American Standard T385.507, T385.508 User Manual
Installation
Instructions
Reliant 3
BAT H A N D S H O W E R T R I M K I T S
T385.508
T385.507
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
RECOMMENDED TOOLS
Phillips Screwdriver
ROUGHING-IN DIMENSIONS
To assure proper positioning in relation to wall, note
roughing-in dimensions.
FINISHED WALL
4-1/4" REF.
6" REF.
Flat Blade Screwdriver
3/4"" TO 2-3/8"
1/2" NPT
OPTIONAL TO FINISHED
BETWEEN 65'' AND 80''
Plumbers' Putty or Caulking
FLOOR USUALLY
SHR. 1/2" NOM.
COPPER SWEAT
TUB 1/2" NOM.
COPPER SWEAT
SWEAT
INLETS
Certified to comply with ANSI A112.18.1
Adjustable Wrench
INLETS
4-1/16"
INLETS
1/2" NOM.
COPPER
SWEAT
2"
4-1/16"
M 9 6 8 6 90
Teflon Tape
"SEE ILLUSTRATION "
74" FOR HEAD
CLEARANCE
18" OPTIONAL
5-1/2" REF.
TOP OF TUB RIM
BOTTOM OF TUB
SHR
7-5/8”
TUB
1-1/2" REF.
1/2" COPPER
4"
3-3/8"
3-3/8"
OUTLETS
1/2" NPT
SWEAT
INLETS (STOPS)
SHR. 1/2" NOM.
COPPER SWEAT
TUB 1/2" NOM.
COPPER SWEAT
INLETS 1/2" NPT
THREADED INLETS
3-3/8"
5-7/8"
4-1/16"
INLETS
1/2" NOM.
COPPER
SWEAT
OUTLETS
1/2" NPT
5-7/8"
INLETS
1/2" NPT
THREADED INLETS (STOPS)
INSTALL TRIM
1
When finished tiling the wall, remove PLASTER GUARD (3).
Push on CAP (1).
Mount ESCUTCHEON (2) and with SCREWS (7).
Install HANDLE (8) by pushing it onto CARTRIDGE STEM (9)
and tightening SET SCREW (10) from below with 2.5mm
Hex Wrench supplied. Insert INDEX BUTTON (11).
Remove cap from tub supply and plug from shower pipe.
Install SHOWER ARM (4) and FLANGE (13). Install
SHOWER HEAD (5). See Step 2.
12
13
4
5
9
1
3
2
7
Tighten SET SCREW (12) onto FLANGE (13)
using 5/64” hex wrench.
Install DIVERTER SPOUT (6).
INSTALL SHOWER HEAD ASSEMBLY
2
REMOVE SHOWER HEAD FROM HOUSING
Hold SHOWERHEAD (1) with one hand and HOUSING (2)
with the other as illustrated.
Rotate SHOWERHEAD (1) clockwise while holding HOUSING (2)
stationary. NOTE: The thread connection is a left hand
thread. Keep turning SHOWERHEAD (1) until it can be
removed from the HOUSING (2).
2a
INSTALL HOUSING
Slide HOUSING (2) onto
SHOWER ARM (3).
3
1-1/2" REF.
6
1
2b
INSTALL SHOWER HEAD
Rap SHOWER ARM (3) threads with Teflon tape.
Tighten SHOWERHEAD (1)
with an adjustable wrench.
Do not over tighten.
TEFLON TAPE
3
8
10
11
2
2
2c
INSTALL HOUSING TO SHOWER HEAD
Install HOUSING (2) onto SHOWER HEAD (1). Thread
HOUSING (2) counter-clockwise to install onto SHOWER
HEAD (1). Hand tighten only.
1
1
2
M 9 6 8 6 90 M 9 6 8 6 90 M 9 6 8 6 90
Loading...