American Standard A112.19.9M, 9960.403, 9960.803, 9960.001 User Manual
MEZZO™ SEMI - COUNTERTOP SINK
19"
(482mm)
1-3/8" (35mm) Dia.
1 Hole for CHO
9960 001
1-3/8" (35mm) Dia. 3 Holes
for 8" (203mm) centres
9960 803
1-1/4" (32mm) Dia. 3 Holes
for 4" (102mm) centres
9960 403
2-3/4"
(70mm)
8"
(203mm)
22"
(559mm)
4"
(102mm)
8"
(203mm)
15"
(381mm)
21-1/2"
(546mm)
Countertop
10-1/2"
(267mm)
11"
(279mm)
13" min.
(330mm)
10-1/2"
(267mm)
2-1/2"
(64mm)
10-1/2"
(267mm)
(cut out size)
Countertop
By Others
Finished
Floor
Finished
Wall
8-1/4"
(210mm)
6"
(152mm)
34"
(864mm)
IN ONTARIO
33"
(838mm)
1-3/8"
(35mm)
4-3/8"
(111mm)
*
10-5/8"
(270mm)
*
12-7/8"
(327mm)
1-1/4 O.D.
WASTE
SUPPLY
SCREW
NUT
FLAT
WASHER
#10 SCREW
MOUNTING BRACKET
COUNTERTOP -
BY OTHERS
WATERPROOF
SEALANT
BASIN
• Space saving design installs on a minimum
countertop depth of 13"
• Made from reclay china
• Rear overow
• Recessed self-draining deck
• Barrier-free design
• Self rimming with sealant
• Cutout template and mounting kit provided
(Faucet shown not included)
❏ 9960.803 Faucet holes on 8" (203mm) centers
(illustrated)
❏ 9960.403 Faucet holes on 4" (102mm) centers
❏ 9960.001 Center hole only
Nominal Dimensions:
22" (559mm) wide, 21-1/2" (546mm) deep
Bowl sizes:
19" (482mm) wide
15" (381mm) front to back
6-7/8" (175mm) deep
Fixture Dimensions conform to ANSI Standard
A112.19.9M
Compliance Certications Meets or Exceeds the Following Specications:
• ASME A112.19.9M for Non-Vitreous
• CAN/CSA B45 series
• A1995 National Building Code, section 3.7 and
CAN/CSA-B651-02 and OBC 3.8
Ceramic Fixtures
MEZZO™
SEMI-COUNTERTOP SINK
FIRECLAY
To Be Specied:
❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Black
❏ Faucet*:
❏ Faucet Finish:
❏ Supplies & Stops:
❏ Trap 1-1/4" (32 mm):
* See faucet section for additional models available
NOTES:
*
ARE SUGGESTED.
FOR COUNTERTOP CUTOUT AND INSTALLATION INSTRUCTIONS
USE TEMPLATE SUPPLIED WITH SINK .
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ANSI Standard A112.19.9M.
These measurements are subject to change or cancellation.
No responsibility is assumed for use of superseded or voided pages.
© 2008 AS America Inc.
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TR AP
J28
Revised 2/08
Loading...