AMX NXD-700Vi User Manual

Operation/Reference Guide

Modero® NXD-700Vi

G4 Touch Panels

7” Modero Widescreen Video Touch Panels

with Full Duplex Intercom

Touch Panels

Last Revised: 10/10/2008

AMX Limited Warranty and Disclaimer

All products returned to AMX require a Return Material Authorization (RMA) number. The RMA number is
obtained from the AMX RMA Department. The RMA number must be clearly marked on the outside of each
box. The RMA is valid for a 30-day period. After the 30-day period the RMA will be cancelled. Any shipments
received not consistent with the RMA, or after the RMA is cancelled, will be refused. AMX is not responsible
for products returned without a valid RMA number.

Warranty Repair Policy

• AMX will repair any defect due to material or workmanship issues during the applicable warranty period at no cost to the AMX
Authorized Partner., provided that the AMX Authorized Partner is responsible for in-bound freight and AMX is responsible for
out-bound ground freight expenses.

• The AMX Authorized Partner must contact AMX Technical Support to validate the failure before pursuing this service.

• AMX will complete the repair and ship the product within five (5) business days after receipt of the product by AMX. The AMX
Authoized Partner will be notified if repair cannot be completed within five (5) business days.

• Products repaired will carry a ninety (90) day warranty or the balance of the remaining warranty, whichever is greater.

• Products that are returned and exhibit signs of damage or unauthorized use will be processed under the Non-Warranty Repair
Policy.

• AMX will continue to provide Warranty Repair Services for products discontinued or replaced by a Product Discontinuance
Notice.

Non-Warranty Repair Policy

• Products that do not qualify to be repaired under the Warranty Repair Policy due to age of the product or Condition of the prod­uct may be repaired utilizing this service.

• The AMX Authorized Partner must contact AMX Technical Support to validate the failure before pursuing this service.

• Non-warranty repair is a billable service.

• Products repaired under this policy will carry a ninety (90) day warranty on material and labor.

• AMX will notify the AMX Authorized Partner with the cost of repair, if cost is greater than the Standard Repair Fee, within five (5)
days of receipt.

• The AMX Authorized Partner must provide a Purchase Order or credit card number within five (5) days of notification, or the
product will be returned to the AMX Authorized Partner.

• The AMX Authorized Partner will be responsible for in-bound and out-bound freight expenses.

• Products will be repaired within ten (10) business days after AMX Authorized Partner approval is obtained.

• Non-repairable products will be returned to the AMX Authorized Partner with an explanation.

• See AMX Non-Warranty Repair Price List for minimum and Standard Repair Fees and policies.

Software License and Warranty Agreement

• LICENSE GRANT. AMX grants to Licensee the non-exclusive right to use the AMX Software in the manner described in this
License. The AMX Software is licensed, not sold. This license does not grant Licensee the right to create derivative works of the
AMX Software. The AMX Software consists of generally available programming and development software, product documenta­tion, sample applications, tools and utilities, and miscellaneous technical information. Please refer to the README.TXT file on
the compact disc or download for further information regarding the components of the AMX Software. The AMX Software is sub­ject to restrictions on distribution described in this License Agreement. AMX Dealer, Distributor, VIP or other AMX authorized
entity shall not, and shall not permit any other person to, disclose, display, loan, publish, transfer (whether by sale, assignment,
exchange, gift, operation of law or otherwise), license, sublicense, copy, or otherwise disseminate the AMX Software. Licensee
may not reverse engineer, decompile, or disassemble the AMX Software.

• ACKNOWLEDGEMENT. You hereby acknowledge that you are an authorized AMX dealer, distributor, VIP or other AMX autho­rized entity in good standing and have the right to enter into and be bound by the terms of this Agreement.

• INTELLECTUAL PROPERTY. The AMX Software is owned by AMX and is protected by United States copyright laws, patent
laws, international treaty provisions, and/or state of Texas trade secret laws. Licensee may make copies of the AMX Software
solely for backup or archival purposes. Licensee may not copy the written materials accompanying the AMX Software.

• TERMINATION. AMX RESERVES THE RIGHT, IN ITS SOLE DISCRETION, TO TERMINATE THIS LICENSE FOR ANY REA­SON UPON WRITTEN NOTICE TO LICENSEE. In the event that AMX terminates this License, the Licensee shall return or
destroy all originals and copies of the AMX Software to AMX and certify in writing that all originals and copies have been
returned or destroyed.

• PRE-RELEASE CODE. Portions of the AMX Software may, from time to time, as identified in the AMX Software, include PRE­RELEASE CODE and such code may not be at the level of performance, compatibility and functionality of the GA code. The
PRE-RELEASE CODE may not operate correctly and may be substantially modified prior to final release or certain features may
not be generally released. AMX is not obligated to make or support any PRE-RELEASE CODE. ALL PRE-RELEASE CODE IS
PROVIDED "AS IS" WITH NO WARRANTIES.

• LIMITED WARRANTY. AMX warrants that the AMX Software (other than pre-release code) will perform substantially in accor­dance with the accompanying written materials for a period of ninety (90) days from the date of receipt. AMX DISCLAIMS ALL
OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH REGARD TO THE AMX SOFTWARE. THIS LIM­ITED WARRANTY GIVES LICENSEE SPECIFIC LEGAL RIGHTS. Any supplements or updates to the AMX SOFTWARE,
including without limitation, any (if any) service packs or hot fixes provided to Licensee after the expiration of the ninety (90) day
Limited Warranty period are not covered by any warranty or condition, express, implied or statutory.

• LICENSEE REMEDIES. AMX's entire liability and Licensee's exclusive remedy shall be repair or replacement of the AMX Soft­ware that does not meet AMX's Limited Warranty and which is returned to AMX in accordance with AMX's current return policy.
This Limited Warranty is void if failure of the AMX Software has resulted from accident, abuse, or misapplication. Any replace­ment AMX Software will be warranted for the remainder of the original warranty period or thirty (30) days, whichever is longer.
Outside the United States, these remedies may not available. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO
EVENT SHALL AMX BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER
PECUNIARY LOSS) ARISING OUT OF THE USE OF OR INABILITY TO USE THIS AMX SOFTWARE, EVEN IF AMX HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES/COUNTRIES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITA­TION MAY NOT APPLY TO LICENSEE.

• U.S. GOVERNMENT RESTRICTED RIGHTS. The AMX Software is provided with RESTRICTED RIGHTS. Use, duplication, or
disclosure by the Government is subject to restrictions as set forth in subparagraph ©(1)(ii) of The Rights in Technical Data and
Computer Software clause at DFARS 252.227-7013 or subparagraphs ©(1) and (2) of the Commercial Computer Software
Restricted Rights at 48 CFR 52.227-19, as applicable.

