Page 1
Page 2
CONTENTS
1. Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4. Remote Control. . . . . . . . . . . . . . . . . . . . . . 4
5. Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . 6
6. Rear Panel. . . . . . . . . . . . . . . . . . . . . . . . . . 9
7. Connecting Your System. . . . . . . . . . . . . .11
8. Basic Operations . . . . . . . . . . . . . . . . . . . 15
8.1 Turn On Stb . . . . . . . . . . . . . . . . . . . . . 15
8.2 Power . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.3 Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.4 Pause . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.5 Recall . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.6 Favorite . . . . . . . . . . . . . . . . . . . . . . . . 15
8.7 Audio . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.8 Information . . . . . . . . . . . . . . . . . . . . . . 15
8.9 EPG . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.10 Tv/Radio . . . . . . . . . . . . . . . . . . . . . . . 16
8.11 Channel List . . . . . . . . . . . . . . . . . . . . 16
8.12 Sleep . . . . . . . . . . . . . . . . . . . . . . . . . 17
8.13 Page Up/Page Down . . . . . . . . . . . . . 17
8.14 Text . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8.15 Subtitle . . . . . . . . . . . . . . . . . . . . . . . . 17
8.16 Find . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8.17 Zoom . . . . . . . . . . . . . . . . . . . . . . . . . 17
8.18 TV/Sat . . . . . . . . . . . . . . . . . . . . . . . . 17
8.19 Menu . . . . . . . . . . . . . . . . . . . . . . . . . 17
8.20 Video Format . . . . . . . . . . . . . . . . . . . 17
8.21 Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
9. Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
9.1 Organizing Service . . . . . . . . . . . . . . . . 17
9.2 Organizing Favourites . . . . . . . . . . . . . 19
10. Installation. . . . . . . . . . . . . . . . . . . . . . . . 19
10.1 Satellite Installation. . . . . . . . . . . . . . 19
10.2 Fastscan Satellite . . . . . . . . . . . . . . . 20
10.3 Auto Installation . . . . . . . . . . . . . . . . 20
10.4 Satellite Guide . . . . . . . . . . . . . . . . . 20
10.5 Terrestrial Installation . . . . . . . . . . . . 21
10.6 Cable Installation . . . . . . . . . . . . . . . 21
11. System. . . . . . . . . . . . . . . . . . . . . . . . . . . 21
11.1 Language . . . . . . . . . . . . . . . . . . . . . 21
11.2 A/V Control . . . . . . . . . . . . . . . . . . . . 22
11.3 Ethernet Setting . . . . . . . . . . . . . . . . 22
11.4 Time Setting . . . . . . . . . . . . . . . . . . . 23
11.5 Timer . . . . . . . . . . . . . . . . . . . . . . . . . 23
11.6 Parental Control . . . . . . . . . . . . . . . . 24
11.7 Miscellaneous Settings. . . . . . . . . . . 24
11.8 Software Upgrade. . . . . . . . . . . . . . . 24
11.8.1 Upgrade By Usb. . . . . . . . . . . . . . . 24
11.8.2 Http Upgrade . . . . . . . . . . . . . . . . . 24
11.8.3 Ftp Upgrade. . . . . . . . . . . . . . . . . . 25
11.8.4 Upgrade By Rs232: . . . . . . . . . . . . 25
11.8.5 Backup To Usb. . . . . . . . . . . . . . . . 25
11.9 Default Setting . . . . . . . . . . . . . . . . . 25
11.9.1 Default Value:. . . . . . . . . . . . . . . . . 26
11.9.2 Delete All Channel: . . . . . . . . . . . . 26
11.9.3 Save Default Value . . . . . . . . . . . . 26
11.10 Information . . . . . . . . . . . . . . . . . . . 26
12. Conditional Access . . . . . . . . . . . . . . . . 26
12.1 Ca Setting. . . . . . . . . . . . . . . . . . . . . 26
12.2 Common Interface . . . . . . . . . . . . . . 26
13. Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
13.1 Record . . . . . . . . . . . . . . . . . . . . . . . 27
13.2 Movie . . . . . . . . . . . . . . . . . . . . . . . . 27
13.3 Music . . . . . . . . . . . . . . . . . . . . . . . . 27
13.4 Image . . . . . . . . . . . . . . . . . . . . . . . . 28
13.5 PVR Setting . . . . . . . . . . . . . . . . . . . 28
13.6 Disk Manage. . . . . . . . . . . . . . . . . . . 29
13.7 Remove Usb Device Safely!. . . . . . . 29
14. Application . . . . . . . . . . . . . . . . . . . . . . . 29
14.1 Youtube. . . . . . . . . . . . . . . . . . . . . . . 29
14.2 Rss Reader. . . . . . . . . . . . . . . . . . . . 30
14.3 Weather Forecast . . . . . . . . . . . . . . . 30
14.4 Google Maps . . . . . . . . . . . . . . . . . . 30
14.5 FTP. . . . . . . . . . . . . . . . . . . . . . . . . . 30
14.6 Web TV. . . . . . . . . . . . . . . . . . . . . . . 31
15. EPG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
16. New Features . . . . . . . . . . . . . . . . . . . . . 31
16.1 Time Shift . . . . . . . . . . . . . . . . . . . . . 31
16.2 Record . . . . . . . . . . . . . . . . . . . . . . . 31
17. Trouble Shooting . . . . . . . . . . . . . . . . . . 32
18. Specifications . . . . . . . . . . . . . . . . . . . . . 32
European Union Directive on Waste Electrical and Electronic Equipment (WEEE)
This symbol applies to European countries only and indicates that the equipment carrying this mark must
NOT be thrown into trash. At the end of its useful life, always dispose of E-waste in a manner which is
consistent with local laws and regulations. For more information on the EU WEEE Directive, please see
http://ec.europa.eu/environment/waste/weee_index.htm
Page 3
USER’S MANUAL
1. SAFETY
This HD Receiver has been manufactured to satisfy the international safety standards. Please read the following safety precautions
carefully.
MAINS SUPPLY: 100~240V AC, 50/60Hz
OVERLOADING: Do not overload wall outlet, extension cord or adapter as this may result in fire or electric shock.
LIQUIDS: Keep liquids away from the HD Receiver. The apparatus shall not be exposed to dripping or splashing and that no
objects filled with liquids, such as vases, shall be placed on the apparatus.
CLEANING: Disconnect the HD Receiver from the wall outlet before cleaning .Use a light damp cloth (no solvents) to dust the HD
Receiver.
VENTILATION: The slots on top of the HD Receiver must be left uncovered to allow proper airflow to the unit. Do not stand the HD
Receiver on soft furnishings or carpets. Do not expose the HD Receiver to direct sunlight or do not place it near a heater. Do not
stack electronic equipments on top of the HD Receiver.
ATTACHMENTS: Do not use any attachments that are not recommended as these may cause hazard or damage the HD Receiver.
CONNECTION TO THE SATELLITE DISH LNB: Disconnect the HD Receiver from the mains before connecting or disconnecting
the cable from the satellite dish.
FAILURE TO DO SO CAN DAMAGE THE LNB.
CONNECTION TO THE TV: Disconnect the HD Receiver from the mains before connecting or disconnecting the cable from the
satellite dish.
FAILURE TO DO SO CAN DAMAGE THE TV.
EARTHING: The LNB cable MUST BE EARTHED to the system earth for the satellite dish.
LOCATION: Place the HD Receiver indoor in order not to expose to lightening, rain or sunlight.
2. INTRODUCTION
Thank you for purchasing the HD Receiver.
This HD Receiver is fully compliant with the international DVB standard and thus transmits digital images, sounds, information
guides and teletext directly to your TV through the satellite broadcasting.
Now you can comfortably see and receive digitally transmitted music, news, movie and sports satellite broadcasts in your office or
at your home. You can enjoy interesting games embedded in HD Receiver.
In service search section, both the automatic service search method and the manual search mode are provided. Also it supports
DiSEqC 1.0, 1.2 and USALS, enabling you to move your antenna in order to focus preferred satellite. You can save up to 6000 TV
and Radio services and work around with the favorite, Lock, Delete, Move and Sort functions.
The menu is very modern and supports multiple languages. All functions can be carried out using the remote control and some
of the functions can also be carried out using the front panel. The HD Receiver is easy to use and adaptable for future advances.
Please be aware that new software may change the functions of the HD Receiver.
If you have any difficulties concerning the operation of your HD Receiver, please refer to the relevant section of this manual, including the ‘Troubleshooting’. This Manual will provide you with useful information on using the HD Receiver.
