Amico Ceiling Column Motorized Retractable User Manual

Approval and Installation Booklet

Motorized Retractable Ceiling Column

www.amico.com

Table of Contents

Product Description 3

Cleaning 3

Inspection and Testing 3

Range of Column Retraction 4

Device and Accessory Chart 5

Device Placement (Bottom View) 6

Electrical Diagram (Bottom View) 7

Riser Plate to Outlet Detail 8

Termination Box 9

Riser Pipe Assembly 10

Mounting of the Ceiling Column 11

Mounting Information 12

Typical Location View 13

Wiring Diagram 13

Remote (Optional) 14

Control Unit 15 - 16

Linear Drive 17 - 18

Servicing 19

*NOTE: Amico requires all pages to be signed and dated before fabrication will begin.

2 Amico Pipeline

Product Description

The motorized retractable ceiling column shall be an Amico Alert-1 series.

The motorized retractable ceiling column shall be of the motorized operated type. The column shall consist of an
upper section for rigid mounting at the ceiling level and a telescopic lower section.

The lower section of the column is activated by a motorized actuator mounted into the internal shell of the column.
With the aid of a wall switch or with a head mounted switch, the column can be raised or lowered to any desired
position. With the aid of an internal tracking system, the movement of the telescoping portion will glide freely up
or down.

The upper and lower section shrouds are made of 16 gauge stainless steel with a # 4 satin  nish and are complete
with: Removable access panel, stainless steel ceiling collar and a heavy gauge steel mounting plate, equipped with
hose assemblies (gas speci c) within the internal shell of the column and brazed type outlets for all medical gas
connections above the ceiling line.

All electrical and medical gas services are provided to the face of the lower section by means of  exible hoses and
conduits. All threaded connections comply with NFPA, CGA and DISS recommendations preventing interchanging
of connections. All services are pre-assembled and factory tested. Standard dimensions are 13.56” x 13.56” [344.5mm
x 344.5mm] for the upper section and 12” x 12” [304.8mm x 304.8mm] for the lower section.

NOTE: Electrical devices are pre-wired, unless otherwise stated.

Cleaning

The Amico Outlets are factory cleaned for oxygen service. Exposed surfaces of the outlet may be cleaned with a mild
detergent solution or wiped with a disinfectant commonly used in patient rooms that is compatible with plastics,
anodized aluminium and die cast zinc.

Inspection and Testing

Medical Gas Outlets should be inspected periodically or at least once a year. The test should be in accordance with
NFPA 99 “Gas and Vacuum systems”, or CSA Z7396.1-06 “Non ammable Medical Gas Piping System”.

Test for leaks: Ensure that no leaks exist, with or without the adapter inserted.
Test for Indexing: Only a mating gas speci c adapter should insert smoothly into the outlet, latch and be retained.
Test for Flow:

- Gas Outlets: 120 l/min (4.2 scfm) @ 345 kPa (50 psi), maximum allowable pressure drop is 28 kPa (4 psi).

- Nitrogen Outlet: 400 l/min (14.1 scfm) @ 1,250 kPa (180 psi), maximum allowable pressure drop is 70 kPa (10 psi).

- Vacuum Outlet: 30 l/min (1.1 scfm) @ 54 kPa (16 inHg), maximum allowable pressure drop is 13 kPa (4 inHg).

Refer to the appropriate standards for the proper way of performing the  ow test.

Note: The Amico medical gas and vacuum outlets meet and exceed these requirements at the time of
manufacture. However piping source capacity, sizing and restrictions may prevent outlets from
attaining these values.

www.amico.com 3

Range of Column Retraction

To accommodate for di erent ceiling heights, Amico Corporation has standardized three di erent variations.

The LOW height is designed for ceilings below 9’ - 0” (2743mm) 10” (254mm) Retraction Only.
The MEDIUM height is designed for ceilings between 9’ - 1” (2769mm) and 9’ - 11” (3023mm) 14 “ (355.6mm) Retraction Only.
The HIGH height is designed for ceilings above 10’ - 0” (3048mm) 18” (457.2mm) Retraction Only.

Please select the nominal column height below that applies to you application.