• SOFTWARE AND OTHER MATERIALS FROM AMX.COM MAY BE SUBJECT TO EXPORT CONTROL. The United States
Export Control laws prohibit the export of certain technical data and software to certain territories. No software from this Site may
be downloaded or exported (i) into (or to a national or resident of) Cuba, Iraq, Libya, North Korea, Iran, Syria, or any other coun­try to which the United States has embargoed goods; or (ii) anyone on the United States Treasury Department's list of Specially
Designated Nationals or the U.S. Commerce Department's Table of Deny Orders. AMX does not authorize the downloading or
exporting of any software or technical data from this site to any jurisdiction prohibited by the United States Export Laws.

This Agreement replaces and supersedes all previous AMX Software License Agreements and is governed by
the laws of the State of Texas, and all disputes will be resolved in the courts in Collin County, Texas, USA. For
any questions concerning this Agreement, or to contact AMX for any reason, please write: AMX License and
Warranty Department, 3000 Research Drive, Richardson, TX 75082.

FCC Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received; including interference
that may cause undesired operation.

Federal Communications Commission (FCC)
Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure Statement

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This
equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed an operated with a minimum distance of 20 centimeters between the radiator and your body.

Table of Contents

Table of Contents

Introduction ........................................................................................................1

NXD-700Vi Specifications ......................................................................................... 3

NXD-700Vi Panels - Connector Layout ..................................................................... 6

NXA-AVB/ETHERNET Breakout Box ...................................................................7

Product Specifications ............................................................................................. 8

Installing the NXA-AVB/ETHERNET .......................................................................... 8

Wiring the NXA-AVB/ETHERNET connectors and cables.......................................... 9

Wiring the NXA-AVB/ETHERNET for Unbalanced Audio ........................................ 11

Wiring the NXA-AVB/ETHERNET for Balanced Audio ............................................ 11

NXD-700Vi Touch Panel Accessories .................................................................. 1

NXA-WC80211B/CF 802.11b Wireless Card (FG2255-03) ........................................ 1

NXA-WC80211GCF 802.11g Wireless Card (FG2255-07) ......................................... 2

NXA-CFSP Compact Flash (FG2116-7x) ..............................................................7

Installation and Upgrade of the Internal NXD Components ...............................9

Step 1: Remove the existing NXD Outer Housing .................................................... 9

Step 2: Install the new Compact Flash Memory card .............................................. 10

Step 3: Close and Resecure the NXD Panel Enclosure............................................ 11

Installation ........................................................................................................13

Installing the No-Button Trim Ring ......................................................................... 13

Installing the Button Trim Ring ............................................................................... 14

Pre-Wall Installation of the Conduit Box................................................................. 16

Installation of an NXD Touch Panel......................................................................... 17

Installing the NXD panel within a Conduit Box ............................................................. 17

Installing the NXD into drywall using Expansion Clips .................................................. 18

Installing the NXD into a Flat Surface using #4 screws ................................................. 21

Installing an NXD-700Vi into an (optional) Rack Mount Kit (NXA-RK7)......................... 23

Wiring Guidelines for the NXD-700Vi Panels.......................................................... 24

Preparing captive wires................................................................................................. 24

Wiring a power connection ........................................................................................... 24

Audio/Video Port: Connections and Wiring............................................................ 25

Ethernet/RJ-45 Port: Connections and Wiring ........................................................ 25

USB Port: Connecting and Using Input Devices ...................................................... 26

Panel Calibration ..............................................................................................27

Calibrating the Modero Panel................................................................................. 27

Testing your Calibration................................................................................................ 28

7" Modero Widescreen Touch Panels

i

Table of Contents

If Calibration Is Not Working......................................................................................... 29

Configuring Communication .............................................................................31

Modero Setup and System Settings ....................................................................... 31

Accessing the Setup and Protected Setup Pages.......................................................... 31

Setting the Panel’s Device Number............................................................................... 32

Wireless Settings Page - Wireless Access Overview ............................................... 32

Hot Swapping................................................................................................................ 32

Configuring a Wireless Network Access ................................................................. 33

Step 1: Configure the Panel’s Wireless IP Settings ................................................. 33

Wireless communication using a DHCP Address ........................................................... 33

Wireless communication using a Static IP Address........................................................ 34

Using the Site Survey tool............................................................................................. 34

Step 2: Configure the Card’s Wireless Security Settings ........................................ 36

Configuring the Modero’s wireless card for unsecured access to a WAP200G............. 37

Configuring the Modero’s wireless card for secured access to a WAP200G................. 39

Automatically set SSID .................................................................................................. 39

Manually set SSID.......................................................................................................... 40

Configuring multiple wireless Moderos to communicate to a target WAP200G........... 43

Step 3: Choose a Master Connection Mode ........................................................... 43

USB................................................................................................................................ 43

Prepare your PC for USB communication with the panel .............................................. 44

Configure the panel for USB communication ................................................................ 44

Configure a Virtual NetLinx Master using NetLinx Studio............................................. 45

Ethernet ........................................................................................................................ 47

Master Connection to a Virtual Master via Ethernet ..................................................... 47

Using G4 Web Control to Interact with a G4 Panel ................................................ 50

Using your NetLinx Master to control the G4 panel ............................................... 52

Upgrading Modero Firmware ...........................................................................55

Upgrading the Modero Firmware via the USB port ................................................ 55

Step 1: Configure the panel for a USB Connection Type .............................................. 55

Step 2: Prepare NetLinx Studio for communication via the USB port........................... 56

Step 3: Confirm and Upgrade the firmware via the USB port....................................... 57

Upgrading the Modero Firmware via Ethernet (IP Address) ................................... 59

Step 1: Prepare the Master for communication via an IP .............................................. 59

Step 2: Prepare the panel for communication via an IP................................................. 60

Step 3: Verify and Upgrade the panel firmware via an IP ............................................. 61

Firmware Pages and Descriptions ....................................................................63

Setup Navigation Buttons ....................................................................................... 63

Protected Setup Page ................................................................................................... 63

ii

7" Modero Widescreen Touch Panels

Table of Contents

Setup Page ............................................................................................................. 64

Information ............................................................................................................. 65

Project Information Page .............................................................................................. 66

Panel Information Page................................................................................................. 67

Time & Date Setup Page............................................................................................... 69

Volume Page................................................................................................................. 70

Supported sampling rates for WAV .............................................................................. 72

Video Adjustment Page ................................................................................................ 72

Protected Setup Navigation Buttons ...................................................................... 74

Protected Setup Page............................................................................................. 75

System Settings Page.................................................................................................... 77

Wireless Settings Page.................................................................................................. 79

Secondary Connection Page ......................................................................................... 82

Wireless Security Page.................................................................................................. 82

Open (Clear Text) Settings............................................................................................ 83