3. FEATURES
●
MPEG-Fully DVB-S / DVB-S2 (H.264) HD compliant
●
6000 channels (TV and Radio) programmable
●
Multilingual menu text support
●
Channel switching time less than 1 second
●
Channel list editing
●
Favorite channel list editing
●
True-color On-Screen Display (OSD)
●
Full Picture In Graphic (PIG) function
●
Electronic Program Guide (EPG) for on screen channel information
●
Subtitle supported
●
Teletext supported by VBI insertion and software emulation
●
Parental lock facility by channel and program event
●
Program and Channel information transfer from receiver to receiver
●
Exciting games embedded
●
Dolby Digital Bit-Stream output via HD OUT
●
DiSEqC 1.0, 1.1, 1.2 ,USALS and Unicable
●
Full HD (1080p) Video/Audio Output
●
2x USB 2.0 Host
●
RTC (Real-Time-Clock)
●
Time Shift
●
Video Recording
●
Recording one channel and Time Shifting another channel (optional)
●
3G Network Function Supported
3
Page 4
4
4. REMOTE CONTROL
(AMIKO HD8140C SE / HD8142 / HD8155 / HD8265+ / MINI HD265 / MINI
COMBO EXTRA / MIRA WIFI / IMPULSE T2C)
You can power on/off the receiver, operate on screen menu, and use a variety of
hot key function.
POWER To switch your receiver on from standby or standby to on.
MUTE Used to enable or disable the audio
NUMERIC KEYS Used to select channels or enter programming parameters
TV / RADIO Receiver switches between TV and Radio mode.
(ZOOM) Press key select zoom times, from X1 to X16.
RECALL Return to the previous menu or status.
TV/SAT Receiver switches between TV and receive mode.
INFO To display channel status or various program information of current service.
EPG (Electronic Program Guide) Display the Programs guide on screen when
available.
MENU Displays the Main Menu on the screen, or return to the previous menu or
status.
EXIT Cancel the user selection and return to the viewing mode from a menu.
OK To select menu option, or to updated on entry.
◄/►
KEY To adjust volume level, or to move cursor left or right in the menu.
▼/▲
KEY To change channels, or to move cursor up or down in the menu.
►
/PAGE ► To move up the cursor to the next or previous page in the
PAGE
menu or channel list.
● REC Has different functions per menu.
Teletext Shows teletext information of the current channel supports.
Subtitle Subtitle Display.
UHF In case your TV is connected through RF Modulator (UHF), select output
channel number between CH21 and CH69 with up and down key.
(FIND) Use to prompt find channels sort by character.
TIMER Press timer key you can setup up the Standby time.
V.FORMAT Press V.FORMAT button to switch the display mode among „AUTO”,
„By Native TV”, ”480p”, „576P”, „720P_50”, ”720P_60, ”1080i_50”, ”1080i_60” ,
”1080P_50” and ”1080P_60”
FAV (FAVORITE) To set receiver to the favorite server mode, display the favorite
channel.
FOLDER Press this button to enter the Record Manager menu directly.
AUDIO (Red Key) Audio channels setup, to select audio mode; Left, Right ,
Stereo, Mono.
OPTION (GREEN KEY) Shows NVOD information of the current channel supports.
SAT Display the satellite list at normal picture.
Play Mode Select the play mode in MP3 or JPEG player.
USB To remove the USB Hard Disk safely.
TMS (Time Shift) Press this button to display Time Shift info bar.
► Play To play the MP3, JPEG, or Record files.
Stop To stop the Time Shift, recording, or MP3/JPEG player.
II PAUSE Used to select the freeze function. Press once to freeze the screen
picture.
◄◄
FB To start Fast Backward function.
►► FF To start Fast Forward function.
◄I
SB To start Slow Backward function.
I
► SF To start Slow Forward function
◄◄/►►I
PREV/NEXT Switch to preview or next file in play mode
USER’S MANUAL
Page 5
USER’S MANUAL
5
(AMIKO T60 / T70)
POWER To switch your receiver on from standby or standby to on.
MUTE Used to enable or disable the audio
NUMERIC KEYS Used to select channels or enter programming parameters
TV / RADIO Receiver switches between TV and Radio mode.
(ZOOM) Press key select zoom times, from X1 to X16.
(RECALL) Return to the previous menu or status.
(AUDIO) Audio channels setup, to select audio mode; Left, Right , Stereo, Mono.
INFO To display channel status or various programme information of current
service.
EPG (Electronic Programme Guide) Display the Programmes guide on screen
when available.
MENU Displays the Main Menu on the screen, or return to the previous menu or
status.
EXIT Cancel the user selection and return to the viewing mode from a menu.
OK To select menu option, or to updated on entry.
VOL-, VOL+ KEY To adjust volume level, or to move cursor left or right in the
menu.
CH-, CH+ KEY To change channels, or to move cursor up or down in the menu.
PAGE+/PAGE- To move up the cursor to the next or previous page in the menu or
channel list.
Red Key Has different functions per menu.
TTX (GREEN KEY) Shows teletext information of the current channel supports.
SUBTITLE (YELLOW KEY) Subtitle Display.
(FIND) Use to prompt find channels sort by character.
FAV (FAVOURITE) To set receiver to the favourite server mode, display the
favourite channel.
Archive Press this button to enter the File Manager menu directly.
► Play To play the MP3, JPEG or recording file, or start timeshift function.
Stop To stop MP3/JPEG player, recording file , Time Shift, or playback.
● Record To start recording.
◄◄
Fast Backward To start Fast Backward function.
►► Fast Forward To start Fast Forward function .
V.FORMAT Press VFORMAT button to switch the display mode among „Auto-> by
native TV<->1080i->1080p etc.
TV/STB Receiver switches between TV and receive mode.
Page 6
6
5. FRONT PANEL
AMIKO HD8140C SE
STANDBY KEY: To switch the receiver power on/stand by.
MENU KEY: To enter the Main Menu.
OK KEY: To see TV/Radio channel list, or to confirm in the menu.
V-/V+ KEY: To adjust volume level, or to move cursor left or right in the menu.
CH-/CH+ KEY: To change channels, or to move cursor up or down in the menu.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
Card Slot: One CA Interface for Conax.
Display: (LED type) Indicates operating status of receiver.
AMIKO HD8142
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
USB: USB 2.0 Host, connect to USB hard disk, flash disk, WiFi dongle, 3G dongle. (On the right side of the receiver)
Display: (LED type) Indicates operating status of receiver.
POWER KEY: To switch the receiver power on/stand by.
CH-/CH+ KEY: To change channels, or to move cursor up or down in the menu.
Card Slot: One slot CA Interface for Conax Smartcard (on left side).
USER’S MANUAL
POWER KEY: To switch the receiver power on/stand by.
MENU KEY: To enter the Main Menu.
OK KEY: To see TV/Radio channel list, or to confirm in the menu.
V-/V+ KEY: To adjust volume level, or to move cursor left or right in the menu.
CH-/CH+ KEY: To change channels, or to move cursor up or down in the menu.
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
Card Slot: One CA Interface for Conax.
USB A: USB 2.0 Host, connect to USB hard disk, or flash disk,and 3G dongles.
Display: (LED type) Indicates operating status of receiver.
POWER KEY: To switch the receiver power on/stand by.
MENU KEY: To enter the Main Menu.
OK KEY: To see TV/Radio channel list, or to confirm in the menu.
LEFT/RIGHT KEY: To adjust volume level, or to move cursor left or right in the menu.
UP/DOWN KEY: To change channels, or to move cursor up or down in the menu.
Remote Sensor: Detects infrared signal from remote control unit.
AMIKO HD8155
AMIKO HD8265+
Page 7
USER’S MANUAL
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
Card Slot: One CA Interface for Conax.
Common Interface: One socket for Conditional Access Modules CAM.
USB A: USB 2.0 Host, connect to USB hard disk, or flash disk,and 3G dongles.
Display: (LED type) Indicates operating status of receiver.
AMIKO MINI HD265
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
Card Slot: One CA Interface for Conax.
USB (on the side): USB 2.0 Host, connect to USB hard disk, or flash disk,and 3G dongles.
Display: (LED type) Indicates operating status of receiver.
RS 232 (on the side): This is used to connect your receiver to a computer through a serial cable.
IR IN( on the side): Connect an External IR-Sensor (Infrared).
AMIKO MINI COMBO EXTRA
7
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
Card Slot: One CA Interface for Conax.
USB (On the side): USB 2.0 Host, connect to USB hard disk, or flash disk,and 3G dongles.
Display: (LED type) Indicates operating status of receiver.
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
Card Slot: One CA Interface for Conax.
USB (On the side): USB 2.0 Host, connect to USB hard disk, or flash disk,and 3G dongles.
Display: (LED type) Indicates operating status of receiver.
AMIKO MIRA WIFI
Page 8
8
AMIKO IMPULSE T2C
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
Card Slot: One CA Interface for Conax. Under the receiver.
USB: USB 2.0 Host, connect to USB hard disk, or flash disk (on the right side of the receiver).
Display: (LED type) Indicates operating status of receiver.
AMIKO T60
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
USB: USB 2.0 Host, connect to USB hard disk, or flash disk (on the right side of the receiver).
Display: (LED type) Indicates operating status of receiver
Buttons: (Standby, CH-, CH+, V-, V+) to operator the receiver.
