AMX ALD-H48 User Manual
ALD-H48
Network Lighting Solution
instruction manual
Lighting Control
AMX Limited Warranty and Disclaimer
AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three
(3) years from the date of purchase from AMX Corporation, with the following exceptions:
• Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch
overlay components that are warranted for a period of one (1) year.
• Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one
(1) year.
• AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting
products, as long as the AMX Lighting products are under warranty. AMX Corporation does guarantee the
control of dimmable loads that are properly connected to our lighting products. The dimming performance or
quality cannot be guaranteed due to the random combinations of dimmers, lamps and ballasts or transformers.
• Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year.
• AMX Software is warranted for a period of ninety (90) days.
• Batteries and incandescent lamps are not covered under the warranty.
This warranty extends only to products purchased directly from AMX Corporation or an Authorized AMX Dealer.
All products returned to AMX require a Return Material Authorization (RMA) number. The RMA number is
obtained from the AMX RMA Department. The RMA number must be clearly marked on the outside of each box.
The RMA is valid for a 30-day period. After the 30-day period the RMA will be cancelled. Any shipments received
not consistent with the RMA, or after the RMA is cancelled, will be refused. AMX is not responsible for products
returned without a valid RMA number.
AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform.
This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is not
liable for any claim made by a third party or by an AMX Dealer for a third party.
This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort
claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of
liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX Corpo-
ration or an authorized representative of AMX Corporation has been advised of the possibility of any such damages.
This limitation of liability, however, will not apply to claims for personal injury.
Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or
exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of
the Limited Warranty may not apply. This Limited Warranty gives the owner specific legal rights. The owner may
also have other rights that vary from state to state. The owner is advised to consult applicable state laws for full
determination of rights.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES NO
OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX CORPORATION
EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY
IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS
LIMITED WARRANTY.
Software License and Warranty Agreement
LICENSE GRANT.
AMX grants to Licensee the non-exclusive right to use the AMX Software in the manner described in this License. The AMX Software
is licensed, not sold. The AMX Software consists of generally available programming and development software, product
documentation, sample applications, tools and utilities, and miscellaneous technical information. Please refer to the README.TXT
file on the compact disc or download for further information regarding the components of the AMX Software. The AMX Software is
subject to restrictions on distribution described in this License Agreement. YOU MAY NOT LICENSE, RENT, OR LEASE THE AMX
SOFTWARE. You may not reverse engineer, decompile, or disassemble the AMX Software.
INTELLECTUAL PROPERTY.
The AMX Software is owned by AMX and is protected by United States copyright laws, patent laws, international treaty provisions,
and/or state of Texas trade secret laws. Licensee may make copies of the AMX Software solely for backup or archival purposes.
Licensee may not copy the written materials accompanying the AMX Software.
TERMINATION. AMX RESERVES THE RIGHT, IN ITS SOLE DISCRETION, TO TERMINATE THIS LICENSE FOR
ANY REASON AND UPON WRITTEN NOTICE TO LICENSEE.
In the event that AMX terminates this License, the Licensee shall return or destroy all originals and copies of the AMX Software to
AMX and certify in writing that all originals and copies have been returned or destroyed.
PRE-RELEASE CODE.
Portions of the AMX Software may, from time to time, as identified in the AMX Software, include PRE-RELEASE CODE and such
code may not be at the level of performance, compatibility and functionality of the final code. The PRE-RELEASE CODE may not
operate correctly and may be substantially modified prior to final release or certain features may not be generally released. AMX is
not obligated to make or support any PRE-RELEASE CODE. ALL PRE-RELEASE CODE IS PROVIDED "AS IS" WITH NO
WARRANTIES.
LIMITED WARRANTY.
AMX warrants that the AMX Software will perform substantially in accordance with the accompanying written materials for a period of
ninety (90) days from the date of receipt. AMX DISCLAIMS ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, WITH REGARD TO THE AMX SOFTWARE. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.
Any supplements or updates to the AMX SOFTWARE, including without limitation, any (if any) service packs or hot fixes provided to
you after the expiration of the ninety (90) day Limited Warranty period are not covered by any warranty or condition, express, implied
or statutory.
LICENSEE REMEDIES.
