AMS Manuals & Guides: AMS Wireless Vibration Monitor Quick User Guide | AMS Manuals & Guides

AMS Wireless
Vibration Monitor

QUICK USER GUIDE

This document is intended to provide basic information about
installation and configuration as well as information regarding
safety and approvals. For more information, please reference
the User Guide (P/N MHM-97927-PBF) on the Emerson website.

Emerson
Reliability Solutions

835 Innovation Drive, Knoxville, TN 37932 USA

[phone]
[phone]

www.emerson.com/ams

©2020, Emerson.

The contents of this publication are presented for
informational purposes only, and while every effort has
been made to ensure their accuracy, they are not to be
construed as warranties or guarantees, express or implied,
regarding the products or services described herein or their
use or applicability. All sales are governed by our terms and
conditions, which are available on request.
We reserve the right to modify or improve the designs
or specifications of our products at any time without notice.

All rights reserved. AMS is a mark of one of the Emerson
group of companies. The Emerson logo is a trademark and
service mark of Emerson Electric Co. All other marks are the
property of their respective owners.

MHM-97928-PBF, Rev 1
August 2020

Device Preparation

For safety reasons, the device is shipped with the battery
disconnected. When you are ready to configure the device,
follow the steps below to reconnect the battery.

1. Use your hands to unscrew and remove the blue cover.

2. Remove the battery with the pull tab.

3. Locate the battery connector and plug it into the
socket on the device as shown.

4. Replace the battery. Tuck the wires against the battery
and lock them into place.

Quick Configuration

1. Locate the terminals for the communication port
on the opposite side of the device.

2. Connect a configuration device to the terminals such
as a computer running AMS Device Manager with a
HART™ modem or an AMS Trex Field Communicator
(shown below).

3. Follow the onscreen instructions to configure the
device. It is advisable to use the option for Guided
Setup. Individual parameters can be easily customized
later using AMS Device Manager after the device has
joined the wireless network.

4. After configuring the device, make sure to disconnect
the battery before replacing the cover. This not only
conserves battery power, but the battery will need to
be removed again when using the recommended field
installation method.

Field Installation

1. To stud mount the device (recommended),
prepare the machine surface using a spot face tool.
Then drill and tap a ¼-28” hole 0.25” (6.35mm) deep.
Alternately, a mounting pad with ¼-28” thread can be
glued in place using epoxy. (Consult the User Guide
for additional mounting options and instructions.)

2. With the cover still on the device, use your hand
to loosely screw the device into the threaded hole.
Do not tighten.

3. Remove the cover and battery.

4. Insert a small screwdriver through the guide hole in the
base of the unit (shown below) and use this to hold the
device in the desired orientation.

5. While maintaining the device orientation, use a 3/16”
ball driver to tighten the captive screw in the center
of the base (shown above) to 2-5 ft-lb.

6. Then connect and replace the battery.

7. Use your hand to replace and tighten the cover.

Shipping Considerations

Contact Emerson Product Support to obtain a Return
Materials Authorization (RMA) number and receive
additional instructions.

Primary lithium batteries are regulated in transportation by
the U.S. Department of Transportation, and are also covered
by IATA (International Air Transport Association), ICAO
(International Civil Aviation Organization), and ADR
(European Ground Transportation of Dangerous Goods).

It is the responsibility of the shipper to ensure compliance with
these or any other local requirements. Please consult current
regulations and requirements before shipping.

Product Certifications

The AMS Wireless Vibration Monitor has a number of
certifications and approvals including CE, FCC, ISED, RED, CSA,
and ATEX. For a complete list of product certifications, see

http://www.emerson.com/AMSVibrationMonitor.

Safety Information

For personal and system safety, and for optimum product
performance, care should be given to read and understand the
user documentation before installing, using, or maintaining
this device. For more information, see the AMS Wireless
Vibration Monitor User Guide.