USER’S MANUAL
AMIKO T70
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
USB: USB 2.0 Host, connect to USB hard disk, or flash disk (on the right side of the receiver).
Display: (LED type) Indicates operating status of receiver
Buttons: (Standby, CH-, CH+) to operator the receiver.
Page 9
USER’S MANUAL
6. REAR PANEL
AMIKO HD8140C SE
RF IN: This port is to connect the coaxial cable from Cable Antenna.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
USB: USB 2.0 Host, connect to USB hard disk, or flash disk,and wifi dongles.
TV: This is used to connect your TV through SCART cable.
DV OUT: Audio and Video output socket for TV set with DV OUT Input Jack only.
RS 232 SERIAL PORT: This is used to connect your receiver to a computer through a serial cable.
Ethernet: Network port, you can get a new software updates from this port.
POWER ON/OFF SWITCH: To switch ON/OFF the receiver power supply.
AMIKO HD8142
RF IN: This port is to connect the coaxial cable from Cable Antenna.
Ethernet: Network port, you can enjoy the network application function via this port, or you can get new software updates or new
games.
HD OUT: Audio and Video output socket for TV set with HDMI Input Jack only.
RS 232 SERIALPORT: This is used to connect your receiver to a computer through a serial cable.
VIDEO: This RCA connector is used to connect any external video.
AUDIO R/L: These RCA connectors are used to connect any external audio amp or system.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
HDD: To connect internal HDD.
DC 12V: This is used to connect an external 12V adapter.
9
AMIKO HD8155
Please refer to the diagram above for all possible connections of your receiver
Do not connect the unit to the mains socket until all other connections have been made and checked.
LNB IN 13/18V 400mA MAX: This port is to connect the coaxial cable from LNB of your Dish.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
HDMI: Audio and Video output socket for TV set with HDMI Input Jack only.
RS 232: This is used to connect your receiver to a computer through a serial cable.
Ethernet: Network port, you can get a new software updates from this port.
TV: This SCART connector is used to connect TV using SCART cable.
POWER ON/OFF SWITCH: To switch ON/OFF the receiver power supply.
USB: USB 2.0 Host, connect to USB hard disk, or flash disk,and 3G dongles.
AMIKO HD8265+
Please refer to the diagram above for all possible connections of your receiver
Do not connect the unit to the mains socket until all other connections have been made and checked.
LNB IN 13/18V 400mA MAX: This port is to connect the coaxial cable from LNB of your Dish.
RF IN: This port is to connect the coaxial cable from Terrestrial/Cable Antenna.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
USB B: USB 2.0 Host, connect to USB hard disk, or flash disk,and 3G dongles.
AV OUT: This RCA connector is used to connect any external video and audio.
HD OUT: Audio and Video output socket for TV set with HDMI Input Jack only.
RS 232 SERIAL PORT: This is used to connect your receiver to a computer through a serial cable.
Ethernet: Network port, you can get a new software updates from this port.
IR IN: Connect an External IR-Sensor (Infrared).
DC 12V: This is used to connect an external 12V adapter.
Page 10
10
AMIKO MINI HD265
Please refer to the diagram above for all possible connections of your receiver
Do not connect the unit to the mains socket until all other connections have been made and checked.
LNB IN 13/18V 400mA MAX: This port is to connect the coaxial cable from LNB of your Dish.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
HD OUT: Audio and Video output socket for TV set with HDMI Input Jack only.
Ethernet: Network port, you can get a new software updates from this port.
RCA: This RCA connector is used to connect TV using AV cable.
DC 12V: This is used to connect an external 12V adapter.
AMIKO MINI COMBO EXTRA
Please refer to the diagram above for all possible connections of your receiver
Do not connect the unit to the mains socket until all other connections have been made and checked.
LNB IN 13/18V 400mA MAX: This port is to connect the coaxial cable from LNB of your Dish.
RF IN: This port is to connect the coaxial cable from Terrestrial/Cable Antenna.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
HD OUT: Audio and Video output socket for TV set with HDMI Input Jack only.
RS 232: This is used to connect your receiver to a computer through a serial cable.
Ethernet: Network port, you can get a new software updates from this port.
AV OUT: This RCA connector is used to connect TV using RCA cable.
IR IN: Connect an External IR-Sensor (Infrared).
DC 12V: This is used to connect an external 12V adapter.
USER’S MANUAL
AMIKO MIRA WIFI
Please refer to the diagram above for all possible connections of your receiver
Do not connect the unit to the mains socket until all other connections have been made and checked.
LNB IN 13/18V 400mA MAX: This port is to connect the coaxial cable from LNB of your Dish.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
HD OUT: Audio and Video output socket for TV set with HDMI Input Jack only.
TV: This SCART connector is used to connect TV using SCART cable.
IR IN: Connect an External IR-Sensor (Infrared).
DC 12V: This is used to connect an external 12V adapter.
AMIKO IMPULSE T2C
DC 5V:This is used to connect an external 5V adapter.
TV: This is used to connect your TV through SCART cable.
HDMI: Audio and Video output socket for TV set with HDMI Input Jack only.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
RF IN: This port is to connect the coaxial cable from Terrestrial/Cable Antenna.
AV OUT: This RCA connector is used to connect TV using RCA cable.
Page 11
USER’S MANUAL
AMIKO T60
DC 5V:This is used to connect an external 5V adapter.
TV: This is used to connect your TV through SCART cable.
HD OUT: Audio and Video output socket for TV set with HDMI Input Jack only.
RF IN: This port is to connect the coaxial cable from Terrestrial/CableAntenna.
AMIKO T70
DC 5V: This is used to connect an external 5V adapter.
TV: This is used to connect your TV through SCART cable.
HD OUT: Audio and Video output socket for TV set with HDMI Input Jack only.
RF IN: This port is to connect the coaxial cable from Terrestrial/CableAntenna.
7. CONNECTING YOUR SYSTEM
There are two ways to connect the receiver to your existing TV system. We recommend using one of the following cases for the
best result:
1. If you have a high definition television set, you should use a HDMI cable for best result, Plug one end of the cable into the HD
OUT socket on the receiver, and the other end into the matching socket on your television. In this case, you do not have to make
audio connections because the HDMI connector can output stereo audio or Dolby Digital audio.
2. Connect one end of RCA cable to the RCA jack on the back of the receiver and the other end to a RCA jack on your TV.
11
AMIKO HD8140C SE
AMIKO HD8142
Page 12
12
USER’S MANUAL
AMIKO HD8155
AMIKO HD8265+
AMIKO MINI HD265
Page 13
USER’S MANUAL
AMIKO
MINI COMBO
EXTRA
13
AMIKO MIRA WIFI
AMIKO IMPULSE T2C
Page 14
14
USER’S MANUAL
AMIKO T60
AMIKO T70
Page 15
USER’S MANUAL
8. BASIC OPERATIONS
8.1 TURN ON STB
First, open the power switch to turn on the unit.
When the STB is first used, there will play the first channel from
the default Channel List. If the STB is not first used, STB will
play the same channel as last time before turning off.
8.2 POWE R
1. Press [Power] Key can enter the Standby state
2. In Standby state, press [Power] Key again can call back the
unit and go on play the previous channel
3. User can also disconnect the device’s main power to end the
Standby state.
8.3 MUTE
1. Press [MUTE] key to mute the sound and the screen will
show up mute OSD.
2. Press [MUTE] key again to restore sound.
8.4 PAUSE
1. In playing mode, press [Pause] key, the picture will be
paused, but the sound of the channel will still continues.
2. Press [Pause] key again, the screen’s picture will skip over to
the current playing picture, and the sound of the channel will
corresponding playing.
8.5 RECALL
Press [RETURN] key will directly switch to the previous channel
that you played before current channel.
8.6 FAVORITE
1. In full screen, press [FAV] key, it will display a window of
”Favorite list” on the left of the screen, which you can watch
like below.
15
8.8 INFORMATION
In full screen, press [INFO] key (press [INFO] key and [RED]
key) can open information screen, in the window shows the
parameters of current channel.
8.9 EPG
1. The STB has an Electronic Program Guide (EPG) to help you
navigate channels through all the possible viewing options.
The EPG supplies information such as channel listings and
starting and ending times for all available channels. Press
[EPG] key to display EPG screen.
2. In the window of ” Favorite list ”, you can move highlight by
press [Channel Up/Channel Down] key to select favorite
Channels.
3. In the window of ” Favorite list ”, you can press [Left/Right]
key to select favorite groups Pressing [P-/P+] keys can implement the ”Page up/Page down” function
4. Press [Exit] key to exit the current window.
8.7 AUDIO
1. In full screen, press [AUDIO] key can open the ”Audio” window on the screen.
2. You can modify the audio track by press [Channel Up /
Channel Down] key and modify the audio mode by press[left/
right] key.
3. Mode: Left/Right/Stereo/Mono
2. Press [Red] key can select the channels by different group,
such as by Favorite/Satellite/Provider/CAS etc.
