AMX VTM-D15-A User Manual
instruction manual
VTM-D15/A
15" MultiMedia Touch Panel Systems
To u c h Panels and Accessories
AMX Limited Warranty and Disclaimer
AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for
three (3) years from the date of purchase from AMX Corporation, with the following exceptions:
• Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch
overlay components that are warranted for a period of one (1) year.
• Disk drive mechanisms, pan/tilt heads, power supplies, MX Series products, and KC Series products are
warranted for a period of one (1) year.
• Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year.
• Software is warranted for a period of ninety (90) days.
• Batteries and incandescent lamps are not covered under the warranty.
This warranty extends only to products purchased directly from AMX Corporation or an Authorized AMX Dealer.
AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform.
This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is not
liable for any claim made by a third party or by an AMX Dealer for a third party.
This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort
claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of
liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX
Corporation or an authorized representative of AMX Corporation has been advised of the possibility of any such
damages. This limitation of liability, however, will not apply to claims for personal injury.
Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or
exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of
the Limited Warranty may not apply. This Limited Warranty gives the owner specific legal rights. The owner may
also have other rights that vary from state to state. The owner is advised to consult applicable state laws for full
determination of rights.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES NO
OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX CORPORATION
EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY
IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS
LIMITED WARRANTY.
Table of Contents
Table of Contents
MultiMedia Touch Panel ...........................................................................................1
MultiMedia System Components....................................................................................... 1
VTM-D15/A and VTM-D15/AB Specifications ................................................................... 3
VTM-D15/A and VTM-D15/AB Rear Components ............................................................ 5
AXB-TPI/3 Specifications .................................................................................................. 6
AXB-TPI/3 Components .................................................................................................... 9
VTM-D15/A Sample Configuration .................................................................................. 10
Installation and Wiring ...........................................................................................11
Setting up the AXB-TPI/3 ................................................................................................ 11
Installing the input modules.................................................................................................... 11
Removing input modules........................................................................................................ 11
Mounting the TPI/3 in an equipment rack .............................................................................. 12
Setting up the Panel ........................................................................................................ 12
Table Top Installation (VTM-D15/A and D15/AS) ........................................................... 13
Installing the Table Top support bracket ................................................................................ 13
Connecting the cables on a VTM-D15/A table top panel ....................................................... 15
Surface Mount Installation (VTM-D15/AB and D15/ASB) ............................................... 15
Installing the Surface Mount support bracket......................................................................... 15
Connecting the cables on a VTM-D15/AB surface mount panel ............................................ 17
Wiring the AXB-TPI/3 ...................................................................................................... 18
Preparing captive wires .......................................................................................................... 18
Wiring guidelines.................................................................................................................... 19
Using the AXlink connector for data and power ..................................................................... 19
Using the VGA IN DB-15 (male) high-density connector ....................................................... 20
Connecting the MultiMedia Components ........................................................................ 20
Configuration and Setup ........................................................................................23
VTM-D15/A Startup and Setup Procedures .................................................................... 23
Front Panel buttons and indicators LEDs............................................................................... 23
Setting Up Serial Communication from PC to the TPI/3.................................................. 24
Setting Up Serial procedures ................................................................................................. 24
Using AXCESSX for serial communication ............................................................................ 24
Using HyperTerminal for serial communication ..................................................................... 25
Setting up the VTM-D15/A touch device ................................................................................ 26
Setting the Output Resolution ................................................................................................ 27