Static WEP Settings....................................................................................................... 84

WPA-PSK Settings......................................................................................................... 86

EAP-LEAP Settings........................................................................................................ 88

EAP-FAST Settings ........................................................................................................ 90

EAP-PEAP Settings........................................................................................................ 92

EAP-TTLS Settings......................................................................................................... 94

EAP-TLS Settings........................................................................................................... 96

Client certificate configuration...................................................................................... 97

Calibration Page............................................................................................................ 99

G4 Web Control Page................................................................................................. 100

Sensor Setup............................................................................................................... 102

Making the most of the Automated Brightness Control feature (DIM Mode)............. 104

Other Settings ...................................................................................................... 105

Image Caching Page.................................................................................................... 106

Setting the image cache.............................................................................................. 108

Clearing the image cache............................................................................................ 108

Checking image cache status ...................................................................................... 108

Password Setup Page.................................................................................................. 108

SIP Settings Page ........................................................................................................ 109

Tools ..................................................................................................................... 111

Panel Logs Page.......................................................................................................... 111

Checking the Panel Connection Logs .......................................................................... 112

Refreshing the Panel Connections Log........................................................................ 112

Clearing the Panel Connections Log ........................................................................... 112

Panel Statistics Page ................................................................................................... 112

7" Modero Widescreen Touch Panels

iii

Table of Contents

Checking the Panel Statistics....................................................................................... 114

Refreshing the Panel Statistics .................................................................................... 114

Clearing the Panel Statistics........................................................................................ 114

Connection Utility Page............................................................................................... 114

Using the Connection Utility........................................................................................ 116

EAP Security & Server Certificates .................................................................117

Overview .............................................................................................................. 117

Full Duplex Intercom ......................................................................................119

Overview .............................................................................................................. 119

Incorporating an intercom capable panel into your NetLinx

system................................................................................................................ 119

Panel Intercom Configuration ............................................................................... 119

Setup........................................................................................................................... 119

Setting the Intercom Session Timeout......................................................................... 120

Setting Intercom Auto Answer.................................................................................... 120

Advanced Setup .......................................................................................................... 121

Allowing a panel to be monitored............................................................................... 121

Allowing a panel to monitor........................................................................................ 122

Naming a panel ........................................................................................................... 122

Sample Intercom Page .......................................................................................... 123

Answering an incoming call ......................................................................................... 125

Creating Intercom Pages ...................................................................................... 126

Programming ..................................................................................................127

Overview .............................................................................................................. 127

Button Assignments ............................................................................................. 127

Page Commands ................................................................................................... 127

Programming Numbers......................................................................................... 133

RGB triplets and names for basic 88 colors ................................................................ 133

Font styles and ID numbers......................................................................................... 135

Border styles and Programming numbers ................................................................... 136

"^" Button Commands ......................................................................................... 138

Text Effects Names ............................................................................................... 157

Button Query Commands ..................................................................................... 158

Panel Runtime Operations .................................................................................... 167

Input Commands................................................................................................... 172

Embedded codes .................................................................................................. 174

Panel Setup Commands ........................................................................................ 175

Dynamic Image Commands................................................................................... 178

Panel Intercom Commands ................................................................................... 180

iv

7" Modero Widescreen Touch Panels

Table of Contents

SIP Commands ...................................................................................................... 181

Appendix A: Text Formatting .........................................................................185

Text Formatting Codes for Bargraphs/Joysticks................................................... 185

Text Area Input Masking....................................................................................... 186

Input mask character types ......................................................................................... 186

Input mask ranges....................................................................................................... 187

Input mask next field characters ................................................................................. 187

Input mask operations................................................................................................. 187

Input mask literals ....................................................................................................... 187

Input mask output examples....................................................................................... 188

URL Resources ...................................................................................................... 189

Special escape sequences ........................................................................................... 189

Appendix B - Wireless Technology .................................................................191

Overview of Wireless Technology......................................................................... 191

Terminology.......................................................................................................... 192

EAP Authentication............................................................................................... 195

EAP characteristics...................................................................................................... 195

EAP communication overview..................................................................................... 196

AMX Certificate Upload Utility ............................................................................. 197

Configuring your G4 Touch Panel for USB Communication .................................. 197

Step 1: Setup the Panel and PC for USB Communication ........................................... 197

Step 2: Confirm the Installation of the USB Driver on the PC ..................................... 198

How to Upload a Certificate File .......................................................................... 199

Appendix C: Troubleshooting ........................................................................203

7" Modero Widescreen Touch Panels

v

Table of Contents

vi

7" Modero Widescreen Touch Panels

Introduction

The NXD-700Vi Modero Widescreen Color Video Touch Panels with duplex intercom (FIG. 1) are the
industry’s first widescreen mini-touch panels and are available only through AMX.

Introduction

FIG. 1 Sample 7" Video Touch Panels

These Color Video (CV) panels display NTSC/PAL/SECAM video formats within variable sized
windows. They include a built-in microphone, speaker, audio/headphone connector, and six NetLinx
programmable pushbuttons (available on NXD models only when mounted with included Button Trim
Ring).

Each panel is sold only as part of a kit which includes both a panel and an NXA-AVB/ETHERNET
Audio/Video Breakout Box (FG2254-10). This box facilitates the installation and distribution of video
(either Composite or S-Video), data (via Ethernet), and audio to Modero touch panels located up to 200
feet (60.96 m) from the breakout box. NXD-700Vi panels are ideally suited for displaying full motion
video and audio with overlay graphics for applications with demanding visual requirements.

NXD-700Vi Widescreen Video Touch Panel Kit

NXD-700Vi
(FG2258-04K)

The NXD-700Vi panel (FG2258-04) is shipped, by default with a Trim Ring containing
buttons, but the end user can later install the included Trim Ring without button
openings.

7" Widescreen Color Video Wall Mount Touch Panel Kit (with buttons)
(includes both an NXD panel and an NXA-AVB/ETHERNET A/V Breakout Box).

Key features common to both panels include:

 NXD-700Vi panels are based on the latest display technology and support AMX's 4th

generation (G4) graphics which provide higher brightness, richer colors, and deeper contrast.
The new G4 graphics technology is supported by the latest AMX TPDesign4 Touch Panel
Design program (version 2.6 or higher).

 NXD-700Vi panels display eye-catching images and full-motion video on a large 16:9 image

format, while providing a wide 100-degree top-to-bottom viewing angle.

 NXD-700Vi panels feature a front panel light sensor, motion sensor, IR receiver and a Sleep/

Setup Access combo button.

7" Modero Widescreen Touch Panels

1

Introduction

 NXD-700Vi panels support AMX Computer Control, which enables remote viewing and

control of any networked computer directly from the panel. This gives the user the ability to
launch digital music from a PC, cruise the Internet, check and respond to E-mail, open
software files, and launch applications. Anything you can do on your PC can be accomplished
through these panels.

