American Standard 9378.335.XXX, 9374.335.XXX, 9371.335.XXX User Manual
ASSEMBLY & INSTALLATION
INSTRUCTIONS
TOWN SQUARE CLASSIC CADDIE
9378.335.XXX
9374.335.XXX
9371.335.XXX
Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years.
To help insure that the installation process will proceed smoothly, please read these instructions carefully before you
begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.
Recommended Tools & Materials
Adjustable Wrench
0790.XXX TOWN SQUARE PEDESTAL SINK
9370.100.335 CLASSIC CADDIE
FINISHED
WALL
9-1/2"
(241mm)
4"
(102mm)
18-3/4" (476mm)
2-5/8"
(67mm)
Channel Locks
Plumbers' Putty or
Caulking
Tape
Measure
Regular Screwdriver
Pipe Wrench
Level
Phillips Screwdriver
1-3/4" DIA.
STD. DRAIN
OUTLET
(508mm)
★ 20"
★ 18"
(457mm)
24"
(610mm)
6"
(152mm)
SUPPLIES AS
REQUIRED
1-1/4" O.D.
WASTE
1-1/4" O.D.
TAILPIECE
20-1/4"
(514mm)
■
(95mm)
8"
(203mm)
28"
(711mm)
3-3/4"
36"
(914mm)
Putty Knife
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2004
Drill
16-1/8"
(410mm)
- 1 -
14-1/8"
(359mm)
FINISHED
FLOOR
730833-100
1
SINK AND CADDIE INSTALLATION
Note: If replacing an existing sink, shut off the water
supply before removing old sink. If installing in a new
bathroom, follow the rough-in diagram to locate the
rough supply and waste lines.
Provide suitable reinforcement behind finished wall for
sink hanger screws. For an installed sink height of
36", center the reinforcement 32" above the floor.
2
1) Move the caddie into approximate position near the wall.
2) Place the sink on the caddie.
3) Place the level on the sink. If adjustment is required, either front-to-back
or side-to-side, remove the sink, place one or more of the adhesivebacked cushions on the top surfaces of the caddie, and replace the sink
to verify.
4) Move the assembly into contact with the wall.
5) With a pencil, mark through the center of the two mounting holes found
on the back of the sink. See VIEW "A".
6) Move the assembly away from the wall.
7) Drill two pilot holes at the center marks using a 1/4" bit. Bore in 1" deep.
8) Thread the two 5/16" headless hanger screws into the pilot holes leaving
1-7/8" thread exposed in front of the wall.
C/L of 2 x 8
Support
and Bracket
32"
Finished
Floor
VIEW "A"
With sink
in place mark
the two
mounting
hole locations.
3
Following the manufacturer's instructions, install faucet and
drain assembly (not included) in the sink. Apply a bead of
sealing putty on the underside of the drain to ensure a
watertight seal between the sink and the drain. Remove
excess putty immediately after tightening drain.
Move the assembly back toward the wall, guiding the sink
over the two headless hanger screws. Place washers over
studs and firmly hand-tighten nuts onto each.
4
Connect the trap to drain assembly hand tight to check alignment. It may be
necessary to cut off part of the tailpiece (area "B") or part of the horizontal leg
of the trap (area "C").
Connect hot and cold supply lines between the fitting valve and the supply
shut-off valves. Tighten trap joints for watertight assembly. Apply a bead of
caulk around the back edge of the sink where it contacts the wall.
Tighten the sink securely against the wall.
Sink
Hanger Screw,
Washer & Nut
C
B
- 2 -
730833-100
Loading...