AMX CTP-1301 Installation Guide
QUICK START GUIDE
CTP-1301
Connectivityand TransportKit - Presentations
•
[1] CTP-1301 TX
•
[1] CTP-1301 RX
•
[1] DC 12V 3A Power Adapter (with US, UK, AUS and
•
[5] Phoenix Male Connector (3.5mm, 3 Pins)
•
[4] Mounting Bracket
•
Voltage, DC (typical): 12V DC 3A
•
Power consumption (max): 7.15W(TX) + 26.83W(RX)
•
Operating Temperature: 32° F (0° C) to 122° F (50°C)
•
Storage Temperature: 14° F (-10° C) to 140° F (60° C)
•
Operating Humidity: 5% to 85% RH (non-condensing)
•
Storage Humidity: 5% to 85% RH (non-condensing)
1.
Connect video source:
2.
Connect HDBT OUT:
3.
Connect HDMI IN:
4.
Connect HDMI OUT:
5.
Connect AUDIO OUT:
6.
Connect for additional control options:
7.
RS232 Pass-through:
8.
Connect the power adapter provided to the CTP-1301 RX: One-
9.
Power on all attached devices:
2.
Repeat steps 1 for the CTP-1301 TX/RX.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 | www.AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153
Overview
This guide pertains to the CTP-1301 Presentation Connectivity and
Transport Kit (FG1010-710) featuring four inputs with an integrated
4K scaler. The purpose of this document is to illustrate how the
device is to be installed and set up in its simplest configuration by a
trained technician.
What’s in the Box?
The following items are included with the CTP-1301:
Euro Power Cords)
Power
Active power requirements:
Environmental Requirements
The environmental requirements for the CTP-1301 are as follows:
Installation
Connections
Connect the VGA and HDMI sources (such as PC,
Blu- ray player, Apple TV, 4K media player, etc) to
the VGA IN and HDMI IN ports of the CTP-1301 TX.
If required, LAN Control (Telnet/Web UI): Connect a PC or
control system to the LAN port of the CTP-1301 RX.
If required, connect the RS232-enabled device (e.g. projector)
to RS232 port of the CTP-1301 RX, and connect the projector
screen to RELAY port (1-2) for RS232 signal pass- through.
way PoH enables power to be sent from CTP-1301 RX to TX along
a single CATX cable, and no additional power adapter is
required at the TX.
When all is set, check if all LED indicators on the CTP-1301 TX and
RX are normal to ensure installation is successful. For LED
indication, please refer to Panel Description section of the
owner's manual.
Identify the IP addres s of the CTP-1301
On the CTP-1301 RX, press and hold the HDBT and HDMI Input
buttons for 3 seconds. The current IP address of the device will be
presented on the display connected to the HDMI Out port. Please
note that if the address is typed as http:// or if on
ly the IP address is
typed, it will be redirected to a secure port on an HTTPS://
connection. Also note that the included certificate will most likely
need to be trusted at least once by each browser the first time the
web interface is connected.
From the web interface, the device can be configured with NetLinx
D:P:S configuration, adjust output volume, change IP address, enable
manual switching, etc.
Attaching Installation Brackets
To attach the installation brackets:
1.
Position and install the mounting brackets with thefour
mounting screws provided.
CTP-1301 TX
CTP-1301 RX
Connect HDBT OUT of the CTP-1301 TX to HDBT IN of
a receiver like the CTP-1301 RX with a shielded Cat
6/6A/7 cable.
Connect an HDMI source to the HDMI IN port of
the CTP-1301 RX.
Connect an HDMI display device (such as projector
or display) to the HDMI OUT port on the CTP-1301 RX.
If Required, Connect an audio receiver to the AUDIO OUT of
the CTP-1301 RX.
Typical Connection Diagram
Blu-ray PlayerPCPC
VGA IN
CTP-1301 TX
AUDIO
IN
IN
© 2017 Harman. All rights reserved. Modero, AMX, AV FOR AN IT WORLD, HARMAN, and their respective logos are registered trademarks
of HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of their respective
companies. AMX does
at any time. The AMX Warranty and Return Policy and related documents can be viewed/downloaded atwww.amx.com.
AMX (UK) LTD, AMX by HARMAN - Unit C, Auster Road, Clifton Moor, York, YO30 4GD United Kingdom | +44 1904-343-100 | www.amx.com/eu/
HDMI INHDMI
not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice
3. Mount and secure the CTP-1301
location with the mounting screws.
Additional Documentation
Refer to the AMX CTP-1301 Presentation Connectivity and
Transport Kit users guide for additional details on installing,
upgrading, and controlling the CTP-1301.
HDBT
CTP-1301 RX
PC
Ethernet
Control System
(e.g. NX-3200)
Ethernet
Ethernet Switch
Ethernet
TX/RX to a surface or a suitable
AUDIO
HDMI IN Relay
HDMI
OUT
OUT
Amplifier
RS232
Control
Projector ScreenProjectorBYOD System
5100545 REV:B
Last Revised: 10/11//2018
Loading...