in the register. It stays at this bit location until a 0 is written to this bit. Once a 0 is written to the the communications register.

A 0 in this bit location indicates that the next operation is a write to a specified register. A 1 in this position indicates that the next operation is a read from the designated register.

Continuous Read of the Data Register. When this bit is set t interface is configured so that the data register can be continuously read. For example, the contents of the data register are placed on the DOUT pin automatically when the SCLK pulses are applied after the RDY

goes low to indicate that a conversion is complete. The communications register does not have to be written to for data reads. To enable continuous read mode, the instruction 01011100 must be written to the communications register. To exit the continuous read mode, the instruction 01011000 must be written to the communications register while the RDY pin is low. While in continuous read mode, the ADC monitors activity on the DIN line so that it can receive the instruction to exit continuous read mode. Additionally, a reset occurs if 32 consecutive 1s are seen on DIN. Therefore, DIN should be held low in continuous read mode until an instruction is to be written to the device.

RS2(0) RS1(0) RS0(0) CREAD(0) 0(0) 0(0)

ing this serial interface communication. See Table 10.

write operation to the selected register is complete, the interface returns to where it expects a write operation to the communications register. This is the default state of the interface and, on power-up or after a reset, the ADC is in this default state waiting for a write operation to the communications register. In situations where the interface sequence is lost, a write operation of at least 32 serial clock cycles with DIN high returns the ADC to this default state by resetting the entire part.

he bit designations for the communications register. CR0

t through CR7 indicate the bit location, CR denoting the bits are in the communications register. CR7 denotes the first bit of the data stream. The number in parentheses indicates the poweron/reset default status of that bit.

bit, the next seven bits are loaded to

WEN

o 1 (and the data register is selected), the serial

Tabl e 9 outlines

Table 10. Register Selection

RS2 RS1 RS0 Register Register Size

0 0 0 Communications Register During a Write Operation 8-bit 0 0 0 Status Register During a Read Operation 8-bit 0 0 1 Mode Register 16-bit 0 1 0 Configuration Register 16-bit 0 1 1 Data Register 24-bit (20-bit conversion followed by four 1s) 1 0 0 ID Register 8-bit 1 0 1 IO Register 8-bit 1 1 0 Offset Register 24-bit 1 1 1 Full-Scale Register 24-bit

Rev. 0 | Page 14 of 32

AD7785

www.BDTIC.com/ADI

STATUS REGISTER

RS2, RS1, RS0 = 0, 0, 0; Power-On/Reset = 0x88

The status register is an 8-bit read-only register. To access the ADC status register, the user must write to the communications register, select the next operation to be a read, and load Bit RS2, Bit RS1, and Bit RS0 with 0. Ta b le 1 1 outlines the bit designations for the status

egister. SR0 through SR7 indicate the bit locations, and SR denotes that the bits are in the status register. SR7 denotes the first bit of the

r data stream. The number in parentheses indicates the power-on/reset default status of that bit.

SR7 SR6 SR5 SR4 SR3 SR2 SR1 SR0

RDY(1)

Table 11. Status Register Bit Designations

Bit Location Bit Name Description

SR7

SR6 ERR

SR5 to SR4 0 These bits are automatically cleared. SR3 1 This bit is automatically set on the AD7785. SR2 to SR0 CH2 to CH0 These bits indicate which channel is being converted by the ADC.

ERR(0) 0(0) 0(0) 1 (1) CH2(0) CH1(0) CH0(0)

RDY

Ready Bit for ADC. Cleared when data is written to the ADC data register. The RDY bit is set automatically after the ADC data register has been read or a period before the data register is updated with a new conversion result to indicate to the user not to read the conversion data. It is also set when the part is placed in power-down mode. The end of a conversion is indicated by the DOUT/ be used as an alternative to the status register for monitoring the ADC for conversion data.

ADC Error Bit. This bit is written to at the same time as the RDY the ADC data register has been clamped to all 0s or all 1s. Error sources include overrange and underrange. Cleared by a write operation to start a conversion.

bit. Set to indicate that the result written to

pin also. This pin can

RDY

MODE REGISTER

RS2, RS1, RS0 = 0, 0, 1; Power-On/Reset = 0x000A

The mode register is a 16-bit register from which data can be read or to which data can be written. This register is used to select the operating mode, update rate, and clock source. Tabl e 12 outlines the bit designations for the mode register. MR0 through MR15 indicate

he bit locations, MR denoting the bits are in the mode register. MR15 denotes the first bit of the data stream. The number in parentheses

t indicates the power-on/reset default status of that bit. Any write to the setup register resets the modulator and filter and sets the

MR15 MR14 MR13 MR12 MR11 MR10 MR9 MR8

MD2(0) MD1(0) MD0(0) 0(0) 0(0) 0(0) 0(0) 0(0)

MR7 MR6 MR5 MR4 MR3 MR2 MR1 MR0

CLK1(0) CLK0(0) 0(0) 0(0) FS3(1) FS2(0) FS1(1) FS0(0)

Table 12. Mode Register Bit Designations

Bit Location Bit Name Description MR15 to MR13 MD2 to MD0 Mode Select Bits. These bits select the operational mode of the AD7785 (see Tabl e 13). MR12 to MR8 0 These bits must be programmed with a Logic 0 for correct operation. MR7 to MR6 CLK1 to CLK0

0 0 Internal 64 kHz Clock. Internal clock is not available at the CLK pin. 0 1 Internal 64 kHz Clock. This clock is made available at the CLK pin. 1 0

1 1 External Clock Used. The external clock is divided by 2 within the AD7785. MR5 to MR4 0 These bits must be programmed with a Logic 0 for correct operation. MR3 to MR0 FS3 to FS0 Filter Update Rate Select Bits (see Table 14).

These bits are used to select the clock source for the AD7785. Ei clock can be used. The ability to override using an external clock allows several AD7785 devices to be synchronized. In addition, 50 Hz/60 Hz is improved when an accurate external clock drives the AD7785.

CLK1 CLK0 ADC Clock Source

External 64 kHz Clock Used. An external clock gives better 50 Hz/60 Hz rejection. See

ations for external clock.

specific

ther an on-chip 64 kHz clock or an external

RDY

bit.

