AMX DAS-MET-NUM User Manual
Installation Guide
DAS-MET-NUM Metreau™ Numeric Audio Keypad
Overview
Used in conjunction with the DAS-MET-6SRC Metreau keypad, the
DAS-MET-NUM Metreau numeric keypad (FG1122-02) provides direct numeric
access, setting & recalling presets, and access to advanced functionality such as
grouping, Setting Favorites, Alarm, and Keypad lockout functionality. (FIG. 1).
The DAS-MET-NUM Metreau numeric keypad connects to the main
DAS-MET-6SRC keypad via a 14-pin connector (FIG. 2).
12 pre-printed pushbuttons
ENTER button
(with LED to
provide feedback)
FIG. 1 DAS-MET-NUM Metreau Numeric Audio Keypad
The DAS-MET-NUM is a SWT keypad, suitable for use in Matrix Distributed
Audio Systems.
Specifications
DAS-MET-NUM Specifications
Power: 12 VDC, 125 mA
Front Panel
Components:
Rear Panel
Components:
Dimensions
(HWD):
Weight:
Operating
Environment:
Certifications: • FCC Class B
Colors: • White (FG1122-02-WH)
Optional
Accessories:
Pushbuttons - 13 tactile pushbuttons.
Wiring connection - One 14-pin connector that provides
connection to the main 6 Source Metreau Keypad
(DAS-MET-6SRC).
• Keypad and Mounting Plate: 4.055" x 1.772" x 0.818"
(103mm x 45mm x 207mm)
• Mounts into standard decora-style wall plates.
2.4 oz. (68.04 g)
• Operating Temperature: 32° - 104° F (0°- 40° C).
• Relative Humidity: 5% - 85%, non-condensing.
• Intended for indoor use only.
•CE
• IEC60950
•RoHS
• Black (FG1122-02-BL)
• Light Almond (FG1122-02-LA)
• Single Button Kit (FG5794-10)
• Double Button Kit (FG5794-11)
• Lutron Cairo Wallplates (available in a variety of sizes and
colors)
Installation
Note: Before touching the device, discharge the static electricity from your body
by touching a grounded metal object.
FIG. 2 shows the basic rear components of the DAS-MET-NUM keypads:
14-pin connector
(from DAS-MET-6SRC)
Circuit Board
Mounting Plate
DAS-MET-NUM - Rear Components
FIG. 2
Wiring
The DAS-MET-NUM Metreau numeric keypad connects to the main
DAS-MET-6SRC keypad via a 14-pin connector, as indicated in FIG. 3:
Pin #1 Pin #1
14-pin connector
FIG. 3 DAS-MET-NUM connected to main DAS-MET-6SRC keypad
• The red line on the cable indicates Pin #1.
• The cable cannot be twisted, it must be straight across (pin1 to pin1).
14-pin connector
DAS-MET-NUMDAS-MET-6SRC
Mounting Procedures
AMX recommends mounting Metreau keypads in standard U.S.-style decora
wallboxes:
• Conduit box should meet NEC specs (section 370)
• Minimum internal clearance of (HWD) 2-5/8" x 1-3/4" x 1-5/8".
Note: Before touching the device, discharge the static electricity from your
body by touching a grounded metal object.
Wallbox Mounting
1. Use the cutout dimension for the wallbox to cutout the install surface.
2. Connect the AxLink connector (or SWT cable connectors) to the rear of
the keypad.
3. Place the Mounting Plate on the wallbox; align the screw holes with the
mounting holes and fasten the Mounting Plate to the wallbox using the
screws supplied.
Note: Do not overtighten the screws when mounting the Mounting Frame. The
device should be flush with mounting surface.
Mounting Dimensions
FIG. 4 provides detailed dimensions for the 13-button Metreau keypads.
FIG. 4 Mounting Dimensions - DAS-MET-NUM
Programming
SWT-only Metreau keypads (DAS-MET-6SRC and DAS-MET-NUM) are
configured via the Tango Audio Controller. Refer to the Tango Audio Controllers
Operation / Reference Guide for details.
Additional Documentation
Refer to the Metreau Keypads Operation/Reference Guide (available online
www.amx.com) for additional information on configuration, programming and
using the Metreau keypads.
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
©2008 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
AMX reserves the right to alter specifications without notice at any time.
1/08
93-1122-02 REV: A
Loading...