Calibrating the Monitor ........................................................................................................... 28
VTM-D15/A 15" MultiMedia Touch Panel Systems
i
Table of Contents
Setting Up AXlink Communication from Master to the TPI/3 .......................................... 28
Setting Up AXlink procedures ................................................................................................ 28
Using AXCESSX for AXlink communication .......................................................................... 29
Using HyperTerminal for AXlink communication.................................................................... 29
Setting up the VTM-D15/A touch device through AXlink........................................................ 29
Setting Up NetLinx Communication from PC to the TPI/3 .............................................. 30
Using NetLinx Studio for communication via an Ethernet connection.................................... 30
Using NetLinx Studio for communication via an COM Port.................................................... 32
Upgrading the TPI/3 Firmware ..............................................................................35
Configuration................................................................................................................... 35
Downloading the Firmware ............................................................................................. 35
On Screen Display (OSD) Features ...................................................................... 37
On Screen Display (OSD) Icons. .................................................................................... 37
Exiting the OSD............................................................................................................... 38
Selecting the Language of the OSD................................................................................ 38
Adjusting Screen Brightness and Contrast ..................................................................... 39
Adjusting Display Performance (Phase and Clock) ........................................................ 39
Adjusting Horizontal and Vertical Screen Position .......................................................... 40
Selecting the Picture Color Temperature ........................................................................ 40
Adjusting Display Color (Red, Green, Blue).................................................................... 41
Adjusting OSD Menu Parameters (OSD Position and Timer)......................................... 41
Adjusting the Picture Sharpness ..................................................................................... 42
Automatic Contrast Adjustment....................................................................................... 43
Optimizing Picture Performance in DOS (Graphic/Text)................................................. 43
Returning (RECALL) to Factory Default Settings............................................................ 44
Exiting the OSD............................................................................................................... 44
Troubleshooting .....................................................................................................45
Display Troubleshooting.................................................................................................. 45
Warning Messages and their Meanings.......................................................................... 46
ii
VTM-D15/A 15" MultiMedia Touch Panel Systems
MultiMedia Touch Panel
The MultiMedia Touch Panel System (VTM-D15/A) comes ready-to-install and ready-to-use, the
MultiMedia system comes in different types of configurations:
•VTM-D15/A • 15" Table Top MultiMedia Touch Panel
•VTM-D15/AB • 15" Surface Mount MultiMedia Touch Panel
MultiMedia Touch Panel
• VTM-D15/AS • 15" Table Top System:
• VTM-D15/ASB • 15" Surface Mount System:
VTM-D15/A, AXB-TPI/3, and TP3-VID
VTM-D15/AB, AXB-TPI/3, TP3-VID, and VTM-WMB
The VTM-D15/A provides an impressive blend of vivid color graphics, sharp icons and seamless
video. The TPD3-VID Video Module allows you to input different video sources, such as VCRs,
Satellites, and DVDs into the TPI/3. The AXB-TPI/3 has three slots on the rear panel that can
contain any combination of three types of input modules: Composite video/S-video (TP3-VID),
RGB (TP3-RGB), and VGA (TP3-VGA). The touch input works via a serial device, such as a serial
mouse or touch monitor. This system can be expanded by purchasing additional TPI/3 modules
such as the TP3-VGA (Graphics), TP3-RGB (RGB input), and additional TP3-VID cards. The
TPI/3 allows the use of any combination of three cards.
MultiMedia System Components
VTM-D15/A 15" MultiMedia Touch Panel
Available in Table Top (VTM-D15/A) or Surface/Wall Mount
(VTM-D15/AB) versions. This touch panel has a wide viewing
angle of up to 160 degrees, crisp color with quality depth/contrast, and an enhanced touch screen overlay. Receives a VGA
signal through either a Composite or S-Video connector port
on the TP3-VID.
AXB-TPI/3 Touch Panel Interface 3
The unit sends graphics to a touch panel of your choice. The
TPI/3 supports up to three scalable windows, which are
driven by plug-in cards for video and computer graphics. The
MultiMedia system comes pre-installed with a TP3-VID Video
Module.
TP3-VID VIdeo Input Module
This input card provides Composite and S-Video connector
ports that can be used to input a variety of video formats from
different video sources. The TPI/3 comes with three available
module slots, by installing a TP3-VID card, this leaves two
other input slots available for use. With additional modules,
you can mix and match any combination of input cards.
Cont.
VTM-D15/A 15" MultiMedia Touch Panel Systems
1
MultiMedia Touch Panel
Powe r A da pt er
Connects to the Power Cord in order to supply power to the
VTM-D15/A touch panel.
Powe r C ord
Connects to the Power Adapter in order to supply power to
the VTM-D15/A touch panel.