Rev. 0 | Page 15 of 32

AD7785

www.BDTIC.com/ADI

Table 13. Operating Modes

MD2 MD1 MD0 Mode

0 0 0

0 0 1

0 1 0

0 1 1

1 0 0

1 0 1

1 1 0

1 1 1

Continuous Conversion Mode (Default).

n continuous conversion mode, the ADC continuously performs conversions and places the result in the data

I register. RDY continuous read mode, whereby the conversions are automatically placed on the DOUT line when SCLK pulses are applied. Alternatively, the user can instruct the ADC to output the conversion by writing to the communications register. After power-on, a channel change, or a write to the mode, configuration, or IO registers, the first conversion is available after a period of 2/f

Single Conversion Mode. When sing requires 1 ms to power up and settle. The ADC then performs the conversion, which takes a time of 2/f conversion result is placed in the data register, RDY

conversion remains in the data register, and RDY performed.

Idle Mode.

n idle mode, the ADC filter and modulator are held in a reset state, although the modulator clocks are still provided.

I Power-Down Mode.

n power-down mode, all the AD7785 circuitry is powered down, including the current sources, burnout currents,

I bias voltage generator, and CLKOUT circuitry.

Internal Zero-Scale Calibration. An in complete. RDY ADC is placed in idle mode following a calibration. The measured offset coefficient is placed in the offset register of the selected channel.

Internal Full-Scale Calibration. A full-scale in When the gain equals 1, a calibration takes 2 conversion cycles to complete. For higher gains, 4 conversion cycles are required to perform the full-scale calibration.

goes high when the calibration is initiated and returns low when the calibration is complete. The ADC is placed

RDY in idle mode following a calibration. The measured full-scale coefficient is placed in the full-scale register of the selected channel. Internal full-scale calibrations cannot be performed when the gain equals 128. With this gain setting, a system fullscale calibration can be performed. A full-scale calibration is required each time the gain of a channel is changed to minimize the full-scale error.

System Zero-Scale Calibration. The user should system offset calibration takes 2 conversion cycles to complete. returns low when the calibration is complete. The ADC is placed in idle mode following a calibration. The measured offset coefficient is placed in the offset register of the selected channel.

System Full-Scale Calibration. The user should A calibration takes 2 conversion cycles to complete. when the calibration is complete. The ADC is placed in idle mode following a calibration. The measured full-scale coefficient is placed in the full-scale register of the selected channel. A full-scale calibration is required each time the gain of a channel is changed.

goes low when a conversion is complete. The user can read these conversions by placing the device in

. Subsequent conversions are available at a frequency of f

ADC

le conversion mode is selected, the ADC powers up and performs a single conversion. The oscillator

goes low, and the ADC returns to power-down mode. The

remains active low until the data is read or another conversion is

ternal short is automatically connected to the enabled channel. A calibration takes 2 conversion cycles to

goes high when the calibration is initiated and returns low when the calibration is complete. The

put voltage is automatically connected to the selected analog input for this calibration.

connect the system zero-scale input to the channel input pins as selected by the CH2 to CH0 bits. A

goes high when the calibration is initiated and

RDY

connect the system full-scale input to the channel input pins as selected by the CH2 to CH0 bits.

goes high when the calibration is initiated and returns low

RDY

ADC

. The

ADC

Table 14. Update Rates Available

FS3 FS2 FS1 FS0 f

0 0 0 0 x x 0 0 0 1 470 4 0 0 1 0 242 8 0 0 1 1 123 16 0 1 0 0 62 32 0 1 0 1 50 40 0 1 1 0 39 48 0 1 1 1 33.2 60 1 0 0 0 19.6 101 90 dB (60 Hz only)

(Hz) t

ADC

(ms) Rejection @ 50 Hz/60 Hz (Internal Clock)

SETTLE

Rev. 0 | Page 16 of 32

AD7785

www.BDTIC.com/ADI

FS3 FS2 FS1 FS0 f

1 0 0 1 16.7 120 80 dB (50 Hz only) 1 0 1 0 16.7 120 65 dB (50 Hz and 60 Hz) 1 0 1 1 12.5 160 66 dB (50 Hz and 60 Hz) 1 1 0 0 10 200 69 dB (50 Hz and 60 Hz) 1 1 0 1 8.33 240 70 dB (50 Hz and 60 Hz) 1 1 1 0 6.25 320 72 dB (50 Hz and 60 Hz) 1 1 1 1 4.17 480 74 dB (50 Hz and 60 Hz)

CONFIGURATION REGISTER

RS2, RS1, RS0 = 0, 1, 0; Power-On/Reset = 0x0710

The configuration register is a 16-bit register from which data can be read or to which data can be written. This register is used to configure the ADC for unipolar or bipolar mode, enable or disable the buffer, enable or disable the burnout currents, select the gain, and select the analog input channel.

cations; CON denotes that the bits are in the configuration register. CON15 denotes the first bit of the data stream. The number in

lo parentheses indicates the power-on/reset default status of that bit.

CON15 CON14 CON13 CON12 CON11 CON10 CON9 CON8

VBIAS1(0) VBIAS0(0) BO(0)

CON7 CON6 CON5 CON4 CON3 CON2 CON1 CON0

REFSEL(0) 0(0) 0(0) BUF(1) 0(0) CH2(0) CH1(0) CH0(0)

Tabl e 1 5 outlines the bit designations for the filter register. CON0 through CON15 indicate the bit

(Hz) t

ADC

(ms) Rejection @ 50 Hz/60 Hz (Internal Clock)

SETTLE

U/B

(0)

BOOST(0) G2(1) G1(1) G0(1)

Table 15. Configuration Register Bit Designations

Bit Location Bit Name Description CON15 to

CON14

0 0 Bias voltage generator disabled 0 1

1 0

1 1 Reserved CON13 BO

CON12

CON11 BOOST

CON10 to CON8

0 0 0 1 (In-amp not used) 2.5 V 0 0 1 2 (In-amp not used) 1.25 V 0 1 0 4 625 mV 0 1 1 8 312.5 mV 1 0 0 16 156.2 mV 1 0 1 32 78.125 mV 1 1 0 64 39.06 mV 1 1 1 128 19.53 mV

VBIAS1 to VBIAS0

U/B

G2 to G0 Gain Select Bits.

Bias Voltage Generator Enable. The negative terminal of the analog inputs can be biased up to AVDD/2. These bits are used in conjunction with the boost bit.

VBIAS1 VBIAS0 Bias Voltage

Burnout Current Enable Bit. When this bit is set to 1 by the user, the 100 nA current sources in the signal path

e enabled. When BO = 0, the burnout currents are disabled. The burnout currents can be enabled only

ar when the buffer or in-amp is active. The burnout currents are available on Channels AIN1 and AIN2.

