I
K500
Mobile Computing Device
User's Manual
Version 2.0
2019.01
- II -
This page is intentionally left blank.
- i -
Revision History
Version
Release Time
Description
1.0
November 2018
Initial release
2.0
Jan 2019
Update CE/FCC warning
- ii -
Copyright
Copyright © 2018 AMobile Intelligent Corp. All Rights Reserved.
This document contains proprietary information protected by copyright. No part of
this manual may be reproduced by any mechanical, electronic, or other means in any
form without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior notice in order
to improve the reliability, design and function. It does not represent a commitment
on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect,
special, incidental, or consequential damages arising from the use or inability to use
the product or documentation, even if advised of the possibility of such damages.
About This Manual
This user’s manual provides the general information and installation instructions for
the product. The manual is meant for the experienced users and integrators with
hardware knowledge of personal computers. If you are not sure about any
description in this manual, consult your vendor before further handling.
We recommend that you keep one copy of this manual for the quick reference for
any necessary maintenance in the future. Thank you for choosing AMobile products.
- iii -
Contents
Contents
Preface ...................................................................................................................v
Declaration of Conformity ............................................................................................... v
CE ............................................................................................................................ v
FCC Class B .............................................................................................................. v
RoHS ....................................................................................................................... vi
SVHC / REACH ........................................................................................................ vi
Safety Symbols ............................................................................................................... vii
Important Safety Instructions ........................................................................................ vii
Laser Safety ..................................................................................................................... ix
Rechargeable Battery Pack Safety .................................................................................. ix
General Cleaning Tips ..................................................................................................... xi
Cleaning Tools ...................................................................................................................... xi
Recommended Cleaning Procedures .................................................................... xii
Disposing of the Device ................................................................................................. xii
Additional Information & Technical Support .................................................................. xiii
Warranty ........................................................................................................................ xiii
Chapter 1 Introduction ......................................................................................... 1
1.1
Product Highlights ..................................................................................................... 2
1.2
Package Contents ...................................................................................................... 3
1.3
Parts of the Device .................................................................................................... 4
1.4
Dimensions ................................................................................................................ 5
1.5
Specifications ............................................................................................................ 6
Chapter 2 Getting Started .................................................................................... 9
2.1
Installing microSD and SIM Card ............................................................................. 10
2.2
Charging the Battery ............................................................................................... 11
2.2.1
Charging the Battery ................................................................................... 11
2.2.2
Checking the Battery Level .......................................................................... 11
2.3
Installing/Replacing the Battery .............................................................................. 12
2.4
Optimizing Battery Life ............................................................................................ 13
Chapter 3 Using the Rugged Handheld Deivce .................................................... 15
3.1
Using Touch Screen.................................................................................................. 16
3.1.1
Basic Operations ......................................................................................... 16
3.1.2
Text Input .................................................................................................... 17
- iv -
Contents
3.1.3
Sleep Mode ................................................................................................ 17
3.2
Home Screen .......................................................................................................... 18
3.2.1
Using the Quick Settings Panel ................................................................... 20
3.2.2
Extending Home Screen ............................................................................. 20
3.3
Using Cellular Network ........................................................................................... 21
3.3.1
Making/Receiving Calls ............................................................................... 22
3.3.2
Data Connection ......................................................................................... 22
3.3.3
Data Roaming ............................................................................................. 23
3.3.4
Limiting Mobile Data Connection to 2G ..................................................... 23
3.4
Using the Wi-Fi Feature .......................................................................................... 23
3.4.1
Enabling Wi-Fi and Connecting to a WLAN ................................................. 24
3.4.2
Adding a Wi-Fi Network .............................................................................. 25
3.4.3
Connecting to a Wi-Fi Network by WPS ..................................................... 26
3.4.4
Forgetting/Modifying a Wi-Fi Network ...................................................... 28
3.4.5
Making Your Device a Wi-Fi Hotspot .......................................................... 28
3.5
Using the Bluetooth Feature .................................................................................. 29
3.5.1
Enabling Bluetooth and Pairing with Bluetooth Device .............................. 30
3.5.2
Configuring Bluetooth Features to Use ...................................................... 31
3.5.3
Disconnect from a Bluetooth Device .......................................................... 32
3.5.4
Making Your Bluetooth Device Discoverable .............................................. 32
3.5.5
Additional Bluetooth Settings ..................................................................... 33
3.6
Using the Location Feature..................................................................................... 34
3.6.1
Enabling/Disabling Location Service ........................................................... 34
3.6.2
Location Mode ........................................................................................... 34
3.7
Using Camera ......................................................................................................... 35
3.8
Using the NFC Feature ............................................................................................ 37
3.8.1
Enabling/Disabling NFC .............................................................................. 37
3.8.2
Configuring NFC Modes .............................................................................. 37
3.8.3
Exchanging Data with NFC-Enabled Device ................................................ 38
3.9
Using the Barcode Scanner..................................................................................... 39
3.9.1
Installing APK File........................................................................................ 39
3.9.2
Scanning the Barcode ................................................................................. 40
3.9.3
Supported Barcode Formats ...................................................................... 41
- v -
Preface
Preface
Declaration of Conformity
CE
Trade Mark: Amobile
Model number: K500
Operating Temperature: ‐10° C to 40° C
This device was tested for typical body‐worn operations. To comply with RF
exposure
requirements, a minimum separation distance of 0cm must be maintained
between the user’s
body and the handset, including the antenna. Third‐party belt‐clips, holsters, and
similar
accessories used by this device should not contain any metallic components.
Body‐worn
accessories that do not meet these requirements may not comply with RF
exposure
requirements and should be avoided. Use only the supplied or an approved
antenna.
This device in compliance with the essential requirements and other relevant
provisions of
Directive 2014/53/EU. All essential radio test suites have been carried out.