LOW MEDIUM HIGH

CEILING HEIGHT-LOW

78

1981.2mm]

1625.6mm]

62

108"

[2743mm]

30

762mm]

1117.6mm]

44

114”

[2895.6mm]

CEILING HEIGHT-MEDIUM

78

1981.2mm]

60

1524mm]

36

914.4mm]

1384mm]

54

120"

[3048mm]

CEILING HEIGHT-HIGH

42

1066.8mm]

60

1524mm]

78

1981.2mm]

60

1524mm]

4 Amico Pipeline

FINISHED FLOOR LINE

Approval Signature Date Phone No.

Device and Accessory Chart

*QD

XXX

Ohmeda / Medaes

Compatible

CH

XXX

Chemetron
Compatible

PB

XXX

Puritan-Bennett

Compatible

*DI

XXX

DISS

PE

Ceiling Column

Passive Evacuation

(19mm/33mm)

IMP

Passive Evacuation

with Impedance

V al ve (19mm /2 2mm)

(Side Mount Only)

GJ

Ground Jack

Receptacle

Single Hampden

(SLR-3)
GREEN

GJ2

Ground Jack

Receptacle

Dual Hampden

(SLR-3)
GREEN

E9-RED

E10-IVO.

Duplex Receptacle

8300-HG

125V/20a

(US / International)

E11-RED
E12-IVO.

ngle Receptacle

Si

8310-HG

125V/20a

(US / International)

E5-RED
E6-IVO.

Duplex Receptacle

8200-HG

125V/15a

(CAN / International)

E7-RED
E8-IVO.

Single Receptacle

8210-HG

125V/15a

(CAN / International)

E13-RED

E14-IVO.

TL

Oxequip

Compatible

SL

OX

XXX

Monitor Jack Duplex

(5-pin shown)

Amphenol Model

10-825806-05S

97-14S-5S

IV

MJ

E13C-RED

E14C-IVO.

Ground Fault Circuit

Interrupter

(C = Canadian)

DJ
DP

Vacuum

Bottle Slide

ALL ELECTRICAL DEVICES ARE HUBBELL BRAND

NOTE: CARBON DIOXIDE OUTLETS ARE NOT AVAILABLE IN PURITAIN-BENNETT. NITROGEN OUTLETS ARE ONLY AVAILABLE IN DISS.

NOTE: PASSIVE EVACUATION FOR RETRACTABLE WILL PROVIDE 240” [6096mm] LENGTH OF 0.75” [19.05mm] PVC HOSE FOR CONNECTION IN CEIILNG.

Stai nless Steel

IV Hook

(Duplex only)

Data - Telephone

Communication Jack or

Duplex Receptacle

(Provision Only)

DP - Duplex Receptacle

Provision

Twist-Lock

Receptacle

Hubble 23000-HG

125V/20a

Approval Signature Date Phone No.

www.amico.com 5

Device Placement (Bottom View)

Please fill the devices that you require for your application.
(Specify by using the symbols on Page 5 of this Approval Booklet.)

Is a Local Switch Required?

* if YES, please provide the location (ex. B1)

Yes o

No 

Nitrogen Control Panel

Yes o

No 

Location of Nitrogen Control Panel

Side A

Side B

Side C

Side D

Please Specify Outlet Language

US

CAN

FRENCH

SPANISH/US
SPANISH/ISO

Gas Legend

Oxygen = O

Medical Air = A

Vacuum = V

Nitrous Oxide = 2

Nitrogen = N

Carbon Dioxide = C

WAGD (US) = W

AGSS (Canada) = E

NOTE:

1. Two electrical/communication/medical gas devices cannot be placed together at any corner.

2. Maximum of 12 gas outlets are allowed on the column. If 12 gas outlets are required, then side mount is optional.

3. All electrical devices must be located within section A, B, C, or D only.

4. The Nitrogen Control Panel will occupy three spaces of the bulkhead (E.G. A2 to A4 see Outline).

6 Amico Pipeline

Approval Signature Date Phone No.

