AMS Manual: PR 9350 / K 20 315, Linear Displacement Transducer Operation Manual | Asset Optimization Manuals & Guides

Machinery Health™ Sensor

PR 9350 / K 20 315, Linear Displacement Transducer

Operation Manual

MHM-97864

NC: 6110-00125

04.06.2014
Rev.: 1.007

Product Service Centers

America

Emerson Process Management
835 Innovation Drive
Knoxville, TN 37932
Tel: [phone]
Fax: [phone]

Incoming goods inspection

Check the content of the shipment to ensure that it is
complete; visibly inspect the goods to determine if the
device may possibly have been damaged during
transport. The following parts are included in the scope
of delivery and must be contained in the shipment.

1. PR 9350/.. or K 20315/.. with accessories accord
ing to the list “Included accessories” in chapter 6
of this manual.

Brazil

Emerson Process Management Ltd.
Av Hollingsworth 325
Sorocaba, SP
BRAZIL 18087-000
Phone: [phone]
Fax: [phone]

Europe, Middle East, Africa

Emerson Process Management
div. EASD
MHM Repair Center
Piestanska 1202/44
915 28 Nove Mesto nad Vahom
Slovakia
Tel: [phone]
Fax: [phone]

2. This operation manual

If the contents are incomplete, or if any defects are
observed, a complaint must be filed with the carrier
immediately. Moreover, the responsible Emerson sales
organization must be informed to enable repair or
replacement of the device. Repairs or calibration that
may be required, are only possible at the Emerson
factory.

In this case, a non-detachable tag with customer name
and defect observed must be attached to the device.

Repair and maintenance

During operation, monitors do not require any main
tenance.

Repair or calibration of monitors is only possible at
Emerson.

Asia

Emerson Process Management /
Asia Pacific Private Ltd.

3904 Room Central Plaza
18 Harbour Road Wan-Chai
Hong Kong
Tel: [phone]
Fax: [phone]

If work with the opened device on-site is
unavoidable, this should only be performed by a
specialist who is familiar with the associated
hazards.

DANGER

Capacitors in the device can still be energized, even
if the device has been disconnected from all power
sources.

If repair or recalibration of a sensor is required, it must
be sent to Emerson. Attach a non-detachable tag to
the monitor with customer name and defect
observed.

Guidelines for Returning Equipment to the Product
Service Center

If repair or calibration of a sensor is required, it must
be sent to Emerson.
Occasionally, concerns with CSI technology hardware
could arise. Should this happen, customers under war
ranty or a current support agreement are entitled to
no-charge repairs.

Follow the checklist below to minimize return time
and ensure proper processing of your equipment. Be
fore returning any equipment to a Product Support
Center, please review this information:

1. Obtain a Return Materials Authorization (RMA)
number and the address of the appropriate
Product Service Center by calling 865.675.4274*.

• Description of the hardware

problem

• Return shipping address including a

phone number (No P.O. boxes).

• Any special request regarding the

return shipment.

• A list of the model numbers of each

item(s) being returned, along with
the serial number.

• Your name, address, telephone

number and email address.

• Company Name.

A form for completing this information has
been provided.

Make a copy of the form, complete all lines,
and return a copy in each return shipment.

Listen to the options for receiving an RMA. You will
be routed to support personnel who will
document your concern and give you an RMA
number if you are under support or warranty. If
your hardware is not under support or warranty,
you must have a Purchase Order for the amount of
the repair service before you can receive an RMA
number. Pricing for your repair can be obtained
from support personnel or by calling your local
sales representative. Once you have your purchase
order, call 865.675.4274* for an RMA.

2. Once you have received your RMA, send your
hardware to the appropriate product service
centre. Your hardware package should include:

• RMA Number (plus Purchase Order if

applicable)

Out of warranty? Need to get under support?
Get a customized quote for bringing all your
CSI technologies under a support agreement:

Phone: [phone]*, ext. 2130
Fax: [phone]*
Email:
mhm.supportagreement@emersonprocess.
com

*Customers outside the Americas and
Canada: please refer to the list of service cen
ters and contact the service center near you.

All rights are strictly reserved

Reproduction or divulgation in any form
whatsoever is not permitted without written
authority from the copyright owner.

RMA Required Information

Company Name:

RMA number issued by Product
Service Center:

For all items beingreturned, please
list Model / Serial Number:

Are you under warranty or a current
support agreement (circle one)?

Yes No

If you answered no, what is your pur
chase order number?

Contact Name:

Contact Address:

Contact Phone:

Contact Fax:

Contact Email:

Please describe the problem you are experiencing:

If we are to send the return shipment to someone other than the Contact
Name/Address above, please provide that address here, including Con
tact Name and Phone Number:

Are there any special instructions regarding the return?

Please provide invoice address (if a purchase order was required):

Support customers - your instrument is shipped back to you the same way
that it is sent to our service center. For example, if you ship via ground
transportation, it is shipped back via ground.

Table of Contents

04.06.2014

Table of Contents

Chapter 1: General 1..................................