Unipolar/Bipolar Bit. Set by user to enable unipolar coding. Therefore, a zero differential input results in 0x00000 output, and a full-scale differential input results in 0xFFFFF output. Cleared by the user to enable bipolar coding. Negative full-scale differential input results in an output code of 0x00000, zero differential input results in an output code of 0x80000, and a positive full-scale differential input results in an output code of 0xFFFFF.

This bit is used in conjunction with the voltage generator is increased. This reduces its power-up time.

Written by the user to select the ADC input range as follows:

G2 G1 G0 Gain ADC Input Range (2.5 V Reference)

Bias voltage connected to AIN1(−)

Bias voltage connected to AIN2(−)

VBIAS1 and VBIAS0 bits. When set, the current consumed by the bias

Rev. 0 | Page 17 of 32

AD7785

www.BDTIC.com/ADI

Bit Location Bit Name Description CON7 REFSEL Reference Select Bit. The reference source for the ADC is selected using this bit.

0 External Reference Applied between REFIN(+) and REFIN(–). 1 Internal Reference Selected. CON6 to

CON5 CON4 BUF

CON3 0 This bit must be programmed with a Logic 0 for correct operation. CON2 to

CON0

0 0 0 AIN1(+) – AIN1(–) 0 0 0 1 AIN2(+) – AIN2(–) 1 0 1 0 AIN3(+) – AIN3(–) 2 0 1 1 AIN1(−) – AIN1(−) 0 1 0 0 Reserved 1 0 1 Reserved 1 1 0 Temp Sensor Automatically selects gain = 1 and internal reference 1 1 1 AVDD Monitor

0 These bits must be programmed with a Logic 0 for correct operation.

CH2 to CH0

DATA REGISTER

RS2, RS1, RS0 = 0, 1, 1; Power-On/Reset = 0x00000F

The conversion result from the ADC is stored in this data register. This is a read-only register. On completion of a read operation from this register, the

RDY

bit/pin is set. This is a 24-bit register. The 20-bit conversion is contained in the 20 MSBs. The 4 LSBs are set to 1.

REFSEL Reference Source

Configures the ADC for buffered or unbuffered mode of operation. If cleared, the ADC oper mode, lowering the power consumption of the device. If set, the ADC operates in buffered mode, allowing the user to place source impedances on the front end without contributing gain errors to the system. The buffer can be disabled when the gain equals 1 or 2. For higher gains, the buffer is automatically enabled.

With the buffer disabled, the voltage on the analog input pins can be from 30 mV below GND to 30 mV above

. When the buffer is enabled, it requires some headroom, so the voltage on any input pin must be limited

to 100 mV within the power supply rails.

Channel Select Bits. Written by the user to selec

CH2 CH1 CH0 Channel Calibration Pair

t the active analog input channel to the ADC.

Automatically selects gain = 1/6 and 1.17 V

ference

ates in unbuffered

ID REGISTER

RS2, RS1, RS0 = 1, 0, 0; Power-On/Reset = 0xXB

The identification number for the AD7785 is stored in the ID register. This is a read-only register.

IO REGISTER

RS2, RS1, RS0 = 1, 0, 1; Power-On/Reset = 0x00

The IO register is an 8-bit register from which data can be read or to which data can be written. This register is used to enable and select the value of the excitation currents. Tab le 1 6 outlines the bit designations for the IO register. IO0 through IO7 indicate the bit locations;

O denotes that the bits are in the IO register. IO7 denotes the first bit of the data stream. The number in parentheses indicates the power-

I on/reset default status of that bit.

IO7 IO6 IO5 IO4 IO3 IO2 IO1 IO0

0(0) 0(0) 0(0) 0(0) IEXCDIR1(0) IEXCDIR0(0) IEXCEN1(0) IEXCEN0(0)

Rev. 0 | Page 18 of 32

AD7785

www.BDTIC.com/ADI

Table 16. IO Register Bit Designations

Bit Location Bit Name Description IO7 to IO4 0 These bits must be programmed with a Logic 0 for correct operation. IO3 to IO2

0 0

0 1

1 0

1 1

IO1 to IO0

0 0 Excitation Current Disabled 0 1 10 μA 1 0 210 μA 1 1 1 mA

IEXCDIR1 to

CDIR0

IEX

IEXCEN1 to

CEN0

IEX

OFFSET REGISTER

RS2, RS1, RS0 = 1, 1, 0; Power-On/Reset = 0x800000

Each analog input channel has a dedicated offset register that holds the offset calibration coefficient for the channel. This register is 24 bits wide and its power-on/reset value is 0x8000(00). The offset register is used in conjunction with its associated full-scale register to form a register pair. The poweron reset value is automatically overwritten if an internal or system zero-scale calibration is initiated by the user. The offset register is a read/write register. However, the AD7785 must be in idle mode or power-down mode when writing to the offset register.

Direction of current sources select bits.

IEXCDIR1 IEXCDIR0 Current Source Direction

Current Source IEXC1 connected to Pin IOUT1, Current Source IEXC2

onnected to Pin IOUT2.

c Current Source IEXC1 connected to Pin IOUT2, Current Source IEXC2

onnected to Pin IOUT1.

c Both current sources connected to Pin IOUT1. Permitted when the current

ces are set to 10 μA or 210 μA only.

sour Both current sources connected to Pin IOUT2. Permitted when the current

ces are set to 10 μA or 210 μA only.

sour

These bits are used to enable and disable the current sources along with selecting the value of the excitation currents.

IEXCEN1 IEXCEN0 Current Source Value

FULL-SCALE REGISTER

RS2, RS1, RS0 = 1, 1, 1; Power-On/Reset = 0x5XXX00

The full-scale register is a 24-bit register that holds the full-scale calibration coefficient for the ADC. The AD7785 has 3 full-scale registers, each channel having a dedicated full-scale register. The full-scale registers are read/write registers; however, when writing to the full-scale registers, the ADC must be placed in power-down mode or idle mode. These registers are configured on power-on with factory-calibrated full-scale calibration coefficients, the calibration being performed at gain = 1. Therefore, every device has different default coefficients. The coefficients are different depending on whether the internal reference or an external reference is selected. The default value is automatically overwritten if an internal or system full-scale calibration is initiated by the user, or the full-scale register is written to.