3. Press [Green] key to select different display mode among
Now EPG, Next EPG, More and Schedule, like the following
picture:
Page 16
16
4. Press [Yellow] key in EPG menu can set one record timer or
go to Timer List menu.
USER’S MANUAL
2. Press [Red] key to change the different group. Which you can
watch like below.
3. Press [Green] key to display details information for EPG Now.
4. Press [Yellow] key you can change the current channel’s
property, such as FAV/ Lock/ Skip/ Delete/ Rename.
5. In EPG menu, when you select one event by high light item,
you can set this event to record timer list directly by press
[REC] button.
6. In EPG menu, press [Exit] to close EPG screen.
8.10 TV/RADIO
In TV mode, pressing [TV/RADIO] key can switch to Radio
mode. In Radio mode, press [TV/RADIO] key to switch to TV
mode.
8.11 CHANNEL LIST
1. In full screen, press [OK] key can enter ”Channel List”.
5. Press [Blue] key can open the ”Sort” window like below.
There are five kinds of sorting ways. You can press [Channel
Up/Channel Down] key to move highlight and press [OK] key
to confirm you selection.
6. The five kinds of sorting way are:
• Default: Sorting by scanning result.
• FTA/$: Sort channel through free and scramble sequence.
Free channel will in the front of channel list and scramble
channel will at the rear of channel list
Page 17
USER’S MANUAL
17
• Lock: Accumulated all locked channels and list in the last of
TV Channel List.
• Name (A-Z): Sorting in Alphabetical Order, ignore ”$” symbol.
• Name (Z-A): Sorting in Alphabetical Order, ignore ”$” Symbol.
7. Press [Up/Down] key to move highlight and press [OK] key to
play the highlighted channel.
8. Press [Page Up/Down] key to page up and page Down.
9. Press [Exit] key to exit the channel list.
8.12 SLEEP
1. This function can set sleep timer. When you set a sleep timer
and the time arrive, the system will enter to standby automatically.
2. Pressing [SLEEP] key, it will switch the mode between Sleep
Timer Off /10/30/60/90/120 minutes.
8.13 PAGE UP/PAGE DOWN
In Channel list, press [Page+/Page-] key can page up and page
down the channel list.
8.14 TEXT
1. Press [TTX] key in full screen, you can open teletext page on
the channel which has teletext information.
2. If the channel has no teletext information, it will show ”No
Teletext Data” on the screen.
8.15 SUBTITLE
1. Press [SUBTITLE] key in full screen you can select the subti-
tle language or off on the channel which has subtitle.
2. If you set the Auto subtitle option as ON in Miscellaneous set-
tings menu, the subtitle will be showed automatically.
8.16 FIND
8.18 TV/S AT
Press [TV/Sat] key can switch between TV mode and STB
mode
8.19 MENU
Press [MENU] key can open the menu, exit the current menu to
last menu or close the window.
8.20 VIDEO FORMAT
Press [V. Format] key under Full Screen playback for 1st, it
will show the current system outputting video resolution, continuously press this key, system will switch its outputting video
resolution by sequence ” 480i-> 480P-> 576i-> 576p-> 720P->
1080i->1080p”.
8.21 EXIT
1. Press [EXIT] key can exit the current menu to last menu or
close the window.
9. SERVICE
When you press [Menu] key to enter menu, there will display the
picture like below:
1. Press[Find] key in full screen can open the ”Find” window like
above. You can press[Up/Down/left/right ]key to move highlight and press[OK]key to input the selected symbol or letter
into the dialogue.
2. After input each character, the program list on the left will
search the channel according your input, and list the matched
channel.
3. Move highlight to ”OK” and press [OK] key can close ”Find”
window and you can select channel from the channels list
directly.
8.17 ZOOM
1. The [ZOOM] key allows you to magnify a certain area on the
images
2. Press [ZOOM] key again, the image will enlarge rotate as x1,
x2, x4, x6, x8, x12, x16.
3. In ”x2 ~ x16” image, using [Up/ Down/ Up/ Down] keys to
move the image center area you want to see.
4. In zoom mode, press [Exit] to close ”Zoom” window.
1. Press[Left/Right] key you can select the submenu of
Organizing services and Organizing favourites.
2. Press [OK] key to enter the ”Organizing Service”. If Menu
Lock is ”On”, it will display an dialogue for user to key in
password. The default Password is ”0000”.
3. Press [Menu] key to go back to main menu.
9.1 ORGANIZING SERVICE
When you enter to ”Organizing Service” menu, there will display
the screen like below.
1.
You can move highlight by press [Channel Up/Channel Down]
key and [OK] key to select the programs which you want to edit.
2. You can press [Page Up/Page Down] key to implement the
Page Up/Page Down function.
3. You can use [Red] key to switch different Group.
4. You can press [Green] key to select the programs by different
select mode.
Page 18
18
USER’S MANUAL
5. Press color key can implement the corresponding function in
”Organizing Services”.
Groups
1. Press [Red] key can open the ”Groups” window like above
2. You can press [Up/Down] key to move highlight and press
[OK] key to select group.
3. Press [Menu] key to close ”Groups” List.
Options
Lock
1. Select the channels which you want to edit in channel list by
press [OK] key or other select mode.
2. Then press [Right] key to move the high light to right toolbar.
3. Select Lock icon by press [Channel Up/Channel Down] key
and [OK] key.
4. Lock the channel by press [OK] key. Like the following picture:
Delete
1. Select the channels which you want to edit in channel list by
press [OK] key or other select mode.
2. Then press [Right] key to move the high light to right toolbar.
3. Select Delete icon by press [OK key to delete channel one
by one.
4. When you high light in channel list ,you can press [OK] key
to select more channels ,and repeat b and c step to deleted.
Skip and rename
Follow the same way you can set the channel’s Skip or give the
new name for high light channel.
1. Press [Green] key can open the ”Options” window like above.
2. You can press [Up/Down] key to move highlight and press
[OK] key to confirm the select mode.
3. Press [Menu] key to close ”Options” List.
Move
1. Select the channels which you want to edit in channel list by
press [OK] key or other select mode.
2. Then press [Right] key to move the high light to right toolbar.
3. Select Move icon by press [Channel Up/Channel Down] key
and [OK] key.
4. Move the channels to the position which you want and press
[OK] key to confirm. Like the following picture:
Find
1. Press[Find] key can open the ”Find” window like above.
You can press[Up/Down/left/right]key to move highlight and
press [OK] key to input the selected symbol or letter into the
dialogue.
2. After input each character, the program list on the left will
search the channel according your input, and list the matched
channel.
Page 19
USER’S MANUAL
19
3. Move highlight to ”OK” and press [OK] key can close ”Find”
window and you can select channel from the channels list
directly.
9.2 ORGANIZING FAVOURITES
This menu is helpful in adding and deleting services to and from
the favorite group.
1. FAV List
To choose the FAV List by press ”FAV” button.
2. Add
To add services into favorites, Mark the desired services by
press ” OK ” button in Service List, press ► to choose Add
mode and press ” OK ” button.
3. Remove
To remove services from favorites, Mark the desired services by
press ” OK ” button in Favorite List, press
mode and press ” OK ” button.
4. Move
You can reorder and move the service to the preferred position
in Favorite List.
5. Rename
Select the desired FAV List by press ”FAV” button, using
buttons to choose Rename mode and press ” OK ” button to
display keyboard, and rename it.
6. Group, Options and Find functions
Please refer to the ”Organizing Services” part in this manual.
10. INSTALLATION
1. Press [Left/Right] key to select menu pages among Satellite
Installation,FastScan Satellite,Auto installation,Satellite
Guide,Terrestrial Install,Cable Installation.
2. Press [OK] key to enter the ”Installation”. If Menu Lock is
”On”, it will display an dialogue for user to key in password.
The default Password is ”0000”.
◄
to choose Remove
◄/►
3. Press [Up/ Down] key to select menu items. Press [menu]
key to go back to main menu.
10.1 SATELLITE INSTALLATION
Satellite
1. Satellite: Press[OK]key to enter the Satellite list.
2. Press [Up/ Down] key to select satellite. Press [Page] key to
page up or page down.
LNB Type
In this item, press[Left/Right]key can switch among ”Standard”,
”User” and ”Universal” , ”Unicable” mode.
DiSEqC
,
DiSEqC: You can press [OK] and [Up/ Down] key to switch
options. There are several options for your selection:
Page 20
20
USER’S MANUAL
a) Disable: without DiSEqC.
b) 1/2, 2/2: two ports DiSEqC
c) 1/4, 2/4, 3/4, 4/4: 4 ports DiSEqC
d) 1/8, 2/8… 8/8: 8 ports DiSEqC
e) 1/16, 2/16….16/16: 16 ports DiSEqC
Positioner
Positioner In ”Positioner” item, you can press [Left/Right]key
to switch ”Off / DiSEqC 1.2 / USALS” functions.
