Operate at ISM frequency Band (2.4GHz)
IEEE Standards Support, 802.11b, 802.11g and 802.11n
The WN4608R is developed using single-chip designed by Ralink Technology
Corporation
USB 2.0 support for date rates up to 12Mbps full speed and 480Mbps high speed
Enterprise level security supporting: WPA, WPA2, WEP 64/128
Support 1 transmission and 1 receiving, transmission rate can up to 150Mbps
(Physical Rate) in downstream and upstream
Full feature software utility for easy configuration and management
RoHS compliance
Low Halogen compliance
AmTRAN
WN4608R Specification Page 3/12 2011/12/12
PRODUCT SPECIFICATIONS
MAIN CHIPSET
MAC/ Baseband/ RF: Ralink RT5370 (Cu wire bounding)
FUNCTIONAL SPECIFICATIONS
WiFi Function
AmTRAN
Standard
Bus Interface
Data Rate
Media Access Control
Modulation Techniques
Network Architecture
Operation Channel
Frequency Range
Transmit Output Power –
1x1
(Tolerance: +-1.5dBm)
Receive Sensitivity
IEEE802.11b; IEEE 802.11g; IEEE 802.11n
Universal Serial Bus (USB2.0)
3.3V ±10% I/O supply voltage
Microsoft Windows XP/Vista/Win7
TX Mode:
243 mA
RX Mode:
176 mA
Standby Mode:
51 mA
Two Antenna Connectors
PCB
Immersion Gold plating
Layer stack
WN4608R Specification Page 5/12 2011/12/12
MECHANICAL
Module
AmTRAN
Tolerance: ±0.1mm
WN4608R Specification Page 6/12 2011/12/12
Shielding case
AmTRAN
PRODUCT PICTURE
TOP BOTTOM
WN4608R Specification Page 7/12 2011/12/12
CONNECTOR
AmTRAN
WN4608R Specification Page 8/12 2011/12/12
BLOCK DIAGRAM
AmTRAN
EPROM INFORMATION
E
Reg Domain
Vendor ID
Product ID
ENVIRONMENTAL
Operating
Operating Temperature: 0 to 75 °C (32 to 167 °F)
Relevant Humidity: 5-90% (non-condensing)
Storage
Temperature: -40 to 85 °C (-40 to 185 °F)
Relevant Humidity: 5-95% (non-condensing)
US: Channel 1~11 Active Scan
Offset 0x38 for 5G: 0x00
Offset 0x39 for 2.4G: 0x00
0x148F
0x5370
WN4608R Specification Page 9/12 2011/12/12
RELIABILITY REQUEST
AmTRAN
WN4608R Specification Page 10/12 2011/12/12
AmTRAN
FCC WARNING STATEMENT
Class B:
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device
could void the user's authority to operate the equipment.
Labeling requirements
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may
be installed such that 20cm may be maintained between the antenna and users. The
final end product must be labeled in a visible area with the following: "Contains FCC
ID: MDZLTRT5370-WL ”
WN4608R Specification Page 11/12 2011/12/12
AmTRAN
RF exposure warning
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not
be co-located or operating in conjunction with any other antenna or transmitter.
End-users and installers must be provide with antenna installation instructions
and transmitter operating conditions for satisfying RF exposure compliance.
FCC NOTICE: To comply with FCC part 15 rules in the United States, the system
must be professionally installed to ensure compliance with the Part 15 certification. It
is the responsibility of the operator and professional installer to ensure that only
certified systems are deployed in the United States. The use of the system in any
other combination (such as co-located antennas transmitting the same information) is
expressly forbidden.
Only the antennas listed below are allowed to be used with the EUT output power.
Antenna List
No. Manufacturer Model No. Peak Gain NOTE
1
MAG.LAYERS MSA-3420-25GC4-A1
-B160MM
2
MAG.LAYERS MSA-3414-25GC4-A1
-B160MM-RF
NOTE:
1. There are two different EUT output power for with ground plane antenna and
without ground plane antenna.
2. About Output power, please refer to present document page 4: Functional Specifications.
2.37 dBi in 2.4GHz
3.97 dBi in 2.4GHz
without metal reflector
(High CTL Power)
with metal reflector
(Low CTL Power)
WN4608R Specification Page 12/12 2011/12/12
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.