For questions, contact customer support:

Inside US (Toll free): 1-800-999-9307
or 1-800-654-7768,
International: 1-[phone],
E-mail: [e-mail]

Battery Information

The AMS Wireless Vibration Monitor uses a standard battery.
For safety reasons, however, the unit was shipped to you with
the battery disconnected. You will need to connect the battery
before configuring and installing the device.

Replacing the battery

The battery may be replaced in hazardous locations.
Replace the battery only with Tadiran Part Number TL-4920/VE
or Emerson Part Number A0702PPU. Follow the instructions
in the User Guide for replacing the battery.

Installation Considerations

When choosing an installation location and position, consider
the need for access to the device. For best overall performance,
the device should be installed vertically. If it is necessary to
install the device horizontally pay special attention to the
network arrangement.

Installation in Hazardous Areas

The device is covered by a hazardous area rating. It is the
responsibility of the user to verify that the device has the
necessary approvals required for the intended area of use.

Warning: Installation in an explosive environment must be in
accordance with the appropriate local, national, and international
standards, codes, and practices. Please review this document for
any restrictions associated with safe installation.

Temperature Limits

As a safety precaution, the following limits must be observed
for ambient temperature:

1. Storage Temperature :–40 to 185 °F / –40 to 85 °C

2. Operating Temperature: –40 to 185 °F / –40 to 85 °C

General Notice

If the device has been exposed to a hazardous substance, a
Safety Data Sheet (SDS) must be included with the returned
materials. An SDS is required by law to be available to people
exposed to specific hazardous substances.

Wireless Certifications

Telecommunications compliance

All wireless devices require certification to ensure that they
adhere to regulations regarding the use of the RF spectrum.
Nearly every country requires this type of product certification.
Emerson works with governmental agencies around the
world to supply fully compliant products and remove the
risk of violating country directives or laws governing
wireless device usage.

Radio Equipment Directive (2014/53/EU)

Emerson complies with the Radio and Equipment Directive.

FCC approvals

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to a radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician
for help.

• This device must be installed to ensure a minimum antenna
separation distance of 20cm from all persons

Radio Approvals

Country Approval Status

Brazil PENDING

Canada IC: 3434A-A9530M1

Ecuador PENDING

Hong Kong PENDING

Japan PENDING

Mexico PENDING

Philippines PENDING

Serbia PENDING

Singapore PENDING

South Africa PENDING

US NL5-A9530M1 Model: A9530V1, A9530V3

This product is approved for sale in many countries.
Please contact Emerson for a complete listing.

THIS DRAWING IS PROPERTY OF AND PROPRIETARY TOEMERSON. THISDRAWING AND
THE INFO RMATION CON T AINED HEREIN S HALL NOT BE REPRODUCED NOR DISCLOSED TO
ANYONE EXCE PT THOSE REQUIR ING ITS USE FOR EMERSON AUTHORIZED PURPOSES.
THIS DOCUMENT SHALL BE DESTROYED OR RETURNEDTO EMERSON WHENNO LONGER
REQUIRED F OR THOSE PURPOSES.

AMS Model A9530 Wireless Vibration Monitor:
Power Options:
Battery must be replaced only with Tadiran Part Number: TL-4920/VE
or Emerson Part Number: A0702PPU

NOTE: Approved battery may be replaced in approved hazardous
locations per this drawing.

CSA-C/US CSA20CA80026524

Class I Division 1 Groups A,B,C & D
Class I Zone 0 AEx / Ex ia IIC T4 Ga

-40°C

< Ta < 85°C;

Type 4X Enclosure

ATEX CSANe 20ATEX2042X

2813 II 1 G Ex ia IIC T4 Ga (135°C)

-40°C

< Ta < 85°C

IECEx CSA 20.0002X

Ex ia IIC T4 Ga
Ta: -40°C to +85°C

Warnings:

1. Care should be taken to protect this device from impact or
abrasion i f located in a zone 0 environment.

2. Substitution of components may impair intrinsic safety.

3. The battery may present a potential electrostatic ignition
hazard. Use Caution when replacing the battery

Avertissements:

1. Des précautions doivent être prises pour le protéger des
chocs ou de l'abrasion s'il est situé dans un environnement de
zone 0.