15-pin DB15 VGA Signal Cable
Provides a video signal from the video source to the rear of
the VTM-D15/A touch panel.
8-pin Mini Din to 9-pin DB9 Touch Panel Signal Cable
Provides a touchscreen signal from the VTM-D15/A touch
panel to the panel interface.
Touch Screen Support Bracket and screws
(Table Top Panel ONLY)
Provides upright support for the VTM-D15/A touch panel
when placed on a flat level surface.
VTM-WMB Surface Mount Support Bracket and screw
(ONLY available with either the VTM-D15/ASB system or
stand alone VTM-d15/AB Surface Mount Panel)
Provides support for the VTM-D15/A touch panel when
attached to a vertical surface.
DB-9 (on COM1/2)
8-pin mini-DIN
(on rear of panel)
Cont.
2
CD-ROM
Provides the touchscreen drivers that are used with the
touch panel.
VTM-D15/A 15" MultiMedia Touch Panel Systems
Floppy Disk
Provides the computer monitor drivers.
PSN6.5 Power Supply (optional)
The PSN6.5 NetLinx Power Supply distributes switched-mode
12 VDC power @ 6.5 A to up to three AMX devices.
The PSN6.5 supplies power to the AXB-TPI/3 Touch Panel
Interface 3.
Central Controller to AXlink Connection Cable
(optional)
This 4-pin to 4-pin cable connects the Central Controller to
the AXB-TPI/3 Touch Panel Interface.
4-pin captive-wire 4-pin captive-wire
VTM-D15/A and VTM-D15/AB Specifications
MultiMedia Touch Panel
The Surface Mount MultiMedia Panel (VTM-D15/AB) differs from the Table Top MultiMedia
Panel (VTM-D15/A) only in the use of a VTM-WMB Wall Mount bracket that comes with the
Surface Mount unit. The following table lists specifications and describes the front and rear panel
components of the 15" MultiMedia Touch Panels.
Specifications
Dimensions (HWD):
TableTop Panel
Surface Mount Panel
VTM-WMB Bracket
Screen Area Maximum to 1024 x 768 @ 75Hz
Power Consumption • AC: 90 ~ 265 V, 50 ~ 60 Hz
Memory EPROM Chip
Ratings • Safety - UL, CUL, EPA, CB, TUV/BUART, Nordic
Enclosure Metal plate with gray matte finish
On-Screen Properties:
Screens Size 15 inch (38.10 cm) diagonal
Pixel Format 1024 x 768 vertical strip
Pixel Pitch 0.297 mm x 0.297 mm
Brightness 250 cd/m2
Contrast Ratio 300:1
Viewing Angle 160°/160° (minimum)
Color Depth 18-bit
• 14.25" x 15.20" x 6.65" (36.20 cm x 38.60 cm x 16.90 cm)
• 14.75" x 15.20" x 2.87" (37.47 cm x 38.60 cm x 7.30 cm)
• 5.44" x 5.17" x 0.55" (13.82 cm x 13.13 cm x 1.40 cm)
• < 30 W (On), < 8 W (stand-by), and < 5 W (Off)
• EMI - FCC-B, CE
• VESA - DCC1/2B, DPMS
VTM-D15/A 15" MultiMedia Touch Panel Systems
3
MultiMedia Touch Panel
Specifications (Cont.)
Input Signal:
Horizontal Frequency 31 kHz - 60 kHz
Vertical Frequency 50 Hz - 75 Hz
Maximum Pixel Clock 80 MHz
Front Panel Features:
Power Switch Turns the display On and Off
LED Indicator • Lights-up green when the display is turned On
AUTO Button Adjusts the picture position and performance automatically
UP Button Activates the On-Screen Display menu and moves the menu cursor clockwise
DOWN Button Activates the On-Screen Display menu and moves the menu cursor counter-
Increase Button Activates the On-Screen Display menu. Selects the menu items and adjusts
Decrease Button Activates the On-Screen Display menu. Selects the menu items and adjusts
Rear Panel Connectors:
VGA Analog Input 15-pin Mini D-Sub (DB-15) connector for input of VGA signals
TouchScreen Signal Cable 8-pin Mini Din to 9-pin (DB-9) connector for TouchScreen signal communica-
PWR 12 VDC 3-pin AC plug provides power to the display. Supplied by connecting
Fold Switch Locks and unlocks the display into an upright position. The adjustable position
Tilt Angle 10° (degrees from vertical)
User Presets:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Environmental:
Operating Temperature 0° C to 40° C (32° F to 104° F)
Storage Temperature -20° to 50° C (-4° F to 122° F)
Operating Accessories 10% to 90%
Storage Humidity 10% to 90%
Accessories Refer to the MultiMedia System Components section on page 1 for more
• Lights up orange when the display is in power-save mode
to select menu items.
