American Standard APS-997 User Manual

Installation Manual

Model APS-997

SELECT ABLE FEA TURES

Note : The method of manual override can either be selected to operate from the valet switch or operate as custom code.

Be certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.

NOTE: Keyless Entry Models with no horn output will Flash the Parking Lights instead of chirp where chirp is indicated.

Also, No data will be indicated if a feature is not available for a particular model. The unit will enter the feature but no selection will be available.

RF Programmable Feature Bank 1 Is For Transmitter Programming See Transmitter Programming Guide.

RF Programmable Features Bank 2 Is Alarm Selectable Features:

Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps 5 Chirps 6 Chirps

1st DoorL/UL 1 Sec. 3.5 Sec. 1 Sec L, Dbl. U/L Dbl L, 1 Sec UL Dbl L, Dbl UL 1 S l/350mS ul

2nd Accy Lock Auto Lock On Auto Lock Off

3rd Accy. UL Auto UL Dr. Auto UL All Auto UL Off

4th Headlights On Arm On Disarm On Both Off

5th Passive Locks Passive Active

6th Pass/Act Arm Passive Arm Active Arm

7th Siren/Horn Siren/Horn Siren Only Horn Only

8th Horn Chirp 10mS 16mS 30mS 40mS 50mS

9th O/R Method Custom Code Valet

10th 2 Step U/L On Off

11th Chp Del Tx On Off

12th Volts/HdWire Not Available

13th Trigger Circuits Not Available

14th L/UL Poll Not Available

When using the RF programmer, enter the program mode as follows:

Turn the ignition on

Press and release valet switch 3 times

turn ignition off then on

The selectable features can be set manually as explained below, or with the RF feature programmer .

T o set features using the RF programmer , follow the instructions packaged with the programmer.

Factory default settings are indicated by bold text.

Press and hold valet switch for 5 seconds

128-7402

1 of 28

Siren chirps 2 times indicating access to RF feature program mode.

To program these selectable features;

Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Then On Short chirp, then long chirp This Action Accesses Feature Bank 2 Alarm Selectable Features

First Press and release the valet switch 1 time 1 chirp = 1 second door lock & unlock

Second Press and release the valet switch 2 chirps = auto locks off

Third Press and release the valet switch 3 chirps = auto unlock off

Fourth Press and release the valet switch 3 chirps = headlight output when arming and disarming

Fifth Press and release the valet switch 2 chirps = active locks

Sixth Press and release the valet switch 2 chirps = active arming

Seventh Press and release the valet switch 1 chirp = siren and horn output

Eighth Press and release the valet switch 2 chirps = horn chirp output 16mS

Ninth Press and release the valet switch 2 chirps = valet switch override operation

Tenth Press and release the valet switch 2 chirps = 2 step unlock off

Eleventh Press and release the valet switch 2 chirps = chirp delete from transmitter inactive

Twelfth Press and release the valet switch Non Functional On This Unit Thirteenth Press and release the valet switch Non Functional On This Unit Fourteenth Press and release the valet switch Non Functional On This Unit Press and release the valet switch or turn the ignition off to: Exit Programming Mode

Turn ignition switch off then on to advance to feature Bank 3:

Press transmitter Lock button to change 2 chirps = 3.5 second door lock & Unlock Press transmitter Lock button to change 3 chirps = 1 sec. lock, dbl 1 sec. unlock Press transmitter Lock button to change 4 chirps = dbl 1 sec lock, 1 sec unlock Press transmitter Lock button to change 5 chirps = dbl 1 sec lock, dbl 1 sec unlock Press transmitter Lock button to change 6 chirps = 350mS unlock. 1 sec lock

Press transmitter Lock button to change 1 chirp = auto locks on

Press transmitter Lock button to change 1 chirp = auto unlock drivers door only Press transmitter Lock button to change 2 chirps = auto unlock all doors

Press transmitter Lock button to change 4 chirps = headlight output off Press transmitter Lock button to change 1 chirp = headlight output when arming Press transmitter Lock button to change 2 chirps = headlight output when disarming

Press transmitter Lock button to change 1 chirp = passive locks

Press transmitter Lock button to change 1 chirp = passive arming

Press transmitter Lock button to change 2 chirps = siren output only Press transmitter Lock button to change 3 chirps = horn output only

Press transmitter Lock button to change 3 chirps = horn chirp output 30mS Press transmitter Lock button to change 4 chirps = horn chirp output 40mS Press transmitter Lock button to change 5 chirps = horn chirp output 50mS Press transmitter Lock button to change 1 chirp = horn chirp output 10 mS

Press transmitter Lock button to change 1 chirp = custom code override operation

Press transmitter Lock button to change 1 chirp = 2 step unlock on

Press transmitter Lock button to change 1 chirp = chirp delete from transmitter active

or or or or or

128-7402

2 of 28

4 times with the key to be effective.