 The wireless solution includes an NXA-WC80211GCF internal Wi-Fi card (FG2255-07) that

allows the NXD-700Vi to communicate with a NetLinx Master via a standard 802.11g
Wireless Access Point.

 NXD-700Vi panels feature programmable firmware that can be upgraded via either the

Ethernet port, wireless interface card, or the mini-USB port.

Trim ring - 60-2258-26Trim ring - 60-2258-25

Speaker

Microphone

Sleep button

Programmable pushbutton/LED

Programmable pushbutton/LED

FIG. 2 NXD-700Vi (front views)

Microphone

Sleep button

Speaker

2

7" Modero Widescreen Touch Panels

NXD-700Vi Specifications

The following table outlines the specifications for the 7" Widescreen Modero panels.

Specifications for 7" Widescreen Video Touch Panels

Dimensions (HWD): • NXA-RK7: metal rack-mount with black matte finish:

(4 RU - rack units high)

6.97" x 19.0" x 0.50" (17.70 cm x 48.26 cm x 1.27 cm)

• NXD-700Vi (with faceplate): 5.93" x 7.87" x 3.28"
(15.06 cm x 20.00 cm x 8.33 cm)

• CB-TP7 Conduit/Wallbox (optional): 5.47" x 7.23" x 3.40"
(13.90 cm x 18.40 cm x 8.64 cm)

Power Requirements
(stand-alone NXD-700Vi):

Memory (factory default): • 64 MB SDRAM

Weight (stand-alone): • NXD-700Vi: 4.12 lbs (1.87 kg)

Certifications: • FCC Part 15 Class B andCE

Panel LCD Parameters: • Aspect ratio: 16 x 9

Active Screen Area: • 6.00" x 3.60" (15.24cm x 9.14cm)

IR Reception Angle: • Horizontal: +

Supported Audio Sample
Rates:

• Constant current draw: 1.1 A @ 12 VDC (stand-alone)

• Startup current draw: 1.6 A @ 12 VDC (stand-alone)

• 128 MB Compact Flash (upgradeable to 1 GB - factory programmed)

• IEC60950

• Brightness (luminance): 350 cd/m

• Channel transparency: 8-bit Alpha blending

• Contrast ratio: 200:1

• Display colors: 256 thousand colors (18-bit color depth)

• Dot/pixel pitch: 0.19 mm

• Panel type: TFT Color Active-Matrix

• Screen resolution: 800 x 480 pixels (HV) @ 60 Hz frame frequency

• Video format: NTSC, PAL, and SECAM

• Viewing angles (100° total viewing angle):
Vertical: + 50° (up from center) and - 50° (down from center)

50° (left and right from center)

•Vertical: +

• 48000Hz, 44100Hz, 32000Hz, 24000Hz, 22050Hz, 16000Hz, 12000Hz,
11025Hz, and 8000Hz.

30° (up and down from center)

2

Introduction

7" Modero Widescreen Touch Panels

3

Introduction

Specifications for 7" Widescreen Video Touch Panels (Cont.)

Front Panel Components:

Light sensor: • Photosensitive light detector for automatic adjustment of the panel brightness

Motion sensor (PIR): • Proximity Infrared Detector to wake the panel when the panel is approached.

IR Receiver: • IR reception 38 KHz and 455 KHz IR frequencies.

Front setup access button: • Provides both access to the Setup and Calibration page and toggles the

Microphone: • Used for intercom applications

Speaker: • Single 2 watt speaker

LEDs • 2 blue LEDs (support On and Off)

Buttons • 2 programmable pushbuttons

Side Panel Components:

Mini-USB connector: • 5-pin Mini-USB connector used for programming, firmware update, and touch

Stereo Output connector: • Stereo output through a 3.5mm mini-jack (for use with external speakers or

Ethernet 10/100 port: • RJ-45 port for 10/100 Mbps communication. The Ethernet port automatically

Ethernet 10/100 LEDs: • LEDs show communication activity and connection information:

USB connector: • Type-A USB port can connect an external keyboard or mouse device for use

(a dim room results in a dimmer LCD display, and a bright room results in a
brighter LCD display).

Note: The light sensor can be adjusted via the Sensor Setup page (page 102).

• Activation range: +
from center).

Note: This sensor can be adjusted via the Sensor Setup page (see page 102).

• The IR receiver is located beneath the translucent Front Setup button. When
an IR code is detected it is sent to the NetLinx Master as a push on the
appropriate AMX IR channel.

• IR receivers and transmitters on G4 panels share the device address number
of the panel.

panel between a "sleep" or "wake" state.

- When wired, "sleep" status means the backlight is Off.

- When battery operated, wireless "sleep" status means the touch panel
base is either Off or "suspended".

(requires the NXA-AVB/ETHERNET Breakout Box for analog
communication)

- Both the LEDs and pushbuttons are only available when using the default
Button Trim Ring on the NXD panel.

panel file transfer between the PC and the target panel.

Note: When connecting the panel to PC using a CC-USB (or compatible)
cable, be sure to power the panel On before attempting to connect the USB
cable from the PC to the mini-USB port on the panel.

headphones).

negotiates the connection speed (10 Mbps or 100 Mbps), and whether to use
half duplex or full duplex mode.

• NXD-700Vi panels communicate with the NetLinx Master using the ICSP
protocol over Ethernet.

A-activity - Yellow LED lights when receiving or transmitting Ethernet data
packets.

L-link - Green LED lights when the Ethernet cables are connected and
terminated correctly.

with Virtual PC applications.

Note: External USB input devices (keyboard or mouse) must be plugged into
the rear/side USB connector before the unit is powered-up. The panel will not
detect these USB input devices until the unit cycles power.

45° (left and right from center) and + 20° (up and down

4

7" Modero Widescreen Touch Panels

Introduction

Specifications for 7" Widescreen Video Touch Panels (Cont.)

Side Panel Components
(Cont.):

Audio/Video connector: • RJ-45 connector for communication of differential audio/video signals

to/from the touch panel (panel type dependant). This connector receives
Composite video, Stereo (left/right) audio, and microphone audio.

• Video is received via the NXA-AVB/ETHERNET Breakout Box. Configuring
video windows for playback is done using TPDesign4.

• In-bound audio (from the breakout box) gets directed to the speakers.

• Out-bound audio is sent from the on-board microphone (on the
front-panel). Selecting audio files for playback is configured through
TPDesign4.

PWR connector: • 2-pin 3.5 mm mini-Phoenix connector.

Button Assignments: Button assignments can only be adjusted in TPD4 and not on the panels.