1. CAUTION : RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSE OF
USED BATTERIES ACCORDING TO THE INSTRUCTIONS
2. The device complies with RF specifications when the device used at 5cm form
your body
FCC Class B
This device complies with part 15 of the FCC Rules. Operation is subject to the
- vi -
condition that this device does not cause harmful interference
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information:
This Mobile Phone meets the government's requirements for exposure to radio
waves. The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough evaluation of
scientific studies. The standards include a substantial safety margin designed to
assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6
W/kg averaged over one gram of tissue. Device types: S100 (FCC ID: RGF-S0816)
has also been tested against this SAR limit.This device was tested for typical bodyworn operations with the back of the handset kept 0mm from the body. To
- vii -
maintain compliance with FCC RF exposure requirements, use accessories that
maintain a 10mm separation distance between the user's body and the back of
the handset. The use of belt clips, holsters and similar accessories should not
contain metallic components in its assembly. The use of accessories that do not
satisfy these requirements may not comply with FCC RF exposure requirements,
and should be avoided.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 10mm must be
maintained between the user’s body and the handset, including the antenna.
Third-party belt-clips, holsters, and similar accessories used by this device should
not contain any metallic components. Body-worn accessories that do not meet
these requirements may not comply with RF exposure requirements and should
be avoided. Use only the supplied or an approved antenna.
- vi -
Preface
RoHS
AMobile Intelligent Corporation certifies that all components in its products are
in compliance and conform to the European Union’s Restriction of Use of
Hazardous Substances in Electrical and Electronic Device (RoHS) Directive
2002/95/EC.
The above mentioned directive was published on 2/13/2003. The main purpose of the
directive is to prohibit the use of lead, mercury, cadmium, hexavalent chromium,
polybrominated biphenyls (PBB), and polybrominated diphenyl ethers (PBDE) in
electrical and electronic products. Member states of the EU are to enforce by
7/1/2006.
AMobile Intelligent Corporation hereby states that the listed products do not contain
unintentional additions of lead, mercury, hex chrome, PBB or PBDB that exceed a
maximum concentration value of 0.1% by weight or for cadmium exceed 0.01% by
weight, per homogenous material. Homogenous material
is defined as a substance or mixture of substances with uniform composition (such
as solders, resins, plating, etc.). Lead-free solder is used for all terminations (Sn(96-
96.5%), Ag(3.0-3.5%) and Cu(0.5%)).
SVHC / REACH
To minimize the environmental impact and take more responsibility to the earth we
live, AMobile hereby confirms all products comply with the restriction of SVHC
(Substances of Very High Concern) in (EC) 1907/2006 (REACH
--Registration, Evaluation, Authorization, and Restriction of Chemicals) regulated by
the European Union.
All substances listed in SVHC < 0.1 % by weight (1000 ppm)
- vii -
Preface
Safety Symbols
This symbol indicates that a potential hazard to personal safety exists from a
laser source. When this symbol is displayed in this manual, pay special attention
Important Safety Instructions
Read these safety instructions carefully:
1.
Read all cautions and warnings on the device.
2.
Dropping it or letting it fall may cause damage
3.
Make sure the correct voltage is connected to the device.
4.
For pluggable device, the socket outlet should be near the device and should be
easily accessible.
5.
Disconnect this device from the A/C outlet before cleaning it. Use a moist
cloth. Do not use liquid or sprayed detergent for cleaning.
6.
Do not scratch or rub the screen with a hard object.
7.
Never use any of the solvents, such as Thinner Spray-type cleaner, Wax,
Benzene, Abrasive cleaner, Acid or Alkaline solvent, on the display. Harsh
chemicals may cause damage to the cabinet and the touch sensor.
- viii -
Preface
8.
Remove dirt with a lightly moistened cloth and a mild solvent detergent.
Then wipe the cabinet with a soft dry cloth.
9.
If the device will not be used for a long time, disconnect it from the power
source to avoid damage by transient overvoltage.
10.
Never pour any liquid into openings. This may cause electrical shock.
11.
Never open the device. For safety reasons, the device should be opened only
by qualified service personnel.
12.
If one of the following situations arises, get the device checked by service
personnel:
a.
The power cord or plug is damaged.
b.
Liquid has penetrated into the device.
c.
The device does not work well, or you cannot get it to work
according to the user’s manual.
d.
The device has been damaged.
e.
The device has obvious signs of breakage.
13.
Keep this User’s Manual for later reference.
14.
Do not leave this device in an uncontrolled environment where the storage
temperature is below
-20° c (-4° f) or above 70° c (158° f). This may damage the device.
- ix -
Preface
Do not use the power adapter that isn’t made for the device. Supplying the
device with inappropriate voltage may cause harm to the battery or, even
worse, burn the device.
To prevent possible hearing damage, do not listen at high volume levels for
long periods.
Laser Safety
The device's barcode scanner that uses laser lights is a class 2 laser product. DO NOT
stare into the laser beams or point the laser beam at anyone's eyes when the
barcode scanner is in operation.
Rechargeable Battery Pack Safety
With very little care, you can optimize the battery life and maximize the lifespan of
the battery. Most importantly, use only the device in its ideal operating temperature
(as described in 1.5 Specifications) – do not leave it in a hot trunk during the summer.
• Important Terms to Understand
“Battery life” means the time the device will run before it must be recharged
(sometimes this is also called “playtime” or “runtime”).
“Battery lifespan” means the total amount of time your battery will last before it
must be replaced.
• Using the Device for the First Time
Be sure to fully charge (approx. 3 hours) the device when charging the device for
the first time.
• Long-Term Storage & Maintenance
If you are putting away the battery for more than three months, it is
recommended that the battery should be stored separately and fully charged,
LASER RADIATION
- xii -
Preface
and get recharged every three months. If you store an uncharged battery, it could
fall into a deep worn-out state which would render it incapable of holding any
charge. Be sure to store the equipment and battery at the proper temperature
(as described in 1.5 Specifications).
