AMX HPX-P200-PC-US Quick Start Guide

QUICK START GUIDE

Last Revised:2/18/2016

93-0561-01 REV: C

Interlocking tab

Cables

HPX Base Assembly

Mounting Surface

End Cap

HPX-P200-PC-US HydraPort Power Outlet (US) Module with Cord

Overview

The HPX-P200-PC-US AC Power Module (FG561-01) is designed to be used exclusively
in the AMX HPX-600/900/1200/1800 or HydraPort

The HPX-P200-PC-US module provides power connectivity for US plug types to the
HydraPort chassis.

FIG. 1

HPX-P200-PC-US AC POWER MO DULE

The HPX-600/900/1200/1800 and HydraPort Touch (HPX-MSP-7/10) units are
designed to be mounted in a horizontal surface such as a conference room table or
lect ern.

Refer to the installation guide for the HPX-600/900/1200/1800 for further
instructions.

ATTENTION: Only a professional, AMX-qualified instal ler should pe rform this inst alla ti on.
Installation must conform to all local codes. This product may not be installed by the
end-user. Disconnect all AC Power Cords from the AC Mains Power Branch Circuit until
installation is complete.

®

Touch Chassis (HPX-MSP-7/10).

Product Specif ications

HPX-P200-PC-US AC

Dimensions (HWD): 50mm x 66mm x 70mm (2.0" x 2.6" x 2.8")

Module Spaces 2

Table Cu tout Dimensions: See HPX-600/900/1200/1800

Weigh t: 0.5 Kg (1 l bs)

Enclosure • Black Polycarbonate material.

Rear Connections 2,430mm (8ft) 14 AWG x 3 Conductor

Compatibility • HPX-600

• Fire Rated to 5VA

Power Cord with a NEMA 5-15 US
3 Pin AC Mains Power Plug

•HPX-900

•HPX-1200

•HPX-1800

Installation

Too l s R e q ui r e d

• #2 Phillips Screwdriver

Step 1: Remove the HPX-600/900/1200/1800 (if required)

Remove the HPX-600/900/1200/1800 or HydraPort Touch (HPX-MSP-7/10) from the
mounting surface if it has previously been installed in a mounting surface.

Note: Refer to the Installation guide for instructions on installation and removal of the
HPX-600/900/1200/1800.

Step 2: Install the HPX-P200-PC-US AC Power Module

1. Remove one of the plastic end caps from the HPX-600/900/1200/1800:
a. Remove the silver #6 screw retaining the pawl and door
b. Remove the 6 #6 black sheet metal screws retaining the plastic end cap to

the metal frame

c. Slip the plastic end cap off the metal frame

2. Remove existing modules or blanks to make space for the HPX-P200-PC-US AC
Power Module.

3. Insert the HPX-P200-PC-US AC Power Module into the metal frame by sliding it
into the slots provided in the metal frame.

Note the orientation o f the interlocking tabs. The interlocking tabs on each
module should all be facing towards the same end of the chassis (FIG. 2).

FIG. 2 INS TAL LING THE HPX-P200 -PC -US MO DULE

4. Replace the plastic end cap by replacing the 6 # 6 sheet metal screws and the #6
screw retaining the pawl and door.

Note: Do not over-tighten the pivot pawl screw (do not use a high-powered drill on
this screw).

5. Use cable ties and one or more of the sliding clips to secure the cable to the HPX
Base Assembly.

Step 3: Replace the HPX-600/900/1200/1800

Reinstall the HPX-600/900/1200/1800 or HydraPort Touch (HPX-MSP-7/10) by
reversing Step 1.

Note: Refer to the Installation guide for the HPX-600/900/1200/1800 as required.

Step 4: Plug the HPX-P200-PC-US into the Branch Circuit

Plug the attached power cord’s NEMA 5-15 Plug into the AC Mains Power Branch
Circuit.

Note: The AC Mains Power Outlet should be within sight of the installed HPX-P200-PC-US
and HPX-600/900/1200/1800.

© 2016 Harman. All rights reserved. HydraPort, AMX, AV FOR AN IT WORLD, and HARMAN, and their respective logos are registered trademarks
of HARMAN. Oracle, Java and any o ther company or brand name referenced may be trademarks/registered trademarks of their respective
companies.

AMX does not assume responsibility fo r errors or omissions. AMX also reserves the right to alter specifications without p rior notice at any time.
The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax [phone]
AMX (UK) LTD, AMX by HARMAN - Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • [phone] • www.amx.com/eu/