clockwise to select menu items.
their features (increases values).
their features (decreases values).
tion between the panel and computer through COM1 or COM2.
the Power Adapter and Power Cord.
works by using the Support Bracket to fix the visible angle of the TouchScreen.
• 640 x 350 31.5 KHz 70 Hz IBM VGA
• 640 x 480 31.5 KHz 60 Hz IBM VGA
• 640 x 480 35.0 KHz 67 Hz Macintosh
• 640 x 480 37.9 KHz 72 Hz VGA/72
• 640 x 480 37.5 KHz 75 Hz VGA/75
• 720 x 400 31.5 KHz 70 Hz IBM VGA
• 800 x 600 35.2 KHz 56 Hz SVGA/56
• 800 x 600 37.9 KHz 60 Hz SVGA/60
• 800 x 600 48.1 KHz 72 Hz SVGA/72
• 800 x 600 46.9 KHz 75 Hz SVGA/75
• 832 x 624 49.7 KHz 75 Hz Macintosh
• 1024 x 768 48.4 KHz 60 Hz XGA/60
• 1024 x 768 56.5 KHz 70 Hz XGA/70
• 1024 x 768 60.0 KHz 75 Hz XGA/75
information
4
VTM-D15/A 15" MultiMedia Touch Panel Systems
MultiMedia Touch Panel
Specifications (Cont.)
Optional Accessory VTM-WMB: Surface/Wall Mounting Support Bracket
Weight:
VTM-D15/A panel 5.5 kg (12.10 lbs.)
VTM-WMB 2.0 kg (4.40 lbs.)
VTM-D15/A and VTM-D15/AB Rear Components
FIG. 1 shows the rear components of the VTM-D15/A 15" Table Top MultiMedia Panel.
12 VDC
input VGA input
Fold switch
Touch Screen
Signal cable
100 V~
240 V~
AC input
FIG. 1 Rear component connection locations on the VTM-D15/A
Powe r
adapter
FIG. 2 shows the rear components of the VTM-D15/AB 15" Surface Mount MultiMedia Panel.
12 VDC
input
VTM-WMB
Wall Mount
Bracket
Power Adapter
VGA Input cable - connects from panel
to Monitor Out port on TPI/3
Touch Screen cable - connects
from panel to Mouse Port on TPI/3
12 VDC connector - routes
power from the power cord and
adapter
FIG. 2 Rear component connection locations on the VTM-D15/AB
VTM-D15/A 15" MultiMedia Touch Panel Systems
5
MultiMedia Touch Panel
AXB-TPI/3 Specifications
The following table lists the specifications for the AXB-TPI/3 and its related input modules.
Specifications
Dimensions (HWD): 3.47" x 13.75" x 8.38" (8.81 cm x 34.93 cm x 21.29 cm)
Front Panel:
Output Resolution LEDs 3 red LEDs indicate the output video resolution:
AXlink LED Green LED indicates AXlink status. AXlink LED blinks to indicate the communi-
Program Port 4-pin AXlink data/power bus jack. This port is an RS-232 DB-9 connector
Touch Drivers Downloadable touch drivers allow you to add to the standard list of available
Current Consumption • 630 mA - with no input modules (cards) only supplying power to the TPI/3
Memory Standard 9 MB (8 MB flash)
Font Support Unicode font support. Buttons with Unicode fonts can only be created and
Slots Equipped with any combination of input modules (S-Video/Composite, VGA,
Outputs VGA, HD-15, and RGB 5-BNC
• With brackets installed for rack-mounting: 3.47" x 19.00" x 8.38"
(8.81 cm x 48.26 cm x 21.29 cm)
• With brackets rotated 45° for under/over/vertical surface mounting:
3.85" x 19.00" x 8.38" (9.78 cm x 48.2 cm x 21.29 cm)
• VGA LED - VGA output display resolution LED lights to indicate an active 640
x 480 (HV) resolution.
