American Standard M962689-0070A, M962688-YYY0A, M962659-0070A, 4332.300.XXX, M962690-0070A User Manual
Page 1
Installation
Instructions
PEKOE PULL DOWN
4332.300.XXX
SINGLE CONTROL KITCHEN
FAUCET with PULL DOWN SPRAY
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Recommended Tools
Phillips Screwdriver
INSTALL FITTING
1
CAUTION
Turn off hot and cold water
supplies before beginning.
Channel Locks
Adjustable Wrench
Plumbers' Putty or Caulking
Certified to comply with ANSI A112.18.1M
M968581 Rev.1.1
Tubing Cutter
Make certain the O-RING SEAL (1) is properly seated
in recess of faucet body.
Insert supply HOSES (2), SHANK (3) and SPRAY
HOSE (4) through center hole of sink or mounting
surface.
Assemble RUBBER WASHER (5), PLASTIC WASHER (6),
RUBBER & METAL “C” WASHERS (7) and long LOCKNUT (8)
onto SHANK (3) from underside of sink. Hand tighten
LOCKNUT (8) and check that faucet is centered.
Tighten LOCKNUT (8) with WRENCH (12) supplied. Insert
screwdriver into hole in WRENCH (12) and tighten.
Feed HOSE END (9) through HOSE GUIDE (10). Slide other
side of HOSE GUIDE (10) onto SHANK (3) and secure with
LOCK NUT (11). Do not over tighten!
RECESS
5
6
7
10
1
4
3
8
11
9
2
12
SCREWDRIVER
Page 2
MAKE WATER SUPPLY CONNECTIONS
2
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection
on fitting supplies are 3/8" compression. Connect left supply
(Marked with a Red Stripe) to Hot and right supply (Marked with
Blue Stripe) to Cold wall supply. Use adjustable wrench to
tighten connections. Do not over tighten.
RED
STRIPE
BLUE
STRIPE
Faucet supplies are 27-1/2" long from faucet base.
Note: If additional supply length
is required, installer must
purchase additional parts
separately.
Important: If SUPPLY HOSES
(1, 2) are too long, loop as
illustrated to avoid kinking.
CONNECT HOSE SPRAY
3
and INSTALL WEIGHT
Check that seal washers are installed in both ends of SPRAY HOSE ADAPTER (1).
Thread SPRAY HOSE ADAPTER (1) onto faucet SHANK (2). Tighten with adjustable wrench.
Thread HOSE END (3) into bottom of SPRAY HOSE ADAPTER (1). Tighten with adjustable wrench.
Make sure all connections are tight. Figure 1.
Install RUBBER BUSHING (4) onto SPRAY HOSE (5). Install WEIGHTS (6) onto HOSE (5) using two screws (7). Locate
WEIGHTS (6) 18" from underside of mounting surface on HOSE (5). Tighten SCREWS (5) firmly. Figure 2.
1
HOT
2
COLD
Figure 1.
Figure 1
UNDER SIDE
OF MOUNTING
SURFACE
2
SEAL
WASHER
1
18"
SEAL
3
WASHER
6
4
57
Figure 2
M968581 Rev.1.1
Page 3
TEST INSTALLED FAUCET
4
Move HANDLE (1) into "off" position.
Unthread SPRAY HOSE (3) from SPRAY (2).
Turn on water supplies and check connections for leaks
Hold HOSE END (3) in sink and operate HANDLE (1) on and off,
hot and cold to flush water lines thoroughly. Replace SPRAY (2).
Pull SPRAY (2) out and check hose and supply connections
for leaks. Check that SPRAY HOSE (3) and WEIGHT (4) slide
up and down freely and do not interfear with supplies or waste
outlet plumbing. With faucet on push BUTTON (5) to spray
and aerator fuctions.
Check all drain connections for leaks.
Move HANDLE (1) to "off" position.
SERVICE
5
3
.
2
5
1
4
3
HOT & COLD SUPPLIES
Clogged CARTRIDGE outlets or inlets may cause reduced
flow. To clean, first turn off water supply then:
Loosen and remove LEVER HANDLE (1). Loosen HANDLE
SCREW (2) with 2.5mm Hex Wrench and then pull HANDLE
BASE (3) off.
Unthread ESCUTCHEON CAP (4). Unthread the
CARTRIDGE NUT (5).
Remove CARTRIDGE (6). Clean inlets of CARTRIDGE (6)
and MANIFOLD (7).
Reassemble CARTRIDGE (6). Replace CARTRIDGE
NUT (5), CAP (4) and HANDLE assembly, check flow.
If SPOUT (11) leaks at swivel point the O-RINGS (12) need
to be replaced. To remove SPOUT (11):
Disconnect SPRAY HOSE (8) from CONNECTING NUT (9).
Loosen the SPOUT SET SCREW (10) with a 3mm Hex wrench.
Rotate the SPOUT (11) side to side while pulling upward to
remove SPOUT (11) from faucet body. Remove SPRAY HOSE (8).
Replace the defective parts and grease O-RINGS (12). Replace SPRAY
HOSE (8). Push SPOUT (11) back into position. Tighten SET SCREW (10).
Reconnect SPRAY HOSE (8) to CONNECTING NUT (9).
Check that SPOUT (11) rotates freely and does not leak
at the swivel point.
11
REMOVE
INSTALL
12
10
CLEAN
7
9
8
3mm
HEX WRENCH
6
1
5
4
2
3
CARE INSTRUCTIONS:
6
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
M968581 Rev.1.1
Page 4
M962643-YYY0A
SPRAY HOSE
AND SEALS
M962683-YYY0A
PULL-OUT SPRAY
WITH CHECK VALVE
M962684-YYY0A
AERATOR SET
M962648-0070A
SPOUT BUSHING
& O-RING KIT
M962687-YYY0A
SPOUT ASSEMBLY
M962652-0070A
SPOUT SET SCREW
PEKOE PULL DOWN
SINGLE CONTROL KITCHEN
FAUCET WITH PULL
DOWN SPRAY
MODEL NUMBER
4332.300.XXX
M962690-0070A
CARTRIDGE NUT
M9629691-YYY0A
CARTRIDGE COVER
M962685-YYY0A
PEDESTAL
M962686-0070A
O-RING
Replace the "YYY" with
appropriate finish code
CHROME 002
STAINLESS STEEL 075
M962688-YYY0A
HANDLE KIT
M962689-0070A
CARTRIDGE
M962659-0070A
MOUNTING KIT
M962660-0070A
HOSE GUIDE
M962661-0070A
NUT
M968581 Rev.1.1
M962650-0070A
HOSE WEIGHTS
M962662-0070A
SPRAY HOSE ADAPTER
WITH CHECK VALVE
For toll-free information and answers to your questions, call:
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2008
HOT LINE FOR HELP
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-12-00
Loading...