AmFor 881 User Manual

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead A

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt on to the alternator pulley. Make sure the belt is under the motor pulley belt retaining clip. Slide the green handle to the right, locking the handle into the retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE (hold for no more than 3 seconds). Observe meters for proper readings.

Red clip

pdc/nwr/inv/881/881-manual/green/889-A.cdr

Black clip

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0, unless W connected

then 7 to 8

STARTER VOLTAGE

STATOR VOLTAGE

0, unless W connected

then 7 to 8

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead B

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

W terminal, connected only when W spade is present on alternator

pdc/nwr/inv/881/881-manual/green/889-B.cdr

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead BD

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

pdc/nwr/inv/881/881-manual/green/889-BD.cdr

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

13-16

STARTER VOLTAGE

STATOR VOLTAGE

13-16

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead BM

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

If battery post is not available, connect here

pdc/nwr/inv/881/881-manual/green/889-BM.cdr

EXTERNALLY REGULATED

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0, unless W connected

then 7 to 8

STARTER VOLTAGE

STATOR VOLTAGE

0, unless W connected

then 7 to 8

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead BT

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-BT.cdr

W terminal, connected only when W spade is present on alternator

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead C

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

pdc/nwr/inv/881/881-manual/green/889-C.cdr

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead CD

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

pdc/nwr/inv/881/881-manual/green/889-CD.cdr

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

7-8

STARTER VOLTAGE

STATOR VOLTAGE

7-8

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

Red clip

Black clip

pdc/nwr/inv/881/881-manual/green/889-D.cdr

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Test Lead D

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

EXTERNALLY REGULATED

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead El1

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

Green

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

pdc/nwr/inv/881/881-manual/green/889-EL1.cdr

EXTERNALLY REGULATED

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead EL2

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4. Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

6. Reverse the BLACK and GREEN test lead wires and retest.

Red clip

Black clip

Green

Black

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

pdc/nwr/inv/881/881-manual/green/889-EL2.cdr

FLD FLDFLD FLD

EXTERNALLY REGULATED

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead EL3

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%..

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

Green

White

Black

pdc/nwr/inv/881/881-manual/green/889-EL3.cdr

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

EXTERNALLY REGULATED

STA

FLD

GRD

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8 (sta)

14-16 (61, d+)

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8 (sta)

14-16 (61, d+)

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead EL4

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

Green

White

Black

pdc/nwr/inv/881/881-manual/green/889-EL4.cdr

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

EXTERNALLY REGULATED

D-D-

FLD

or DF

FLD

or DF

B+

D-

F+

61

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead F

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

pdc/nwr/inv/881/881-manual/green/889-F.cdr

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

EXTERNALLY REGULATED

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead FA

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin. Make sure “A” circuit adapter is connected.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

pdc/nwr/inv/881/881-manual/green/889-FA.cdr

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

“A” Circuit

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-FB.cdr

Test Lead FB “A" CircuitTest Lead FB “A" Circuit

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead FC

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

pdc/nwr/inv/881/881-manual/green/889-FC.cdr

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

EXTERNALLY REGULATED

Green

White

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead FT

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

pdc/nwr/inv/881/881-manual/green/889-FT.cdr

EXTERNALLY REGULATED

Green

Red

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead FV

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-FV.cdr

W terminal, connected only when W spade is present on alternator

W TerminalW Terminal

Slide on connector used when post is not present

D+

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead G

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than10 seconds.

Red clip

Black clip

pdc/nwr/inv/881/881-manual/green/889-G.cdr

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

EXTERNALLY REGULATED

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0, unless P

connected, then 7 to 8

STARTER VOLTAGE

STATOR VOLTAGE

0, unless P

connected, then 7 to 8

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

Red clip

Black clip

pdc/nwr/inv/881/881-manual/green/889-H.cdr

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Test Lead H

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

“P” terminal, connected only when P spade is present on alternator

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

Red clip

Black clip

pdc/nwr/inv/881/881-manual/green/889-HL.cdr

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Test Lead HL

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead ID

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-ID.cdr

S L

IGIG

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead IG

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-IG.cdr

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead IN

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-IN.cdr

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead J

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%..

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

Pdc/nwr/inv/881/881-manual/green/889-J.cdr

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

EXTERNALLY REGULATED

onon

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead JD

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-JD.cdr

L

S

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead K

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%..

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

Pdc/nwr/inv/881/881-manual/green/889-K.cdr

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

EXTERNALLY REGULATED

offoff

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

Red clip

Black clip

Pdc/nwr/inv/881/881-manual/green/889-LR.cdr

Test Lead LR

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

00

3030

1010

2020

STARTER / STATOR

VO LTAG E

STARTER / STATOR

VO LTAG E

STARTER VOLTAGE

STATOR VOLTAGE

13 to 16

STARTER VOLTAGE

STATOR VOLTAGE

13 to 16

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead M

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%..