Rev. 0 | Page 19 of 32

AD7785

www.BDTIC.com/ADI

ADC CIRCUIT INFORMATION

OVERVIEW

The AD7785 is a low power ADC that incorporates a ∑-Δ modulator, a buffer, reference, in-amp, and an on-chip digital filter intended for the measurement of wide dynamic range, low frequency signals such as those in pressure transducers, weigh scales, and temperature measurement applications.

The part has three differential inputs that can be buffered or

buffered. The device can be operated with the internal 1.17 V

un reference, or an external reference can be used. Figure 12 shows t

he basic connections required to operate the part.

The output rate of the AD7785 (f allowable update rates, along with their corresponding settling times, are listed in

ction of the digital filter. Simultaneous 50 Hz and 60 Hz

fun

Tabl e 1 4 . Normal mode rejection is the major

rejection is optimized when the update rate equals 16.7 Hz or less as notches are placed at both 50 Hz and 60 Hz with these update rates (see

Figure 14.)

HERMOCOUPL E

JUNCTION

) is user-programmable. The

ADC

AIN1(+) AIN1(–)

AIN2(+)

AIN2(–)

REFIN(+)

REF

REFIN(–)

IOUT2

BIAS

GND

MUX

GND

The AD7785 uses slightly different filter types, depending on

e output update rate so that the rejection of quantization

th noise and device noise is optimized. When the update rate is from 4.17 Hz to 12.5 Hz, a Sinc3 filter, along with an averaging filter, is used. When the update rate is from 16.7 Hz to 39 Hz, a modified Sinc3 filter is used. This filter provides simultaneous 50 Hz/60 Hz rejection when the update rate equals 16.7 Hz. A Sinc4 filter is used when the update rate is from 50 Hz to 242 Hz. Finally, an integrate-only filter is used when the update rate equals 470 Hz.

Figure 13 to Figure 16 show the frequency response of the dif

ferent filter types for several update rates.

REFIN(+) REFIN(–)

BAND GAP

REFERENCE

IN-AMPBUF

INTERNAL

CLOCK

Σ-Δ

ADC

GND

SERIAL

INTERFACE

AND

CONTROL

LOGIC

AD7785

DOUT/RD

DIN

SCLK

CLK

06721-012

Figure 12. Basic Connection Diagram

–20

–40

(dB)

–60

–80

–100

0 12010080604020

FREQUENCY ( Hz)

Figure 13. Filter Profile with Update Rate = 4.17 Hz

Rev. 0 | Page 20 of 32

06721-013

AD7785

www.BDTIC.com/ADI

–20

–40

(dB)

–60

–80

–100

0 20018016014012010080604020

FREQUENCY ( Hz)

Figure 14. Filter Profile with Update Rate = 16.7 Hz

–20

–40

(dB)

–60

–80

–100

0 30002500200015001000500

FREQUENCY ( Hz)

Figure 15. Filter Profile with Update Rate = 242 Hz

–10

DIGITAL INTERFACE

The programmable functions of the AD7785 are controlled using a set of on-chip registers. Data is written to these registers via the serial interface of the device; read access to the on-chip registers is also provided by this interface. All communications with the device must start with a write to the communications register. After power-on or reset, the device expects a write to its communications register. The data written to this register determines whether the next operation is a read operation or a write operation and determines to which register this read or write operation occurs. Therefore, write access to any of the

06721-014

06721-015

other registers on the part begins with a write operation to the communications register followed by a write to the selected register. A read operation from any other register (except when continuous read mode is selected) starts with a write to the communications register followed by a read operation from the selected register.

The serial interface of the AD7785 consists of four signals: DIN, SCLK, and DOUT/ data into the on-chip registers, and DOUT/

RDY

. The DIN line is used to transfer

RDY

is used for

accessing from the on-chip registers. SCLK is the serial clock input for the device, and all data transfers (either on DIN or

RDY

DOUT/ DOUT/

) occur with respect to the SCLK signal. The

RDY

pin operates as a data-ready signal also; the line

going low when a new data-word is available in the output register. It is reset high when a read operation from the data register is complete. It also goes high prior to the updating of the data register to indicate when not to read from the device to ensure that a data read is not attempted while the register is being updated.

is used to select a device. It can be used to decode the AD7785 in systems where several components are connected to the serial bus.

–20

–30

(dB)

–40

–50

–60

0 10000900080007000600050004000300020001000

FREQUENCY ( Hz)

Figure 16. Filter Response at 470 Hz Update Rate

06721-016

Rev. 0 | Page 21 of 32

AD7785

www.BDTIC.com/ADI

Figure 3 and Figure 4 show timing diagrams for interfacing to the AD7785 with shows the timing for a read operation from the AD7785 output shift register, and

ion to the input shift register. It is possible to read the same

t word from the data register several times, even though the DOUT/ However, care must be taken to ensure that the read operations have been completed before the next output update occurs. In continuous read mode, the data register can be read only once.

The serial interface can operate in 3-wire mode by tying In this case, the SCLK, DIN, and DOUT/ to communicate with the AD7785. The end of the conversion can be monitored using the scheme is suitable for interfacing to microcontrollers. If required as a decoding signal, it can be generated from a port

pin. For microcontroller interfaces, it is recommended that SCLK idle high between data transfers.

The AD7785 can be operated with synchronization signal. This scheme is useful for DSP interfaces. In this case, the first bit (MSB) is effectively clocked out by because in DSPs. The SCLK can continue to run between data transfers, provided the timing numbers are obeyed.

The serial interface can be reset by writing a series of 1s on the D 32 serial clock cycles, the serial interface is reset. This ensures that the interface can be reset to a known state if the interface gets lost due to a software error or some glitch in the system. Reset returns the interface to the state in which it is expecting a write to the communications register. This operation resets the contents of all registers to their power-on values. Following a reset, the user should allow a period of 500 μs before addressing the serial interface.

The AD7785 can be configured to continuously convert or to p

RDY

IN input. If a Logic 1 is written to the AD7785 line for at least

erform a single conversion. See Figure 17 through Figure 19.

being used to decode the part. Figure 3

Figure 4 shows the timing for a write opera-

line returns high after the first read operation.

low.