• Button channel range: 1 - 4000 button push and feedback (per address port)

• Button variable text range: 1 - 4000 (per address port)

• Button states range: 1 - 256 (General Button; 1 = Off State, 2 = On State)

• Level range: 1 - 600 (default level value 0-255, can be set up to 1-65535)

• Address port range: 1 - 100

Operating / Storage
Environment:

Included Accessories: • Installation Kit for 7" NXD panels (KA2258-02) includes:

Other AMX Equipment: •CB-TP7 (FG035-10)

• Operating Temperature: 0° C (32° F) to 40° C (104° F)

• Operating Humidity: 20% - 85% RH

• Storage Temperature: -20° C (-4° F) to 60° C (140° F)

• Storage Humidity: 5% - 85% RH

- 2-pin 3.5 mm mini-Phoenix connector (41-5025)

- Three Drywall clips (62-5924-05) and #6 - sheet metal screws

- Four Phillips-head screws (#4-40 x 0.250 Black)

• NXA-AVB/ETHERNET Breakout Box (FG2254-10): Provides video/audio
distribution to the A/V panel over CAT5 cable (up to 200’/60.96m) and
accepts either Composite or S-Video.

- Although the NXD-700Vi is only sold as part of a KIT configuration, the
breakout box can be purchased as a separate accessory.

• Trim Ring with button openings (60-2258-26)

• Trim Ring without button openings (60-2258-25)

- 7" metallic conduit box for Wall Mount installations.

• CC-USB (Type A) to Mini-B 5-Wire programming cable (FG10-5965)

•NXA-RK7 (FG2904-53)

- RackMount kit for 7" Wall Mount touch panels (NXD panels only).
Kit includes eight #10-32 screws and washers.

• NXA-WC80211GCF Wireless Upgrade Kit (FG2255-07)

- AMX 802.11G Compact Flash provides wireless Ethernet support

7" Modero Widescreen Touch Panels

5

Introduction

Specifications for 7" Widescreen Video Touch Panels (Cont.)

Other AMX Equipment
(Cont.):

• Upgrade Compact Flash (factory programmed with firmware):
NXA-700CF256M, 256 MB COMPACT FLASH CARD (FG2116-73)
NXA-700CF512M, 512 MB COMPACT FLASH CARD (FG2116-74)
NXA-700CF1G, 1 G COMPACT FLASH CARD (FG2116-75)

It is recommended that firmware KIT files only be transferred over a direct USB or
Ethernet connection and only when the panel is connected to a power supply. If
battery power or wireless connection fails during a firmware upgrade, the panel flash
file system may become corrupted.

NXD-700Vi Panels - Connector Layout

FIG. 3 shows the layout of the connectors (located on the rear of the base on the NXT and on the left side
panel of the NXD panels).

Ethernet (CAT5)

Keyboard/Mouse

Stereo Output

A L

Mini-USB

(Program)

PROGRAM

ETHERNET

10/100

NXD-700Vi - connectors located

on left side panel

FIG. 3 Connector layout on the NXD-700Vi touch panels

(USB)

KEYBOARD / PWR

MOUSE

AUDIO / VIDEO

Audio-Video from
NXA-AVB/ETHERNET (CAT5)

12VDC

Power

6

7" Modero Widescreen Touch Panels

NXA-AVB/ETHERNET Breakout Box

NXA-AVB/ETHERNET Breakout Box

The NXA-AVB/ETHERNET Breakout Box (FIG. 4) is included as part of the NXD-700Vi Kit
configuration (panel and box) but can be purchased as a separate accessory. This box facilitates the
installation and distribution of video, data, and audio to Modero touch panels located up to 200 feet
(60.96 m) from the AVB box. This unit accepts either Composite or S-Video from standard video
devices.

This breakout box can be mounted on either a horizontal flat surface or within an equipment rack
(by using an optional AC-RK Rack Kit).

Composite/

S-Video

(rear)

FIG. 4 NXA-AVB/ETHERNET Breakout Box (front and rear views)

Luma

Audio

In

Mic Out

S-Video Chroma

Power In

Ethernet In

Ethernet (to panel)

Power (to panel)

Audio/Video

(to panel)

(front)

7" Modero Widescreen Touch Panels

7

NXA-AVB/ETHERNET Breakout Box

Product Specifications

NXA-AVB/ETHERNET Specifications (FG2254-10)

Dimensions (HWD): • 1.50" x 5.55" x 4.88" (3.81 cm x 14.10 cm x 12.40 cm)

Power Consumption: • 50mA (with audio/video input)

Certifications: • FCC Part 15 Class B, CE, and EN60950

Features: • Accepts either Composite or S-Video (video-capable panels only)

Availabili ty : • This unit is included with CV5, CV7, CV10, NXD-700Vi, NXD-1000V,i and

Front Components: • 2-pin 3.5 mm Phoenix connector for power to the touch panel

Rear Components: • 6-pin 3.5 mm Phoenix connector for in-bound (left/right channel) audio

Included Accessories: • Two 2-pin Phoenix connectors (41-5025)

Other AMX Equipment: • AC-RK Accessory RackMount Kit (FG515)

• Width when attached to mounting ears: 6.65" (16.89 cm)

• 23mA (with no audio/video)

• Routed through NXA-AVB/Ethernet using a 12 VDC-compliant power supply

• Provides audio distribution to the non-video touch panels over a CAT5 cable
(up to 200 ft.)

• Provides video/audio distribution to the video-capable touch panels over
CAT5 cable up to 200 ft.(60.9 m)

1200V-Series Kit configurations

• Green LED provides an indication of power status

• RJ-45 connector provides Ethernet signals to the touch panel

• RJ-45 connector provides differential audio and video signals to the touch
panel (panel type dependant)

• 4-pin 3.5 mm Phoenix connector for out-bound (from microphone) audio

• BNC connector (female) for Composite or Chroma (for video-capable
panels only)

• BNC connector (female) for luminance (for video-capable panels only)

• RJ-45 connector for Ethernet input from the control system

• 2-pin 3.5 mm Phoenix connector for in-bound power

• 4-pin Phoenix connector (41-5047)

• 6-pin Phoenix connector (41-5063)

• Rack Mount Kit (KA2250-40) with mounting bracket (62-2254-02)

• Modero Table Top Cable (CA2250-50)

Installing the NXA-AVB/ETHERNET

A 12 VDC-compliant power supply can indirectly provide power to a Modero panel by routing power
through the NXA-AVB/ETHERNET Breakout Box. FIG. 5 shows a sample wiring configuration using
both an indirect or direct power connection for a video-capable Modero panel.