• Battery Lifespan
The non-replaceable batteries for the device are designed to retain up to 80% of
their original capacity after 300 charging and recharging cycles when properly
maintained. You may choose to replace new battery with the help of qualified
service personnel when it no longer holds the sufficient charge that meets your
needs.
• The lithium-ion battery is currently one of the most popular battery packs. The
best advantage is that it has no memory effect, so users needn’t worry about that
issue. Users can charge the battery anytime whether it is fully drained or not.
However, it’s recommended that users drain the battery until the system shows
power shortage warning and then recharge the battery. Doing so is helpful to the
reliability of your battery.
• Don’t use the battery pack as a power supply for other equipment.
• Don’t expose the battery to elevated heat situations such as under direct
sunlight in a car or near fire.
• Don’t disassemble the battery, or the battery leakage might cause skin or eye
injury. If electrolyte leaking from the battery contacts your skin or clothing,
immediately flush it with running water. If it splashes into eye, rinse the eye at
least 15 minutes with clean water and then seek medical attention.
• To avoid battery leakage or explosion, don’t discard the battery into water or
fire, or put them near a heat source such as a gas stove or an oven.
• If you are putting away the battery for more than three months, it is
recommended that the battery should be fully charged, and get recharged every
three months. If you store the device with an uncharged battery, it could fall into a
deep worn-out state which would render it incapable of holding any charge. Be
sure to store your the device and battery at the proper temperature (as described
in 1.5 Specifications).
• Use the appropriate container to store the battery such as a paper box. Do not
allow a metal object to touch the terminal of the battery.
• The battery consists of precise electrical components and cells. Do not drop
or hit the battery.
- xii -
Preface
General Cleaning Tips
You may need the following precautions before you begin to clean the device. When
you clean any single part or component for the device, please thoroughly read and
understand the details below.
1.
We strongly recommended that you should shut down the system before you
start to clean.
2.
When you need to clean the device, please rub it with a piece of dry cloth.
3.
Never drop the components inside the device or get circuit board damp or wet.
4.
Be cautious of all kinds of cleaning solvents or chemicals when you use it
for the sake of cleaning. Some individuals may be allergic to the ingredients.
5.
Try not to put any food, drink or cigarette around the device.
Cleaning Tools
Although many companies have created products to help improve the process of
cleaning your devices and peripherals, users can also use household items to clean
their devices and peripherals. Below is a listing of items you may need or want to use
while cleaning your devices or peripherals. Keep in mind that some components in
your device may only be able to be cleaned using a product designed for cleaning
that component, if this is the case it will be mentioned in the cleaning.
•
Cloth: A piece of cloth is the best tool to use when rubbing up a component.
Although paper towels or tissues can be used on most hardware as well, we
still recommend you to rub it with a piece of cloth.
•
Water or rubbing alcohol: You may moisten a piece of cloth a bit with some
water or rubbing alcohol and rub it on the device. Unknown solvents may
be harmful to the plastics parts.
•
Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are
excellent tools for wiping hard to reach areas in your keyboard, mouse, and
other locations.
•
Foam swabs: Whenever possible, it is better to use lint-free swabs such as
foam swabs.
- xii -
Preface
Recommended Cleaning Procedures
1.
Close all application programs
2.
Close operating software
3.
Turn off the device
4.
Remove all peripherals
5.
Disconnect the power cable
6.
Proceed to clean.
Disposing of the Device
• Within the European Union
EU-wide legislation, as implemented in each Member State,
requires that waste electrical and electronic products carrying the
mark (left) must be disposed of separately from normal household
waste.
This includes monitors and electrical accessories, such as signal cables or power
cords. When you need to dispose of your display products, please follow the
guidance of your local authority, or ask the shop where you purchased the
product, or if applicable, follow any agreements made between yourself. The
mark on electrical and electronic products only applies to the current European
Union Member States.
• Outside the European Union
If you wish to dispose of used electrical and electronic products outside the
European Union, please contact your local authority so as to comply with the
correct disposal method.
- xiii -
Preface
Additional Information & Technical Support
You can download the related technical documents such as datasheet and user’s
manual as well as driver on our website.
Please do not hesitate to call or e-mail our customer service when you still
cannot get the information you need.
http://amobile-solutions.com/web_en/contact.php
E-mail: support@amobile.com.tw
Warranty
This product is warranted to be in good working order during the warranty period.
Should this product fail to be in good working order at any time during this period,
we will, at our option, replace or repair it at no additional charge except as set forth
in the following terms. This warranty does not apply to products damaged by misuse,
modifications, accident or disaster.
Vendor assumes no liability for any damages, lost profits, lost savings or any other
incidental or consequential damage resulting from the use, misuse of, or inability to
use this product. Vendor will not be liable for any claim made by any other related
party.
Vendors disclaim all other warranties, either expressed or implied, including but not
limited to implied warranties of merchantability and fitness for a particular purpose,
with respect to the hardware, the accompanying product’s manual(s) and written
materials, and any accompanying hardware. This limited warranty gives you specific
legal rights.
Return authorization must be obtained from the vendor before returned
merchandise will be accepted. Authorization can be obtained by calling or faxing the
vendor and requesting a Return Merchandise Authorization (RMA) number. Returned
goods should always be accompanied by a clear problem description.
- xiv -
This page is intentionally left blank.