22K
You can use [Volume Up/ Volume Down] key to switch ”ON /
Off”. When this item is switched to ”ON”, receiver will receive TV
and radio input signal from 22K port. If the item is switched to
”Off”, the receiver will receive all signal from 0K port.
! Notice: When you choose LNB type ”Universal”, you can not
modify 22K.
Polarity
In ”Polarity” item, [Left/Right]key to switch ”Auto / H / V” functions.
LNB Power
In ”LNB POWER” item, you can press [Left/Right] key to switch:
” On/Off” functions.
TP Edit
When you enter to ”TP Edit” menu, there will display the screen
like below:
5. In the ”TP Scan” item, press [Exit] key to exit the scanning
and save the current parameters.
Single Scan
1. Press [Red] key, it will show up a dialog to ask you scan
mode (means you want to scan all channels or only scan
free channels), program type (means you want to scan all
channels or only scan TV/Radio channels), scan type (means
preset scan, that is searching the existed TP. Automatic
Scan means blind scan. It is no need existed TP info) and
NIT Search on/off. After you set up, press [OK] key to start
scanning.
2. Press [White] key into the blind scanning immediately.
TP Scan
Press [Green] key to scan current TP’s programs.
Auto DiSEqC
Press [Blue] key to run Auto DiSEqC function, it can find the
satellite connect to which port automatically.
Blind Scan
Press [White] key can directly into blind scan mode to scan the
current satellite.
10.2 FASTSCAN SATELLITE
In this menu, you can search the channels fast by select the
provider and press OK button on Start Search item.
1. In ”Satellite” item, press[Left/Right]key to switch satellite that
you want to scan or press[OK]key to enter satellite list for
selection.
2. In ”TP Index” item, you not only can use [Left/Right]key to
select transponder but also can use [Add] and [Delete] functions.
• When you press[Green] key, it will display ”New TP” in ”TP
Index” item; You should set the parameters of ”TP Frequency”
and ”Symbol Rate” for this new transponder. The parameters of ”TP Frequency” and ”Symbol Rate” can set by number keys. The available range are ”3000~13450 MHz” and
”1000~45000Ks/s”.
• When you press[Yellow] key, there will show up a warning
message for reminding whether you will delete the current
transponder or not. If you select ”Yes”, the current transponder
will be deleted, and the total account of transponder will
reduce 1 correspondingly.
• When you press [Blue] key, there will show up a warning mes-
sage for reminding whether you will delete all transponders or
not. If you select ”OK”, all transponders will be deleted.
3.
For the existed transponder, you also can use number keys to
modify the parameters of ”TP Frequency” and ”Symbol Rate”.
4. When you complete your modification, Press [Red] key, it will
show up a dialog to ask you scan mode, program type, scan
type and NIT Search on/off. After you set up, press [OK] key
to start scanning.
10.3 AUTO INSTALLATION
”Auto Installation” is a very new and convenient function. It will
automatically detect all dishes connecting to this machine and
scan the available services belonging to the satellite matched
according to satellites and transponders data in current database. You don’t have to input any parameter of your antenna
settings. Just press ” OK ” button to enter this ”Auto Installation”
menu then it starts scanning and shows you the result at the
end of scanning.
10.4 SATELLITE GUIDE
When you enter to ”Satellite Guide” menu, you will see the
screen like below:
Page 21
USER’S MANUAL
21
3. band is VHF and region is ”France”, the range of Ch No. is
from 1 to 9. (it’s according to region)
4. Press [Red] key to enter blind scan menu, or press [Green]
key to enter TP scan menu.
5. Press [Exit] key to exit the scanning.
10.6 CABLE INSTALLATION
Press [OK] key to enter the selected item.
”Satellite Guide” is use for user to enter local longitude; local latitude and satellite longitude. By the evaluation from the receiver
evaluate the antenna azimuth and antenna elevation; user can
follow this guidance to adjust antenna.
1. You can use number keys to input parameters in ”Local
Longitude”, ”Local Latitude” and ”Satellite Longitude”.
2. You can use [Left/Right] key to select east or west in ”Local
Longitude” and ”Satellite Longitude”, select north and south
in ”Local Latitude”.
3. Moving highlight to ”Start” item and press [OK] key. The lower
column on the screen will calculate the corresponding value
automatically.
4. Orientation means the angle between south and satellite.
5. Press [Exit] key to draw back to ”Main” Menu.
10.5 TERRESTRIAL INSTALLATION
Press [OK] key to enter the selected item.
1. You can select the Bandwidth according different country.
2. You can set the Tuner Power ON/OFF.
3. Press [Red] key can directly into blind scan mode to scan the
current programs.
4. Press [Green] key to enter the following menu.
1. You can select the Scan Mode, Manual Scan or Blind Scan.
2. You can input the Frequency by use the numeric button of
the RCU.
3. You can input the Second Frequency by use the numeric button of the RCU, if you set the Scan Mode to Blind Scan.
4. You can input the Symbol Rate by use the numeric button of
the RCU.
5. You can select the QAM value among 16QAM, 32QAM,
64QAM, 128QAM and 256QAM.
6. You can turn ON or OFF the NIT Search, if you set the Scan
Mode to Manual Scan.
7. When you complete your modification, press OK button on
Search item to enter Scan menu and then.
8. press OK button, it will begin to scan.
11. SYSTEM
When you enter to ”System” menu, you will see a screen like below:
In ”System” menu:
1. Press[Left/Right]key to select menu items.
2. Press[OK]key to enter the selected item.
11.1 LANGUAGE
When you enter to ”Language” menu, you will see the screen
like below:
Scan Mode
1. There are two modes. You can scan channel bychannel or
by frequency”.
2. When scan band is UHF and region is ”France”,the range of
Ch No. is from 21 to 69. When scan
Page 22
22
USER’S MANUAL
1. Language: press [Left/Right] key to select menu languages, the selections of languages include: French, English,
Spanish,Russian, German, Greek, Italian, Portuguese,Arabic,
Polish. etc.
2. First Audio: Some channels have more than one audio
language for choosing; by this function you can set the first
audio for this channel. If the playing channel has the same
audio as the ”First Audio” you set, system will play this
audio language as default. If the channel hasn’t the suited
audio language, then the system will compare automatically
with second audio language. The selections of audio languages include: English, French, German, Russian, Arabic,
Portuguese, Turkish, Spanish, Polish and Italian.
3. Second Audio: If the channel has no correspond audio with
”First Audio” but have corresponded audio with ”Second
Audio”, system will play the second audio language as
default. If no audio language corresponds with the ”Second
Audio”, then the default language of current channel will
be played automatically. The selections of audio languages include: English, French, German, Russian, Arabic,
Portuguese, Turkish, Spanish, Polish and Italian.
4. Audio Priority: Press [Left/Right] key to select Dolby or
Language.
5. EPG: Press [Left/Right] key can select EPG language.
6. Subtitle Language: Press [Left/Right] key can select subtitle
language.
7. Teletext: You can set teletext language. If the streams have
this language you can see the teletext in language you set.
8. Press [MENU] key to draw back from ”Language” menu.
11.2 A/V CONTROL
When you enter to ”A/V Control”menu, you will see the screen
like below:
and 4:3 picture source will be too wide in a 16:9 TV but will be
good display in a 4:3 TV.
• Digital Audio Out is for setting the both SPDIF and HDMI’s digitl audio output mode, it has options LPCM Out, Auto, You can
press [Left/Right] Key to select each mode circularity. LPCM
Out means system will decode no matter AC3 or PCM audio
track data to be LPCM, digital audio decoder or HD TV will get
LPCM digital audio data. Auto means system will detect which
the connected HD TV can decode and then output that data. If
HD TV can decode AC3, system just output RAW data, if HD
TV can decode LPCM only, system will just decode AC3 or
LPCM to be LPCM and then output.
• Service Switch Mode: Press [left/right] button to select unblank
or blank.
• Brightness/Contrast/ Saturation : You can adjust the parameter about the Video image by using the [OK]button or
press[Volume Up/Volume Down] key, the default value is
Level 10.
• Press [MENU] key to draw back from ”A/V Control” menu.
11.3 ETHERNET SETTING
1. Select your Network Type as Wired or WirelessUSB 3G
Dongle, if you select Wireless, can configuring Wi-Fi (wireless) as the following step:
a) Select Wireless on Default Network Type item.
b) Press [red] button the wireless LAN network list will appear,
Select you Wi-Fi network and press [ok] button, at last input
password.
Display Mode is for switching the system outputting video
resolution. Move highlight on it and press left or right key, it will
switch video resolution circularly by the sequence ”AUTO”, ”By
Native TV”,”480p”, ”576P”, ”720P_50”,”720P_60,”1080i_50”,”
1080i_60” ,” 1080P_50” and” 1080P_60”This effect is equal to
press V.Format Key under Full Screen and their last setting saving will be efficient for each others. By Source means system
will set the video output resolution according to the program
it’s playing, different resolution programs switching perhaps will
makes TV screen flickering. By Native TV means system will
be according to the HD TV’s max supported resolution to set its
resolution, if system is not connected to a HMDI TV, it will set
resolution to be default
• Aspect Mode is for switching the screen aspect ratio mode.