8

7" Modero Widescreen Touch Panels

NXA-AVB/ETHERNET Breakout Box

Indirect

Connect

12 VDC power

supply

Ethernet In

(RJ-45)

Video In

Mic Out

(4-pin captive-wire)

(BNC)

Audio In

(6-pin captive-wire)

Line Level out
(to amplifier
or VOL card)

(rear)

NXA-AVB/ETHERNET

Breakout Box

Power

supplied via

NXA-AVB box

12 VDC power

supply

Direct

Connect

Ethernet

(CAT5)

or

NXD/T Video-capable

Audio/Video
(CAT5)

(front)

Touch Panels

FIG. 5 Sample wiring configuration on video-capable panels using this breakout box

A 12 VDC-compliant power supply can also directly provide power through the unit to a target Modero
panel. FIG. 6 shows a sample wiring configuration for a non-video capable Modero panel.

Direct

connect

12 VDC power

supply

Ethernet
(CAT5)

Audio (CAT5)
between the
NXA-AVB/ETHERNET
Breakout Box

NXD/T Non-video capable

Touch Panels

FIG. 6 Sample wiring configuration using non-video capable Modero panels

The breakout box unit can be mounted on either a horizontal flat surface or into an
equipment rack (by removing the front screws and attaching it to an optional AC-RK).
The power supply being used on the NXA-AVB/ETHERNET is dependant on the
power requirements of the target touch panel.

Use a standard CAT5 Ethernet cable to provide both communication and 10/100 network connectivity
between the panel, NXA-AVB/ETHERNET, NetLinx Master, and the network.

Wiring the NXA-AVB/ETHERNET connectors and cables

The inputs and outputs on the breakout box are separated into front and rear connectors. The rear
connectors are used to input external signals. The front connectors are used to communicate signals
between the NXA-AVB/ETHERNET and a target Modero panel. FIG. 7 provides a layout of the wiring
connection both into and from the breakout box.

7" Modero Widescreen Touch Panels

9

NXA-AVB/ETHERNET Breakout Box

Audio In - Left Channel

(6-pin captive wire)

Audio In - Right Channel

(6-pin captive wire)

GND

In (-)

In (+)

GND
In (-)

In (+)

F
R
O
N
T

NXA-AVB/ETHERNET

Breakout Box

Microphone Out

(4-pin captive wire)

GND(-)
Out (-)

Out (+)

Comp/Y (BNC)

C (BNC)

Ethernet

(RJ-45)

R
E

12 VDC power

supply

A
R

FIG. 7 NXA-AVB/ETHERNET Breakout Box connector wiring diagram

The rear-panel wiring connections are described below (from left to right):

• AUDIO IN: 6-pin mini-Phoenix connector, divided into left and right audio channels. Each
channel is divided into GND, IN+, and IN- terminal cable connectors
(2 sets of 3 for each channel).

An example of this cable is to strip the ends of 2 RCA audio cables and insert
them into their respective locations on the Audio In port.

Either a balanced (+, -, and GND) or unbalanced (+ and GND) audio
signal can be connected to this input.

• MIC OUT: 4-pin mini-Phoenix connector, divided into GND, OUT-, and OUT+ terminal

• Video In BNCs: Feeds either Composite/S-Video Luma or S-Video Chroma signals into the

• ETHERNET: RJ-45 connector routes data to the G4 touch panel through the front Ethernet

•PWR: 2-pin mini-Phoenix connector that connects to a 12 VDC-compliant power

connectors.

An example of this cable is to strip the terminal ends of a 3.5mm mini-jack and
insert them into their respective locations on the Mic Out port. This signal can
be fed as a Line Level In to either an amplifier or an AMX VOL card.

Either a balanced (+, -, and GND) or unbalanced (+ and GND) audio signal
can be connected to this output.

NXA-AVB/ETHERNET. This feed is then redirected out to a Modero panel
through the front Audio/Video CAT5 port.

port. These connections use a standard CAT5 Ethernet cable to provide
communication between the target touch panel, breakout box, and NetLinx
Master.

supply. This port can be used to provide power to a Modero panel by sending it
through the NXA-AVB/ETHERNET (rear power connector through to the front
power connector).

Audio/Video

(CAT5)

Ethernet Out

(CAT5)

Power to
touch panel

10

7" Modero Widescreen Touch Panels

NXA-AVB/ETHERNET Breakout Box

Wiring the NXA-AVB/ETHERNET for Unbalanced Audio

Most domestic audio equipment has unbalanced audio inputs and outputs. This means that the audio
output (left, right, or mono) appears on a single wire, and is referenced to "0 V" or "Ground". Typical
connectors used are RCA "phono" connectors, DIN plugs/sockets, and 0.25" (6.3mm) or 3.5mm jack
plugs/sockets.

Unbalanced audio is adequate for most domestic environments and for line-level signals in a typical
broadcast studio. Problems may occur if the signals are carried over long distances, especially if the
source and destination have separate main supplies. Use the following wiring drawing (FIG. 8) to
configure an unbalanced audio connection.

GND

IN-

IN+

GND

IN-

IN+

AUDIO IN

MIC OUT

GND

OUT-

OUT+

FIG. 8 Wiring the rear AUDIO IN and MIC OUT for use with Unbalanced Audio

Left Channel

Right Channel

Microphone

Unbalanced IN
(Jumper IN- to GND)

Unbalanced IN
(Jumper IN- to GND)

Unbalanced OUT

When using unbalanced audio for the AUDIO IN connector (FIG. 8), the "-" and the "GND" terminals
should be connected together and then connected to the GND of the unbalance audio signal. When
connecting to an unbalanced audio input from the MIC OUT connector (FIG. 8), wire the "+" terminal to
the signal input, and the "GND" terminal to the signal ground.

Wiring the NXA-AVB/ETHERNET for Balanced Audio

Professional audio equipment will often use balanced audio inputs and outputs, usually on 3-pin "XLR"
connectors. A balanced audio signal consists of a pair of wires carrying the audio signal in anti-phase
with each other (if one wire carries a positive voltage, the other carries an equal and opposite negative
voltage).

The advantage of balanced audio over unbalanced audio is its ability to reject external interference added
as the signal is carried over the wire. The receiving equipment takes the voltage difference between the
two wires as the input signal. Interference will usually get added to both wires equally, and so gets
cancelled by the receiving equipment.

The 3 wires used in a typical XLR lead are often referred to as Ground, Live (Hot) and Return (Cold).
"Live" and "Return" carry the "in-phase" and "out-of-phase" versions of the audio respectively. The pins
of the XLR plug/socket are as follows:

• X = Ground

• L = Live (Hot)

• R = Return (Cold)

7" Modero Widescreen Touch Panels

11

NXA-AVB/ETHERNET Breakout Box

When connecting the MIC OUT connector to a balanced audio input (FIG. 9), use all three audio
terminals (+, -, and GND), then connect the "+" terminal to the "live" signal, the "-" terminal to the
"return" signal, and the "GND" terminal to the ground signal.