- 1 -
Chapter11
Introduction
- 2 -
Introduction
1.1 Product Highlights
• Fully rugged for warehousing / transportation /
manufacturing / retail applications
• IP-65 certified, 1.5M (5ft.) drop resistance
• 4” TFT color LCD 800 x 480 HD resolution
• Projected capacitive multi-touch panel with anti-reflection
Corning
®
glass
• High mobility with multiple connectivities including WLAN,
Bluetooth and WWAN
• Optional built-in barcode imager
• With optimized battery life up to 8 hours
• G-sensor, gyroscope, light sensor, E-compass, Proximity Sensor, GPS
navigation
• Fingerprint authentication for security protection
• 29Key ,38Key ,47Key ,by Customer Optiona
- 3 -
Introduction
1.2 Package Contents
Upon opening the package, carefully inspect the contents. If any of the items is
missing or appears damaged, contact your local dealer or distributor. The package
should contain the following items:
4” Rugged Android™ Mobile Computing Device
USB Cable
Pogo pin to Type C Adapter
Charger
User Manual
- 4 -
Introduction
1.3 Parts of the Device
1
Barcode Scanner
5
Fingerprint
2
Barcode Trigger Key
6
Speaker
3
Power Key
7
NFC
4
Camera
8
Battery
6
1 3 2 4 2 5 7
8
- 5 -
Introduction
1.4 Dimension
- 6 -
Introduction
1.5 Specifications
Durability Features
IP-65 certified
1.5M (5ft.) drop-resistance
System
CPU
octa-core Qualcomm Snapdragon 450 8* Cortex A53, 1.8 GHz 1.5GHz
OS
Android™ 8.1
Memory
2GB
Storage
16GB
Audio
Integrated microphone
Integrated speaker
Peripherals and Devices
Camera
Front: N/A
Rear: 8.0 megapixel AF camera with LED
Sensor
Accelerometer (G-sensor)
3-axis digital gyroscope
E-Compass/Proximity Sensor
Light Sensor
Ambient light sensor
WLAN
Integrated IEEE 802.11 a/b/g/n /ac/r
Bluetooth
Integrated Bluetooth 4.2 LE with HID input
WWAN
Support, details refer to datasheet
Navigation
GPS, Glonass, Beidou
Barcode Scanner
1D/2D barcode reader with physical trigger buttons
I/O Interface
USB Port
1x Nano+ T Card (up to 128GB)
SD Slot
1 x microSD card slot (up to 128GB)
- 7 -
Introduction
LCD Display
Size/Type
4” TFT LCD
Resolution
800 x 480
Touch Screen
Type
5-point Projected Capacitive Touch screen
Glass coating w/ anti-reflection coating
Power Supply
Power System
Lithium-ion battery
Lithium-ion rechargeable battery
Battery Type
Replaceable
Battery Capacity
5200mAh
Battery Life
Up to 8 hours battery life
Adapter Input
Input: AC100~240C, 50~60 Hz
Adapter Output
DC power output: 12V/2A
Mechanical & Environmental
Operating Temp.
-15 ~ 55°C (5°F ~ 131°F )
Storage Temp.
-20 ~ 70°C (-4°F ~ 158°F )
Dimensions
(W x H x D)
202.4 x 77.8 x 41.6 mm (7.97” x 3.06”x 1.64”)
Weight
422g (0.93lb) (with battery)
- 8 -
This page is intentionally left blank.
- 9 -
Chapter22
Getting Started
- 10 -
Getting Started
2.1 Installing microSD and SIM Card
To install the microSD card and/or SIM card:
Figure 2-1 Press the two
buttons next to the battery.
Figure 2-2 Remove the
battery
Figure 2-3 Remove the
plastic cover.
Figure 2-4 As the diagram
shown, insert SIM Card
and TF Card.
- 11 -
Getting Started
2.2 Charging the Battery
Due to shipment, the battery is partially drained when the package is delivered to
you. Be sure to charge the battery to full when you are charging it for the first time.
Caution: Do not charge the K500 via computer USB connection due to that the
voltage output from computer USB is not enough to charge the device.
2.2.1 Charging the Battery
To charge the battery using a electrical outlet:
1.
Using the USB cable that comes with the device, connect the small end of the
cable to the USB port on the device.
2.
Then connect the other end of the USB cable to the power adapter.
3.
Connect the power adapter to an electrical outlet.
Warning: Use only the power adapter that comes with your device. Using a
different power adapter may damage your device and may result in poor
performance. It may also invalidate warranty applying to the device.
2.2.2 Checking the Battery Level
When the charging is in process, a battery indicator will appear in the status bar
showing the charging percentage. Unplug the USB cable from the device when the
battery is fully charged.
- 12 -
Getting Started
2.3 Installing/Replacing the Battery
In case you need to install or replace the battery, follow the steps below to
access the battery chamber and replace the battery.
1. Press the two buttons next to the battery.
2. Remove the battery
3. Place battery back to slot and press down
4. Finish the replacement
- 13 -
Getting Started
2.4 Optimizing Battery Life
To optimize the operating time of the battery, it is recommended that you do the
following:
• Decrease the LCD display brightness.
• Set a shorter timeout of inactivity to allow the screen enter sleep mode.
• Turn off the display if you are not using it.
• Always exit the applications if it is not in use.
• Disable the Wi-Fi, Bluetooth or GPS function if you are not using it.
• Disable the App that heavily drains the battery if you are not using it.
To view the battery usage by access settings-> Battery.
• Disconnect USB devices such as USB flash drive if it is not in use.
- 14 -
This page is intentionally left blank.
- 15 -
Chapter33
Using the Rugged
Mobile Computing
Device
- 16 -
Using the Mobile Computing Device
3.1 Using Touch Screen
The K500 comes with a projected capacitive multi-touch screen. Users are able to
manipulate icons, graphic buttons, menus, the onscreen keyboard or any onscreen
items with touch control. This chapter will walk you through the basic operations.
3.1.1 Basic Operations
The table below provides instructions on how to use the multi-touch screen:
Operation
Description
Tap
Tap an item and quickly release to select an item, launch an
application, or open a menu.