Electrical Diagram (Bottom View)

12 gauge

12 gauge

Black

White

10 gauge

Green

*Please Select One of the Following:

Amico recommended circuit schedule based on layout

Custom circuit schedule. Please specify on circuit chart

Receptacle Type:

US/CAN

*BRITISH (simplex only)

*GERMAN (simplex only)

*Please specify electrical details:

Type of wire:

NOTE:

Circuit Chart

THHN XHHW RW90

AWG Wire Gauge: Wire Color:

10 & 12 LIVE/HOT

10 & 12 NEUTRAL

10 GROUND

Isolated Power

Please select one of the following

All receptacles shall be mounted with
ground pin “DOWN”

All receptacles shall be mounted with
ground pin “UP” (Default)

1. Two electrical/communication/medical gas devices
cannot be placed together at any corner.

2. If type of wire & gauge is not specified, Amico
will use the following:

For US/International

LIVE/HOT - 12 Ga. THHN Wire Black
NEUTRAL - 12 Ga. THHN Wire White
GROUND - 10 Ga. THHN Wire Green

For Canada

LIVE/HOT - 12 Ga. RW90 Wire Black
NEUTRAL - 12 Ga. RW90 Wire White
GROUND - 10 Ga. RW90 Wire Green

3. Conduit: 9/16” [14.28mm]  exible metal conduit.

4. All conduits and wires will extend a minimum of12”
[304.8mm] above  nish column for connection
to riser plate.

5. A pull-string will be provided to be connected by
others for all ground jacks and data provision.

6. British or German Receptacle cannot be positioned
side by side ie: A1 and A2.

Approval Signature Date Phone No.

www.amico.com 7

Riser Plate to Outlet Detail C - Riser

VIEW COLUMN

Access Panel This Side

Riser Plate Bottom View Looking Up

17”

[431.8mm]

pipe stub

4.5” [114.3 mm] above

 nished ceiling

anti-sway support

(supplied by others)

17”

[431.8mm]

14.75”

[374.65mm]

For DISS riser pipe
inlet (see page 9)

for column X4

14.75”

[374.65mm]

anti-sway support

(supplied by others)

7/8” [22.2mm] hole X8

1.00”

[25.4mm]

1.00”

[25.4mm]

Mounting holes for
threaded rod X4

1A

see note #4

14.75”

[374.65mm]

Access panel This side

Access Panel This Side

Side A

Access Panel This Side

Side A

C

BOTTOM VIEW COLUMN

Looking Up

BOTTOM VIEW COLUMN

D

Looking Up

Termination X4
box use
see page 10

DISS

for electrical conduit use

X4 See
page 9

2A

BD

BC

NOTE:

1. Riser plate is completed with DISS pipe stubs, typical for each gas (For DISS riser pipe inlet see page 11).

2. Pipe stubs diameters are 3/8” [9.97mm] ID and 1/2” [12.7mm] OD for all gases. Refer to Riser Pipe cut sheet.

3. Exact locations of gas terminations on riser plate will be determined after receiving this booklet.

Approval Signature Date Phone No.

8 Amico Pipeline

Termination Box

Is a riser mounted termination box required? See diagram below

(refer to page 8 for locations).

Ye s (Amico provides termination box - default)

No (Termination box will be supplied by others)

4.773”

[121.23mm]

2 5/8”

[66.68mm]

5 x O .250”

10 - 32
TAPPED HOLE

1 1/2”

[38.1mm]

2 9/16”

[65.09mm]

4”

[101.6mm]

3/4”

[19.05mm]

3/4”

[19.05mm]

3/4”

[19.05mm]

DETAIL A

1 1/4”

[31.75mm]

5/8”

[15.88mm]

[6.35mm]

1/4”

4 - R .344” [R 8.73mm]

4.125” [104.78mm]

.409” [10.39mm]

.061” [1.55mm]

[19.05mm]

1 1/2”

[38.1mm]

0 0

.344” [ 8.74mm]

.376” [9.55mm]

R 1/16” [1.59mm]

1 3/16”

[30.16mm]

2 3/8”

[60.33mm]

4.125”

[104.78mm]

.203” [5.16mm]

4”

[101.6mm]

.629”

[15.97mm]

.394”

[10.02mm]

.188” [ 4.78mm]

0

0

.331” [8.41mm]

[17.09mm]

R 3/16” [17.09mm]

1.47”

[0.058mm]

.188”

[4.78mm]

.673”

.246”

[6.25mm]

8 - 32 UNC - 2B
TAPPED HOLE

DETAIL A

3/4”

1 1/16”

11x 1/2” [12.7mm] KO, RECESSED
2 EACH SIDE, 3 IN BOTTOM

1/4”

[6.35mm]

1 1/8”

[28.575mm]

[26.99mm]

5/8”

[15.88mm]

7/64”

[2.769mm]

17/32”

[13.487mm]

8x 0.171” [4.34mm]
2 EACH SIDE

3/4”

[19.05mm]

6x 3/4” [19.05mm] KO, RECESSED
1 EACH SIDE, 2 IN BOTTOM

NOTE:

