American Standard 9440.000 User Manual

“”

THE

COLLECTION

™

ASSEMBLY & INSTALLATION INSTRUCTIONS

WASHSTAND

9440.000

Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years. To help insure that the installation process will proceed smoothly, please read these instructions carefully before you begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.

Recommended Tools & Materials

Adjustable Wrench

Channel Locks

Plumbers' Putty or Caulking

Level

0283.008 STANDARD WASHSTAND TOP

9441.000 WASHSTAND TABLE LEGS

10-1/4

(260mm)

1-3/4" DIA.

STD. DRAIN

OUTLET

(330mm)

(203mm)

3/4

(19mm)

3-7/8

(98mm)

(508mm)

Phillips Screwdriver

Regular Screwdriver

Tape Measure

Putty Knife

Pipe Wrench

Hacksaw

Drill

Product names listed herein are trademarks of American Standard Inc. © American Standard Inc. 2003

FINISHED WALL

17-15/16 (456mm)

- 1 -

8-1/2

(216mm)

(914mm)

FINISHED

FLOOR

SUPPLIES AS

REQUIRED

1-1/4 O.D.

WASTE

26-3/4

(680mm)

(203mm)

22-5/8

(575mm)

(559mm)

7-1/2

(191mm)

28-1/2

(724mm)

(610mm)

730805-100

WASHSTAND ASSEMBLY

Thread the two legs with tapered upper ends into the threaded holes at the front of the cabinet. Thread the remaining legs into the two holes at the rear of the cabinet. Hand-tighten each of the four legs.

Thread knobs onto drawer with screws provided.

Back

Front

SINK AND WASHSTAND INSTALLATION

Note: If replacing an existing sink be certain to shut off water supply before removing old sink. If installing in a new bathroom follow rough-in diagram to locate rough supply, waste lines.

Provide suitable reinforcement behind finished wall for sink hanger screws. For an installed sink height of 36", center the reinforcement 30-3/4" above the floor.

1) Move washstand into approximate position near the wall.

2) Place sink on washstand, aligning the tapered ends of the front legs with the recesses in the underside of the front of the sink.

3) Place a level on the cabinet and use the four independently adjustable washstand feet to level the assembly both side-to-side and front-to-back.

4) Place the level on the sink. If adjustment is required, either front-to-back or side-to-side, remove the sink, place one or more of the adhesive-backed cushions on the top surfaces of any of the legs as appropriate, and replace the sink to verify.

5) Move the assembly into contact with the wall.

6) With a pencil, mark through the center of the two mounting holes found on the back of the sink. See VIEW "A".

7) Move the assembly well clear of the wall.

8) Drill two pilot holes at the center marks using a 1/4" bit. Bore in 1" deep.

9) Thread the two 5/16" headless hanger screws into the pilot holes leaving

1-7/8" thread exposed in front of the wall.

C/L of 2 x 8 Support and Bracket

Finished Floor

30-3/4 "

VIEW "A"

With lavatory in place mark the

two mounting hole locations.

Feet are adjustable

Following manufacturer's instructions, install faucet and drain assembly (not included) in sink. Be certain to apply a bead of sealing putty on the underside of the drain to ensure a watertight seal between the sink and the drain. Remove excess putty immediately after tightening drain.

Move the assembly back toward the wall, guiding the sink over the two headless hanger screws. Place washers over studs and firmly hand-tighten nuts onto each.

- 2 -

Lavatory

Front Leg of Washstand

Hanger Screw, Washer & Nut

730805-100

+ 1 hidden pages