Tap and hold
Tap and hold an item or a blank area on the screen for a few
seconds until a menu opens or an option appears.
Drag
Tap and hold on an item, such as an image or an icon, then move it to
the target position. While dragging, do not release until you have
reached the target position.
Swipe
Move your finger horizontally or vertically across the screen to
scroll through the screen, App menu, pages, lists and so on.
Zoom in / out
Move two fingers closer together on an item, such as a picture, web
page, or map, to zoom out, or move two fingers apart to zoom in.
Double Tap
For some applications, quickly tap twice on an item to zoom in and
double-tap again to zoom out.
- 17 -
Using the Mobile Computing Device
3.1.2 Text Input
The K500 has a physical keyboard and also onscreen keyboard to receive user's text
input.
To open the onscreen keyboard, simply tap a text input field and the keyboard
appears.
3.1.3 Sleep Mode
When the device suspends to sleep mode, it enters a low power state and the
display is off to save the battery power. You can manually force the device to enter
sleep mode or specify a period of inactivity before it automatically enters sleep
mode. While the device is in sleep mode, it is still capable of receiving messages and
calls and processing tasks like downloading.
To switch to sleep mode, press the Power key until the screen is turned off.
To wake up the device from sleep mode, press the Power key until the screen is
turned on. If the screen is locked, swipe the lock icon to the outer circle to unlock the
device.
To specify the period of inactivity, swipe down the Status Bar in the upper right
corner and tap Settings | Display | Sleep. Then select a time of inactivity before the
device enters sleep mode.
- 18 -
Using the Mobile Computing Device
3.2 Home Screen
The Home screen provides you with an instant access to device status, notifications,
application shortcuts, folders and widgets. Simply tap an item and you can launch the
associated application. You can also add desired items to the Home screen, extend
the Home screen or personalize the wallpaper to tailor it to your personal needs.
When you power on the device for the first time, a typical Home screen looks like
the example below.
Status Bar
a Widget
App Launcher
Home screen
Back button
Home button
Recent App button
- 19 -
Using the Mobile Computing Device
The table below describes the elements on a typical Home screen:
Element
Descriptions
Notification
Area
The Notification Area is visible across the Home screens.
This area informs you of new messages, events, alarms, and activities
in progress. Applications you install on your device may show their
own icons or messages in the area.
You can access the notification panel to see more information by
swiping down the Notification Area.
Status Bar
The Status Bar is visible across the home screens. It shows the time,
signal strength, battery status, and other information.
Applications you install on your device may show their own icons
in this area.
You can swipe down the Status Bar to access a Quick Settings panel
where you can quickly access some most commonly used settings and
features.
Home Screen
•
Tap an item on this screen to launch that item.
•
To delete an icon or widget, tap and drag the item to the top of the
screen until the Remove bar appears on the top of the screen. Then
move the icon to the Remove bar.
•
Tap and hold any empty spot on this screen to customize your
home screen.
Widget
The miniature of an application that functions directly on the
Home screen.
App Launcher
Tap it to open the "App Launcher" where all applications installed
on the K500 can be viewed and launched.
Bottom Dock
The dock is visible across the home screens. It shows the most
commonly used App icons for quick access. You can change the icons
as needed.
Back Button
Tap to go to the previous screen.
Home Button
Tap to return to Home scree.
Recent App Button
Tap to view show your recent Apps and touch an App to reopen it. To
remove an App from the list, swipe it left or right.
- 20 -
Using the Mobile Computing Device
3.2.1 Using the Quick Settings Panel
Swiping down the Status Bar will bring up a Quick Settings panel where you can quickly
access some most commonly used settings and features. To enable/disable a feature or switch
between available options , simply tap the intended tile. It appears dimmed when disabled and
brightened when enabled.
For some features such as Wi-Fi, Bluetooth, Flashlight, Portriat, Airplane mode, you can also
tap and hold the tile to directly access the settings page.
3.2.2 Extending Home Screen
The Home screen is extended beyond the screen width to provide more space for
adding application shortcuts and widgets.
To access the extended Home screen, swipe on the Home screen to the up and down.
To add application icons or widgets to the extended Home screen:
1. Tap the App Launcher icon on the Home screen to locate the target
application icon or widget.
2. Tap and hold the target icon or widget until the extended Home Screen
appears.
3. Move the icon or widget to desired screen and then release.
Swipe down the Status Bar to
access the Quick Settings panel.
For some feature tiles, you can
•tap to enable/disable a feature
•tap and hold to quickly access its
settings page
- 21 -
Using the Mobile Computing Device
3.3 Using Cellular Network
After you insert the SIM card(s) to the K500 for the first time and power on the K500,
depending on your mobile network carrier you might be guided to activate the
account and connect to your mobile network. If you are asked for a PIN to unlock
the SIM card when powering on the K500, contact your cellular network carrier for
the default PIN.
When a new SIM card is detected by the K500, you will be prompted to configure its
usage, including voice call, messaging and data connection. You can configure it now or
change the settings later by accessing setting-> Network & Internet-> Mobile network.
Different locations may have different mobile networks available. The K500 adopts
the fastest mobile network available for data. However, in order to extend the
battery life, you can configure the K500 to use only a slower 2G network for data.
You can also configure the K500 to access a different set of networks entirely, or to
behave in special ways when roaming.
If there is no SIM card, the K500 isn't capable of 3G voice and data services; however it
is still able to connect to a Wi-Fi network to log into a wireless local area network. To
learn more, see 3.4 Using the Wi-Fi Feature.
- 22 -
Using the Mobile Computing Device
3.3.1 Making/Receiving Calls
After you activate your SIM card(s), the K500 auto-connects to your cellular network
when it powers on. You can start to use the phone service.