Now we provide below options: 4:3 PS / 4:3 LB / 16:9/Auto.
You can press [Left/Right] key to select each mode circularly.
16:9 will provide user pillar box mode it means user use 16:9
TV to display but need to see a 4:3 full display picture. System
will force press wide screen picture to be narrow and there’re
black band on left and right site. Auto means system won’t
do any aspect ration translation, 16:9 picture source will be
good display on a 16:9 TV but will be too narrow on a 4:3 TV,
c) Press [OK] button on Connect item to start connecting.
2. this menu you may assign a dynamic IP address to the digital
receiver. To do so, select the DHCP On.
3. If you have a static IP address, unselect the DHCP Enable,
Page 23
USER’S MANUAL
23
then the IP Address, Subnet Mask, Gateway and DNS
options become enabled. You have to set these options
according to your IP address.
4. WiFi Manager
Insert WiFi equipment first, then search available Enter net
signal, input the password to connect with network.
5. 3G Network
a) When you inset the 3G dongle, the screen will display a mes-
sage like ”3G Device plug in ”after 14 seconds and will auto
connect 3G Network. you will see picture like the below.
b) In this menu,you can press [OK] key select 3G Dial setting,
Press [OK] key to select connect to network or disconnect
the network
11.4 TIME SETTING
When you enter to ”Local Time Setting” menu, you will see the
screen like below:
11.5 TIMER
Press [OK] key to open timer menu.
• Current time information will display on the first column; if the
current time is incorrect, please modify the time information in
”Time” item.
• Timer Number: You can press [Left/Right]keys to set Timer
number, and there are 8 timers in total.
• Timer Mode: There are several modes for Timer to setting,
include Off, Once, Daily, Weekly and Monthly .
• Timer Service: There are two options for ”Timer Service”,
include ”TV Channel” and ”Radio Channel” (timer setting for
channel change and Wakeup/Sleep) and ”Record Radio” and
”Record TV” (Timer setting for Record the TV or Radio program to USB Hard Disk) and Message (reminding message).
• When you select ”Channel” (timer setting for channel change
and Wakeup/Sleep) option in ”Timer Service”, the screen will
display like below:
I. Channel: press [OK] key to enter channel list and select chan-
nel that you want to setting.
II. Date: use number keys to input your wakeup date.
III. On Time: use number keys to input your wakeup time. Once
the time’s up, no matter what the system is in standby mode
or in playing mode, the system will automatically switch to
the channel you want and start to play.
Duration: After you set a time for ”Duration” item, once the
IV.
time’s up, the system will automatically switch to standby mode.
If you want not work this function, set the duration is 00:00.
• When you select ”Message” (reminding message) option in
”Timer Service”, the screen will display like below:
• GMT Usage: This item is use for open the usage of GMT. You
can press [Left/Right]keys to switch ”On/Off”.
• The ”GMT Offset” item is valid only when the setting of ”GMT
Usage” is ”Yes”. You can press[Left/Right]keys to switch ”GMT
Offset” value, and the range is ”-12:00 ~ +12:00”, increase
each half hour progressively.
• You can press [Left/Right] to control Summer time on or off.
• ”Date” and ”Time” items are valid only when the setting of
”GMT Usage” is ”No”. You can press [Left/Right] keys to moving highlight and use number keys to input directly.
• Press [MENU]key to draw back from ”Local Time Setting”
Menu.
V. Wakeup Message: press [Left/Right] key to select reminding
message as Birthday, Anniversary and General.
VI. Date, you can use number key to input your wakeup date.
VII. On Time: use number keys to input your wakeup time.
Once the time’s up, no matter what the system is in standby
mode or in playing mode, the system will automatically pop
a reminding message.
VIII. The message will always display on the screen, you can
press [Exit] key to close it.
IX. Standby After Finish: You can press [Left/Right] to control
the system is in standby mode or in playing mode after the
record stopped.
X. Extend Record Time : Press [left/right] button or input the
number using numeric keys to set the Extend Record Time. It
is used to add time at beginning and end of the record time.
Page 24
24
USER’S MANUAL
XI. Press [MENU] key to exit the current menu.
11.6 PARENTAL CONTROL
1. You can set a password for anyone who wishes to operate in
the ”Installation” menu. And you can also set the password
for the lock channels. (How to set the lock channel please
refer to LOCK) Here will show you how to setting and how to
revising the password.
2. In ”Parental Lock” function, press [OK] key, there will pop an
dialogue for you to input the password. When you input the
correct password, you will see a screen like below:
3. Menu Lock determining that when user wish to enter
”Installation” menu, whether have to input Password or not. If
the setting of ”Menu Lock” is ”On” which means user have to
key in password, set ”Off” means unlock.
4. Channel Lock determining that when user wish to play the
lock channels, whether have to input the password or not.
If the setting is ”On”, play the channels with lock mark will
show up a dialogue on the screen and ask for the password.
If the setting of ”Channel Lock ”is ”Off”, the Lock function will
invalid.
5.
New Password is used for revising password; you can input
the new password in this item by using number keys directly.
After you filled in 4 digital numbers, the highlight will auto skip
to Confirm Password and ask you to input the new password
again. If the password is correct, the screen will show up a message of ”Saving Data, Please Wait…”. After finish saving and
draw back to ”System Setup” menu, the revising is complete.
6.
Press [MENU] key to draw back from the ”Parental Lock” menu.
11.7 MISCELLANEOUS SETTINGS
When you enter to ”Miscellaneous Settings” menu, you will see
a screen like below:
Watt. if it’s set to ”Fake” ,Press power key, receiver will be in
fake standby status.
4. OSD Timeout: When you switch channels in full screen, there
will show up some information about current channel on the
lower of the screen. And regarding to the duration of these
information show up on the screen, you can press [OK] and
[up/ down] key to set the time. The range of the duration is ”1
second ~ 10seconds”.
5. OSD Position: control display position of the info bar in full
screen mode. You can choose ”bottom” or ”top”.
11.8 SOFTWARE UPGRADE
11.8.1 Upgrade By USB
In this menu you can upgrade the software from USB conveniently, Press ”Left/Right” button select USB A or USB B; press ‘
OK ‘ button to enter.
In this menu you can select the Upgrade Mode among
Software(No channel list), Channel list, All SW+bootloader
and All SW+Channel list, and you can select the appropriate upgrade file on ”Upgrade File” item. After you select the
”Upgrade Mode” and ”Upgrade File”, press ‘ OK ‘ button on
”Start” item, the receiver can upgrade automaticlly
Note: You must put the upgrade file on the /ROOT DIRECTORY
of the USB storage.
11.8.2 Http Upgrade
1. Subtitle Auto: You can press [Left/Right] key to select ”On”
or ”Off”. If the current channel has subtitle information, it will
be showed up automatically while this function is ”ON”, if this
function is ”OFF”, you need turn on the subtitle manually by
press [SUBTITLE] key.
2. Auto Power Down: You can press[Left/Right] key to select the
time or ”Off”, if you select time, duration this time if no any
operation on receiver, it will go to standby mode.
3. Standby mods: if set to ”Real”, Press power key receiver will
be in real standby status, the consumption will less than 0.5
When connected to the Internet, receiver can manually or automatically make software update from file from server.
Note: This function depends on connection with external server.
In case of no software on server, this function will not work.
Page 25
USER’S MANUAL
11.8.3 Ftp Upgrade
25
When connected to the Internet, receiver can make software
update from file from FTP server.
Note: This function depends on connection with external server.
In case of no software on server, this function will not work.
11.8.4 Upgrade by RS232:
1. We offer the functions for user to connecting receiver
(Master) to the other receiver (Slave) via serial interface.
Connect master receiver to slave receiver via serial interface. Enter ”Software Upgrade” menu in master receiver and press[left/right]keys to switch upgrade mode All
SW+bootloader /All SW+Channel list/Software(no channel
list)/Channel list.
2. Moving highlight to ”Start” on master reeciver and press[OK]
key to start upgrade.
3. Turn on slave receiver and it needn’t operate any setting.
4. Press [Exit]key to draw back.
11.8.5 Backup to USB
This function can upgrade the software through signal lines from
the satellite
1. Select the satellite and TP or input the TP value and download PID, these parameters you can get from your provider.
2. Then move the highlight to the start button and press [OK]
button to start upgrade.
b) Upgrade By Terrestrial:
This function can upgrade the software through signal lines from
the Terrestrial
1. Select or input the Frequency, Bandwidth and download PID,
these parameters you can get from your provider.
2. Then move the highlight to the start button and press [OK]
button to start upgrade.
c) Upgrade by Cable
This function can upgrade the software through signal lines from
the cable.