• SVGA LED - SVGA output display resolution LED lights to indicate an active
800 x 600 (HV) resolution.
• XGA LED - XGA output display resolution LED lights to indicate an active
1024 x 768 (HV) resolution.
cation activity, power, and data status:
• One blink per second: Power is active and AXlink data communication is
functional.
• Full On: Power is active and AXlink data communication is not functional.
(male) that can be connected to a DB-9 port on a PC; used with serial commands, SoftROM downloads, other DB-9 capable panels, and to upload/download touch panel page information from the TPDesign3 program.
drivers. Currently supports devices such as the VTM-D15/A and
Elo Intellitouch
• 1.13 A - with 1 input module/card - 500 mA input module
• 1.63 A - with 2 input modules/card - 500 mA input module
• 2.13 A - with 3 input modules/card - 500 mA input module
edited with the TPDesign3 Touch Panel Program (Version 3.16 or higher).
and RGB).
®
touch monitors.
6
VTM-D15/A 15" MultiMedia Touch Panel Systems
MultiMedia Touch Panel
Specifications (Cont.)
Rear Panel Components:
TP3-VID (default card) Use the TP3-VID input module in any input slot to connect video sources, such
TP3-RGB (optional) Use the TP3-RGB input module in any input slot to connect RGB-type sources.
TP3-VGA (optional) Use the TP3-VGA input module in any input slot to connect VGA-type sources
Mouse Port RS-232 (DB-9) 9-pin serial port. The 9-pin serial port is used to connect a
Monitor Out (VGA) HD-15 VGA output connector. The AXB-TPI/3 contains two types of GUI output
Monitor Out (RGB) RGB connection is done by using the five BNC output connectors (from left to
as VCRs and DVDs. The module is secured by two black thumbscrews.
• Composite LED indicator (turns on when composite video input is detected).
The Composite video input types are: NTSC, SECAM, or PAL.
• Composite input connector
• S-Video LED indicator (turns on when S-Video input is detected).
• S-Video input connector
• 500 mA power consumption
The module is secured by two black thumbscrews.
• 5-BNC input connectors: R (Red), G (Green), B (Blue), H/HV (Horizontal/
Composite sync), V (Vertical sync)
• 500 mA power consumption
The TP3-RGB input module accepts the following configurations:
• Red, green, blue, horizontal sync, vertical sync
• Red, green, blue, composite sync (on H/HV connector)
• Red, green, blue, with sync on green signal
To achieve the best video quality on the VGA and RGB modules, use an alternating pixel pattern to fine tune the picture.
(common for PCs). The module is secured by two black thumbscrews.
• One HD-15 input connector
• 500 mA power consumption
The TP3-VGA input module accepts the following configurations:
• Red, green, blue, horizontal sync, vertical sync
• Red, green, blue, composite sync
• Red, green, blue, with sync on green signal
pointer device, such as a serial mouse. The AXB-TPI/3 also supports several
external serial touch devices such as some touch pads, touch-sensitive
monitors, and tablets. Refer to FIG. 3 on page 9 for more information.
connectors: DB15 and 5-BNC RGB output connectors. VGA connection is
done through the use of the VGA (HD-15) monitor output for VGA-type monitors (common to PCs). Connect the VGA output monitor's HD-15 (female) connector to the VGA connector (male) on the rear panel of the AXB-TPI/3.
right) red (R), green (G), blue (B), horizontal sync (H), and vertical sync (V).
Connect the RGB output monitor's 5-BNC connectors to the RGB connectors
on the rear panel of the AXB-TPI/3.