AMX's entire liability and your exclusive remedy shall be repair or replacement of the AMX Software that does not meet AMX's
Limited Warranty and which is returned to AMX. This Limited Warranty is void if failure of the AMX Software has resulted from
accident, abuse, or misapplication. Any replacement AMX Software will be warranted for the remainder of the original warranty period
or thirty (30) days, whichever is longer. Outside the United States, these remedies may not available.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL AMX BE LIABLE FOR ANY DAMAGES
WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS
INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF OR
INABILITY TO USE THIS AMX SOFTWARE, EVEN IF AMX HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
BECAUSE SOME STATES/COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
U.S. GOVERNMENT RESTRICTED RIGHTS. The AMX Software is provided with RESTRICTED RIGHTS. Use, duplication, or
disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of The Rights in Technical Data and
Computer Software clause at DFARS 252.227-7013 or subparagraphs (c)(1) and (2) of the Commercial Computer Software
Restricted Rights at 48 CFR 52.227-19, as applicable.
This Agreement replaces and supercedes all previous AMX Software License Agreements and is governed by the laws
of the State of Texas, and all disputes will be resolved in the courts in Collin County, Texas, USA. Should you have any
questions concerning this Agreement, or if you desire to contact AMX for any reason, please write: AMX Corporation,
3000 Research Drive, Richardson, TX 75082.
Table of Contents
Table of Contents
Overview ....................................................................................................................1
Getting Started ..........................................................................................................3
Step 1: Downloading The ALD-H48 Workspace .............................................................. 3
Step 2: Setting The ALD-H48 IP Address ........................................................................ 3
Step 3: Opening The ALD-H48 Workspace ..................................................................... 3
Step 4: Transferring The ALD-H48 Project to A NetLinx Master...................................... 4
Using The Web Interface ..........................................................................................5
Addressing The Dimmers via The Web Interface.............................................................. 5
Controlling Dimmers via The Web Page ........................................................................... 7
Establishing And Modifying Scenes .................................................................................. 8
Establishing And Modifying Groups ................................................................................ 10
Using The Touch Panel Pages ..............................................................................11
Touch Panel Main Page .................................................................................................. 11
Dimmer Light Adjustment ....................................................................................................... 12
Setup Page...................................................................................................................... 13
Addressing Dimmers .............................................................................................................. 14
Setting Unique Names ........................................................................................................... 14
Groups Page ................................................................................................................... 14
Creating A Group ................................................................................................................... 15
Scenes Page ................................................................................................................... 16
Creating A Lighting Scene ..................................................................................................... 17
Deleting A Lighting Scene ...................................................................................................... 17
Advanced Programming ........................................................................................19
Introduction...................................................................................................................... 19
Overview ......................................................................................................................... 19
Implementation................................................................................................................ 20
Port Mapping ................................................................................................................... 21
Channel Assignment and Feedback ............................................................................... 21
Command Interface......................................................................................................... 23
Command Feedback ....................................................................................................... 30
Device Notes ................................................................................................................... 33
Programming Notes ........................................................................................................ 34
Adding Functions to Modules .......................................................................................... 36
Commands to The Device...................................................................................................... 36
Updating The ALD-H48 Firmware .........................................................................37
ALD-H48 Lighting Controller
i
Table of Contents
Via 232 ............................................................................................................................ 37
Via Ethernet: ................................................................................................................... 37
ii
ALD-H48 Lighting Controller
Overview
The ALD-H48 from AMX is a Lutron lighting solution with a complementary Duet module. The
result is a Lutron device that functions within a NetLinx project.
After you have installed the ALD-H48, using the installation documentation included with the unit,
you can create a NetLinx project and configure the dimmers. You need NetLinx Studio v2.3 or
higher and a NetLinx Master capable of running Duet modules (firmware version 3.0.XXX or
higher).
Using the web interface capabilities of your NetLinx master you can configure dimmers connected
to your ALD-H48.
The web interface supports:
Overview
Internet Explorer v 6.0 (and higher)
Mozilla Firefox v 1.0 (and higher)
ALD-H48 Lighting Controller
1
Overview
2
ALD-H48 Lighting Controller
Getting Started
Step 1: Downloading The ALD-H48 Workspace
First you must attain the ALD-H48 Workspace file (.AXW). To download the Duet module go to
either amx.com > Dealers > InConcert or the Product Catalog page for the ALD-H48. From the
InConcert page you can search for and download the ALD-H48 Duet module, they are indicated by
the D within the legend displayed below.
FIG. 1 Module Legend
Included in the .AXW file:
The NetLinx Main Code (.AXS)
The Duet module (.JAR)
Associated TPD4 files
Getting Started
Step 2: Setting The ALD-H48 IP Address
In order for the NetLinx Master to locate the ALD-H48, you must set the IP address for the device.
1. Connect your PC to the H48 serial port using a standard DB-9 serial cable.
2. Open your preferred serial client (HyperTerm, TELNET, etc...)
3. Make sure your serial connection baud rate and handshaking settings match the H48 serial
settings. (Default Baud Rate 9600, Data Bits: 8, Parity: None, Stop Bits: 1, Flow Control:
None)
4. Upon a successful connection, you are prompted with L232>. At the prompt type SETIP,1,
xxx.xxx.xxx.xxx . Follow the onscreen instructions from this point.