To exit program mode, turn ignition off, or press and release valet switch.

RF Programmable Features Bank 3 Is Remote Start Selectable Features:

Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps 5 Chirps 6 Chirps

1st Defrost Output Pulsed 10 Mins

2nd RF Start Chirp Off On

3rd Run Time 5 Mins 10 Mins 15 Mins 20 Mins

4th Parking Lights On Steady Flashing

5th Input Check Voltage Tach

6th Voltage Level >0.5V B4 Start < 0.5V B4 Start

7th Ing. 2 Select Off During Crank On During Crank Same As Accy.

8th Ign. 3 Select Off During Crank On During Crank Same As Accy

9th Diagnostics Off On

10th Crank Time 0.8 Sec 1.0 Sec 1.5 Sec 2.0 Sec

11th Gas/Diesel Gas Diesel 10 Diesel 15 Diesel 20

12th Transponder O/P While R/S On During Start Until Ign. Off

13th T emp Start Off On

14th Crank Averaging Averaging Preset Time Note: When averaging, the engine must be started

15th R/S Shock Shunt Unitl Clear Shunt R/S Cycle Shunt From Tx

16th Turbo Select Off 3 Mins 5 Mins 10 Mins

17th Black/Blue (Aux O/P) Single Pulse As Feature #1

When using the RF programmer, enter the program mode as follows:

Turn the ignition on

Press and release valet switch 3 times

turn ignition off then on

Press and hold valet switch for 5 seconds

Siren chirps 2 times indicating access to RF feature program mode.

To exit program mode, turn ignition off, or press and release valet switch.

128-7402

3 of 28

Action System Response

First Press the valet switch one time 1 chirp = defrost output pulsed

Second Press and release the valet switch 2 chirps = RF start chirp on

Third Press and release the valet switch 2 chirps = run time set for 10 mins

Fourth Press and release the valet switch 1 chirp = parking lights on steady w/RS active

Fifth Press and release the valet switch 2 chirps = tachometer input checking

Sixth Press and release the valet switch 1 chirp = greater than 0.5 V check before start

Seventh Press and release the valet switch 2 chirps = ign 2 on during crank

Eighth Press and release the valet switch 2 chirps = ign 3 on during crank

Ninth Press and release the valet switch 1 chirp = diagnostics off

Tenth Press and release the valet switch 2 chirps = crank time 1.0 sec

Eleventh Press and release the valet switch 1 chirp = unit set for gasoline engine

Twelfth Press and release the valet switch 1 chirp = transponder output while R/S active

Thirteenth Press and release the valet switch 1 chirp = temperature start off

Fourteenth Press and release the valet switch 1 chirp = crank averaging w/voltage input checking

Fifteenth Press and release the valet switch 1 chirp = shk sensor shunted until clear

Sixteenth Press and release the valet switch 1 chirp = turbo timer off

Seventeenth Press and release the valet switch 1 chirp = aux o/p Black/Blue single pulse Press and release the valet switch or turn the ignition off to: Exit Programming Mode

Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off, On, Off, On Short chirp, then 2 long chirps This Action Accesses Feature Bank 3 Remote Start Selectable Features

Press transmitter Lock button to change 2 chirps = defrost output 10 Mins

Press transmitter Lock button to change 1 chirp = RF start chirp off

Press transmitter Lock button to change 3 chirps = run time set fro 15 mins Press transmitter Lock button to change 4 chirps = run time set for 20 mins Press transmitter Lock button to change 1 chirp = run time set for 5 mins

Press transmitter Lock button to change 2 chirps = parking lights flashing w/RS active

Press transmitter Lock button to change 1 chirp = voltage sense input checking

Press transmitter Lock button to change 2 chirps = less than 0.5 V check before start

Press transmitter Lock button to change 3 chirps = ign 2 same as accessory Press transmitter Lock button to change 1 chirp = ign 2 off during crank

Press transmitter Lock button to change 3 chirps = ign 3 same as accessory Press transmitter Lock button to change 1 chirp = ign 3 off during crank

Press transmitter Lock button to change 2 chirps = diagnostics on

Press transmitter Lock button to change 3 chirps = crank time 1.5 sec Press transmitter Lock button to change 4 chirps = crank time 2.0 sec Press transmitter Lock button to change 1 chirp = crank time 0.8 sec