1. Maximum of four, Termination Boxes can be mounted on a riser.

Approval Signature Date Phone No.

www.amico.com 9

Riser Pipe Assembly

Ye s (Amico provides termination box - default)

No (Termination box will be supplied by others)

NOTE:

1. “X” represent US/ISO and GAS type
i.e: C-PIPE-CHK-U-AIR

2. 3/8” [9.97mm] ID 1/2” [12.7mm] OD Type “K” Copper
Pipe

C-PIPE-CHK-X-OXY

1/4”

[6.35mm]

(OXYGEN)

CAUTION

Before brazing the Riser an intermittent blow-out purge

*

is required to be done until all debris are cleared from
the Pipeline System.

*

Installations of the Riser should be done in accordance
with current NFPA 99 and CSA Z7396.1.

*

Risers with Demand checks should avoid excess or direct
heat near its brass end.

C-PIPE-CHK-X-XXX (AIR, N2O, CO2, NIT)

C-PIPE-CHK-X-VAC

C-CHKVLV-OXY

3/16”

[4.76mm]

C-CHKVLV-GAS

3/16”

[4.76mm]

C-CHKVLV-VAC

7/32”

[5.56mm]

(AIR, N

0, CO2 & NIT)

2

C-CHKVLV-EVA

1/4”

[6.35mm]

C-CHKVLV-IAR

C-PIPE-CHK-X-XXX (WAGD, AGSS)

(VACUUM)

C-PIPE-CHK-X-IAR

(EVACUATION)

(INSTRUMENT AIR)

10 Amico Pipeline

Approval Signature Date Phone No.

Mounting of the Ceiling Column

There will be four (4) 1/2” - 13 x 8” threaded rods attached to the riser plate. Each rod contains four (4) 1/2” nuts, four
(4) 1/2” washers and four (4) nylon retaining washer.

Remove the outer and inner access panels from the ceiling column.

NOTE: The gas hose(s) and electrical conduit(s) have been wrapped and attached to the top of the ceiling
column to maximize the smooth movement of the lower telescopic portion of the ceiling column.

Remember the location of the attached electrical conduit(s) at the top of the ceiling column. Do not cut free the
bundle(s) of gas hose(s) and/or electrical conduit(s) inside the ceiling column. Cut the cable tie(s) holding the gas
hose(s) at the top of the ceiling column and pull the gas hose(s) into the ceiling column. Do not cut the cable tie(s)
holding the electrical conduit(s) in place at the top of the ceiling column unless there is absolutely no room for the
installer to attach the conduit(s) to the appropriate junction box(es) on the riser plate. Cut and remove the excess
length of conduit(s) that is not required to attach to the appropriate junction box(es).

NOTE: The smooth movement of the retractable ceiling column will be a ected, if the above notes are not
followed.

Remove the (4) nuts and  at washers from the bottom of the riser plate and hoist the ceiling column onto the riser
plate. Ensure the open access panel of the ceiling column is aligned with the access panel label on the riser plate.
Secure the ceiling column into place with the (4) washers and nuts. Ensure the ceiling column is level. Attach the
conduit(s) to the appropriate junction box(es) with the ceiling column fully extended. Ensure the electrical conduit(s)
are coiling around the handle shaft with very little slack as it heads up towards the top of the ceiling column. Attach
the gas hoses to the appropriate outlets in the riser plate. Slowly retract the lower telescoping portion of the ceiling
column and ensure that the electrical conduit(s) and gas hoses do not interfere with the smooth movement of the
ceiling column as it retracts. Extend and retract the lower telescoping portion of the ceiling column a few times and
ensure that the electrical conduit(s) and gas hoses do not get pinched by the springs, the lower telescoping portion
itself or the riser plate mounting bolts.

Remove the plastic  lm from the access plates.

Attach the inner access plates onto the lower telescoping portion of the ceiling column and test the movement of
the ceiling column to ensure that the movement is smooth. Attach the outer access plate onto the ceiling column.

Remove the plastic  lm from the mounted ceiling column.

Attach the (4) ceiling trim plates at the top of the ceiling column.

Approval Signature Date Phone No.

www.amico.com 11

Mounting Information

NOTE: Riser plate to be installed in ceiling with appropriate mounting structure and anti-sway sup­port. The methods of support shown are provided for information only.

17” Sq.

[431.8mm Sq.]