2. La substitution de composants peut compromettre la sécurité
intrinsèque.

3. La batterie peut présenter un risque potentiel d'allumage
électrostatique. Soyez prudent lors du remplacement de la
batterie.

161047

.

MATERIAL:

FINISH:

ARTWORK FILEN AME/REVISION LEVEL:

Agency approved drawing. No changes

01 Initial Release 08-May-2020

without prior agency approval.

Conditions of Safe Use:

1. Shall be powered only by C-sized lithium primary cell type TL-4920/VE

manufactured by Tadiran or Emerson Part Number A0702PPU.

2. HART Terminal Entity parameters:
Uo = 5.84 V, Io = 116mA, Po = 329mW, Co = 0.1µF, Lo = 5mH;
Ui = 5.27 V, Ii = 5mA, Pi = 6.6mW, Ci = 13µF, Li = 0.022mH

3. The device may be configured using the HART terminals only by 375, 475, or

TREX field communicators.

4. Under certain extreme circumstances, the non-metallic parts incorporated in

the enc l osure of this equipment may generate an ignition-capable level of
electrostatic discharge. Therefore, the equipment shall not be installed in a
location where the external conditions are conductive to the build-up of
electrostatic charge on such surfaces. In addition, the equipment shall only be
cleaned with a damp cloth.

5. The device shall be installed on an earthed metal frame.

Conditions d'utilisation sûre:

1. Ne doit être alimenté que par une cellule primaire au lithium de taille C de type

TL-4920 / VE fabriquée par Tadiran ou Emerson Part Number A0702PPU.

2. Paramètres de l'entité du terminal HART:

Uo=5,84V,Io=116mA,Po=329mW,Co=0,1µF,Lo=5mH;

Ui=5,27V,Ii=5mA,Pi=6,6mW,Ci=13µF,Li=0,022mH

3. L'appareil ne peut être configuré à l'aide des terminaux HART que par des

communicateurs de terrain 375, 475 ou TREX.

4. Dans certaines circonstances extrêmes, les pièces non métalliques

incorporées dans le boîtier de cet équipement peuvent générer un niveau de
décharge électrostatique capable d'allumage. Par conséquent, l'équipement ne
doit pas être installé dans un endroit où les conditions externes conduisent à
l'accumulation de charges électrostatiques sur de telles surfaces. De plus,
l'équipement ne doit être nettoyé qu'avec un chiffon humide.

5. L'appareil doit être installé sur un cadre métallique mis à la terre.

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES

TOLERANCES

DECIMALS: .X ± .030

FRACTIONS: ± 1/32

.XX ± .020

.XXX ± .010

± 0°-30'ANGULAR:

32

FINISH:

DO NOTSCALE THIS DRAWING

For Refe rence Only

J. Clemons 08-Oc t-2019

DRAWNBY:

J. Clemons 08-Oc t-2019

LASTREVISED BY:

J. Clemons 08-Ma y-2020

RESP.ENGINEER

J. Baldwin

MANUFACTURING ENG.

T. Rogers

DATEDESIGNED BY:

DATE

DATE

DATE

DATE

DATEDOCUMENTCONTROL

TITLE

A9530 CSA, IECEx,

ATEX Installation Instructions

CAD FILENAME

D25902

FIRST USEDMODELNO.

9530

DRAWINGNO./PARTNO. SCALE

D25902

DATEECO NO.REV

Knoxville, TN.

SHEET

OF

1

1

CAUTION

Changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.

ISED approvals

This device contains licence-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including
interference that may cause undesired operation
of the device.

Cet appareil contient des émetteurs / récepteurs exemptés
de licence qui sont conformes aux RSS exempts de licence
d’Innovation, Sciences et Développement économique Canada.
Son fonctionnement est soumis aux deux conditions suivantes:

1. Cet appareil ne doit pas provoquer d’interférences.

2. Cet appareil doit accepter toute interférence,
y compris les interférences pouvant entraîner un
fonctionnement indésirable de l’appareil.