In this menu ,you can dump the software to the USB equipment
1. In ”Backup file”,you can press [OK] key to edit the file name.;
Press ”Left/Right” button select USB A or USB B;
2. In ”Backup to USB”, you can press [OK] to start backup
software.
a) Upgrade By Satellite:
1. Input the frequency, symbol rate value and download PID,
and select scan mode.
2. Then move the highlight to the start button and
3. press [OK] key to begin to upgrade.
11.9 DEFAULT SETTING
Page 26
!
26
11.9.1 Default Value
When you press [OK] key In the ”Default Setting” item:
1. There will pop a dialogue for you to enter the password, and
the default password is ”0000”.
2. After you input the correct password, there will show a warn-
ing message to inquiry you ”The operation will load default
and erase all the channels that user added, continue?”.
3. If you select ”OK” option, the all revised parameters of the
receiver will reset to default value. Please carefully to using
this function.
4. In step 1 and step 2, press[Exit]key can draw back from this
item and without saving.
11.9.2 Delete All Channel:
USER’S MANUAL
2. Press [MENU] key to draw back to ”System” menu.
12. CONDITIONAL ACCESS
12.1 CA SETTING
We provide one CA slots for user to use. Receiver has build
in smart card module with CONAX system. By using cards in
this system provided by operators, it is possible to watch many
scrambled channels coded in this system. This menu shows
detailed information about cord inserted into cord reader module. It allows inserted according to help messages visible on the
bottom of the screen.
When you press [OK] key in the ”Delete All Channel” item, it will
pop a dialogue ask you whether confirm to delete all channel. If
you select ”OK”, all the channel will be deleted.
11.9.3 Save default value
Note: All information showed in this menu and submenu are
coming from inserted card. In case if anything is wrong, it could
be card problem. After inserting the card correctly at any time,
a message-box will show on the screen with message about
detecting the card, in ”card info” menu all available information
will be displayed. You can press [left/right] key to set the message display time.
When you press [OK] key in the ”Save default value” item,there
will show a message to inquiry you”Do you want to set current
database as default data?”.If you select ”OK” option,it will to set
current data as default data
11.10 INFORMATION
1. When you enter to ”Information” menu, you will see a
screen like above. The screen displays: MODEL ID,S/W
VERSION,H/W VERSION, LOADER VERSION, LATEST
UPDATE, STB SN.
12.2 COMMON INTERFACE
Page 27
USER’S MANUAL
We provide two CI slots (option, some model only has one
slot) for user to use. Using different CAM & cards provided by
different CAS operator, user can view many type or scrambled
channels.
We provide this menu to display the detail information of the
CAM & cards inserted in the slots. User can check all this information according to the help message at the bottom of each
menu.
Note: All information showed in this menu and submenu is
abstract from CAM & card. In case something is wrong, it may
be the problem of CAM or card.
When you insert the CAM correctly at any time, a message
will show in the screen to tell you that which CAM has been
detected by the receiver and is available now.
CI Message
It is used to turn on or turn off the CI info display function by
using
◄/►
ON: To display the CI info.
OFF: Don’t display the CI info.
13. MEDIA
if you enter to the ”Media” Menu, you will see the picture like
the below.
Note: If no USB Hard Disk insert to the receiver this menu is
not available.
buttons or ” OK ” button to select.
27
You can see the video files in this menu, it can support .mpeg
and .ts format file.and press [play] key, you can preview the
video at the top right corner.if you want to watch the video in full
screen you can press [OK] button.
You can press [1] key to adjust the volume while you preview
the video file,press [0]key to sort the file list. and press
enable or disable the audio
• Yellow key
To edit the files or folders. Include rename, copy, delete and create folder function. You can press [Exit] key to previous menu.
13.3 MUSIC
In this menu you can press [left/righ] button to select the USB
disk that you want to visit. Then Press [ok] button to enter the
music list
to
13.1 RECORD
In this menu you can playback the record files, and you can
press [Red] key to rename the file, or press [Green] key to lock
the file, or press [Yellow] key to delete the file.
You can press [1] key to adjust the volume while you preview
the record file on top of the right corner .and you can press
to enable or disable the audio.
13.2 MOVIE
In this menu you can press [left/right] button to select the USB
disk that you want to visit. Then Press [ok] button to enter the
Video list.
In this menu you can select the MP3 file to play by press [OK]
key or [PLAY] key. Also you can setting the play list..
[Red] key: Show play list as the picture bellow:
• Red Key:
Move the selected file by press Red key and [UP][DOWN] key.
• Green Key:
Delete the selected file by press Green key.
• Yellow Key:
Delete all the file by Yellow Key, but there is one remind ”Delete
All” before practical operation, if select Yes, all file will be deleted, and close the Play list window.
• Press OK button to play file.
[Green] key:
All the MP3 files in current directory are added into MP3
play list by press [Green] key, and will display ”
MP3 files.
” behind the
Page 28
28
USER’S MANUAL
[FAV] key: To add mp3 or jpeg to play list.
13.4 IMAG E
In this menu you can press [left/right] button to select the USB
disk that you want to visit. Then Press [ok] button to enter the
Image list.
[Yellow] key:
To edit the files or folders in the USB storage.press this button
you can see the picture like the below.
• Red Key
To rename the file or folder.
• Green Key
To copy the file or folder to other folder.
• Yellow Key
To delete the file or folder from the disk.
• Blue Key
To create a new folder in the disk.
Press [EXIT] key to draw back to ‘EDIT’ MENU
[White] key:
To setting the Repeat mode of the MP3 player.
Press ‘OK’ button on the selected files to play the files.
You can preview the picture at the top right corner if the scroll
bar is on the picture files (JPG, BMP).
Move scroll bar when press up/down key, page up or down by
page key.
Go into sub-directory when press ok key in the file directory,
play the selected file when scroll bar is on the file, automatic
return USB menu after play is over.
13.5 PVR SETTING
After begin to play MP3, it will show the MP3 play window.
Press ”PAUSE” button to pause.. Press ”PLAY” button to play.
Press ”STOP” button to stop and time return to 00:00.
Press ”PREV” button to jump to the beginning of file list if play
is over 3 seconds; or jump to previous file if play less than 3
seconds.
Press ”NEXT” button to go to the next file.
Press ”FORWARD” button to forward 4S. Press ”BACKWARD”
button to back 4S. Jump to beginning or end if less than 4S to
the beginning or end of music file.
Switch to the next file or stop playing by the repeat mode when
play is over on the current file.
[0] key: To sort the file list by different order.
1. Time Shift:
ON: Enable the Time Shift function.
OFF: Disable the Time Shift function.
2. Timeshift to Record
ON: Means when you press the ”
gram, it will merging the Timeshift files and the record files.
OFF: Means when you record the program, it just start when
you press ”
3. Record as Scrambled
4. Record Type
You can select the record type by press [left/right] key.
5. Jump Step
You can select the jump time by press [left/right] key.
6. Record Path
You can select the record path by press[left/right] key.
●
” button, not include the Timeshift files.
●
” Button to record the pro-
Page 29
USER’S MANUAL
29
7. Timeshift Path
You can select the timeshift path by press[left/right] key.
13.6 DISK MANAGE
In this menu you can select USB disk for HDD Format,HDD
information and USB Speed test.
HDD Format
Press ”Green” button to enter the HDD Format menu like the
below picture.If you want to format the HDD then select the File
System between the ”FAT” and the ”NTFS”, Press ”OK” Button
to confirm.
HDD Information
operation your disk can support..In this menu,and you can press
”Red” button refurbish the USB disk speed.
13.7 REMOVE USB DEVICE SAFELY!
Use this menu you can remove the USB Device safely.
14. APPLICATION
If you enter to the ” Application ” Menu, you will see the picture
like the below:
14.1 YOUTUBE
This menu is some internet applications. ”youtube” can play
stream media from ”www.youtube.com”. When you enter this
menu, you will see a screen like below:
Press ”Yellow” button to enter the HDD Information menu like the
below picture, you can see details information about the HDD.
USB Speed Test
Press ”Blue” button to enter the USB Speed Test menu like the
below picture, you can see the Standard speed and your USB
harddisk speed, according this information you can know what
1. Press [up/down] key to move highlight.
2. Press [ok] key on one item, it will play pertinent video. The
video will show on top left corner. Press [ok] again, it only
Page 30
30
shows video in the centre of your screen. Now press [zoom]
key, the video will play in full screen.
3. Press [vol+/vol-] to control volume.
4.
Press [pause] key to pause video, or press [stop] key to stop play.
5. Press [red] key to display the featured video.
6. Press [green] key to sort by site and duration. The site has
Germany, worldwide, Poland and so on. Duration has all
time, this week, this month and so on.
7. Press [yellow] key to switch group. These are game, news,
tech, move and so on.
8. Press [blue] key to display the top video. These are top
favorites, top rated, most views, most recent and so on.
9. Press FIND [
You can press [
press [ENTER] key to input the letters .
14.2 RSS READER
] key in full screen to open the ”Find” window.
◄/►,▼/▲
] keys to move highlight and
USER’S MANUAL
In this menu you can see the weather forecast, press [Green]
key to add city.
