AMX DAS-TAMP4/8-SIG User Manual
Installation Guide
DAS-TAMP4/8-SIG Tango Amplifiers
Overview
Use the DAS-TAMP4-SIG and DAS-TAMP8-SIG Tango Amplifiers (FIG. 1) in
conjunction with Tango Audio Controllers to increase the total number of audio
outputs available to each Controller, per Zone.
FIG. 1 DAS-TAMP4/8-SIG Tango amplifier
Note that each Output on the Tango Amplifier represents two audio channels.
•The DAS-TAMP4-SIG is a 4-channel amplifier that provides two Outputs.
•The DAS-TAMP8-SIG is an 8-channel amplifier that provides four Outputs.
Tango Amplifiers connect to the Tango Controller via one of the Zone Output
connectors on the Controller, and provide either two or four additional Outputs
for that single audio Zone.
Features
• High-quality sound - delivers 60 watts of high-quality sound per channel.
• Expandable - stack up to three Tango amplifiers units per zone to allow up
to 24 channels in a single zone (using the DAS-TAMP8-SIG).
• Easy installation - SWT (Speaker Wire Technology) makes installation
simple using four-conductor speaker wire.
• Integrates with Tango Series, Delta Series and Mi Series controllers, as
well as the W, C, C-DT and EL Series speakers.
Product Specifications
Tango Amplifiers - Product Specifications
Models Available: DAS-TAMP4-SIG 4-Channel amplifier:
• US version (120V) - FG1103-21
• Int’l version (240V) - FG1103-23
DAS-TAMP8-SIG 8-Channel amplifier:
• US version (120V) - FG1103-22
• Int’l version (240V) - FG1103-24
Dimensions (HWD): • 3 1/16” x 17” x 13 1/2” (7.68cm x 43.18cm x 33.52cm)
•RU: 2
Weight: • DAS-TAMP4-SIG: 25.75 lbs (11.68 kg)
• DAS-TAMP8-SIG: 32.30 lbs (14.65 kg)
Power: • High current Torroidal power supply
Stereo Output: • Dual mono amplifier stage design
Configuration: • Modular Design - configurable in single pairs up to either
Control Options: • Metreau Audio Keypads (DAS-MET-6SRC,
Front Panel Components:
Light Bar • Blue light bar indicates power status.
Status LED • Blue LED lights when active
• Maximum: 634 W
Average usage:
• DAS-TAMP4-SIG: 250 W
• DAS-TAMP8-SIG: 500 W
• 60 W per channel (1 KHz continuous .006% @ 8 Ohms
THD+N)
• DAS-TAMP4-SIG: capable of providing 240 watts
@ 8 Ohms
• DAS-TAMP8-SIG: capable of providing 480 watts
@ 8 Ohms
4 stereo pairs (4 channels) 8 stereo pairs (8 channels).
• Stackable (up to 3 Tango amplifiers)
DAS-MET-NUM)
• C-Series speakers using SWT
• IR using a Stealth IR Receiver (DAS-IRRX-SWT)
Tango Amplifiers - Product Specifications (Cont.)
Rear Panel Components:
Power Switch &
Receptacle
OUTPUT connectors
(1-2 or 1-4):
From Controller: SWT input port (connects to a Delta, Mi or Tango Audio
To Keypad: SWT output port (connects to Matrix keypad or interface)
Included Accessories: Power Cord
Other AMX Equipment: DAS-MRMK Mi Series Rack Mount Kit (FG1101-60)
The master power switch normally remains in the ON
position.
4-pin connectors provide direct connection to speakers.
• The DAS-TAMP4-SIG has 2 OUTPUT connectors
• The DAS-TAMP8-SIG has 4 OUTPUT connectors
Controller)
This connector can also be used to connect to a another
Tango amplifier, to allow for expansion (up to three Tango
amplifiers units per zone).
Wiring and Connections
Front and Rear Panel Components
FIG. 2 provides views of the front and rear panels of the Tango amplifiers.
Note that the front panel is identical for both Tango amps, and the only
difference on the rear panel is the number of OUTPUT connectors (2 on the
DAS-TAMP4-SIG, or 4 on the DAS-TAMP8-SIG).
Light Bar (power status)
Status LED
To Keypad
From Controller
Power Switch & Receptacle
Tango amplifiers (DAS-TAMP4-SIG shown)
FIG. 2
Note that each Output on the Tango Amplifier represents two audio channels.
Cabling Instructions
This installation uses low voltage cabling. Prior to installation, be sure to check
for any wiring restrictions required by the electrical code in your area.
The Tango amplifier is cabled using standard four-conductor speaker cable
originating at the Tango Controller, passing through the Keypad, and terminating
at the speaker location.
AMX recommends using a bundled four-conductor 16-gauge stranded copper
wire in a single continuous run.
Connecting Outputs (Speakers)
OUTPUT Connectors
FIG. 3 provides the pinout configuration for the OUTPUT connectors on the
Tango amplifiers.
