Page 1
Installation
Instructions
COMMERCIAL WALL
MOUNTED SHOWERHEAD
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
1660.243
1660.244
Certified to comply with ANSI A112.18.1
M 9 6 5 2 4 0 R E V. 1. 1
Recommended Tools & Materials
Phillips Screwdriver
Hammer
Pencil
Teflon tape
3/32" Hex Wrench
3mm (1/8")
Drill Bit
Electric Drill
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.
ROUGHING-IN DIMENSIONS
57mm
1/2-14 NPT
37mm
(1-7/16")
17mm
(11/16")
13mm
(1/2")
(2-1/4")
30
˚
7.2 mm
(5/16") DIA.
HOLES
54mm
(2-1/8")
65mm
(2-9/16")
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 65'' AND 80''
(1651 and 2032mm)'
37mm
(1-7/16")
FINISHED FLOOR
FINISHED FLOOR
37mm
(1-7/16")
74mm
(2-7/8")
90mm
(3-1/2")
Page 2
INSTALL SHOWER HEAD
1
Thread SHOWER HEAD (1) hand tight onto SUPPLY NIPPLE (2). FIG. 1.
Level SHOWER HEAD (1). Mark the location of the three mounting holes. Remove SHOWER HEAD (1). FIG. 2.
Drill three 1/8" diameter holes a minimum of 1-1/4" deep. With a hammer tap the three ANCHORS (3) (not supplied)
flush with face of the finished wall. FIG. 3.
Apply TEFLON TAPE (4) to SUPPLY NIPPLE (2). FIG. 4.
Thread SHOWER HEAD (1) onto SUPPLY NIPPLE (2). Use a strap wrench to protect finish. Fully tighten and check for level.
Turn shower on and check for leaks. Tighten if required. FIG. 5.
Install the MOUNTING SCREWS (5) (not supplied) and fully tighten to secure the SHOWER HEAD (1) to the wall. FIG. 5.
CAUTION
Turn off hot and cold water
supplies before beginning.
FIG. 1.
2
1
FIG. 2.
FIG. 4.
2
APPLY SEALANT
OR TEFLON TAPE
4
DRILL THREE 1/8"
DIAMETER HOLES
FIG. 3.
2
1
BOTTOM EDGE
SHOULD BE LEVEL
3
5
FIG. 5.
M 9 6 5 2 4 0 R E V. 1. 1
Page 3
M964243-0070A
FLOW REGULATOR
2.0 gpm, (7.6L/min.)
M923208-0070A
FLOW REGULATOR
1.5 gpm, (5.7L/min.)
COMMERCIAL WALL
MOUNTED SHOWERHEAD
MODEL NUMBER
1660.243
1660.244
Appropriate finish code
CHROME 002
For toll-free information and answers to your questions, call:
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2012
HOT LINE FOR HELP
1-800 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN MEXICO 01-800-839-1200
Weekdays 8:00 a.m. to 7:00 p.m. EST
M 9 6 5 2 4 0 R E V. 1. 1
Loading...