Press transmitter Lock button to change 2 chirps = unit set for diesel engine 10 sec delay Press transmitter Lock button to change 3 chirps = unit set for diesel engine 15 sec delay Press transmitter Lock button to change 4 chirps = unit set for diesel engine 20 sec delay

Press transmitter Lock button to change 2 chirps = transponder output during start only Press transmitter Lock button to change 3 chirps = transponder output until ignition turned off

Press transmitter Lock button to change 2 chirps = temperature start on

Press transmitter Lock button to change 2 chirps = preset crank time w/voltage input check

Press transmitter Lock button to change 2 chirps = shk sensor shunted for the R/S Cycle Press transmitter Lock button to change 3 chirps = shk sensor shunted from tx 1 start cycle

Press transmitter Lock button to change 2 chirps = turbo timer 3 mins Press transmitter Lock button to change 3 chirps = turbo timer 5 mins Press transmitter Lock button to change 4 chirps = turbo timer 10 mins

Press transmitter Lock button to change 2 chirps = aux o/p Black/Blue as alarm feature #1

Note : Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps or the

programming will be terminated.

128-7402

4 of 28

This Remote Start/Alarm System is designed to be used with Automatic Transmission- Fuel Injection Vehicles Only!

for glow plug pre-heat in addition to a "Wait To Start Input" either of which may be required for certain diesel vehicles, (see selectable feature #11 Bank 3 & or Green/Yellow Wire)

glow plug pre-heat system), feature #11 of Bank 3 should remain in the default Gasoline mode setting. For diesel applications, consult your dealer for the type of ignition system used in your particular vehicle. Regardless of the vehicle, Gasoline or Diesel, for every installation, the vehicle MUST HAVE a Tach

Signal Input, Automatic Transmission and Fuel Injection.

The unit provides a selectable ignition control that allows a number of selectable timed outputs

. If the diesel engine has a instant fire, (no

INSTALLATION OF THE MAJOR COMPONENTS:

CONTROL MODULE:

Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting location selected must be within 24" of the ignition switch wiring harness to allow connection of the 6 pin main wiring harness. Be certain that the chosen location will not interfere with proper operation of the vehicle. Avoid mounting the module to or routing the wiring around the steering shaft/column, as the module or wiring may wrap around or block the steering wheel preventing proper control of the vehicle. Secure the module in the chosen location using cable ties or screws as necessary .

Do Not Mount The Module In The Engine Compartment, as it is not waterproof. SIREN:

Select a location in the engine compartment that is not accessible from below the vehicle. The selected location must be clear of hot or moving parts within the engine compartment The siren must be pointed downward to prevent water retention and the flared end must be pointed away from and out of the engine compartment for maximum sound distribution. Before securing the siren, check behind your chosen location to assure that the mounting screws will not penetrate any factory wiring or fluid lines. Secure the siren mounting bracket using #8 self taping screws or by first using the mounting bracket as a template, scribe or mark the mounting holes. Drill the marked holes using a 1/8" drill bit, then mount the siren using #8 sheet metal screws.

HOOD AND TRUNK PIN SWITCHES:

The pin switches included in this package are intended for protecting the hood and trunk areas of the vehicle. In all cases, the switch must be mounted to a grounded metal surface. When the pin switch is activated, (hood/trunk open), it will supply a ground to the input wire activating the alarm. In addition, the hood switch is required for the safety shut down of the remote start unit. If the vehicle is being worked on, this hood switch prevents the remote start activation even if the RF command to start is issued. This

switch must be installed in all applications. Failure to do so may result in personal injury or property damage. Mount the switches in the hood and trunk locations away from water drain paths. If

necessary, the included brackets may be used to move the switch away from rain gutters or allow mounting to the firewall behind the hood seal. In both cases the switch must be set up to allow the hood or trunk door to depress the switch at least 1/4 inch when the hood or trunk is closed and fully extended when the hood or trunk is opened. For direct mounting, a 1/4 inch hole must be drilled. Carefully check behind the chosen location to insure the drill will not penetrate any existing factory wiring or fluid lines. Drill a 1/4" hole in the desired location and thread the pin switch into it using a 7/16" nut driver or deep well socket. If using the mounting bracket, first secure the bracket to the desired location and secure the pin switch in the pre-threaded mounting bracket hole.

128-7402

5 of 28

DASH MOUNTED LED:

The small LED included in the kit will serve as a visual indicator of the alarm's status and provide a visual deterrent to a potential thief. The LED also provides important feed back information during the transmitter and feature program modes. The LED should be installed in the dash in an area highly visible so that it may be seen from the driver's seat as well as from outside the vehicle. Inspect behind the chosen location to insure that the drill will not penetrate any existing factory wiring or fluid lines. Carefully drill a 1/4" hole in the desired location and pass the connector end of the LED through the hole and toward the control module. Press the LED firmly into place until it is fully seated in the mounting hole.

