American Standard A112.19.4M User Manual

CHANDLER™ AMERICAST® ISLAND SINK

• Americast® brand engineered material

• Single bowl design

• Titanium enamel - heat resistant up to 1000°

• Acid-resisting glossy porcelain nish

• Top mount or undercounter installation

• Silicone sealant supplied

• Available CHO, 3 faucet hole conguration, or less ttings deck

• Customized hole punchings available (see page G57)

Top Mount/Undercounter:

❏ 7182.001 Center hole only ❏ 7182.803 3 hole ❏ 7182.000 No faucet holes

Undercounter Installation Order:

❏ 791003-100 Mounting Kit (consists of

cut-out templates and mounting hardware)

Nominal Dimensions with faucet hole

7182.001 and 7182.803:

419 x 381 x 216mm (16-1/2" x 15" x 8-1/2")

CHANDLER™

ISLAND SINK

7182.001/7182.803

AMERICAST

Nominal Dimensions no faucet hole 7182.000:

419 x 314 x 216mm (16-1/2" x 12-3/8" x 8-1/2")

Bowl sizes for all models:

330mm (13") wide 229mm (9") front to back 203mm (8") deep

Compliance Certications Meets or Exceeds the Following Specications:

• ASME A112.19.4M for Americast Plumbing Fixtures

• ASTM E162 for Flammability

• NFPA 258 for Smoke Density

7182.000

SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS

To Be Specied:

❏ Color: ❏ Faucet*: ❏ Faucet Finish: ❏ Basket Strainer: 4331.013 ❏ Soap Dispenser: 4503.115, Color: ❏ Trap:

Optional Accessories:

❏ Small Wood Cutting Board: 9000.185 ❏ Colander For Cutting Board: 8102.100, Color:

* See faucet section for available models

G47

Revised 2/08

COUNT ERTOP

(BY O THERS )

SEALI NG COMPO UND

FINIS HED

FLOOR

C/L

7182. 001

(1 HO LE)

*CUT OUT

NO TE

HOT

COLD

2" (5 1mm)

OPTIO NAL

FINIS HED W ALL OR SP LASHB ACK

(3) 3 8mm ( 1-1/2)

DIA. HOLES TYP.

1-1/ 2" O.D. TAIL PIECE

36" ( 914mm)

SUGG ESTED

5-3/ 4" (146 mm)

(203 mm)

16-1 /2"

(419 mm)

1/2"

(13m m)

8-1/ 4"

(210 mm)

3-1/ 2"

(89m m)

DIA.

1" (2 5mm) RAD. TYP.

3/4" (19m m)

15"

(381 mm)

8-13 /16" (229 mm)

2" (51m m)

(51m m)

CHANDLER™

DETAI L OF M OUNTI NG CLI P

(KIT No.791 003-1 00)

BRASS

INSER T

1/2

(13mm )

MIN.

REFER TO IN STRUCT IONS

PROVI DED WI TH KIT FOR

ADDIT IONAL INFORM ATION

CLIP MACH. SCREW

SINK

C/L

MOUNT ING C LIP

(SEE DETAI L)

7182. 001

(1 HO LE)

*CUT OUT

NO TE

HOT

COLD

FINIS HED W ALL OR SP LASHB ACK

COUNT ERTOP

(BY O THERS )

SEALI NG COMPO UND

FINIS HED

FLOOR

2" (5 1mm)

OPTIO NAL

(3) 3 8mm ( 1-1/2) DIA. HOLES TYP.

1-1/ 2" O.D. TAIL PIECE

36" ( 914mm)

SUGG ESTED

5-3/ 4" (146 mm)

16-1 /2"

(419 mm)

8-1/ 4"

(210 mm)

3-1/ 2"

(89m m)

DIA.

1" (2 5mm) RAD. TYP.

3/4" (19m m)

15"

(381 mm)

8-13 /16" (229 mm)

2" (51m m)

(51m m)

8-1/ 2"

(216 mm)

C/L

*CUT OUT

NO TE

HOT

COLD

FINIS HED W ALL OR SP LASHB ACK

COUNT ERTOP

(BY O THERS )

SEALI NG COMPO UND

FINIS HED

FLOOR

2" (5 1mm)

OPTIO NAL

1-1/ 2" O.D. TAIL PIECE

36" ( 914mm)

SUGG ESTED

5-3/ 4" (146 mm)

(203 mm)

16-1 /2"

(419 mm)

12-3 /8"

(314 mm)

6-3/ 16"

(157 mm)

1/2"

(13m m)

8-1/ 4"

(210 mm)

3-1/ 2"

(89m m)

DIA.

(3) 1-1/8" (29mm )

DIA. HOLES TYP.

1" (2 5mm) RAD. TYP.

3/4" (19m m)

(51m m)

DETAI L OF M OUNTI NG CLI P

(KIT No.791 003-1 00)

BRASS

INSER T

REFER TO IN STRUCT IONS PROVI DED WI TH KIT FOR

ADDIT IONAL INFORM ATION

CLIP MACH. SCREW

SINK

C/L

MOUNT ING C LIP

(SEE DETAI L)

*CUT OUT

NO TE

HOT

COLD

FINIS HED W ALL OR SP LASHB ACK

COUNT ERTOP

(BY O THERS )

SEALI NG COMPO UND

FINIS HED

FLOOR

2" (5 1mm)

OPTIO NAL

1-1/ 2" O.D. TAIL PIECE

36" ( 914mm)

SUGG ESTED

5-3/ 4" (146 mm)

16-1 /2"

(419 mm)

12-3 /8"

(314 mm)

6-3/ 16"

(157 mm)

3-1/ 2"

(89m m)

DIA.

(3) 1-1/8" (29mm )

DIA. HOLES TYP.

1" (2 5mm) RAD. TYP.

3/4" (19m m)

(51m m)

1/2

(13mm )

MIN.

8-1/ 2"

(216 mm)

2" (51m m)

ISLAND SINK

7182.001/803 Top Mount 7182.001/803 Undercounter Mount

AMERICAST

NOTES:

FOR COUNTERTOP CUTOUT AND INSTALLATION INSTRUCTIONS

USE TEMPLATE SUPPLIED WITH SINK .

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND COUNTERTOP SUPPORTS.

NOTES:

TEMPLATE PROVIDED WITH MOUNTING KIT 791003-100 FOR

UNDERCOUNTER, INSTALLATION AND COUNTERTOP CUTOUT.

FITTINGS AND UNDERCOUNTER MOUNTING KIT NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND COUNTERTOP SUPPORTS.

7182.000 Top Mount 7182.000 Undercounter Mount

NOTES:

TEMPLATE PROVIDED WITH MOUNTING KIT 791003-100 FOR

UNDERCOUNTER, INSTALLATION AND COUNTERTOP CUTOUT.

FITTINGS AND UNDERCOUNTER MOUNTING KIT NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND COUNTERTOP SUPPORTS.

G48

NOTES:

FOR COUNTERTOP CUTOUT AND INSTALLATION INSTRUCTIONS

USE TEMPLATE SUPPLIED WITH SINK .

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND COUNTERTOP SUPPORTS.

IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ASME Standard A112.19.4 These measurements are subject to c hange or cancellation. No responsibility is assumed for use of superseded or voided leaet.

Revised 2/08