Using phone service, e.g., making or answering a call, is similar to the way you use a
mobile phone.
To use the device for phone service, it is suggested that you connect a wired headset
to the device's headset connector or use a wireless Blueooth headset or car kt. For
instructions on how to connect to a Bluetooth device, see 3.5 Using the Bluetooth
Feature for details.
3.3.2 Data Connection
Connecting to a cellular network enables you to use voice service as well as data
connection service, e.g., the Internet connection. However, in most cases using Wi-Fi
for data connection is faster and less expensive than using a cellular network and you
may want to disable data connection of your SIM card when Wi-Fi is available. On the
other hand, you may want to enable cellular data connection when Wi-Fi is not
available.
To enable or disable data connection:
1.
Swipe down the Status bar and tap
Mobile data.
2.
Enable data connection for SIM
card or tap Off to disable data
connection.
- 23 -
Using the Mobile Computing Device
3.3.3 Data Roaming
When the K500 moves to where your cellular network is not available, data roaming
connects the K500 to other service providers. This is often useful abroad if you want
to keep receiving data across networks. However, the mobile rates can substantially
increase as the costs for accessing the Internet are particularly high. Under such
situation you may want to disable the data roaming function of the SIM card.
To enable or disable data roaming:
Swipe down the Status bar and tap Settings | NETWORK & INTERNET
| Mobile network
While data roaming is disabled, you can still use Wi-Fi connection to access the
Internet data. See 3.4 Using the Wi-Fi Feature.for more information.
3.4 Using the Wi-Fi Feature
The K500 is capable of Wi-Fi networking. Wi-Fi is a wireless networking technology
that uses an access point, also known as the “hotspot”, to connect to an Internet
service provider over the wireless local area network (WLAN). Some hotspots are
open to connect while others request you to present a key to authenticate your
connection. The K500 needs to be configured including such key to connect to a
hotspot.
Follow the guide below to connect the K500 to your wireless local area network:
Note: Turn off Wi-Fi when it isn’t used to extend battery life.
The Status Bar displays the following icons that shows Wi-Fi status.
Icon
Description
?
Notifies that an open Wi-Fi network is in range.
Notifies that a Wi-Fi network is connected. Waves indicate signal
strength.
- 24 -
Using the Mobile Computing Device
3.4.1 Enabling Wi-Fi and Connecting to a WLAN
1.
Swipe down the Status bar and tap the WI-FI
tile to enable Wi-Fi if it isn't enabled yet.
2.
In the Quick Settings panel, tap and hold the
WI-FI tile to access the Wi-Fi settings page.
The K500 then proceeds to scan for available Wi-Fi
networks in range and displays the names of those
found. Secured networks are displayed with waves
denoting signal strength plus a lock on while
the open networks don't.
To re-scan for available Wi-Fi networks, tap the
menu
Off, and on
.
Tap a network to connect to it. To connect to a secured network, you’re
prompted to enter a password or other credentials. (Ask your network
administrator for details.)
If the K500 detects a network previously connected to, the K500 auto- connects to
it.
Once a Wi-Fi network is connected, it displays as “connected” on the Wi-Fi
settings screen. Tap it to see the details about the speed, security, address, and
related info.
- 25 -
Using the Mobile Computing Device
3.4.2 Adding a Wi-Fi Network
Under the following situations, you may need to manually add a Wi-Fi network:
•
When a Wi-Fi network doesn’t broadcast its name (SSID)
•
When a Wi-Fi network is out of range and you want the K500 to
remember it and auto-connect to it as soon as it gets in range.
To add a Wi-Fi network:
1.
Swipe down the Status bar and tap the WI-FI tile to enable Wi-Fi if it isn't
enabled yet.
2.
In the Quick Settings panel, tap and hold the WI-FI tile to access the Wi-Fi settings
page | Wi-Fi | Saved networks.
3.
Tap the plus sign icon to open the Add network dialog box.
4.
Enter the SSID (name) of the network. If the network is secured, tap the
triangle at the right of the Security field to select the type of security
deployed on the network and enter any required security credentials.
- 26 -
Using the Mobile Computing Device
5.
Tap Save.
The K500 then proceeds to connects to the Wi-Fi network. Any credentials entered
are saved so the K500 automatically connects it the next time the K500 gets it within
the range.
3.4.3 Connecting to a Wi-Fi Network by WPS
Wi-Fi Protected Setup (WPS) is a feature that allows WPS-compliant devices to
connect to each other instantly in a secure way. As the WPS devices automatically
configure the SSID and WPA security key, it eliminates the need for users to
manually enter the SSID and password. WPS works in two methods: Push or
personal identification number (PIN). To connect to a Wi-Fi network via WPS:
1.
Swipe down the Status bar and tap the WI-FI tile to enable Wi-Fi if it isn't
enabled yet.
2.
In the Quick Settings panel, tap and hold the WI-FI tile to access the Wi-Fi settings
page. Wi-Fi | Wi-Fi preferences | Advanced | WPS Push Button
- 27 -
Using the Mobile Computing Device
3.
Use either of the following methods to make the connection:
To use Push button, tap the WPS icon in the upper right corner and a
prompt message will appear. Then press the WPS button on your WPS router
within two minutes
To use PIN method, tap the WPS Pin Entry to open the context menu and then
tap WPS Pin Entry. You will be prompted with a PIN. Enter that PIN on your Wi-
Fi router within two minutes.
4.
WPS authentication process will start. When the authentication is done, you
will be prompted that connection is successful.
- 28 -
Using the Mobile Computing Device
3.4.4 Forgetting/Modifying a Wi-Fi Network
When you don’t want the K500 to "auto" connect to a Wi-Fi network or when it is a
network that you no longer use, remove the Wi-Fi network by the steps below:
1.
Swipe down the Status bar and tap the WI-FI tile to enable Wi-Fi if it isn't
enabled yet.
