American Standard ACRYLUX 6032Y1.202, ACRYLUX 6032Y1.102 User Manual

ACRYLUX 60" x 32" w/INTEGRAL APRON

❑ 6032Y1.102 Bathing Pool, Right Drain ❑ 6032Y1.202 Bathing Pool, Left Drain

Product Features:

• High-gloss acrylic-capped ABS with berglass reinforcement

• Integral apron

• Integral three-sided, tiling/water retention ange

• Integral lumbar support

• Pre-leveled tub bottom

❑ 6032Y1.118 Whirlpool, Right Drain ❑ 6032Y1.218 Whirlpool, Left Drain

Whirlpool Features:

• 1.25 hp, single-speed pump motor

• 8 whirlpool jets

– 4 adjustable jets – 4 mini-jets in the lumbar and foot areas

• Deck mounted air on/off switch

• Removable access panel

ACRYLUX™ 60" x 32" w/INTEGRAL APRON

WHIRLPOOL AND BATHING POOL

HIGH GLOSS

6032Y1.102

Nominal Dimensions: 59-7/8" x 32" x 18" (1521 x 813 x 457mm)

For use with:

• 6032Y1.BW Bath Wall Set

• 6032Y1.BWT Bath Tile Wall Set

• Tub can also be installed without Acrylux wall set

Compliance Certications Meets or Exceeds the Following Specications:

• UL 1795 for Hydromassage Bathtubs

• ASME A112.19.7M for Whirlpool Appliances

• ANSI Z124.1 for Plastic Bathtubs

• ASTM E162 for Flammability

• NFPA 258 for Smoke Density

6032Y1.118

H129

Revised 5/08

ACRYLUX™ 60" x 32" w/INTEGRAL APRON

GENERAL SPECI FICATIO NS FOR 6032Y1 WHIRLP OOL

60 x 32 x 18 In . (15 24 x 81 3 x 4 57 mm )

76 Lbs. (3 4 Kg. )

526 Lbs. ( 23 9 K g.)

54 Gal. (2 04 L) 28 Gal. (1 06 L)

3 I n. L (7 6m m L )

54 In. L ( 13 72m m L)

14 in (3 56 mm L)

39 Lbs. /S q. Ft. (193 K gs ./S q.m)

7.3

23. 321ft

1.2 5 HP, 9 .7 AM PS ,1 20 V.WHI RLPOO L PU MP

WHIRLPO OL ELE CTRICAL SPECI FICATIO NS

INS TALLE D SI ZE WEI GHT WEI GHT w /W AT ER GAL . TO OV ER FLO W WHI RLPOO L MI N. OPERA TI NG VO L. BAT HING WE LL AT SUMP BAT HING WE LL AT RIM WAT ER DE PT H TO OVERF LO W FLO OR LO AD IN G (PR OJECT ED A REA ) PTS .

CUB E (F T3)

GENERAL SPECI FICATI ONS FOR 6032Y 1 BATH ING POO L

60 x 32 x 1 8 I n. (1 52 4 x 813 x 4 57 mm )

54 Lb s. ( 24 Kg .)

495 L bs . (2 25 Kg.)

53 Ga l. ( 20 1 L )

3 I n. L ( 76 mm L)

54 In . L (1 372 mm L)

14 in ( 35 6m m L )

37 L bs ./ Sq .Ft . (18 1 Kg s. /Sq.m )

7.3

23. 32 1f t

INS TA LL ED S IZE WEI GH T WEI GH T w/ WA TER GAL . TO O VE RFL OW BAT HI NG W EL L A T SUM P BAT HI NG W EL L A T RIM WAT ER D EP TH TO OVER FL OW FLO OR L OA DI NG (PR OJ EC TE D ARE A) PTS .

CUBE (FT3)

10"

STUD LAYOUT

33-1/2"

(851mm)

60"

(800mm)

(254mm)

10"

6" (154mm)

15" (381mm)

(203mm)

Drain C

Floor Cut Out 6" x 10" (154 x 254mm)

= Stud Location

59-7/8"

(1521mm)

18"

(457mm)

32"

(813mm)

WHIRLPOOL AND BATHING POOL

HIGH GLOSS

NOTES:

BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR PENINSULA T YPE INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIALS BY OTHERS.

■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.

● FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.

● IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING

SYSTEM PIPING AND DRAIN OVERFLOW. MOUNTING HOLES DRILLED BY INSTALLER.

IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaet.

H130

Revised 5/08