Page 1
DATA SHEET
N2300 Series N2322 4K Decoder
NMX-DEC-N2322 (FGN2322-SA), Stand Alone
Overview
The NMX-ENC-N2312 Encoder and NMX-DEC-N2322 Decoder provide a flexible,
feature-rich, and simple-to-deploy Digital Media Distribution and Switching
solution which can be used in 4K applications with resolutions up to 4096x2160,
with support for HDCP 2.2. This motion-based wavelet codec solution delivers video
with nearly imperceptible latency at an incredibly low 200 Mb/s bandwidth
allowing 4K distribution over standard gigabit Ethernet networks.
Any source can be sent to one or more displays by routing through layer 2 / layer 3
switches utilizing standard Cat5e cable. The NMX-DEC-N2322 includes standard
features like output scaling, bi-directional serial, IR, embedded 7.1 audio, and KVMover-IP extension.
Features
Design Flexibility – Start as small as 1x1 and grow the system in increments of single sources and
devices by simply adding additional encoders and decoders.
Power Over Ethernet (POE) – eliminates requirement for local power supply and speeds
installation. Units can still be powered locally from 12VDC allowing for easy rack-mountable, highdensity installations
Infrared (IR) – Emitter connection allows control of IR-only display devices
Fast Install – With Phoenix connectors for Power, IR, RS232 serial, and analog audio interfaces
Balanced and Unbalanced Audio – Embedded 7.1 digital audio or balanced/unbalanced analog audio
Multiple Connection Options – RJ-45 and SFP network connectors and HDMI video connections
KVM –Dual USB-A control for KVM applications
Native NetLinx – NetLinx Studio can easily recognize the device
© 2016 AMX. All rights reserved.
Page 2
Specifications
VIDEO
Video Input
Network video over Ethernet via RJ45 port or fiber via
1G SFP port
Video Output
HDMI 2.0, DVI-D (through adapter)
Formats
HDMI 2.0, DVI-D (through adapter), HDCP 2.2 content
protection support
Video Codec
Motion-based wavelet technology
Input Resolutions
Supports most common resolutions from HD up to
4096x2160
See the instruction manual for the NMX-ENC-N2312
Encoder for all supported resolutions
Output Resolutions
720p, 1080p, 4K30 or input resolution if scaler is
disabled
Output Scaling
Note: there are no limitations when upscaling to 720p,
1080p, 4K30.
A 4K30 signal can be downscaled to 1080p without
issue. Scaling down to 720p from either 4K30 or
1080p is not supported in the product.
Color Space
4:2:0 4K30 4:2:2 – HD
LocalPlay/HostPlay
8 playlists
HostPlay
1 image/list
Note
Jumbo Frames Required
Video Wall Construction
Supported within the NMX-DEC-N2322, the N2300
Series is not compatible with SVSI Windowing
Processors at this time
Network Video Recording
Not compatible with SVSI NVR at this time
AUDIO – SIGNAL TYPES
Input
Network audio over Ethernet via RJ45
Output
Embedded audio on DVI-D or HDMI (through adapter),
analog audio output
KEYBOARD AND MOUSE
Keyboard & Mouse
Connect the Decoder to the keyboard and mouse, and
an N2300 Series Encoder to the PC being controlled
AUDIO - FORMATS
Input Signal Types
Network audio over Ethernet via RJ45
Output Signal Types
Embedded audio on HDMI or DVI-D (through adapter)
HDMI Audio Formats
8ch PCM
Analog Audio Format
Stereo 2-channel
Audio Breakaway
Supported
LATENCY
Latency
17-ms at 60fps for 1920x1080 and lower resolutions
34-ms at 30 fps for 4K30 4K resolutions
NOTE: This is the combined encode plus decode
latency. Total latency from source to screen will also
include any network latency and screen latency.
Scaling adds one frame of latency (17ms at 60fps).
NMX-DEC-N2322 | 2
Page 3
Switching
Up to 1.5s delay, not seamless
COMMUNICATIONS
Ethernet
P0
10/100/1000 Mbps, auto-negotiating, auto-sensing,
full/half duplex, DHCP, Auto IP, and Static IP
P1
1 Gbps SFP port which accepts compatible fiber
transceivers or direct attach cables (fiber or copper
cabling)
HDMI
HDCP, EDID management
PORTS
+12V 2A
One 12 Volt DC power input
P0
8-wire RJ45 female
10/100/1000 Mbps 10/100/1000Base-T auto-sensing
gigabit Ethernet switch port
Provides network connection, network AV video, and
power to the Encoders and Decoders (PoE power)
P1
1-Gbps SFP+ port (SFP+ fiber transceiver or direct
attach cable not included)
Provides network connection and networked AV video
IR OUT
2-pin terminal Phoenix connector. Provides Infrared
(IR) output only (33-60 kHz; typically 39 kHz). Emitter
may be necessary (not included).