RDY

lines are used

RDY

bit in the status register. This

being used as a frame

would normally occur after the falling edge of SCLK

Single Conversion Mode

In single conversion mode, the AD7785 is placed in shutdown mode between conversions. When a single conversion is initiated by setting MD2, MD1, MD0 to 0, 0, 1 in the mode register, the AD7785 powers up, performs a single conversion, and then returns to power-down mode. The on-chip oscillator requires 1 ms to power up. A conversion requires a time period of 2 × t

. DOUT/

ADC

conversion. When the data-word has been read from the data register, DOUT/ remains high until another conversion is initiated and completed. The data register can be read several times, if required, even when DOUT/

RDY

goes low to indicate the completion of a

RDY

goes high. If CS is low, DOUT/

RDY

has gone high.

RDY

Continuous Conversion Mode

This is the default power-up mode. The AD7785 continuously

RDY

converts, the a conversion is completed. If also goes low when a conversion is complete. To read a conver-

sion, the user writes to the communications register indicating that the next operation is a read of the data register. The digital conversion is placed on the DOUT/

pulses are applied to the ADC. DOUT/ the conversion is read. The user can read this register additional times, if required. However, the user must ensure that the data register is not being accessed at the completion of the next conversion, otherwise the new conversion word is lost.

pin in the status register going low each time

is low, the DOUT/

RDY

pin as soon as SCLK

RDY

line

returns high when

Rev. 0 | Page 22 of 32

AD7785

www.BDTIC.com/ADI

DIN

DOUT/RDY

SCLK

DIN

DOUT/RDY

0x08 0x200A

0x58

DATA

Figure 17. Single Conversion

0x58 0x58

DATA DATA

06721-017

SCLK

Figure 18. Continuous Conversion

6721-018

Rev. 0 | Page 23 of 32

AD7785

www.BDTIC.com/ADI

Continuous Read

Rather than write to the communications register to access the data each time a conversion is complete, the AD7785 can be configured so that the conversions are placed on the

RDY

DOUT/ communications register, the user needs only to apply the 24 SCLK cycles to the ADC, and the 20-bit result followed by four 1s is automatically placed on the DOUT/ conversion is complete. The ADC should be configured for continuous conversion mode.

When DOUT/ sion, sufficient SCLK cycles must be applied to the ADC, and the data conversion is placed on the DOUT/ the conversion is read, DOUT/ conversion is available. In this mode, the data can be read only once. In addition, the user must ensure that the data-word is

line automatically. By writing 01011100 to the

RDY

goes low to indicate the end of a conver-

RDY

returns high until the next

line when a

RDY

line. When

read before the next conversion is complete. If the user has not read the conversion before the completion of the next conversion, or if insufficient serial clocks are applied to the AD7785 to read the word, the serial output register is reset when the next conversion is completed, and the new conversion is placed in the output serial register.

To exit the continuous read mode, the instruction 01011000

ust be written to the communications register while the

m DOUT/ the ADC monitors activity on the DIN line so that it can receive the instruction to exit the continuous read mode. Additionally, a reset occurs if 32 consecutive 1s are seen on DIN. Therefore, DIN should be held low in continuous read mode until an instruction is written to the device.

RDY

pin is low. While in the continuous read mode,

DIN

DOUT/RDY

SCLK

0x5C

DA TA D ATA D ATA

Figure 19. Continuous Read

06721-019

Rev. 0 | Page 24 of 32

AD7785

www.BDTIC.com/ADI

CIRCUIT DESCRIPTION

ANALOG INPUT CHANNEL

The AD7785 has three differential analog input channels. These are connected to the on-chip buffer amplifier when the device is operated in buffered mode and directly to the modulator when the device is operated in unbuffered mode. In buffered mode (the BUF bit in the mode register is set to 1), the input channel feeds into a high impedance input stage of the buffer amplifier. Therefore, the input can tolerate significant source impedances and is tailored for direct connection to external resistive-type sensors, such as strain gauges or resistance temperature detectors (RTDs).

When BUF = 0, the part is operated in unbuffered mode.

his results in a higher analog input current. Note that this

T unbuffered input path provides a dynamic load to the driving source. Therefore, resistor/capacitor combinations on the input pins can cause gain errors, depending on the output impedance of the source that is driving the ADC input. allowable external resistance/capacitance values for unbuffered mode such that no gain error at the 20-bit level is introduced.

Table 17. External R-C Combination for 20-Bit No Gain Error

C (pF) R (Ω)

50 9 k 100 6 k 500 1.5 k 1000 900 5000 200

The AD7785 can be operated in unbuffered mode only when the gain equals 1 or 2. At higher gains, the buffer is automatically enabled. The absolute input voltage range in buffered mode is restricted to a range between GND + 100 mV and AV

– 100 mV. When the gain is set to 4 or higher, the in-amp

is enabled. The absolute input voltage range when the in-amp is active is restricted to a range between GND + 300 mV and AV

− 1.1 V. Take care in setting up the common-mode voltage

so that these limits are not exceeded to avoid degradation in linearity and noise performance.

The absolute input voltage in unbuffered mode includes the

ange between GND – 30 mV and AV

r being unbuffered. The negative absolute input voltage limit does allow the possibility of monitoring small true bipolar signals with respect to GND.

Table 1 7 shows the

+ 30 mV as a result of

INSTRUMENTATION AMPLIFIER

Amplifying the analog input signal by a gain of 1 or 2 is performed digitally within the AD7785. However, when the gain equals 4 or higher, the output from the buffer is applied to the input of the on-chip instrumentation amplifier. This low noise in-amp means that signals of small amplitude can be gained within the AD7785 while still maintaining excellent noise performance.

For example, when the gain is set to 64, the rms noise is 40 nV ty

pically, which is equivalent to 20 bits effective resolution or

18.5 bits peak-to-peak resolution.

The AD7785 can be programmed to have a gain of 1, 2, 4, 8, 16, 32, 64, a register. Therefore, with an external 2.5 V reference, the unipolar ranges are from 0 mV to 20 mV to 0 V to 2.5 V while the bipolar ranges are from ±20 mV to ±2.5 V. When the in-amp is active (gain ≥ 4), the common-mode voltage (AIN(+) + AIN(–))/2 must be greater than or equal to 0.5 V.