(Where 1 is the number of processors present on the H48 and xxx.xxx.xxx.xxx is the IP
address to be decided by you.)
Further, at the prompt type HELP and a list of all supported command is displayed. In order to get
the correct syntax to set the IP address type at the prompt HELP, SETIP.
Step 3: Opening The ALD-H48 Workspace
After you have downloaded the ALD-H48 Workspace file you need to open your NetLinx project.
The .AXW file provided by AMX is intended to be a starting point for your ALD-H48 project.
1. Launch NetLinx Studio v2.3 or higher.
2. Select File > Open Workspace to launch the Open Workspace dialog.
3. Browse to the location where you saved the ALD-H48 Workspace file (.AXW) and click
Open.
4. Manually enter the IP address assigned to the ALD-48 within Lutron_H48_UI.axs and then
recompile the project before transferring it to the NetLinx Master.
ALD-H48 Lighting Controller
3
Getting Started
You can also make any additional edits to the ALD-H48 project or elect to send the file to the
NetLinx Master as is.
There is a "simple" version of the ALD-H48 files. These files are intended for
demonstration purposes only.
Step 4: Transferring The ALD-H48 Project to A NetLinx Master
NetLinx Studio can transfer the ALD-H48 project file to any connected NetLinx Master with
firmware version 3.XX or higher.
1. Select Tools > File Transfer to open the File Transfer dialog.
2. If the Workspace file is not already listed in the window click Quick Load to open the
corresponding dialog.
3. In the drop down list select the ALD-H48 Workspace.
4. Click Select All.
5. Click OK.
6. Make sure there is a check in the box next to the ALD-H48 workspace within the File Transfer
dialog and click Send.
4
ALD-H48 Lighting Controller
Using The Web Interface
Addressing The Dimmers via The Web Interface
Once you have installed the ALD-H48 and dimmers using the hardware installation literature
included with the unit, you must now address the dimmers.
You can only select addresses available on the bus to which the dimmer is physically connected.
For example, if you want to assign address 17 to a particular dimmer, it must be connected to bus 3
of the ALD-H48 as indicated below.
Bus Address Location
Bus Address
11-8
29-16
3 17-24
4 25-32
5 33-40
6 41-48
Using The Web Interface
To address the dimmers:
1. Using your web browser, go to the target NetLinx Master’s web page.
Refer to the NetLinx Master documentation for more detailed information concerning
the NetLinx Master Web Interface.
2. Click on Lights and all connected modules are displayed below Lights. There is only one
module per device.
Upon your first visit to Lights, the page will have the following message, FIG. 2.
FIG. 2 Initial Lights Configuration Page
3. Click Address Mode to set the master to look for available dimmers.
4. Tap the dimmer you wish to address three times to make it available to the
master.
5. The displayed addresses are only those that are available on that physical bus that have not
been used. Bold text indicates the address has already been assigned. Pick an available number
and click Select to address the dimmer.
ALD-H48 Lighting Controller
5
Using The Web Interface
FIG. 3 Dimmer Address
6
ALD-H48 Lighting Controller
Using The Web Interface
Controlling Dimmers via The Web Page
Once a dimmer has been addressed, you have access to a few basic level controls from the master’s
web page.
1. Click the button Dimmer Control to open the Dimmer Control page. (FIG. 4)
FIG. 4 Dimmer Control
Listed in the column on the left are all dimmer addresses available for control. On the right is a
percentage bargraph representation of the current state of the selected dimmer.
2. To change the state of a dimmer, select a dimmer address in the column on the left.
Click on 100% to ramp the dimmer completely on and 0% to ramp the dimmer off.
Click within the bargraph area on the right to shift the dimmer state up and down to a
ALD-H48 Lighting Controller
desired percentage.
7
Using The Web Interface
Establishing And Modifying Scenes
Once your dimmers have been addressed and states set, you can create a scene. A scene is a
collection of dimmers with specific states for each dimmer, i.e., Scene 1 could be set as a meeting
scene where Dimmers 1 and 12 ramp down to 45%, Dimmers 6 and 14 ramp to 80% and Dimmers
2 through 5 ramp to 0% and all dimmers delay 10 seconds after the scene is selected before
initiating. A dimmer can be a part of many different scenes. To create a scene:
1. Click the Scenes button at the top of the page. Shown below is the Scene page.
FIG. 5 Scene Page
2. Click the Modify button for the Scene you would like to set. This opens the Modify Scene
page.
8
ALD-H48 Lighting Controller
Loading...