THE RECEIVER/ANTENNA ASSEMBL Y:

The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dash board for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception. Special considerations must be made for windshield glass as some newer vehicles utilize a metallic shielded window glass that will inhibit or restrict RF reception. In these vehicles, route the antenna toward a rear window location for best reception. Secure the antenna with double stick tape provided. After securing the antenna with tape, we advise also securing a section of the antenna cable to a fixed support. This will prevent the antenna from dropping down in case the double stick tape is exposed to extreme heat which may loosen it's gummed surface. Route the connector toward the control module using caution not to pinch the cable as this will cause poor or no RF reception to the control module.

VALET/PROGRAM/MANUAL OVERRIDE SWITCH :

Select a mounting location that is easily accessible to the operator of the vehicle. It is not necessary to conceal the switch. However, concealment is recommended as it offers a higher level of security. The switch can be mounted to the lower dash panel in the driver's area. Inspect behind the chosen location to insure that adequate clearance is allowed for the body of the switch, and also that the drill will not penetrate any existing factory wiring or fluid lines. Drill a 9/32" hole in the desired location and mount the switch by passing it through the panel from the underside. Secure the switch using the nut, star washer. Route the switch's connector toward the control module

NOTE: During the program sequence, there are times when this switch and the ignition switch will be used simultaneously. We recommend that the pushbutton switch be mounted on the left side of the ignition switch to facilitate this operation.

CONTROL SWITCH:

Select a mounting location known and accessible to the operator of the vehicle. A lower dash panel, kick panel, or glove box is desirable. Inspect behind the chosen location to insure that adequate clearance is allowed for the body of the switch, and also that the drill will not penetrate any existing factory wiring or fluid lines. Drill a 1/4" hole in the desired location and mount the switch by passing it through the panel from the underside. Secure the switch using the nut, star washer, and on/of f face plate. It is suggested that the switch be oriented to allow the on position to be up toward the driver and the off position to be down or away from the driver. Route the switch's connector toward the control module.

SHOCK SENSOR:

Select a centrally located, solid mounting surface for the shock sensor that will allow consistent operation from all areas of the vehicle. The selected location must be within 18" of the control module to allow routing and connecting of the 4 pin harness. Secure the shock sensor to the chosen location using two #8 self tapping sheet metal screws. The sensor can also be secured to an existing dash brace using cable tie straps. Whichever mounting method is used be sure to allow access to the sensitivity adjustment potentiometer for use later in the installation.

ST ARTER INHIBIT RELA Y:

Select a mounting location within 12" of the ignition switch's low current start solenoid wire. Secure the relay to an existing harness in the chosen location using a cable tie around the relay's wiring harness. CAUTION! Do not wire tie the metal bracket to an existing wiring harness as vibration may cause chaffing and shorting damaging the factory wiring. If an existing harness is not available then secure the relay's metal mounting tab to an under dash metal brace with a #8 self tapping sheet metal screw. Wire the relay as per the diagram found later in this manual.

128-7402

6 of 28

This unit is to be used in vehicles with AUTOMATIC TRANSMISSIONS only! Although this combination Alarm/Remote Start unit is a sophisticated system with many advanced features, IT MUST NOT be in- stalled into a vehicle with a manually operated transmission. Doing so may result in serious personal injury and property damage. IMPORTANT! It is the responsibility of the installing technician to determine the load factor of the vehicles electrical circuits when the vehicle is running, and to adequately fuse the three power wires based on that load. If the vehicle, running under load with the air conditioner, heater blower motor , and accessories exceed 24 Amps continuous, we recommend that two fuses be used in combination on each power wire as shown below. For additional information see Tech Update issued 9/30/96.

DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MUL TI PIN INPUT / OUTPUT HARNESS INTO THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HA VE BEEN MADE. AFTER SELECTING YOUR T ARGET WIRES AS DEFINED BELOW , DISCONNECT THE NEGATIVE BA TTERY CABLE FROM THE VEHICLE BA TTERY PRIOR TO MAKING ANY CONNECTIONS.

WIRING THE 6 PIN MAIN POWER HARNESS:

RED w/ WHITE Trace Wire: + 12 volts Battery 1 Source

Connect this wire to a + 12 VDC constant source found at the vehicle's ignition switch using the 30 Amp fuse and holder provided. This wire provides power for the control circuit as well as the ignition 1 and ignition 2 relays.