If the AD7785 is operated with an external reference that has a val 90% of V operation.

nd 128 using Bit G2 to Bit G0 in the configuration

ue equal to AV

/gain when the in-amp is active, for correct

REF

, the analog input signal must be limited to

BIPOLAR/UNIPOLAR CONFIGURATION

The analog input to the AD7785 can accept either unipolar or bipolar input voltage ranges. A bipolar input range does not imply that the part can tolerate negative voltages with respect to system GND. Unipolar and bipolar signals on the AIN(+) input are referenced to the voltage on the AIN(–) input. For example, if AIN(−) is 2.5 V, and the ADC is configured for unipolar mode and a gain of 1, the input voltage range on the AIN(+) pin is

2.5 V to 5 V.

If the ADC is configured for bipolar mode, the analog input

nge on the AIN(+) input is 0 V to 5 V. The bipolar/unipolar

ra option is chosen by programming the U/ tion register.

bit in the configura-

DATA OUTPUT CODING

When the ADC is configured for unipolar operation, the output code is natural (straight) binary with a zero differential input voltage resulting in a code of 00000 hex, a midscale voltage resulting in a code of 80000, and a full-scale input voltage resulting in a code of FFFFF. The output code for any analog input voltage can be represented as

Code = (2

When the ADC is configured for bipolar operation, the output

de is offset binary with a negative full-scale voltage resulting

co in a code of 00000 hex, a zero differential input voltage resulting in a code of 80000 hex, and a positive full-scale input voltage resulting in a code of FFFFF hex. The output code for any analog input voltage can be represented as

Code = 2

where:

AIN is t GAIN is the in-amp setting (1 to 128). N = 20.

× AIN × GAIN)/V

N – 1

× [(AIN × GAIN /V

he analog input voltage.

REF

) + 1]

Rev. 0 | Page 25 of 32

AD7785

www.BDTIC.com/ADI

BURNOUT CURRENTS

Burnout currents are available on Channels AIN1 and AIN2. The burnout currents are 100 nA constant current generators, one sourcing current from AV current from AIN(–) to GND. The currents are switched to the selected analog input pair. Both currents are either on or off, depending on the burnout current enable (BO) bit in the configuration register. These currents can be used to verify that an external transducer is still operational before attempting to take measurements on that channel. Once the burnout currents are turned on, they flow in the external transducer circuit, and a measurement of the input voltage on the analog input channel can be taken. If the resultant voltage measured is full scale, the user needs to verify why this is the case. A full-scale reading could mean that the front-end sensor is open circuit. It could also mean that the front-end sensor is overloaded and is justified in outputting full scale, or the reference may be absent, thus clamping the data to all 1s.

When reading all 1s from the output, the user needs to check

hese three cases before making a judgment. If the voltage

t measured is 0 V, it may indicate that the transducer has short circuited. For normal operation, these burnout currents are turned off by writing a 0 to the BO bit in the configuration register. The current sources work over the normal absolute input voltage range specifications with buffers on.

EXCITATION CURRENTS

The AD7785 also contains two matched, software-configurable, constant current sources that can be programmed to equal 10 μA, 210 μA, or 1 mA. Both source currents from the AV are directed to either the IOUT1 or IOUT2 pin of the device. These current sources are controlled via bits in the IO register. The configuration bits enable the current sources, direct the current sources to IOUT1 or IOUT2, and select the value of the current. These current sources can be used to excite external resistive bridge or RTD sensors.

BIAS VOLTAGE GENERATOR

A bias voltage generator is included on the AD7785. This biases the negative terminal of the selected input channel to AV It is useful in thermocouple applications, because the voltage generated by the thermocouple must be biased about some dc voltage if the gain is greater than 2. This is necessary because the instrumentation amplifier requires headroom to ensure that signals close to GND or AV

The bias voltage generator is controlled using the VBIAS1 and

AS0 bits in conjunction with the boost bit in the configura-

VBI tion register. The power-up time of the bias voltage generator is dependent on the load capacitance. To accommodate higher load capacitances, the AD7785 has a boost bit. When this bit is set to 1, the current consumed by the bias voltage generator increases, so that the power-up time is considerably reduced. Figure 10 shows the power-up time when boost equals 0 and 1 fo

r different load capacitances.

to AIN(+) and one sinking

are converted accurately.

/2.

The current consumption of the AD7785 increases by 40 μA

hen the bias voltage generator is enabled, and boost equals 0.

w With the boost function enabled, the current consumption increases by 250 μA.

REFERENCE

The AD7785 has an embedded 1.17 V reference that can be used to supply the ADC, or an external reference can be applied. The embedded reference is a low noise, low drift reference, the drift being 4 ppm/°C typically. For external references, the ADC has a fully differential input capability for the channel. The reference source for the AD7785 is selected using the REFSEL bit in the configuration register. When the internal reference is selected, it is internally connected to the modulator. It is not available on the REFIN pins.

The common-mode range for these differential inputs is from

o AV

GND t excessive R-C source impedances introduce gain errors. The reference voltage REFIN (REFIN(+) − REFIN(−)) is 2.5 V nominal, but the AD7785 is functional with reference voltages from 0.1 V to AV

In applications where the excitation (voltage or current) for the t

ransducer on the analog input also drives the reference voltage for the part, the effect of the low frequency noise in the excitation source is removed because the application is ratiometric. If the AD7785 is used in a nonratiometric application, a low noise reference should be used.

Recommended 2.5 V reference voltage sources for the AD7785

clude the ADR381 and ADR391, which are low noise, low

in power references. Also, note that the reference inputs provide a high impedance, dynamic load. Because the input impedance of each reference input is dynamic, resistor/capacitor combinations on these inputs can cause dc gain errors, depending on the output impedance of the source that is driving the reference inputs.

Reference voltage sources like those recommended previously (s

uch as the ADR391) typically have low output impedances and are, therefore, tolerant to having decoupling capacitors on REFIN(+) without introducing gain errors in the system. Deriving the reference input voltage across an external resistor means that the reference input sees a significant external source impedance. External decoupling on the REFIN pins is not recommended in this type of circuit configuration.

. The reference input is unbuffered; therefore,

RESET

The circuitry and serial interface of the AD7785 can be reset by writing 32 consecutive 1s to the device. This resets the logic, the digital filter, and the analog modulator while all on-chip registers are reset to their default values. A reset is automatically performed on power-up. When a reset is initiated, the user must allow a period of 500 μs before accessing any of the onchip registers. A reset is useful if the serial interface becomes asynchronous due to noise on the SCLK line.

Rev. 0 | Page 26 of 32

AD7785

www.BDTIC.com/ADI

AVDD MONITOR

Along with converting external voltages, the ADC can be used to monitor the voltage on the AV Bit CH0 equal 1, the voltage on the AV attenuated by 6, and the resultant voltage is applied to the ∑-Δ modulator using an internal 1.17 V reference for analog-todigital conversion. This is useful, because variations in the power supply voltage can be monitored.

pin. When Bit CH2 to

pin is internally

CALIBRATION

The AD7785 provides four calibration modes that can be programmed via the mode bits in the mode register. These are internal zero-scale calibration, internal full-scale calibration, system zero-scale calibration, and system full-scale calibration, which effectively reduces the offset error and full-scale error to the order of the noise. After each conversion, the ADC conversion result is scaled using the ADC calibration registers before being written to the data register. The offset calibration coefficient is subtracted from the result prior to multiplication by the full-scale coefficient.

To start a calibration, write the relevant value to the MD2 to

its in the mode register. After the calibration is complete,

MD0 b the contents of the corresponding calibration registers are updated, the pin goes low (if

During an internal zero-scale or full-scale calibration, the

espective zero input and full-scale input are automatically

r connected internally to the ADC input pins. A system calibration, however, expects the system zero-scale and system full-scale voltages to be applied to the ADC pins before the calibration mode is initiated. In this way, external ADC errors are removed.

From an operational point of view, a calibration should be t

reated like another ADC conversion. A zero-scale calibration (if required) should always be performed before a full-scale calibration. System software should monitor the the status register or the DOUT/ end of calibration via a polling sequence or an interrupt-driven routine.

Both an internal offset calibration and a system offset cal

ibration take two conversion cycles. An internal offset calibration is not needed, as the ADC itself removes the offset continuously.

To perform an internal full-scale calibration, a full-scale input volt

age is automatically connected to the selected analog input for this calibration. When the gain equals 1, a calibration takes 2 conversion cycles to complete. For higher gains, 4 conversion cycles are required to perform the full-scale calibration. DOUT/ returns low when the calibration is complete.

RDY

bit in the status register is set, the DOUT/

is low), and the AD7785 reverts to idle mode.

RDY

pin to determine the

RDY

goes high when the calibration is initiated and

RDY

bit in

The ADC is placed in idle mode following a calibration. The m

easured full-scale coefficient is placed in the full-scale register of the selected channel. Internal full-scale calibrations cannot be performed when the gain equals 128. With this gain setting, a system full-scale calibration can be performed. A full-scale calibration is required each time the gain of a channel is changed to minimize the full-scale error.

An internal full-scale calibration can be performed at specified

pdate rates only. For gains of 1, 2, and 4, an internal full-scale

u calibration can be performed at any update rate. However, for higher gains, internal full-scale calibrations can be performed when the update rate is less than or equal to 16.7 Hz, 33.2 Hz, and 50 Hz only. However, the full-scale error does not vary with the update rate, so a calibration at one update rate is valid for all update rates (assuming the gain or reference source is not changed).

A system full-scale calibration takes 2 conversion cycles to

mplete, irrespective of the gain setting. A system full-scale

co calibration can be performed at all gains and all update rates. If system offset calibrations are being performed along with system full-scale calibrations, the offset calibration should be performed before the system full-scale calibration is initiated.

GROUNDING AND LAYOUT

Because the analog inputs and reference inputs of the ADC are differential, most of the voltages in the analog modulator are common-mode voltages. The excellent common-mode rejection of the part removes common-mode noise on these inputs. The digital filter provides rejection of broadband noise on the power supply, except at integer multiples of the modulator sampling frequency. The digital filter also removes noise from the analog and reference inputs, provided that these noise sources do not saturate the analog modulator. As a result, the AD7785 is more immune to noise interference than a conventional high resolution converter. However, because the resolution of the AD7785 is so high, and the noise levels from the AD7785 is so low, care must be taken with regard to grounding and layout.

The printed circuit board that houses the AD7785 should be desig

ned such that the analog and digital sections are separated and confined to certain areas of the board. A minimum etch technique is generally best for ground planes because it provides the best shielding.

It is recommended that the GND pins of the AD7785 be tied

o the AGND plane of the system. In any layout, it is important

t to keep in mind the flow of currents in the system, ensuring that the return paths for all currents are as close as possible to the paths the currents took to reach their destinations. Avoid forcing digital currents to flow through the AGND sections of the layout.

Rev. 0 | Page 27 of 32

AD7785

www.BDTIC.com/ADI

The ground planes of the AD7785 should be allowed to run under the device to prevent noise coupling. The power supply lines to the AD7785 should use as wide a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. Fast switching signals such as clocks should be shielded with digital ground to avoid radiating noise to other sections of the board, and clock signals should never be run near the analog inputs.

Avoid crossover of digital and analog signals. Traces on opposi

te sides of the board should run at right angles to each other. This reduces the effects of feedthrough through the board. A microstrip technique is by far the best, but it is not always possible with a double-sided board. In this technique, the component side of the board is dedicated to ground planes, and signals are placed on the solder side.

Good decoupling is important when using high resolution

Cs. AV

AD parallel with 0.1 μF capacitors to GND. DV decoupled with 10 μF tantalum in parallel with 0.1 μF capacitors to the system’s DGND plane, with the system’s AGND to DGND connection being close to the AD7785.

To achieve the best from these decoupling components, they sh

ould be placed as close as possible to the device, ideally right

up against the device. All logic chips should be decoupled with

0.1 μF ceramic capacitors to DGND.

should be decoupled with 10 μF tantalum in

should be

Rev. 0 | Page 28 of 32

AD7785

www.BDTIC.com/ADI

APPLICATIONS INFORMATION

The AD7785 provides a low cost, high resolution analog-todigital function. Because the analog-to-digital function is provided by a ∑-Δ architecture, the part is more immune to noisy environments, making it ideal for use in sensor measurement and industrial and process control applications.

TEMPERATURE MEASUREMENT USING A THERMOCOUPLE

Figure 20 outlines a connection from a thermocouple to the AD7785. In a thermocouple application, the voltage generated by the thermocouple is measured with respect to an absolute reference, so the internal reference is used for this conversion. The cold junction measurement uses a ratiometric configuration, so the reference is provided externally.

Because the signal from the thermocouple is small, the AD7785 is o

perated with the in-amp enabled to amplify the signal from

the thermocouple. As the input channel is buffered, large

HERMOCOUPLE

JUNCTION

GND

BIAS

AIN1(+) AIN1(–)

AIN2(+)

AIN2(–)

REFIN(+)

REF

REFIN(–)

IOUT2

MUX

GND

decoupling capacitors can be placed on the front end to eliminate any noise pickup that may be present in the thermocouple leads. The AD7785 has a reduced commonmode range with the in-amp enabled, so the bias voltage generator provides a common-mode voltage so that the voltage generated by the thermocouple is biased up to AV

/2.