1.1 Hints for using this manual 1..................................

1.2 Symbol explanation 1.......................................

1.3 Liability and guarantee 2.....................................

1.4 Repair and maintenance 2....................................

1.5 Storage and transport 2.....................................

1.6 Disposal of the device 3......................................

1.7 Copyright information 3.....................................

Chapter 2: Safety Instructions 5........................

Operation Manual

NC: 6110-00125

2.1 Using the device 5..........................................

2.2 Radio interference suppression, EMC 5.........................

2.3 Owner's responsibility 6.....................................

2.4 Instructions on ESD safety 6..................................

Chapter 3: Application & Design 7......................

3.1 Application 7..............................................

3.2 Design 8..................................................

Chapter 4: Mounting & Installation 11....................

4.1 PR 9350 11.................................................

4.2 K 20 315 12.................................................

4.3 Connec tion of PR 9350 and K 20 315 13.........................

4.4 Commissioning 14...........................................

Chapter 5: Function check 15...........................

Chapter 6: Technical Data 17............................

Chapter 7: OM Revision List 21..........................

Chapter 8: Certificates 23..............................

iv Table of Contents

General

04.06.2014

Chapter 1: General

1.1 Hints for using this manual

This operating manual contains information on the correc t use of the sensor PR 9350 and the
set K 20 315.

For the correct and safe use of the device, this operating manual must be read completely
before starting the installation and operation. Particularly, all safety instructions of the
manual have to be taken into account.

The device may only be passed on to third parties by including the operating manual.

Operation Manual

NC: 6110-00125

NOTICE

At any correspondence regarding this device, please indicate type and serial-no. as shown
on the type plate.

1.2 Symbol explanation

NOTICE

This symbol marks passages that contain important information.

CAUTION

Notes, that may lead to malfunctions or faulty measurements without damaging the
device, are marked with this symbol. Without safety alert symbol, this symbol is used to
address practices not related to personal injury (ANSI Z 535.6).

DANGER

Safety and warning notes are marked with this symbol. Non-observance of such notes may
lead to damages to property or injuries to persons.

1 Hints for using this manual

Operation Manual

NC: 6110-00125

1.3 Liability and guarantee

Emerson is not liable for damages which were caused by improper use. The proper use also
includes knowledge and attention of this operating manual.

Changes at the device, that are not permitted particularly by Emerson, will lead to the loss of
the guarantee.

Due to continuous research and product development, Emerson reserves the right to change
the specification without notice.

1.4 Repair and maintenance

General

04.06.2014

During operation, the sensor PR 9350 as well as the set K 20 315 do not require any mainten
ance.

If work with the opened device on site is unavoidable, this should only be performed by a
specialist who is familiar with the associated hazards.

If repair or calibration of a PR 9350 or K 20 315 is required, it must be sent to Emerson. Attach
a non-detachable tag bearing customer name and defect observed to the sensor respectively
set. Refer to product service centers in the beginning of this manual for the address.

1.5 Storage and transport

The devices may only be stored or forwarded in their original packing or by using an equival
ent packing. The environmental conditions for storage and transport are specified in the
technical data (section “Technical Data).

Liability and guarantee 2

General

04.06.2014

1.6 Disposal of the device

Provided that no repurchase– or disposal agreement does exist, the properly dismantled
components has to be brought to re-utilization:

• Scrap metallic material remnants.

• Take plastic elements to plastic recycling facilities.

• Sort the remaining components for disposal, based on their material condition.

At this, the national provisions on waste disposal and protection of the environment shall
apply.

NOTICE

Environmental hazards!
Electrical waste and electronic components are subject to treatment as special waste

and may only be disposed by approved specialized companies.

Operation Manual

NC: 6110-00125

1.7 Copyright information

E epro GmbH

Jöbkesweg 3

D‐48599 Gronau

Germany

Phone: [phone]‐0Fax: [phone]‐256email: [e-mail]

All rights reserved.

Reproduction or digital use in any form and duplication are not permitted without written authority

from epro GmbH part of Emerson Process Management.

Published by epro GmbH part of Emerson Process Management.

Printed in Germany.

3 Disposal of the device

Operation Manual

NC: 6110-00125

General

04.06.2014

Copyright information 4

Safety Instructions

04.06.2014

Chapter 2: Safety Instructions

The device has left the factory in a faultless condition in regards to safety regulations. To
preserve this condition and to ensure a safe operation, all instructions in this manual must be
observed carefully.

The correct and safe use of this device requires, that operating and service personnel is familiar
with generally valid safety guidelines, complies with them and observes the special safety
comments, listed in this manual. Where necessary, safety sensitive points on the device are
marked.

DANGER

Since the sensor is an electrical equipment, commissioning and service may only be made
by trained personnel. Maintenance may only be carried out by trained, specialized and
experienced personnel.

Operation Manual

NC: 6110-00125

2.1 Using the device

The linear displacement transducer PR 9350 as well as the set K 20 315 are designed for meas
urement of static and dynamic displacements. The sensor should only be used for measure
ment purposes.

2.2 Radio interference suppression, EMC

The device is carefully shielded and tested to be technically immune to radio interference and
complies with current standards. When operating together with other peripheral devices, that
are not properly shielded against radio interference, disturbances and radio interferences may
occur.

5 Using the device