American Standard M968120 User Manual
Installation
Instructions
2930.000
CENTERSET
LAVATORY FAUCET
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
INDEX
BUTTON
HANDLE
SCREW
LEVER
HANDLE
Certified to comply with ANSI A112.18.1M
M968120
LIFT
ROD
CARTRIDGE
MOUNTING
NUT
COUPLING
NUT
AERATOR
CLIP
PIVOT
ROD
BUSHING
THUMBSCREW
EXTENSION
0-RING
STOPPER
DRAIN
FLANGE
GASKET
WASHER
LOCKNUT
DRAIN
BODY
TAILPIECE
INSERT
TAILPIECE
INSTALL FAUCET
1
CAUTION
Turn off hot and cold water supplies before beginning.
BODY
LIFT
ROD
Apply a bead of PUTTY along the edge of the underside of the BODY. Insert
faucet SHANKS through holes of SINK.
Place faucet as far forward as possible.
Assemble and tighten MOUNTING NUTS from underside of SINK.
Connect the HOT water supply to the left SHANK and the COLD water supply to
the right SHANK using sealant, appropriate connectors, and COUPLING NUTS.
Insert LIFT ROD through hole in BODY.
INSTALL POP-UP DRAIN
2
STOPPER
Thread TAILPIECE into DRAIN BODY and tighten securely.
Thread LOCKNUT fully onto DRAIN BODY. Drop WASHER
and GASKET onto DRAIN BODY.
Remove CLIP from PIVOT ROD. Assembly PIVOT ROD
to DRAIN BODY with BUSHING.
Apply a bead of putty to underside of FLANGE.
SINK
Insert DRAIN BODY from below through SINK
hole with the PIVOT ROD pointed toward the LIFT ROD.
Thread FLANGE fully onto DRAIN BODY. Tighten
LOCKNUT firmly, keeping the PIVOT ROD pointed
toward the LIFT ROD.
LOCKNUT
Slide EXTENSION onto LIFT ROD and insert PIVOT ROD
through the second or third hole. Secure with CLIP.
EXTENSION may need to be bent to suit installation.
Move PIVOT ROD fully downward. Tighten THUMBSCREW.
SINK
FLANGE
PUTTY
GASKET
WASHER
0-RING
TAILPIECE
INSERT
TAILPIECE
TRAP
PUTTY
SHANK
MOUNTING
NUT
COLD
HOT
COUPLING NUT
Drop STOPPER into DRAIN BODY. Operate LIFT ROD.
Adjust STOPPER movement by repositioning EXTENSION
on LIFT ROD.
LIFT ROD
EXTENSION
ROD
PIVOT
ROD
CLIP
CLIP
PIVOT
ROD
BUSHING
THUMBSCREW
DRAIN
BODY
TAILPIECE
TRAP
EXTENSION
ROD
TEST INSTALLED FAUCET
3
Remove AERATOR.
Turn HANDLES to OFF position.
Slowly turn on water supplies and check all connections
for leaks.
SERVICE
4
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
For toll-free information and answers to your questions, call:
Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time
Saturdays 8:00 a.m. to 4:00 p.m. Eastern Time
IN CANADA 1-800-387-0369 (TORONTO 1-416-536-5609)
Product names listed herein are trademarks of American Standard Inc.
©American Standard Inc. 1999
HOT LINE FOR HELP
1 (800) 223-0068
Operate both HANDLES to flush water lines thoroughly.
Operate LIFT ROD and check DRAIN connections for leaks.
Turn HANDLES to OFF position and replace AERATOR.
ALIGN HANDLES
Turn HANDLES to their off position.
Remove INDEX BUTTON and HANDLE
SCREW.
Remove HANDLE and replace on
VALVE STEM in desired position.
Replace HANDLE SCREW and INDEX
BUTTON.
VALVE
STEM
INDEX
BUTTON
HANDLE
SCREW
LEVER
HANDLE
M968120
Loading...