2.
In the Quick Settings panel, tap and hold the WI-FI tile to access the Wi-Fi settings
page.
3.
On the Wi-Fi settings screen, tap network to forget.
4.
Tap Forget.
Some Wi-Fi networks may periodically change their passwords to enhance the
network security. When this occurs, you need to change the saved login credentials.
To change the password, follow the steps above to access the context menu of the
intended network. Then tap Modify network to make the changes.
3.4.5 Making Your Device a Wi-Fi Hotspot
When the K500 is connected to a 3G network, you can share the connection with your
laptop or other devices by making your K500 a Wi-Fi hotspot. To do so:
1.
Swipe down the Status bar and tap SETTINGS | NETWORK &
INTERNET | Hotsport & tethering | Wi-Fi hotspot.
2.
Tap Wi-Fi hotspot slider to enable the hotspot function.
3.
Tap Set up Wi-Fi hotspot to configure the settings as needed:
• Network name: Enter a name to identify the wireless network created by
the K500.
• password: To prevent your device from being accessed by unauthorized
users, it is strongly recommended that you set up a password to protect
your network.
- 29 -
Using the Mobile Computing Device
When Wi-Fi hotspot is enabled, a Wi-Fi hotspot icon will appear in the
Notification Area. You can swipe down the icon to see the connection
information.
3.5 Using the Bluetooth Feature
Bluetooth enables the wireless connection over a short distance about 8 meters. It is
specified as a "wireless personal area network" (WPAN). The K500 is Bluetoothcapable to synchronize data with other Bluetooth-capable devices such as PCs,
laptops, hands-free, headsets, printers, PDAs and cell phones.
Before the K500 can connect a Bluetooth device, it needs to pair with that device.
Such “pairing” involves the authentication between them to justify their accesses to
each other. Once they are paired, they stay paired unless they are unpaired.
The Status bar displays the following icons that indicate Bluetooth status.
Icon
Description
Bluetooth is on.
Connected to a Bluetooth device.
- 30 -
Using the Mobile Computing Device
3.5.1 Enabling Bluetooth and Pairing with Bluetooth Device
To enable or disable the Bluetooth function:
1.
Swipe down the Status bar and tap the BLUETOOTH tile to enable
Bluetooth if it isn't enabled yet.
2.
In the Quick Settings panel, tap and hold the BLUETOOTH tile to access the
Bluetooth settings page.
3.
If the Bluetooth device you want to pair with is not displayed in the AVAILABLE
DEVICES list, tap Pair new device.
The K500 proceeds to scan for any Bluetooth device in range. Then it displays
the names of the device(s) found.
If the K500 stops scanning before the other device becomes discoverable, tap
Pair new device again.
Note: If the device to pair with isn’t displayed after the scan, check if it is
configured to be discoverable.
4.
Tap the device you want to pair with. When the Bluetooth pairing request dialog
box appears, tap Pair. The K500 will then send a connection request to the
deviceyou want to pair with.
- 31 -
Using the Mobile Computing Device
On the device to pair with, a dialog box appears requesting to enter or verify the
pairing code. The passkey entered or shown on the K500 and the Bluetooth device
must be the same.
If you’re prompted to enter a pin code, try entering 0000 or 1234 (the most
common pin code), or look up in the documentation that came with the other
Bluetooh device to learn its pin code.
Then the devices proceed to pair with each other.
3.5.2 Configuring Bluetooth Features to Use
A "Bluetooth profile" defines the features supported by a Bluetooth device. For two
Bluetooth devices to share files with each other, they need to both support the right
profile. Some Bluetooth devices have multiple profiles. A profile can provide the
ability to transmit phone conversations, to play music in stereo, or to transfer files or
other data. The operating system allows you to configure the profiles you want to
use on the K500.
1.
Swipe down the Status bar and tap the BLUETOOTH tile to enable
Bluetooth if it isn't enabled yet.
2.
In the Quick Settings panel, tap and hold the BLUETOOTH tile to access the
Bluetooth settings page.
3.
Tap the icon at the right of a paired device.
A "Paired Bluetooth device" page opens for that paired device.
4.
Select or deselect a profile to use it
- 32 -
Using the Mobile Computing Device
3.5.3 Disconnect from a Bluetooth Device
To disconnect the K500 from a Bluetooth device:
1.
Swipe down the Status bar. In the Quick Settings panel, tap and hold the
BLUETOOTH tile to access the Bluetooth settings page.
2.
In the PAIRED DEVICES list, find the device to disconnect.
3.
Tap the icon at the right of the device.
A "Paired Bluetooth device" page opens for that paired device.
4.
Tap FORGET.
The selected device is unpaired and disconnected.
3.5.4 Making Your Bluetooth Device Discoverable
To allow other Bluetooth-enabled device to find the K500, you have to make sure the
K500 is visible to other devices in addition to enabling Bluetooth feature. After you
turn on the Bluetooth the K500 will be visible.
- 33 -
Using the Mobile Computing Device
3.5.5 Additional Bluetooth Settings
From the Bluetooth settings page, tap the menu icon on to get the following
options:
1.
Device name: Allows you to edit the Bluetooth name of the K500 that will be
shown to others when they try to search for it.
2.
Received files: Open the location where downloaded and uploaded Bluetooth
files are stored.
- 34 -
Using the Mobile Computing Device
3.6 Using the Location Feature
The K500 features positioning function to identify your location. It allows locationbased Apps to collect and use your location information to provide location-related
service. For example, a third-party App might want to pinpoint a vehicle’s location so
as to provide a more efficient route for the driver upon traffic congestion. For a
location-based App, you can individually configure whether it is allowed to access to
location services when the service is on.
Note: When your turn off the location service, you also turn it off for the Apps that
use this service. That means location-based service will stop and not be available.