RS232
3-pin terminal Phoenix connector which provides a
serial control interface. Full duplex communication.
Available terminal speed settings: 9600-115200 baud
rate.
AUDIO
5-pin terminal Phoenix connector which provides userselectable balanced/unbalanced output.
HDMI OUT
HDMI video output
CONTROLS AND INDICATORS – FRONT PANEL
RESET Button
Recessed pushbutton
Press to initiate a 'warm restart' causing the processor
to reset, but not lose power
A reset does NOT affect the current settings
ID Button
Recessed pushbutton
Press to send a notification out on the network to
identify the unit (the notification causes a pop-up
dialog in N-Able and N-Command)
POWER LED
On solid (green) when operating power is supplied (via
PoE or local power supply)
This activity is also shown by the PWR LED on the rear
panel
STATUS LED
On flashing (green) when there is software activity
This activity is also shown by the STAT LED on the rear
panel
CONTROLS AND INDICATORS – REAR PANEL
PWR LED
Same as POWER LED described above
HDMI LED
On (green) when there is a connection to a valid
display
NMX-DEC-N2322 | 3
Page 4
STAT LED
Same as STATUS LED described above
STRM LED
On (green) when the unit is receiving video
POWER SUPPLY
Power Supply, External, Optional
2.0 Amp @ 12 Volts DC; 100-240 Volts AC power
supply; optional NMX-ACC-N9312 (FGN9312)
Power over Ethernet (PoE), External, Optional
Can be powered via a PoE switch or other equipment
with a PoE source
Conforms to IEEE 802.3af Class 3 (802.3at Type 1)
NOTE: In order for the unit to receive Power over
Ethernet (PoE), it must be connected to a switch or
other equipment that has a PoE PSE (Power Sourcing
Equipment) port.
Warning: Do not run wiring that is connected to a PoE
PSE port outside of the building where the PSE resides.
It is for intra-building use only.
ENVIRONMENTAL
Temperature
32° to 104°F (0° to 40°C)
Humidity
10% to 90% RH (non-condensing)
Heat Dissipation
Up to ~44 BTU/hr
GENERAL
Dimensions (HWD)
1.05” x 7.888” x 5.5” (2.67 cm x 20.04 cm x 13.8 cm)
Weight
1.6 lbs (0.66 kg)
Mounting Options
Stand alone, surface mount, wall mount, or rack
mount
Surface and wall mounting requires (not included):
•NMX-ACC-N9101 (FGN9101), Mounting Wings for
SVSI N-Series Encoders and Decoders
Rack mounting requires (not included):
•NMX-ACC-N9102 (FGN9102), 1RU Rack Shelf for Two
Side-by-Side for SVSI N-Series Encoders and Decoders
Regulatory Compliance
FCC, CE, and NTRL
Recommended Accessories
•NMX-ACC-N9312 (FGN9312), Power Supply 12V
External
•NMX-ACC-N9382 (FGN9382), 1RU Power Supply 16Channel 12V for up to 16 SVSI N-Series Encoders and
Decoders
•NMX-ACC-N9101 (FGN9101), Mounting Wings for
SVSI N-Series Encoders and Decoders
•NMX-ACC-N9102 (FGN9102), 1RU Rack Shelf for Two
Side-by-Side SVSI N-Series Encoders and Decoders
About AMX by HARMAN
Founded in 1982 and acquired by HARMAN in 2014, AMX® is dedicated to providing AV solutions for an IT World. AMX solves the complexity of
managing technology with reliable, consistent and scalable systems comprising control, video switching and distribution, digital signage and technology
management. AMX systems are deployed worldwide in conference rooms, classrooms, network operation/command centers, homes, hotels,
entertainment venues and broadcast facilities, among others. AMX is part of the HARMAN Professional Group, the only total audio, video, lighting, and
control vendor in the professional AV market. HARMAN designs, manufactures and markets premier audio, video, infotainment and integrated control
solutions for the automotive, consumer and professional markets. Revised 10.2.16. ©2016 Harman. All rights reserved. Specifications subject to change.
www.amx.com | +1.469.624.7400 |800.222.0193
NMX-DEC-N2322 | 4
Loading...