RED Wire: + 12 Volts Battery 2 Source Connect this wire to a separate, (Other than the wire Red or Red/Black is connected to), 12 VDC constant source found at the vehicle's ignition switch using the 30 Amp fuse and holder provided, but NOT the same vehicle wire as used by the battery 1 source. Most vehicles have more than one battery source supplying power to the ignition switch. Separate feed wires must be used for the Red and Red/White wires. If your vehicle does not have two battery feed wires at the ignition switch then it is possible to connect both wires to the vehicle's battery . This wire provides power for the start relay and the accessory relay .

128-7402

7 of 28

IMPORT ANT!

It is the responsibility of the installing technician to determine the load factor of the vehicles electrical circuits when the vehicle is running, and to adequately fuse the two power wires based on that load. If the vehicle, running under load with the air conditioner, heater blower motor , and accessories exceed 24 Amps continuous, we recommend that two fuses be used in combination on each power wire as shown below. For additional information see T ech Update issued 9/30/96.

YELLOW Wire: Starter Output Careful consideration for the connection of this wire must be made to prevent the vehicle from starting while in gear. Understanding the difference between a mechanical and an electrical Neutral Start Switch will allow you to properly identify the circuit and select the correct installation method. In addition you will realize why the connection of the safety wire is required for all mechanical switch configurations.

Failure to make this connection properly can result in personal injury and property damage. In all installations it is the responsibility of the installing technician to test the remote start unit and ensure that the vehicle cannot start via RF control in any gear selection other than park or neutral. In both mechanical and electrical neutral start switch configurations, the connection of the Y ellow wire will be made to the low current start solenoid wire of the ignition switch harness. This wire will have +12 volts when the ignition switch is turned to the start (crank) position only . This wire will have 0 volts in all other ignition switch positions. NOTE: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electrical neutral switch configuration, this connection must be made between the starter inhibit relay , ( when used ) and the neutral safety switch as shown in the following diagram. Failure to connect this wire to the ignition switch side of the of the neutral safety switch can result in personal injury and property damage. SEE NEUTRAL ST ART SAFETY TEST FOR FURTHER DET AILS.

YELLOW START WIRE DETAIL

BLUE Wire: Ignition 1 Output

Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition key is turned to the "ON" or "RUN" and the "START" or CRANK" positions, and will have 0 volts when the key is turned to the "OFF" and "ACCESSORY" positions. For Diesel Applications, this wire must be connected to the ignition circuit that powers the glow plugs if the vehicle requires glow plug pre-heating. (See selectable feature Bank 3 #1 1)

128-7402

8 of 28

GREEN Wire: Ignition 2 Output

Connect this wire to the ignition 2 wire from the ignition switch. This wire will show + 12 volts when the ignition key is turned to the "ON" or "RUN" position and is some cases the "ST ART" or CRANK" position. This wire will show 0 volts when the key is turned to the "OFF" and "ACCESSORY" positions. NOTE: See programming information (Bank 3 Selection #2) concerning this wire to allow output during the "ST ART" mode.

VIOLET Wire: Accessory Output Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignition switch is turned to the "ACCESSORY" or "ON" and "RUN" positions, and will show 0 volts when the key is turned to the "OFF" and "ST AR T" or "CRANK" positions.

WIRING THE 4 PIN AL TERNA TE IGNITION HARNESS ORANGE/BLACK Wire: Parking Brake Input

This wire is used only when the turbo timer mode, Bank 3, feature # 16 is selected ON. This input insures that the vehicle parking brake is applied whenever the vehicle is set up for and the turbo timer circuit is used. This input must switch to ground when the vehicle's parking brake is applied. Connect the Orange/Black wire to the negative output of the vehicle's parking brake switch. RED/BLACK Wire: + 12 Volts Input Note: The Red/Black and Pink are dry contacts and may be used for negative switching when necessary.

Connecting the Red/Black to chassis ground will result in Pink being ground when the R/S is activated.

This input is to be connected to a separate, (Other than the wire Red or Red/White is connected to), constant on + 12 volt source which will supply + 12 volt power to the additional ignition output, (Pink), wire. This should be a separate + 12 volt source other than the 12 volts connected to Red or Red/White PINK Wire: Additional Ignition Output This wire can be used as an additional + 12 Volt ignition output supplied by the Red/Black wire. This output can be selected to be on or off during the start cycle. (See feature bank 3 selection # 8) Connect this wire to the third ignition circuit in the vehicle and set the selectable feature # 8 of Bank 3 according to the way in which the vehicle's ignition switch operates.

128-7402

9 of 28

+ 19 hidden pages