• RGB (5-BNC) output connectors
• Red, Green, Blue, Horizontal Sync, Vertical Sync
VTM-D15/A 15" MultiMedia Touch Panel Systems
7
MultiMedia Touch Panel
Specifications (Cont.)
Input resolution and refresh
rates per resolution (RGB
and VGA only)
TPI/3 Programming • Serial connection: Connect a DB-9 cable from your PCCOM port to the
Included Accessories • Two rack-mount ears and a package of rack screws
Optional • PSN6.5 power supply (12 VDC)
Input resolution and refresh
rates per resolution (RGB
and VGA only)
TPI/3 Programming • Serial connection: Connect a DB-9 cable from your PCCOM port to the
Included Accessories • Two rack-mount ears and a package of rack screws
Weight 4.85 lbs (2.20 kg)
• 640 x 480 (VGA): 60 Hz, 72 Hz, 75 Hz, 85 Hz
• 800 x 600 (SVGA): 56 Hz, 60 Hz, 72 Hz, 75 Hz
• 1024 x 768 (XGA): 60 Hz, 70 Hz, 75 Hz, 85 Hz
Program port located on the front of the AXB-TPI/3. This is the only method
of programming the TPI/3 using Serial Commands.
• AXlink connection: Connect a DB-9 cable from your PCCOM port to the
Programming port on the Controller. Then use an AXlink cable to connect the
AXlink connector on the Controller to the AXlink connector at the rear of the
AXB-TPI/3. This is the only method of programming the interface unit using
Send_Commands.
• One 4-pin AXlink connector
• One 2-pin PWR connector
• Input module (TP3-VID, TP3-RGB, and TP3-VGA)
• 640 x 480 (VGA): 60 Hz, 72 Hz, 75 Hz, 85 Hz
• 800 x 600 (SVGA): 56 Hz, 60 Hz, 72 Hz, 75 Hz
• 1024 x 768 (XGA): 60 Hz, 70 Hz, 75 Hz, 85 Hz
Program port located on the front of the AXB-TPI/3. This is the only method
of programming the TPI/3 using Serial Commands.
• AXlink connection: Connect a DB-9 cable from your PCCOM port to the
Programming port on the Controller. Then use an AXlink cable to connect the
AXlink connector on the Controller to the AXlink connector at the rear of the
AXB-TPI/3. This is the only method of programming the interface unit using
Send_Commands.
• One 4-pin AXlink connector
• One 2-pin PWR connector
8
VTM-D15/A 15" MultiMedia Touch Panel Systems
MultiMedia Touch Panel
AXB-TPI/3 Components
FIG. 3 shows the front and rear components of the AXB-TPI/3 Touch Panel Interface 3.
Rack-mounting brackets
Front View
Slot 3
(shown with
optional
TP3-VGA module)
TP3-VGA
Rear View
Mouse port
(connection
to TouchScreen
signal cable
SLOT 3
VGA
Monitor Out
to VTM-D15/A
(VGA-HD15)
(5 BNC) controlling
FIG. 3 AXB-TPI/3 (front and rear views)
VGA output LED
SVGA output LED
XGA output LED
AXlink LED
Slot 2
(shown with optional
TP3-RGB module)
TP3-RGB
SLOT 2 SLOT 1
R
GH/HVB V
MONITOR
OUT
Monitor Out
RGBHV
VGA SVGA AXlinkXGA
TP3-VID
COMP Y/C
R G HB V
PROGRAM
PORT
DB-9 Program Port
Slot 1
(shown with default
TP3-VID module)
12VDC
AXP
AXM
GND
PWR
AXlink
PWRMOUSE PORT
12 VDC
power connector
AXlink
connector
VTM-D15/A 15" MultiMedia Touch Panel Systems
9
MultiMedia Touch Panel
VTM-D15/A Sample Configuration
FIG. 4 shows a sample Table Top MultiMedia System application using a TPI/3, touch panel,
computer (used to configure the TPI/3), and Central Controller.