GND

OUT-

OUT+

FIG. 9

Wiring the rear MIC OUT connector for use with Balanced Audio

Ground signal

Return signal

Line signal

Balanced OUT

12

7" Modero Widescreen Touch Panels

NXD-700Vi Touch Panel Accessories

NXD-700Vi Touch Panel Accessories

The following section outlines and describes the other AMX equipment available for these touch panels.

NXA-WC80211B/CF 802.11b Wireless Card (FG2255-03)

These touch panels can connect to a wireless network using an optional AMX 802.11b Wireless
Interface Card shown in FIG. 1. This internal card is field-upgradeable within both models of panels.

FIG. 1 NXA-WC80211B/CF Wireless Interface Card (WIC)

This unit is certified and available for use in the United States (FCC), Canada (IC),
Europe (CE) and Japan (TELEC).

The NXA-WC80211B/CF Wireless Interface Card works with compatible 802.11b Wireless Access
Points such as the NXA-WAP200G. Please follow your particular Wireless Access Point’s instruction
manual for the correct procedures to setup either a secured or unsecured connection. The following table
lists the specifications for the wireless interface card.

802.11b Wireless Interface Card Specifications

Dimensions (HWD): • 2.07" x 1.68" x 0.21" (52.56 mm x 42.80 mm x 5.57 mm)

Weight: • 13.61 grams (0.030 lbs)

Description: • 2.4 GHz Direct Sequence Spread Spectrum (DSSS) 802.11b 11M wireless PC

Features: • Wired Equivalent Privacy (WEP) 64-bit and 128-bit data encryption

Antenna: • 2, Ceramic (Diversity Supported)

Certifications: • FCC (United States)

Host Interface: • Compact Flash Type I

Interoperability: • Interoperable with Wi-Fi (WECA) certified products

LED Indicators: • Power / Link activity

Modulation: • DSSS, DBSK, DQSK, CCK

Network Standard: • IEEE 802.11b

Number of Channels: •14

Operating Voltage: • 5 / 3.3 V

card with detachable Antenna.

• Diversity Antenna Connectors automatically select the best available signal

• Supports infrastructure (communications to wired networks via Access Points),
and roaming (standard IEEE 802.11b compliant)

• IC (Canada)

• CE (Europe)

• TELEC (Japan)

7" Modero Widescreen Touch Panels

1

NXD-700Vi Touch Panel Accessories

802.11b Wireless Interface Card Specifications (Cont.)

Operating Channels: • 11 Channels (USA, Canada)

Operating Environment: • Temperature: 0°C ~ 70°C (non-operating) and -15 ~ 80°C (storage)

Power Consumption: • TX power consumption: <

Radio Data Rate: • 1Mbps, 2Mbps, 5.5Mbps, 11Mbps, Auto Rate

Receive Sensitivity: •@PER < 8%

RF Output Power: • 15 dBm +/- 1 dBm

Security: • WEP 64,128 bit, WPA/TKIP

Wireless Restrictions: • In R&TTE countries, such as France, the 802.11g frequency band is restricted to

• 13 Channels (Europe)

• 14 Channels (Japan)

• 4 Channels (France)

• Humidity (non-condensing): 5% ~ 95% RH

265 mA

• RX power consumption: <

• Sleep Mode: 2 mA - 15 mA

11 Mbps: -83 dBm (max)

5.5 Mbps: -86 dBm (max)
2 Mbps: -89 dBm (max)
1 Mbps: -92 dBm (max)

• Channels 1 - 11 (North America)

2454 - 2483.5 MHz (2.4 - 2.4835 GHz) and a max power output of
100 mW EIRP outdoor.

165 mA

It is recommended that any upgrade of internal equipment be done simultaneously in
order to reduce the risk of damage to internal components.

NXA-WC80211GCF 802.11g Wireless Card (FG2255-07)

These panels can also connect to a wireless network using the (optional) 802.11g Wi-Fi CF card. This
internal WIC (FIG. 2) can be purchased separately as a Wi-Fi upgrade kit from AMX.

PIFA antenna
with metal plate

FIG. 2 NXA-WC80211GCF 802.11g wireless card

This interface card (FG2255-07) is a 2.4 GHz Wi-Fi LAN CF Card which upgrades a Modero panel’s
wireless RF capabilities from 802.11b to 802.11g. This card also provides the end-user with several new
methods of wireless encryption and data security such as WPA and WPA2. In addition to being
backwards compatible with 802.11b networks, this card is installable within all current MVP,
NXD-700Vi, NXD-10000Vi, CV7, and CV10 panels. To fully utilize these newer wireless security
features, this card must be used in tandem with the latest Modero firmware upgrade available at
www.amx.com.

2

7" Modero Widescreen Touch Panels

NXD-700Vi Touch Panel Accessories

This card works with compatible 802.11b/g Wireless Access Points such as the NXA-WAP200G (which
uses a default SSID of AMX). Please follow your particular Wireless Access Point’s instruction manual

for the correct procedures to setup either a secured or unsecured connection. The following table lists the
specifications for the NXA-WC80211GCF.

This upgrade kit requires that pre-existing panels first be removed from their current location (surface,
wall or docking station) before an installer can access the internal circuit boards and upgrade a
pre-existing 802.11b wireless CF card.

Only MVP panels require the use of a cardboard cutout (Mounting Template) to properly position the
metal antenna plate onto the inner surface of the unit’s rear plastic housing

NXD-700Vi, NXD-1000Vi, CV7, and CV10 panels only require locating the Compact Flash’s metal
cover plate on the main circuit board and then adhering the terminal antenna connector to that location
using the included double-sided adhesive tape.

If the CF metal cover plate is not present over the wireless card slot on a NXD-700Vi,
NXD-1000Vi, CV7, or CV10 panel, you can use the adhesive tape to secure the
terminal antenna to the surface of the new card (atop the product label).

The procedures for upgrading a CF card on an MVP is identical for both MVP-7500 and MVP-8400
panels. The procedures for upgrading/installing the new CF card are also similar across all referenced
NXT panels and NXD panels as a group (differences arise from their housing).

NXA-WC80211GCF Specifications

Dimensions (HWD): • 0.22" x 1.68" x 2.40" (5.6 mm x 42.80 mm x 61.0 mm)

Weight: • 19.50 grams (0.043 lbs)

Description: • Wireless LAN Compact Flash Card with external PIFA antenna.

• Features enterprise-class security such as WPA and WPA2 security.

Features: • Compact Flash Type I form factor

• Enhanced range and throughput

• Features wireless security such as: WPA, WPA2 and WEP

• Field-installable

• Incorporates DSSS and OFDM radio technology

• Operates at ISM frequency bands of 2.4 GHz, while providing data transfer
speeds of up to 54Mbps.

