AMX RDD-DM6 User Manual

Installation Sheet

RDD-DM6 6-Channel Integrated Dimmer Module 120,240,277 VAC

The RDD-DM6 Six-Channel Integrated Dimmer Module controls up to six dimmed channels with six onboard 10 A dimmers. The RDD-DM6 is designed for use with the RDA series of enclosures, in a AMX Lighting™ modular digital dimming system. The RDD-DM6 is controlled by AXlink, PROlink, or by dry (contact) closures. The RDD-DM6's 120, 240, and 277 VAC ratings are CE, UL, and C-UL approved.

5.87" (149 mm)

Mounting points

Dimmers

Bridge

High

voltage

connections

Load out

10.00"

(254.00 mm)

Mounting points

DRY CLOSURES

AXlink connector

PROlink connector

External +12V power

connector (optional)

Neutral

Chokes

AXlink address DIP switch

PROlink address DIP switch

RESET button

MEMORY PROTECT jumper

FIG. 1 RDD-DM6 6-channel Integrated Dimmer Module

RDD-DM6 UL and C-UL Ratings (per circuit)

Input

• 120, 240, 277 VAC, single phase, 3-wire, 50/60 Hz, 2400 W, one feed

• 120, 240, 277 VAC, single phase, 4-wire, 50/60 Hz, 4800 W, two feed

Output

• 1200 W max. per channel @120, 240, 277 VAC

• 2400 W max. total, all six channels on with 2400 W feed

• 4800 W max. total, all six channels on with dual 2400 W feeds

• Feed circuit #1 goes to dimmer 1, 3, and 5; feed circuit #2 goes to dimmer 2, 4 and 6

Suggested Switched Loads

• Incandescent

• Low-voltage

• Neon, cold-cathode

• Motors

• Fans

Specifications

• Dimensions (HW): 5.87" x 10.0" (149.00 mm x 254.00 mm)

• Use wires rated at 75°C (167°F)

• Torque terminals to 20 in-lbs (2.3 N/M)

• Max. wire size: 10 AWG (4 mm²)

• Wire stripping length: 0.28" (7 mm)

• Weight: 4.5 lbs (2.04 kg)

•BTU/hr: 300 single feed (2400 W); 600 dual feed (4800 W)

• Power consumption: 50 mA @ 120 VAC, 25 mA @ 240 VAC, 22 mA @ 277 VAC

• Control port current: 200 mA @ 12 VDC

Caution: Pre-Installation Notes

• All Class 1 wiring must be connected to proper terminals.

• All control wiring must be connected to proper terminals.

• Disconnect power while installing or connecting the unit.

• Keep top and bottom air vents clear at all times.

• Test loads for shorts before connecting.

• Use low-voltage wires with a 300 volt rating or greater.

• Use field installed copper conductors.

• All electrical ratings are for continuous duty.

• For indoor use only.

• This module may require extra power from the AXlink connection or an external power supply connected to the control card.

Connecting AXlink:

Connect the 4-pin captive-wire AXlink from the RDD-DM6 to the Central Controller for AXlink control of the dimming system.

(optional)

RDD-DM6

PWR

AXP AXM

GND

PWR AXP

AXM GND

Central Controller

FIG. 2 Connecting AXlink

Connecting PROlink:

Connect the orange 4-pin captive-wire PROlink connector from the RDD-DM6 to a PRO-DP8 PROlink wall panel.

PRO-DP8 Pack 1 Pack 2

+12

PR+ PR-

GND

+12

PR+ PR-

GND

FIG. 3 Connecting PROlink

Line-in Connections:

20 A

FIG. 4 Line-in Connections

Dual 2400 W Inputs

Bridged 2400 W Input

Using two feeds for line 1 and line 2 provides two, 2400 W inputs.

Bridging line 1 and line 2 provides a single 2400 W input.

Connecting Dry Closures:

Use the 8 (+ common) dry closures with a WPD8 eight-button wall panel.

COM

Each contact (1 - 8) is preprogrammed with a default preset.

Refer to the AMX Lighting Control System instruction manual for details on dry closure default presets and recording new presets.

FIG. 5 Dry closures connection

Lighting Application Drawings

Setting AXlink and PROlink Address Numbers:

AXlink Address PROlink Address

Set the AXlink address number (1-255) for the RDD-DM6. This number must match the device number in your Axcess program.

Use the PROlink DIP switch to set the PROlink address number for the RDD-DM6 (1-10).

Pin 8 on the PROlink DIP switch is a test switch that turns all circuits on to full.

FIG. 6 Setting AXlink and PROlink address numbers

Method A

120 VAC 1Ø /

Single-phase, six load

Te st

FIG. 7 Method A

FIG. 8 Method B

Method B

120/208-240 VAC 1Ø /

Single-phase, six load

AMX Corporation reserves the right to alter specifications without notice at any time.

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

The AMX logo is a trademark of AMX Corporation. AMX reserves the right to alter specifications without notice at any time.

3000 research drive, richardson, TX 75082 USA • 469.624.8000 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993