The cold junction compensation is performed using a thermis-

or. The on-chip excitation current supplies the thermistor. In

t addition, the reference voltage for the cold junction measurement is derived from a precision resistor in series with the thermistor. This allows a ratiometric measure-ment so that variation of the excitation current has no effect on the measurement (it is the ratio of the precision reference resistance to the thermistor resistance that is measured).

REFIN(+) REF IN(–)

BAND GAP

REFERENCE

IN-AMPBUF

INTERNAL

CLOCK

Σ-Δ

ADC

GND

SERIAL

INTERFACE

AND

CONTROL

LOGIC

AD7785

DOUT/RD

DIN

SCLK

CLK

Figure 20. Thermocouple Measurement Using the AD7785

06721-020

Rev. 0 | Page 29 of 32

AD7785

www.BDTIC.com/ADI

TEMPERATURE MEASUREMENT USING AN RTD

To optimize a 3-wire RTD configuration, two identically matched current sources are required. The AD7785, which contains two well-matched current sources, is ideally suited to these applications. One possible 3-wire configuration is shown in

Figure 21. In this 3-wire configuration, the lead resistances

esult in errors if only one current is used, as the excitation

r current flows through RL1, developing a voltage error between AIN1(+) and AIN1(–). In the scheme outlined, the second RTD current source is used to compensate for the error introduced by the excitation current flowing through RL1. The second RTD current flows through RL2. Assuming RL1 and RL2 are equal (the leads would normally be of the same material and of equal

RL1

RTD

RL2

RL3

GND

IOUT1

AIN1(+)

AIN1(–)

IOUT2

REFIN(+)

REF

REFIN(–)

GND

BAND GAP

REFERENCE

IN-AMPBUF

length), and IOUT1 and IOUT2 match, the error voltage across RL2 equals the error voltage across RL1, and no error voltage is developed between AIN1(+) and AIN1(–). The voltage is developed twice across RL3. However, because this is a common- mode voltage, it does not introduce errors. The reference voltage for the AD7785 is also generated using one of these matched current sources. It is developed using a precision resistor and applied to the differential reference pins of the ADC. This scheme ensures that the analog input voltage span remains ratiometric to the reference voltage. Any errors in the analog input voltage due to the temperature drift of the excitation current are compensated by the variation of the reference voltage.

REFIN(+) REFIN(–)

GND

DOUT/RDY

DIN

SCLK

INTERNAL

CLOCK

Σ-Δ

ADC

SERIAL

INTERFACE

AND

CONTROL

LOGIC

AD7785

CLK

Figure 21. RTD Application Using the AD7785

06721-021

Rev. 0 | Page 30 of 32

AD7785

www.BDTIC.com/ADI

OUTLINE DIMENSIONS

5.10

5.00

4.90

4.50

4.40

4.30

PIN 1

0.15

0.05

0.65

BSC

COPLANARITY

COMPLIANT TO JEDEC STANDARDS MO-153-AB

Figure 22. 16-Lead Thin Shrink S

0.10

0.30

0.19

1.20 MAX

SEATING PLANE

6.40 BSC

0.20

0.09 8°

0°

mall Outline Package [TSSOP]

0.75

0.60

0.45

(RU-16)

Dimensions shown in millimeters

ORDERING GUIDE

Model Temperature Range Package Description Package Option

AD7785BRUZ AD7785BRUZ-REEL EVAL-AD7785EBZ

Z = RoHS Compliant Part.

–40°C to +105°C 16-Lead TSSOP RU-16 –40°C to +105°C 16-Lead TSSOP RU-16

Evaluation Board

Rev. 0 | Page 31 of 32

AD7785

www.BDTIC.com/ADI

NOTES

Rev. 0 | Page 32 of 32

Datasheet AD7785 Datasheet (ANALOG DEIVCES)

Specifications and Main Features

Frequently Asked Questions

User Manual

FEATURES

APPLICATIONS

FUNCTIONAL BLOCK DIAGRAM

GENERAL DESCRIPTION

TABLE OF CONTENTS

REVISION HISTORY

SPECIFICATIONS

TIMING CHARACTERISTICS

TIMING DIAGRAMS

ABSOLUTE MAXIMUM RATINGS

ESD CAUTION

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

OUTPUT NOISE AND RESOLUTION SPECIFICATIONS

EXTERNAL REFERENCE

INTERNAL REFERENCE

TYPICAL PERFORMANCE CHARACTERISTICS

ON-CHIP REGISTERS

COMMUNICATIONS REGISTER

RS2, RS1, RS0 = 0, 0, 0

STATUS REGISTER

RS2, RS1, RS0 = 0, 0, 0; Power-On/Reset = 0x88

MODE REGISTER

RS2, RS1, RS0 = 0, 0, 1; Power-On/Reset = 0x000A

CONFIGURATION REGISTER

RS2, RS1, RS0 = 0, 1, 0; Power-On/Reset = 0x0710

DATA REGISTER

RS2, RS1, RS0 = 0, 1, 1; Power-On/Reset = 0x00000F

ID REGISTER

RS2, RS1, RS0 = 1, 0, 0; Power-On/Reset = 0xXB

IO REGISTER

RS2, RS1, RS0 = 1, 0, 1; Power-On/Reset = 0x00

OFFSET REGISTER

RS2, RS1, RS0 = 1, 1, 0; Power-On/Reset = 0x800000

FULL-SCALE REGISTER

RS2, RS1, RS0 = 1, 1, 1; Power-On/Reset = 0x5XXX00

ADC CIRCUIT INFORMATION

OVERVIEW

DIGITAL INTERFACE

Single Conversion Mode

Continuous Conversion Mode

Continuous Read

CIRCUIT DESCRIPTION

ANALOG INPUT CHANNEL

INSTRUMENTATION AMPLIFIER

BIPOLAR/UNIPOLAR CONFIGURATION

DATA OUTPUT CODING

BURNOUT CURRENTS

EXCITATION CURRENTS

BIAS VOLTAGE GENERATOR

REFERENCE

RESET

AVDD MONITOR

CALIBRATION

GROUNDING AND LAYOUT

APPLICATIONS INFORMATION

TEMPERATURE MEASUREMENT USING A THERMOCOUPLE

TEMPERATURE MEASUREMENT USING AN RTD

OUTLINE DIMENSIONS

ORDERING GUIDE