OUTPUT 1
L+ L- R- R+
FIG. 3 OUTPUT Connectors - Pinout Configuration
L+ = Left audio channel (+)
L- = Left audio channel (-)
R- = Right audio channel (-)
R+ = Right audio channel (+)
Outputs (2 or 4)
Connecting SWT Speakers
SWT Speakers are different from other speakers available on the market. They
allow you to control a single zone of audio without a keypad being installed.
Therefore, some different wiring practices must be considered for proper
operation and control.
This is achieved by “daisy-chaining” from the first speaker to the second
speaker. The main run of 16/4 from the controller will go directly to the first
speaker in the zone.
SWT cabling follows the pinout configuration shown in FIG. 4:
Wiring Diagram - Expanded Configuration
FIG. 6 illustrates stacking up to three Tango amplifiers, to allow up to 12 Outputs
(24 channels) in a single Zone:
Note: Only one Keypad is allowed per Zone.
L = Left audio channel (+)
D = Data/Power (+)
G = Ground (-), also provides return for L/R audio
LDGR
FIG. 4 SWT Connectors - Pinout Configuration
• At the controller end, the wiring is left-to-right: L D G R.
• At the speaker end, refer to the labeling on speaker PCB to ensure the
correct wiring.
The labelling at both ends must match or the IR control will not work (i.e.: if you
used the RED wire for the Left Audio labelled “L” at the zone output, you must
use the RED wire for the pin labelled “L” on the speaker connector).
Note: Be sure to screw the connector down to the speaker crossover board
before installing and securing in the ceiling. This will ensure that the connector
will not disconnect after installation.
A single run of 16/2 must be run from the first speaker to the second speaker.
Connecting Non-SWT Speakers
Each speaker has a Red (positive) terminal and a Black (negative) terminal.
Connect the appropriate wire from the keypad to Red and Black terminals on the
Left and Right speakers, as with any standard speaker installation.
R = Right audio channel (+)
Connecting To a Tango Audio Controller
Connect the amplifier to the Audio Controller via the 4-pin connector labelled
From Controller on the rear panel of the amplifier (see FIG. 5).
Connecting SWT Keypads
Connect SWT Keypads (DAS-MET-6SRC or K-Series) to the amplifier via the
SWT connector labelled To Keypad on the rear panel of the amplifier (see
FIG. 5).
Note: When stripping cable for use with SWT connector, only strip away about
¼” (6mm) of the insulation from each wire. The complete assembly should not
have more than 1/32” (1mm) of bare wire exposed from the bottom of the
connector.
Wiring Diagram - Single Amplifier
FIG. 5 illustrates the connections from a Mi Audio Controller, and to SWT
Speakers and Metreau (SWT) Keypad.
Audio Controller
Tango Amplifier
+
-
8 ohm
-
+
8 ohm
FIG. 5 Single Amp
+
-
8 ohm
-
+
8 ohm
+
-
8 ohm
8 ohm
-
+
8 ohm
DAS-MET-6SRC
Metreau 6-Source Audio Keypad
8 ohm
+
-
-
+
Audio Controller
Tango Amplifier #1
+
-
8 ohm
-
+
8 ohm
+
-
8 ohm
-
+
8 ohm
+
-
8 ohm
-
+
8 ohm
FIG. 6 Expanded Configuration (showing three DAS-TAMP8-SIG 8-Channel Amps)
To "stack" Tango amplifiers, connect the To Keypad connector on the first Tango
amplifier to the From Controller connector on the second amplifier. To add a
third Amp to the configuration, connect the To K e ypa d connector on the second
Amp to the From Controller connector on the third Amp.
The Metreau (SWT) Keypad can be connected serially between the Audio
Controller and the first Amp, or between the first and second Amp, or between
the second and third Amp, or to the To Keypad port on Amp #3 (as shown in
FIG. 6).
• Only one Keypad can be connected in one Zone.
• The Output connectors on the Amplifier are not SWT connectors, and do
not carry a data signal. Therefore, IR control through SWT speakers
connected to the amplifier is not possible. IR Control is achieved via the
Metreau (SWT) Keypad.
+
-
8 ohm
-
+
8 ohm
+
-
8 ohm
-
+
8 ohm
+
-
8 ohm
-
+
8 ohm
+
-
8 ohm
8 ohm
-
+
8 ohm
Tango Amplifier #2
8 ohm
+
-
8 ohm
8 ohm
-
+
8 ohm
Tango Amplifier #3
8 ohm
+
-
8 ohm
8 ohm
-
+
8 ohm
DAS-MET-6SRC
Metreau 6-Source Audio Keypad
8 ohm
+
-
-
+
+
-
-
+
+
-
-
+
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
©2010 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
AMX reserves the right to alter specifications without notice at any time.
2/10
93-1103-21 REV: C
Loading...