American Standard 9532.200 User Manual

™

ASSEMBLY & INSTALLATION
INSTRUCTIONS

Bordeaux 32" Vanity with Wood Top

9532.200

VANITY TOP RECOMMENDED SINKS

WOOD TOP (SUPPLIED) SEBRING 0573

MARBLE TOP (OPTIONAL)

9532.495

Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years.
To help insure that the installation process will proceed smoothly, please read these instructions carefully before you
begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.

To maintain the beauty of the finish, avoid placing the furniture in direct sunlight, as sunlight causes fading. Also avoid
extreme changes in temperature by arranging furniture away from radiators, heat and air vents, and air conditioning units.
Avoid placing furniture directly under windows.

COVENTRY 0575
OVALYN 0495.221

Recommended Tools & Materials

Adjustable Wrench

Basin Wrench

Tubing Cutter

Channel Locks

Plumbers' Putty or
Caulking

Roughing-in Dimensions

32-3/8"

WASTE

822mm

6"

(152mm)

ANCHORING HOLES

6"

(152mm)4"TYP

1-1/4" O.D.

32-3/4"
832mm

A

SUPPLIES
AS REQ'D

Hacksaw

Saber Saw

22-3/4"

578mm

Pipe Wrench

10'

Tape
Measure

Putty Knife

A = 35-5/8"(981mm) for Wood top
A = 35-3/4"(908mm) for Marble top

24-3/4"

629mm

DOORS SWING approx 150°
DEPTH WITH DOORS

1/2 OPEN = 32"
WIDTH WITH BOTH DOORS

FULL OPEN= 47-1/2"

Drill

Phillips Screwdriver

Regular Screwdriver

Level

21-1/4"

540mm

FINISHED FLOOR

Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2002

730548-100 Rev. B

- 1 -

VANITY INSTALLATION

Provide suitable reinforcement required for anchoring the vanity to the wall. Centerline of reinforcement should be 32­3/4" up from the floor (see Figure 1).

The molding needs to be notched to seat the vanity flush against the wall (see Figure 2).
Rough in supply lines and waste per rough in dimensions.
NOTE: If current supply lines are greater than 6" on center, they may interfere with cutout in rear of vanity or vanity shelf.
Remove the wood top from the vanity. The top is held in place from the underside by 4 screws, 1 through each of the 4

angled corner braces.
Move the vanity into place and anchor it to the wall through at least 2 of the anchoring holes in the rear of the vanity (see

Figure 2).
Continue with installation appropriate for top and sink options chosen.

21-1/4"

540mm

C/L of 2 x 6
Reinforcement

ANCHORING

HOLES

FIGURE 1

32-3/4"

FIGURE 2

32-3/4"

832mm

Finished
Floor

Wood Top with Recommended Sinks...

Two people recommended for this installation

Determine which sink is being installed and follow the instructions printed on the
appropriate template supplied with vanity.

NOTE: American Standard is not responsible for cut-out errors when the
incorrect cut-out template is used.

If Installing: Use Template:

Sebring 0573 730541-400
Coventry 0575 730542-400

After top is replaced, connect the trap to the drain assembly hand tight to check
alignment. It may be necessary to cut off part of the tailpiece (area "A") or part
horizontal leg of the trap (area "B").

Connect hot and cold supply lines to the shut off valves. Tighten trap joints for
watertight assembly.

WOOD V ANITY T OP

IMPORTANT: BE SURE TO CENTER SINK
CUT OUT HORIZONTALLY ON VANITY TOP.

MOLDING

P APER TEMPLATE

B

A

- 2 -

730548-100 Rev. B