14.75” Sq.

[374.65mm Sq.]

STRUCTURAL CEILING

ANTI-SWAY SUPPORT STRUCTURE
(SUPPLIED BY OTHERS)

1.00” [25.4mm]

4.5”

[114.3mm]

FINISHED CEILING

COLUMN

MOUNTING

PLATE

9.5” Sq.

[241.3mm Sq.]

RISER
PLATE

17” Sq.

[431.8mm Sq.]

CEILING COVER

(FIELD MOUNTED)

3/4” [19.5mm] or 7/8” [22.23mm]
THREADED ROD (X4) (SUPPLIED BY OTHERS)

MIN. 13” [330.2mm] MAX.
16” SQ CEIILNG CUT-OUT
FOR COLUMN

1/2” [12.7mm] DIA. MOUNTING BOLTS FUR­NISHED WITH RUOGH-IN PLATE. TYP. OF 4, See
note 1.

NOTE:

1. All labour and material for installation of Riser to Mounting Structure supplied by others.

2. General Contractor has  nal responsibility for the strength and stability of the mounting structure that is

supplied by others.

3. Riser plate to be mounted 4.5” (114.3mm) above  nished ceiling.

4. Mounting of column unit to riser plate by (4) 1/2” threaded rods, provided by Amico.

5. Space between top of Riser Plate and structural ceiling must be minimum 10”(254mm).

6. Riser Pipe(s) extend 8” (203.2mm) above riser plate.

7. Pre-ship of the riser assembly is available upon customer’s request.

Approval Signature Date Phone No.

12 Amico Pipeline

Typical Location View

Wiring Diagram

Recommended location of
columns in surgeries and
special care areas.

3’ - 4’

[914.4 - 1219.2mm]

3' to 4'

[914.4 - 1219.2mm]

Access Panel

3' to 4'

Access Panel

3’ - 4’

[914.4 - 1219.2mm]

OPERATING

TABLE

3’ - 4’

3' to 4’

[914.4 - 1219.2mm]

OPERATING ROOM

3' to 4'

3’ - 4’

*Conduit and wiring to internal junction box by others.
Flexible conduit must be used. Allow a minimum of 24” (609.6mm) of wiring to internal junction box for extension and retraction of column.

Approval Signature Date Phone No.

www.amico.com 13

Remote (Optional)

Terminal Connections

RJ45

Model Number

Remote = C-EL-SWITCH-W

Approval Signature Date Phone No.

14 Amico Pipeline

Control Unit Speci cations

The control unit shall be designed to operate a maximum of 4 linear drives or telescopic columns in 24 V direct cur­rent technology.

It shall have an integrated transformer and recti er with plug connection for the main cable and hand-held or foot
switch. It will also have up to 3 motor connections or 2 motors and 2 limits with switch connections.

The switch shall be an optimal hand-held or foot switch or an infrared receiver that can be plugged in directly at the
control element connection. All control, and motor supply cables are locked after correct connection and sealed by
sealing rings.

When in no-load operation, the Amico control unit shall be the auxiliary transformer which is active and maintain
only the control voltage for the operating element (standby circuit). The transformer shall have thermal protection
to avoid overheating.

The control box shall be ultrasonically welded.

Amico products comply with NFPA-99 and CSA Z7396.1.

• low voltage control unit

• protected against overheating

• maintenance free

• minimum electromagnetic interference  elds radiated.

• total current cut-o prevents exceeding of current consumption and protects drives.

Motor Connection 3

Voltage/Frequency 120 / 60 V / HZ

Output Power 24 V DC / 6 A

Duty Cycle: Intermittent Mode 1 min. / 9 min. int.

Ambient Temperature 0 / +40C

Degree of Protection 66 IP

Weight 2.8 kg

Approval Signature Date Phone No.

www.amico.com 15

Control Unit Dimensions

7.05”

[179mm]

KOM 3/4 CONTROL UNIT KOM 3/4 CONNECTIONS

6.50”

[165mm]

6.57”

[167mm]

[228.6mm]

[153mm]

[139mm]

9”

6.02”

5.5”

3.15”

[80mm]

4.21”

[107mm]

5.5”

0

[139mm]

13.3”

9”

[337.82mm]

2.68”

[228.6mm]

[68mm]

9”

[228.6mm]

2.95”
[75mm]

Mains connections

Operating element

connection

Motor connections

External limit switch

(optional)

Model Number

Control Unit (power cord included) = C-EL-CNTROL-120V

16 Amico Pipeline

Approval Signature Date Phone No.