3.6.1 Enabling/Disabling Location Service
To turn on or off location service, swipe down the Status bar to bring up the
Quick Settings panel. Then access the Security & location | Location tile to turn it
on or off.
3.6.2 Location Mode
In addition to GPS satellite method, the K500 also supports Assisted GPS (A-GPS), a
method using Wi-Fi and cellular networks to speed up startup positioning
performance. According to the position mode, the battery drain and position
accuracy varies.
To select a location position mode when the location service is on,
1.
Swipe down the Status bar and tap the LOCATION tile to enable the
location service if it isn't enabled yet.
2.
In the Quick Settings panel, tap and hold the LOCATION tile to access the
location settings page.
3.
Tap Mode and select a mode:
• High accuracy: This mode uses GPS, Wi-Fi and cellular networks to determine
location. It drains the battery faster yet higher accuracy is achieved
compared to the other two modes. Select this mode if precise location
matters to you.
- 35 -
Using the Mobile Computing Device
• Battery saving: This mode uses Wi-Fi and cellular networks to determine
your location. Select this mode if you need to extend the battery life.
• Device only: This mode determines your location using GPS only.
Without using Wi-Fi and cellular networks to improve the startup
process, it takes longer to determine the location.
3.7 Using Camera
The device is equipped with one camera: a back- facing camera with LED flash.
To access the camera application, on the Home screen tap the camera icon
The camera application then opens.
- 36 -
Using the Mobile Computing Device
When taking a photo:
• To zoom in and out, place two fingers apart or together.
• When you frame your subject on the screen, the camera will Auto Focus on the
center of the screen with a focus indicator. To manually make a focus, tap the
target or area that you want to focus on.
• To take a photo, press the shutter icon.
When recording a video:
• To enable/disable the microphone, tap the Settings icon and then video icon.
• To start the recording, tap the Recorder icon and the timer starts.
• To stop the recording, tap the Recorder icon again.
- 37 -
Using the Mobile Computing Device
3.8 Using the NFC Feature
Near Field Communication (NFC) is a short-range wireless communication technology
that enables NFC-capable devices to exchange data such as contacts, photos, music,
or web address over a short distance less than 4 centimeters.
The NFC detection area is at the back side of the K500. When you tap other NFC
devices, tags, or readers, the NFC areas of both devices should be close to one
another so that the connection can be established.
3.8.1 Enabling/Disabling NFC
To enable or disable the NFC function:
1.
Swipe down the Status bar and tap Settings | Connected devices | NFC.
2.
Tap the NFC slider to turn it on or off.
3.8.2 Configuring NFC Modes
The K500 supports three NFC modes.
- 38 -
Using the Mobile Computing Device
3.8.3 Exchanging Data with NFC-Enabled Device
To use NFC to exchange App contents, both sending and receiving devices must be
NFC-enabled and unlocked. The following describes how to beam App content from
the K500 to another NFC device:
1.
Make sure both devices are NFC-enabled. For your K500, enable NFC as
described in 3.7.1 Enabling/Disabling NFC if it isn't enabled yet.
2.
Open the content you want to exchange.
3.
Make sure the screen of both devices are unlocked, then touch the devices
together, back to back.
4.
On the K500, you will hear a sound and be prompted a message "Touch to
beam". Touch the screen of the K500 to begin the beaming process.
5.
The content will appear on the other devices's screen.
- 39 -
Using the Mobile Computing Device
3.9 Using the Barcode Scanner
Barcode scanner is an optional feature on the K500. Depending on your models, your
K500 might be equipped with1D/ 2D barcode scanner. This section will walk you
through the basic operations. To get the information on supported barcode formats,
see 3.8.3 Supported Barcode Formats for details.
Caution: The barcode scanner uses laser lights to scan barcodes. DO NOT stare into
the laser beams or point the laser beam at anyone's eyes when the barcode scanner
is in operation.
3.9.1 Installing APK File
As of the time of time of release, the K500 may not have the barcode scanner
software installed. If this is the case, you must install the APK file on your K500 first
in order to activate the scanner function.
1.
Download the APK file
(SignedBarcodeSample.apk) from the Partner
Zone of our website and save the file to your
computer first.
2.
Connect the K500 to that computer using a USB
cable. The K500 will prompts you to
choose a USB option. Select "USB storage" to
transfer files between your computer and the
K500.
3.
Copy the APK file from your computer to the
K500's internal USB storage or SD card. Then
disconnect your computer from the K500.
4.
On the K500, use the File Manager App to
navigate to the APK file.
LASER RADIATION
- 40 -
Appendices
5.
Tap the APK file and then follow the prompts to install the application.
3.9.2 Scanning the Barcode
Generally a third-party barcode application will be used to process the data read by
the scanner. This user manual will not cover these applications. The following steps
serve as an example only to show the basic operation of the barcode scanner.
1.
To scan a 2D barcode like QR code: Launch the web browser.
2.
Point the scanner window at the barcode and press either of the two Scan
keys. The scanner will project an aiming beam.
3.
According to the barcode scanned, the scanned data is displayed in the text
field or an action is triggered .
- 41 -
Appendices
3.9.3 Supported Barcode Formats
2D Model
Type
Formats
Linear
Code 39, Code 128, Code 93, MSI
2D Stacked
PDF417,
2D Matrix
Aztec Code, Data Matrix, QR Code, Codablock –F, Micro PDF417, , Micro QR
Code, Han Xin Code, Royal Main Mailmark 2D, NTIT Code, PPN Code,
Switzerland QR Code,
Postal
Australian Post Standard Customer, Japanese Post, Korean Postal
Authority Code, Planet Code 12, Royal Mail 4-State, USPS PostNet 5,
USPS PostNet 9, USPS PostNet 11, UPU S10
Product code
100% UPCA
Loading...