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

Pdc/nwr/inv/881/881-manual/green/889-M.cdr

EXTERNALLY REGULATED

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

STARTER VOLTAGE

STATOR VOLTAGE

13 to 16

STARTER VOLTAGE

STATOR VOLTAGE

13 to 16

offoff

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

Red clip

Black clip

Pdc/nwr/inv/881/881-manual/green/889-MD.cdr

Test Lead MD

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

STARTER VOLTAGE

STATOR VOLTAGE

13 TO 16 if "R" terminal

is present

0 if no "R" terminal

STARTER VOLTAGE

STATOR VOLTAGE

13 TO 16 if "R" terminal

is present

0 if no "R" terminal

L RL R

SS

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

Pdc/nwr/inv/881/881-manual/green/889-N-A.cdr

Test Lead N “A" CircuitTest Lead N “A" Circuit

onon

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Red clip

Black clip

Pdc/nwr/inv/881/881-manual/green/889-N-B.cdr

Test Lead N “B” CircuitTest Lead N “B” Circuit

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

offoff

EXTERNALLY REGULATED

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%..

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead P

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin. Make sure “A” circuit adapter is connected.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

Pdc/nwr/inv/881/881-manual/green/889-P.cdr

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

“A” Circuit

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER VOLTAGE

STATOR VOLTAGE

7 to 8

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead S

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Pdc/nwr/inv/881/881-manual/green/889-S.cdr

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

0

200

100

50

150

STARTER

AMPS

0

2

4

6

8

10

MILLIAMPERE

METER

0

30

10

20

ALTERNATOR

VOLTAGE

0

30

10

20

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

2 to 12

STARTER AMPERAGE

0

4 a m p

Blue

Green

Red

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

off

Test Lead SC

Test Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4. Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Readings for a good alternator are in the shaded area. All meter

Red clip

Black clip

0

30

10

20

STARTER / STATOR

VOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-SJ.cdr

EXTERNALLY REGULATED

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead SI

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Pdc/nwr/inv/881/881-manual/green/889-SI.cdr

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

STARTER VOLTAGE

STATOR VOLTAGE

6 to 8

(some Cadillac alternators

may read less)

STARTER VOLTAGE

STATOR VOLTAGE

6 to 8

(some Cadillac alternators

may read less)

1 21 2

RR

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead SJ

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4. Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-SJ.cdr

EXTERNALLY REGULATED

F1 F2

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead SK

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4. Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-SK.cdr

EXTERNALLY REGULATED

F1 F2

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0, unless P

connected, then 7 to 8

STARTER VOLTAGE

STATOR VOLTAGE

0, unless P

connected, then 7 to 8

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

Red clip

Black clip

Pdc/nwr/inv/881/881-manual/green/889SL.cdr

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Test Lead SL

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

“P” terminal, connected only when P spade is present on alternator

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead SN

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4. Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-SN.cd

EXTERNALLY REGULATED

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead T

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Pdc/nwr/inv/881/881-manual/green/889-T.cdr

Black clip

00

3030

1010

2020

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead TD

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-TD.cdr

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead U

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Pdc/nwr/inv/881/881-manual/green/889-U.cdr

Black clip

00

3030

1010

2020

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead V

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin. Make sure “A” circuit adapter is connected.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

Pdc/nwr/inv/881/881-manual/green/889-V.cdr

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

“A” Circuit

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

13-16

STARTER VOLTAGE

STATOR VOLTAGE

13-16

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead VO

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-VO.cdr

EXTERNALLY REGULATED

D+D+

B+B+

D+ DFD+ DF

D-D-

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

13-16

STARTER VOLTAGE

STATOR VOLTAGE

13-16

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead VW

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-VW.cdr

EXTERNALLY REGULATED

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead WF

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4. Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-WF.cd

EXTERNALLY REGULATED

00

200200

100100

5050

150150

STARTER

AMPS

STARTER

AMPS

00

22

44

66

88

1010

MILLIAMPERE

METER

MILLIAMPERE

METER

00

3030

1010

2020

ALTERNATOR

VOLTAGE

ALTERNATOR

VOLTAGE

00

3030

1010

2020

ALTERNATOR

AMPS

ALTERNATOR

AMPS

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER VOLTAGE

STATOR VOLTAGE

0

STARTER AMPERAGE

0

STARTER AMPERAGE

0

4 a m p

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER

6 or less

MILLIAMPERE METER

6 or less

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR VOLTAGE

13 to 16

ALTERNATOR AMPERAGE

12 to 16

ALTERNATOR AMPERAGE

12 to 16

offoff

Test Lead Y

Test LeadsTest Leads

and

881 Alternator Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4. Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

00

3030

1010

2020

STARTER / STATOR

VOLTAGE

STARTER / STATOR

VOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-Y.cd

EXTERNALLY REGULATED

AmFor 881 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual