Page 1
AMX LIMITED WARRANTY AND DISCLAIMER:
AMX Corporation warrants this product to be free of defects in material and workmanship
under normal use for three (3) years from the date of purchase from AMX Corporation,
with the following exceptions:
Electroluminescent and LCD Control Panels are warranted for three (3) years, except for
the display and touch overlay components that are warranted for a period of one (1) year.
Disk drive mechanisms, pan/tilt heads, power supplies, MX Series products, and KC Series
products are warranted for a period of one (1) year.
AMX Lighting products are guaranteed to switch on and off any load that is properly
connected to our lighting products, as long as the AMX Lighting products are under
warranty. AMX Corporation does guarantee the control of dimmable loads that are properly
connected to our lighting products. The dimming performance or quality cannot be
guaranteed due to the random combinations of dimmers, lamps and ballasts or transformers.
Unless otherwise specified, OEM and custom products are warranted for a period of one
(1) year.
AMX software is warranted for a period of ninety (90) days.
Batteries and incandescent lamps are not covered under the warranty.
This warranty extends only to products purchased directly from AMX Corporation or an
Authorized AMX Dealer.
AMX Corporation is not liable for any damages caused by its products or the failure of its
products to perform. This includes any lost profits, lost savings, incidental damages, or
consequential damages. AMX Corporation is not liable for any claim made by a third party
or by an AMX Dealer for a third party.
All products returned to AMX require a Return Material Authorization (RMA) number. The
RMA number is obtained from the AMX RMA Department. The RMA number must be
clearly marked on the outside of each box. The RMA is valid for a 30-day period. After the
30-day period the RMA will be cancelled. Any shipments received not consistent with the
RMA, or after the RMA is cancelled, will be refused. AMX is not responsible for products
returned without a valid RMA number.
This limitation of liability applies whether damages are sought, or a cliam is made, under
this warranty or as a tort claim (including negligence and strict product liability), a contract
claim, or any other claim. This limitation of liability cannot be waived or ammended by any
person. This limitation of liability will be effective even if AMX Corporation or an authorized
representative of AMX Corporation has been advised of the possibility of any such damages.
This limitation of liability, however, will not apply to claims for personal injury.
Some states do not allow a limitation of how long an implied warranty lasts. Some states
do not allow the limitation or exclusion of incidental or consequential damages for consumer
products. In such states, the limitation of the Limited Warranty may not apply. This Limited
Warranty gives the owner specific legal rights. The owner may also have other rights that
vary from state to state. The owner is advised to consult applicable state laws for full
determination of rights.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES
NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX
CORPORATION EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED
WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED
TO THE TERMS OF THIS LIMITED WARRANTY.
installation manual
NXA-TSJ45
NXA-MPS16F
Page 2
GENERAL overview:
NXA-TSJ45 informations:
4100-411
• Read and understand all instructions before installation
• Never install products during a lightning storm
• These products are intended for indoor use only
• Protection devices are intended for use as secondary surge protection at the
equipment level behind a primary building protector designed for lightning effects
protection.
• Always keep cord lengths between equipment and protector to a minimum, try not
to exceed 10 inches
• Ground wires must be attached directly to metal chassis of equipment to be protected
• Verify that metal equipment chassis are connected to earth ground via properly
grounded AC outlet
• Protectors reset after each surge. In the unlikely event of a catastrophic surge, the
protector will self sacrifice and not allow damaging surges to reach your equipment
• Confirm power off to the equipment being protected
• Disconnect incoming data
• Connect the small cable to the end closest to the ground wire
• Attach the green gound wire to the metal chassis
• Attach the incoming wire to other suppressor opening
• Apply power
NXA-MPS16F information:
• Remove power to unprotected equipment
• Install the 19" rack mount unit to the rack
• Verify rack grounding
• Port 1 - Ethernet; all others are NetLinx
• Disconnect incoming data line from equipment and connect to "in" port on the rack unit
• Connect cable to corresponding "out" port and reconnect to equipment
• Apply power to equipment
Loading...