In this menu you can see the news
• Red key
To update the news to the newest.
• Green key
To add new channels,you can input a new website.use this
menu.you can add 10 channels at most.
• Yellow key
To delete current channel.
• Blue key
To edit current channel information.you can edit channel name
and channel Url.
Press ok button to see the detail infomation.like the below.
14.3 WEATHER FORECAST
• Red key
To update the weather forecast to the newest.
• Green key
To add new city.use this menu.you can add 5 cities at most.
• Yellow key
To delete current city.
• Blue key
To switch other temperature mode.
14.4 GOOGLE MAPS
Inside the menu can browse Google Maps
14.5 FTP
When connected to the Internet, receiver can download some
files, such as software, MP3 or Image files from FTP server.
Note: This function depends on connection with external server.
Page 31
USER’S MANUAL
31
In case of no any files on server, this function will not work.
14.6 WEB T V
When you enter to ”Web TV” menu, you will see a screen like
below:
1. In this menu you can select your favorite channel to view,
press [OK] key play in full screen, you can press [up / down]
key to change channels, and press [left / right] key or [volume
+ / -] key to adjust volume level.
2. Press [green] key to add channel URL;
3. Press [blue] key to edit channel URL;
4. Press [yellow] key to delete channel URL.
5. If you get the ”WebTV List.txt” file, you can add more channels and press [white] key to update the channels from USB.
15. EPG
Press ‘OK’ button to this menu you can see the picture like the
below, you can select EPG more and Schedule.This Function is
same as EPG.
1. You can press ”II” button to pause the video.
2. You can press ”
Forward.
3. You can press ”
Slow Forward.
4. Press ”left” or ”right” button to jump to different position, then
press ”OK” button to confirm.
5. Press ”
16.2 RECORD
If you connect the USB HDD.
You can press ”
picture:
◄◄
” or ”►►” button to Fast Backward or Fast
◄I
” or ” I►” button to Slow Backward or
” button to exit the playback.
●
” button to start record function, as following
1. Press ”►” button to display the record info bar when you
recording.
●
2. Press ”
” button again to setting the record time.
16. NEW F EATURES
16.1 TIME SHIFT
If you connect the USB HDD, and enable the Time Shift function
in the menu ”Main Menu/ Media/ PVR Setting/Time Shift”,
It will start the Time Shift function automatically after you switch
the program, and when you press the ”Tms” button the Time
Shift info bar will displayed as the following picture:
3. You can press ”II” button to pause the video.
4. You can press ”
Fast Forward.
5. You can press ”
Slow Forward.
6. Press ”left” or ”right” button to jump to different position, then
press ”OK” button to confirm.
7. Press ”
◄◄
” or ”►►” button to Fast Backward or
◄I
” or ” I►” button to Slow Backward or
” button to stop the recording.
Page 32
32
USER’S MANUAL
17. TROUBLE SHOOTING
If you suspect there is a fault with your receiver, please check the following trouble shooting guide before calling authorized service
agent. Warning! Under no circumstances attempt to repair the receiver yourself. Tampering with the receiver may result in fatal
electric shock and will invalidate your warranty.
SYMPTOM POSSIBLE CAUSE
Settings you made in the menu have not change.
No signal.
Receiver is on but no picture or sound except the
following messages (NO TV program)
Receiver not responding to remote control unit. RCU batteries are dead or inserted incorrectly. / The RCU is pointing toward wrong direction.
Poor picture Quality. The level of Signal strength is low.
No sound. The cable is connected incorrectly. / The Volume level is low. / Muting function is active.
No display on the LED Display Panel. The power cord is not plugged in correctly.
No picture on the screen.
The receiver lost power before being able to enter into standby mode. / Some of the Settings
saved by user can be deleted partly or fully.
The level of signal is weak. / LNB is out of order. / The cable from the LNB is incorrectly
Connected (short circuit or open circuit). / The position of dish is aligned incorrectly.
Channel is not available. / Channel is scramble.
Receiver is in Standby mode. / RCA Jack or cable is not connected firmly to the video output port
of television. / Incorrect channel or video output is selected on television. / Brightness level of
your TV set is incorrectly defined.
18. SPECIFICATIONS
SYSTEM RESOURCES
Main Processor. . . . . . . . . 594MHz based CPU
Flash Memory. . . . . . . . . . 16 Mbyte
DDR SDRAM . . . . . . . . . . 256 Mbyte
TUNER/FRONT-END(OPTIONAL)
Tuner Type . . . . . . . . . . . . DVB-S / DVB-S2
Input Connector . . . . . . . . F-type, Connector, Female
Signal Level . . . . . . . . . . . -65 to -25 dBm
LNB Power & Polarization
Horizontal: +18V
Current: Max. 400mA
Overload Protection
22KHz Tone . . . . . . . . . . . Frequency: 22±1KHz
DiSEqC Control . . . . . . . . Amplitude: 0.6±0.2V
Version 1.0, 1.1 1.2, USALS
Demodulation . . . . . . . . . . QPSK, 8PSK
Input Symbol Rate . . . . . . 1-45 Mbps, Convolution Code Rate
Forward Error Correction (FEC)
DVB-S2 1/2, 3/5 , 2/3, 3/4 ,4/5 , 5/6,
8/9 , 9/10
Tuner Type . . . . . . . . . . . . DVB-T2/T/C
Input Connector . . . . . . . . IEC-type, Connector, Female
Frequency Range. . . . . . . 47MHz~862MHz
Input Level . . . . . . . . . . . . -82.0dBm and -20.0dBm
Active ANT Power. . . . . . . DC 5V at max 75 mA,
Overload protection
Bandwidth. . . . . . . . . . . . . VHF/UHF: 6MHz, 7MHz, 8MHz
Demodulation . . . . . . . . . . COFDM
Transmission mode(FFT) . 1k, 2k, 4k, 8k normal and extended,
Constellations. . . . . . . . . . QPSK, 16-QAM, 64-QAM, 256-QAM
Both rotated and non-rotated
Guard intervals . . . . . . . . . 1/4, 19/256, 1/8, 19/128, 1/16, 1/32,
Code rate . . . . . . . . . . . . . DVB-T: Viterbi + Reed
Scattered Pilot Pattern . . .
DVB-T2 Input Profiles. . . . Input Mode A-Signal PLP, input
. . Vertical: +13V
Available, Unicable
. DVB-S 1/2, 2/3, 3/4 5/6, 7/8
16k normal and extended, 32k normal and extended.
1/128
Solomon 1/2, 2/3, 3/4, 5/6, 7/8.
DVB-T2: LPDC + BCH 1/2, 3/5, 2/3,
3/4, 5/6.
PP1, PP2, PP3, PP4, PP5, PP6, PP7, PP8
Mode B-Multiple PLPs(Common
PLP, Type 1 and 2 up to the maximum allowed figure 255)
POWER SUPPLY
Input Voltage. . . . . . . . . . .
Power Consumption . . . . . 20W MAX
Free Voltage (100~240V AC, 50/60Hz)
MPEG TS A/V Decoding
Transport Stream . . . . . . . MPEG-2, H.264
Input Rate. . . . . . . . . . . . . Max.120Mbit/s
Aspect Radio . . . . . . . . . . 4:3, 16:9, Letter Box
Video Decoding . . . . . . . . MPEG-2, MP@ML, MPEG-4 part
Video Resolution . . . . . . . 720*480P/I, 720*576P/I, 1280*720p,
Audio Decoding . . . . . . . . MEPG-1 layer I/II, Mpeg2 layerII,
Audio Mode . . . . . . . . . . . Left / Right / Stereo/ Mono
Sampling Rate . . . . . . . . . 32, 44.1 and 48KHz
10/H264
1920*1080i, 1920*1080P
Dolby digital
A/V & DATA INPUT/OUTPUT
AV OUT . . . . . . . . . . . . . . Video CVBS output
Audio L/R output
IR . . . . . . . . . . . . . . . . . . . 38Khz
RS-232 . . . . . . . . . . . . . . . Transfer rate 115.2Kbps
9 pin D-sub Type
LAN. . . . . . . . . . . . . . . . . . 100M
USB . . . . . . . . . . . . . . . . . Two USB 2.0 slot Compatible
HD OUT . . . . . . . . . . . . . . VER1.3
Type A
PHYSICAL SPECIFICATION
Size[W*H*D] . . . . . . . . . . . 220×169×46mm
Net Weight . . . . . . . . . . . . 1.2KG
Operation Temperature. . . 0
Storage Temperature . . . . -10
Storage Humidity . . . . . . . 5%~95% RH (Non-Condensing)
Specifications are subject to change without further notice.
The manufacturer does not assume any responsibility regarding any errors or mistakes in printing. Please note that new
software may change the features of the receiver. The manufacturer holds the rights of changes without any further notice.
The image shown here is indicative only.,The actual product
may differ.
0
C~+450C
0
C~+700C
Loading...