Linear Drive Speci cations

The linear actuators shall be designed for seating and reclining operations. It adjusts the column to the required
level by raising and lowering it.

The drive is provided by a DC motor with worm geat which acts on a trapexoidal threaded spindle drive or ball screw
system.

The actuators shall be protected against overheating by the Magnetic control unit.

Amico actuators shall use a push / pull force. They shall have a self-locking function which is activated by a built-in­brake. A safety nut shall also prevent overload of the actuator.

All forces shall be transmitted through die-cast metal parts.

Amico products comply with NFPA-99 and CSA Z7396.1.

• high-quality die-cast metal parts, stainless steel push tubes & ultrasonic-welded plastic parts guarantee high
performance

• customizable stroke & mounting lengths in increments of 1.97 - 15.75” [50 - 400mm] & increments of 3.94”
[100mm] over the range of 15.75 - 27.56” [400 - 700mm]; other options are available upon request.

• maintenance free with a long lifetime

• push force us reduced by 50% when operated in parallel with the control unit.

• quiet in running

Push / pull force 1.5N

Speed at 24 V constant 14 mm/s

Stroke 1.97 - 27.56” [50-700 mm]

Voltage 24 DC

Power Consumption 120 W

Current Consumption 24V 5 A

Duty Cycle (ON / OFF) 1 min / 9min. int.

Ambient Temperature 0 / +40 C

Degree of Protection IP66

Protective Tube 1.69” [43 mm]

Weight 3 kg

Approval Signature Date Phone No.

www.amico.com 17

Linear Drive Dimensions

4.21”

[107mm]

1.89”

[48mm]

1.57”
[40mm]

6.65”
[169mm]

2.6”

[66mm]

&RONTVIEW

3IDEVIEW

0.39”

0.98”
[10mm]

[25mm]

1.02”
[26mm]

O 0.47” +0.01” [0.15mm]

[12mm] +0.002” [0.05mm]

O 0.39” +0.01” [0.3mm]

0.34”

[8.7mm]

[10mm] +0.01” [0.2mm]

" EARING INSERT FORFORKHEAD 4OPVIEW

1.67”

1.10”

[42.5mm]

[28mm]

1.10”

0.59”

[15mm]

0.43”

[28mm]

O 0.25” [6.3mm]

[11mm]

+0.01” [ 0.3mm]
O 0.47” [12mm] +0.004” [0.1mm]

RL = min. 7.68” [195mm] + stroke 0.08” [2mm]

0.47”

[12mm]

1.10”
[28mm]

+0.01” [ 0.3mm]
O 0.47” [12mm] +0.004” [0.1mm]

2.6”

[66mm]

+

_

4.57”

[116mm]

0.55”

[14mm]

0.59”

[15mm]

0.43”
[11mm]

1.10”
[28mm]

Model Number

Linear Drive = 30" [762mm] Column: C-X-ELEC-CYL-10

36" [914.4mm] Column: C-X-ELEC-CYL-14

42" [1066.8mm] Column: C-X-ELEC-CYL-18

Approval Signature Date Phone No.

18 Amico Pipeline

Servicing

WARNING

Always shut o source pressure at designated zone valves before servicing any gas outlet.

The periodic inspection of gas outlets and electrical outlet is recommended to ensure proper safety and operation.

A) Gas Outlet

* Inspect the gas outlet connection points for the following:

1. Proper and legible identi cation.

2. Worn or defective engagement mechanisms.

3. Leaks.

4. Deformed or damaged threaded connections.

5. Loose fasteners.

WARNING

Use care when wiping down electrical outlets to prevent electrical shock.

B) Electrical

* Inspect the electrical outlet connection points for the following:

1. Proper and legible identi cation.

2. Deformation or damage

3. Discoloration

Approval Signature Date Phone No.

www.amico.com 19

www.amico.com

Amico Architectural | www.amico.com

85 Fulton Way, Richmond Hill

Ontario, L

4B 2N4, Canada

71 East Industry Court, Deer Park
NY 11729, U.S.A

Toll Free Tel: [phone]
Toll Free Fax: [phone]
Tel: [phone]

Fax: [phone]
Email: [e-mail]

C US LISTED

ac_instal_maint_mot_retr_ceil_col PRINTED FEB 12