External Power
(Adapter and Cord)
AMX AXB-TPI/3 (front view)
VTM-D15/A
MultiMedia
To u ch
Panel
DB-9 to 8-pin mini-DIN
15-pin VGA cable
AMX AXB-TPI/3 (rear view)
(showing optional input cards)
DB-9 connecting
Program Port from
TPI/3 to COM1/2
on rear of computer
Computer
FIG. 4 Sample MultiMedia Touch Panel System Configuration
AXlink 4-pin
connection to
Master Controller
2-pin captive-wire
AMX PSN6.5
Power Supply
Power to the VTM-D15/A touch panel is supplied through an external power supply. Power to the
TPI/3 can be supplied either directly through a PSN6.5 or indirectly through an AXlink cable
connection from a Central Controller. The power source is dependant on the distance between the
TPI/3 and the Central Controller. If the distance between the two is greater than outlined in the
Wiring the AXB-TPI/3 section on page 18, a local power source (like the PSN6.5) must be used.
10
VTM-D15/A 15" MultiMedia Touch Panel Systems
Installation and Wiring
This section covers the steps necessary to setup the individual MultiMedia components and connect
them together. The three areas of focus ar the main component setup, wiring, installation, and
connection.
Setting up the AXB-TPI/3
The AXB-TPI/3 does not come pre-installed with any input modules. The card provided with the
original system package is the TP3-VID Composite/S-Video Input Module. The TPI/3 can be
configured with any combination of 3 input cards (TP3-RGB, TP3-VGA, and/or TP3-VID).
Installing the input modules
1. Discharge the static electricity from your body by touching a grounded metal object.
Always power down the TPI/3 before attempting to remove or install input modules.
Failure to do so could result in damage to the TPI/3 and/or input modules.
Installation and Wiring
2. Disconnect any connectors from the AXB-TPI/3.
3. Remove (counter-clockwise) the two-black thumbscrews on the slot cover corresponding to the
location being used for the inserted input module. Any module can be inserted into any slot
number.
4. Gently insert the module into the brackets inside the card slot and slide the input module into
the enclosure until you feel it contact the slot connector, as shown in FIG. 5.
FIG. 5 Inserting an input module
5. Screw in (clockwise) the two thumbscrews to secure the module.
6. Repeat steps 3 through 5 to insert other input modules, if necessary.
Removing input modules
1. Disconnect any power supply connected to the TPI/3.
Always power down the TPI/3 before attempting to remove or install input modules.
Failure to do so could result in damage to the TPI/3 and/or input modules.
VTM-D15/A 15" MultiMedia Touch Panel Systems
11
Installation and Wiring
2. Discharge the static electricity from your body by touching a grounded metal object.
3. Disconnect any other connectors from the TPI/3 input module.
4. Remove (counter-clockwise) the two black thumbscrews on the input module.
5. Slide the module out of the enclosure.
6. Repeat steps 4 and 5 for other slots, as required.
7. Ensure that all thumbscrews are secured and reconnect all rear panel connectors.
Mounting the TPI/3 in an equipment rack
Use the supplied mounting brackets for 19" equipment rack installations. Remove the mounting
brackets for flat surface installations. You will need a Phillips screwdriver to install the TPI/3.
To install the AXB-TPI/3 in an equipment rack:
1. Discharge the static electricity from your body by touching a grounded metal object.
2. Install the mounting brackets using the screws supplied with the unit, as shown in FIG. 6.
12
FIG. 6 Installing mounting brackets
3. With the rack mount brackets installed, place the AXB-TPI/3 into the equipment rack, and
align the mounting bracket holes with the mounting holes on the equipment rack. Start the
mounting screws on both sides of the controller and tighten.
4. Thread the incoming AXlink, power cable (optional) and VTM-D15/A (DB-15 video and
Touch Screen signal cables) through the opening in the equipment rack. Refer to the
Configuration and Setup section on page 23 for more detailed information.
Setting up the Panel
The setup of the MultiMedia Touch Panel involves unpacking the unit, attaching the particular type
of panel support (Table Top or Surface Mount), and connecting the appropriate cables.
1. Remove the panel from the shipping case.
2. Lay the back of the panel on a flat surface.
3. Remove the dust-proof plastic sheet (FIG. 7) from the screen (if applicable).
VTM-D15/A 15" MultiMedia Touch Panel Systems
Loading...