• Support for IEEE 802.11b and 802.11g

• Supports Advanced Encryption Standard (AES) 64-bit and 128-bit data
encryption, along with an Re4 encryption cipher (64/128-bit)

• Supports authentication methods such as: EAP-FAST, EAP-LEAP, EAP-PEAP,
EAP-TLS, and EAP-TTLS

• Supports Wired Equivalent Privacy (WEP) 64-bit and 128-bit data encryption
(known to the on-board firmware as Static WEP)

Antenna Type: • External PIFA antenna (factory-installed)

Bus Interface: • Compact Flash Type I

Certifications: • FCC Part 15 Class B, CE, IC, TELEC, and Wi-Fi

Media Access Control
Techniques:

• Using 802.11b DSSS communication:
DBPSK @ 1 Mbps
DQPSK @ 2 Mbps
CCK @ 5.5 Mbps

• Using 802.11g OFDM communication:
BPSK @ 6 and 9 Mbps
QPSK @ 12 and 18 Mbps
16-QAM @ 24 and 36 Mbps
64-QAM @ 48 and 54 Mbps

7" Modero Widescreen Touch Panels

3

NXD-700Vi Touch Panel Accessories

NXA-WC80211GCF Specifications (Cont.)

Network Architecture: • Infrastructure mode (Client-to-Access Point)

Operating Channels: • Using 802.11b & g communication:

Operating Environment: • Temperature: 0°C ~ 45°C (32°F to 113°F) (operating) and

Operating Voltage: • 3.3V + 5% I/O supply voltage

Power Consumption: • @ 802.11b communication:

Radio Data Rate: • 802.11g compliant: 1, 2, 5.5, 11 (DSSS/CCK); 6, 9, 12, 18, 24, 36, 48, and 54

Radio Technology: • Using 802.11b communication: DSSS (Direct Sequence Spread Spectrum)/CCK

Receiver Sensitivity: • Using 802.11b communication @ FER<8%:

RF Frequency Ranges: • Using 802.11b & g communication:

Standard Conformance: • IEEE 802.11b

- 04: (Ch 10 - 13) - France

- 11: (Ch 1 - 11) - North America

- 13: (Ch 1 - 13) - Europe ETSI

- 13: (Ch 1 - 13) - Japan (802.11g)

- 14: (Ch 1 - 14) - Japan (802.11b)

Note: To alter the card’s default country code (North America), please
contact an AMX Technical Support representative for detailed procedures
and information.

-20°C ~ 70°C (-4°F to 158°F) (storage)

• Humidity: (non-condensing) 5% ~ 90% RH (operating) and
(non-condensing) 5% ~ 95% RH (storage)

- RX: 270 mA

- TX: 435 mA

- Standby: 240 mA

• @ 802.11g communication:

- RX: 270 mA

- TX: 460 mA

- Standby: 240 mA

(OFDM) Mbps data rates

(Complementary Code Keying)

• Using 802.11g communication: DSSS/CCK, OFDM (Orthogonal Frequency
Division Multiplexing

1 Mbps: -94 dBm (max)
2 Mbps: -93 dBm (max)

5.5 Mbps: -92 dBm (max)
11 Mbps: -90 dBm (max)

• Using 802.11g communication @ PER <10%:
6 Mbps: -87 dBm (max)
9 Mbps: -86 dBm (max)
12 Mbps: -86 dBm (max)
18 Mbps: -84 dBm (max)
24 Mbps: -82 dBm (max)
36 Mbps: -78 dBm (max)
48 Mbps: -74 dBm (max)
54 Mbps: -72 dBm (max)

Europe ETSI: 2.412 ~ 2.472 GHz
France: 2.457 ~ 2.472 GHz
Japan (802.11b): 2.412 ~ 2.484 GHz
Japan (802.11g): 2.412 ~ 2.472 GHz
North America: 2.412 ~ 2.462 GHz

• IEEE 802.11g

• IEEE 802.11e

• IEEE 802.11i

• Wi-Fi (WPA and WPA2)

4

7" Modero Widescreen Touch Panels

NXD-700Vi Touch Panel Accessories

NXA-WC80211GCF Specifications (Cont.)

Transmit Output Power: • 802.11b communication: 12 +-1 dBm (1, 2, 5.5, 11 Mbps)

• 802.11g communication: 12 +-1 dBm (6, 9, 12, 18, 24, 36, 48, and 54 Mbps)

Wireless LAN Security: • EAP-FAST

• EAP-LEAP

•EAP-PEAP

•EAP-TLS

•EAP-TTLS

• WEP 64 & 128

•WPA-PSK

Touch Panel
Compatibility:

Included Accessories: • Double-sided adhesive tape

Other AMX Equipment: • NXA-WAP250G Modero Wireless Access Point (FG2255-50)

• MVP-7500 (FG5965-01)

• MVP-8400 (FG5965-02)

• NXD-700Vi (FG2258-04)

• NXD-1000Vi (FGXXXXX)

• NXD-CV10 (FG2259-02)

• NXT-CV10 (FG2259-01/03)

• NXD-CV7 (FG2258-02)

• NXT-CV7 (FG2258-01)

• Mounting Template cutout (62-2255-04)

• NXA-WC80211GCF Installation Guide

• Two Alcohol cleaning pads

• Wireless CF card with wireless antenna

• Upgrade Compact Flash memory (factory programmed with firmware):
NXA-CFSP128M - 128 MB compact flash card (FG2116-36)
NXA-CFSP256M - 256 MB compact flash card (FG2116-37)
NXA-CFSP512M - 512 MB compact flash card (FG2116-38)
NXA-CFSP1GB - 1 GB compact flash card (FG2116-39)

7" Modero Widescreen Touch Panels

5

NXD-700Vi Touch Panel Accessories

6

7" Modero Widescreen Touch Panels

NXA-CFSP Compact Flash (FG2116-7x)

NXA-CFSP Compact Flash (FG2116-7x)

Every NXD-700Vi Modero panel is shipped with a 128 MB Compact Flash card (NXA-CFSP).

If possible, upgrade the panel’s internal components (Compact Flash or wireless
interface cards) prior to installing or using the panel.

The NXA-CFSP Compact Flash card is factory programmed with specific panel firmware and can be
upgraded to several sizes, up to 1GB:

Optional Compact Flash Upgrades

• NXA-700CF256M, 256 MB COMPACT FLASH CARD (FG2116-73)

• NXA-700CF512M, 512 MB COMPACT FLASH CARD (FG2116-74)

• NXA-700CF1G, 1 G COMPACT FLASH CARD (FG2116-75)

Upgrading the Compact Flash card in both panel types involves opening the panel enclosure/outer
housing to access the internal circuit board, removing the existing card, replacing it, and then resecuring
the panel enclosure, as described in the following section.

7" Modero Widescreen Touch Panels

7

NXA-CFSP Compact Flash (FG2116-7x)

8

7" Modero Widescreen Touch Panels