AXF-MINI
Axcess MINI CardFrame
instruction manual
Axcess Central Controllers
AMX Limited Warranty and Disclaimer
AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for
three (3) years from the date of purchase from AMX Corporation, with the following exceptions:
• Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch
overlay components that are warranted for a period of one (1) year.
• Disk drive mechanisms, pan/tilt heads, power supplies, MX Series products, and KC Series products are
warranted for a period of one (1) year.
• Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year.
• Software is warranted for a period of ninety (90) days.
• Batteries and incandescent lamps are not covered under the warranty.
This warranty extends only to products purchased directly from AMX Corporation or an Authorized AMX Dealer.
AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform.
This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is not
liable for any claim made by a third party or by an AMX Dealer for a third party.
This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort
claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of
liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX
Corporation or an authorized representative of AMX Corporation has been advised of the possibility of any such
damages. This limitation of liability, however, will not apply to claims for personal injury.
Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or
exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of
the Limited Warranty may not apply. This Limited Warranty gives the owner specific legal rights. The owner may
also have other rights that vary from state to state. The owner is advised to consult applicable state laws for full
determination of rights.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES NO
OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX CORPORATION
EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY
IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS
LIMITED WARRANTY.
Table of Contents
Table of Contents
Product Information .................................................................................................1
Specifications .................................................................................................................... 1
Power Configuration Options ............................................................................................ 2
Server/Remote PWR................................................................................................................ 2
Server/Local PWR.................................................................................................................... 2
Master ...................................................................................................................................... 3
AXF-MINI Axcess MINI CardFrame
i
Table of Contents
ii
AXF-MINI Axcess MINI CardFrame
Product Information
The AXF-MINI Axcess Mini-CardFrame can be used as a stand-alone control system or as an add-
on to existing Axcess or Axcent
Enhanced Master card (AXC-EM) and up to three optional AXC control cards. The add-on
configuration uses up to three optional AXC cards and is connected via the AXlink data/power bus
along with control panels and AXB AXlink controllers. The MINI CardFrame features a new
backplane design incorporating all card server functions, eliminating the need for a dedicated card
slot. The CardFrame can be easily installed into a rack, shelf, or at a remote site to avoid costly
cable runs.
2
AXC-EM Enhanced Master Card
Product Information
systems. The stand-alone configuration uses an optional AMX
Cable Support Bracket (optional)
Built-in Card Server
Three AXC Control
Card Slots
FIG. 1
AXF-MINI Axcess Mini-CardFrame
Specifications
The following table lists the specifications for the AXF-MINI.
AXF-MINI Specifications
Dimensions (HWD): 1.75" x 17" x 13.64" (4.5 cm x 43.2 cm x 34.7 cm)
Weight: 5.5 lbs. (2.49 kg)
Backplane Components:
Master Card Slot One master processor card slot.
Control Card Slots 1 - 3 Three standard Axcess control card connections (slots 1, 2, and 3).
Slots 1 - 3 are wired according to the installed card. Refer to the appropriate cards wiring information for instructions.
AXlinx connector Install AXlink data/power bus wiring as shown below after device num-
PWR Connector The three PWR wiring configurations are:
ber is set. Remove and reconnect AXlink terminal after changing
device number to enter the new number in memory.
• Server/Remote power
• Server/Local power
•Master
Refer to the
on each configuration.
Power Configuration Options
section for wiring information
AXF-MINI Axcess Mini-CardFrame
1
Product Information
AXF-MINI Specifications
Backplane Components (Cont.):
Device DIP switch The DEVICE DIP switch is used to set SLOT 1 of the CardFrame to
Mounting options • Rack, shelf, or wall mounting; rack mount ears can be removed or
one of 255 devices in an Axcess or Axcent
slot in the CardFrame is automatically assigned to the next device
number. The device number is set by the total of all ON (up) switches.
See the chart below. For example, the DIP switch below is set for
device number 18 (2 + 16 = 18).
Switch
ON
pivoted 90 degrees.
• Optional cable support bracket with three-step adjustment for rack or
shelf installation.
ON Va lue
2
system. Each subsequent
1 1 2 2 3 4 4 8 5
16 6 32 7 64 8 128 1 2 3 4 5 6 7 8
Power Configuration Options
Server/Remote PWR
2
Connects AXlink to Axcess or Axcent
12 VDC +
PWR
AXlink
-
PWR
AXP
AXM
GND
systems, with power provided by AXlink (FIG. 2).
PWR
AXP
AXM
GND
System
FIG. 2
Power supplied by AXlink
Server/Local PWR
2
Connects AXlink to Axcess or Axcent
systems, with power provided by a local power supply
(FIG. 3).
12 VDC +
PWR
AXlink
FIG. 3
Power supplied by local power supply
PWR
AXP
AXM
GND
-
PWR
AXP
AXM
GND
Do not connect PWR on the AXlink bus.
Power Supply
System
2
AXF-MINI Axcess Mini-CardFrame
Product Information
Master
Connect the 12 VDC power supply to the backplane and wire AXlink to remote devices (FIG. 4).
12 VDC +
PWR
AXlink
FIG. 4
Power supplied by backplane on the Master
-
PWR
AXP
AXM
GND
PWR
AXP
AXM
GND
Power Supply
To AXlink device
AXF-MINI Axcess Mini-CardFrame
3
AMX reserves the right to alter specifications without notice at any time.
2001 AMX Corporation. All rights reserved. AMX, the AMX logo, the building icon, the home icon, and the light bulb icon are all trademarks of AMX Corporation.
©
brussels • dallas • los angeles • mexico city • philadelphia • shanghai • singapore • tampa • toronto • york
3000 research drive, richardson, TX 75082 USA • 469.624.8000 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993
030-004-1033 9/01
AMX reserves the right to alter specifications without notice at any time. *In Canada doing business as Panja Inc.
Loading...