Amprobe VPC-20 User Manual
Digital Voltage and Continuity Tester
Function
Range
Accuracy(%rdg.+digit s)
V AC(50Hz~400Hz)
600V
+(2.9%+8)
V DC
600V
+(1.5%+2)
Continuity te st: Audi ble threshold 0~10KΩ,Continuity beeper 2KHz.
Overl oad protection: AC/DC 600V
Diminsions/wt.:215x96.3x37.5mm/312g
Model VPC-20
Instruction Manual
m Safety Information
• Never use the tester if it or test leads appear damaged.
• Never apply more than 600V DC or 600V AC rms. between any terminal and
earth ground
• When using the probes, keep your fingers behind the finger guard on
the probes.
• Turn off power to the circuit under test before cutting, desoldering, or
breaking the circuit. Small amounts of current can be dangerous.
• Use caution when working with voltage above 60V dc or 30V ac rms. Such
voltages pose a shock hazard.
Automatic Operation
The tester automatically turns on when you short the two test probes or place the
probes across a complete circuit.When turned on, the tester powers up in continuity
mode. If a dc or ac voltage greater than about 4.0V is present across the inputs, the
tester switches to dc or ac voltage mode.The tester automatically shuts down after
approx. 4 minutes of inactivity.
Specifications:
12V DC
240V AC
Continuity testing
Turn off circuit power before testing. Beeper indicates shorts lasting 1 ms or longer.
Measuring Voltage
Refer to Automatic Selection
DC Voltage (Volts dc>4.0V)
600V dc maximum
AC Voltage (Volts dc>4.0V)
600V ac maximum
50Hz to 400Hz
SHORT 10KΩ OPEN
Display: Large 1999 count LCD display with function and high voltage warning indication.
Maximum Voltage Between any Terminal and Earth Ground: 600V dc; 600V ac rms,
Over-voltage Category III 600V
Safety: Complies with EN61010-1:1993 for use in over-voltage CAT III environments
Pollution Degree: 2
For indoor use only
EMC Regulations: EN50081-1, EN50082-1
Polarity: Automatic, (-)negative polarity indication.
Over-range: “1” mark indication
Low battery indication: The “BAT” is displayed when the battery voltage drops below
the operating level
Measurement rate: 2 times per second, nominal
Continuity test: Audible threshold 0-10KW, Continuity beeper 2KHz
Input Impedance: 400KΩ
Temperature: 5 °C(41°F) to 40°C (104°F)
Altitude: Operating: 2000m; Storage: 10,000m
Relative Humidity: 80% for Temp up to 31C decreasing linearly to 50 % RH at 40C
Pollution Degree: 2
For indoor use only
Battery Type: AA (2) NEDA 15F or IEC R6
Replacing the Batteries
If the sign “BAT” appears on the LCD display, it indicates that the batteries should be
replaced. Remove screws on the back cover and open the case. Replace the exhausted batteries with new batteries. (AA(2);NEDA 15F or IEC R6)
2xAA
Disconnect probes from
Voltag. Do not over-tighten
screws
WARRANTY
Congratulations! Your new instrument has been quality crafted according to quality
standards and contains quality components and workmanship. It has been inspected
for proper operation of all of its functions and tested by qualified factory technicians
according to the long-established standards of our company.
Your instrument has a limited warranty against defective materials and/or workmanship
for one-year from the date of purchase provided that, in the opinion of the factory, the
instrument has not been tampered with or taken apart.
Should your instrument fail due to defective materials, and/or workmanship during this
one-year period, a no charge repair or replacement will be made to the original purchaser. Please have your dated bill of sale, which must identify the instrument model
number and serial number and call the number listed below:
Repair Department
ATP – Amprobe, TIF, Promax
Miramar, FL
Phone: 954-499-5400
800-327-5060
Fax : 954-499-5454
Website: www.amprobe.com
Please obtain an RMA number before returning product for repair. Outside the U.S.A.
the local representative will assist you. Above limited warranty covers repair and
replacement of instrument only and no other obligation is stated or implied.
Miramara, Florida 33025
ATP VPC-20Manual printed in China
P/N:
el: 954-499-5400
T
oll Free: 800-327-5060 Fax: 954-499-5418
T
Loading...