American Standard 9118.111, 9118.15, 9118.1, ICU Sink System User Manual
INSTALLATION INSTRUCTIONS
ICU Sink System
Models: 9118.111, 9118.100 & 9118.150
Introduction: Thank you for selecting our products...products which have been the
benchmarks of fine quality for years. To help insure that the installation process will
proceed smoothly, please read these instructions carefully before you begin. Also,
review the recommended tools and materials list; carefully unpack and examine your
new plumbing fixture.
!
CAUTION: PRODUCT IS FRAGILE. TO AVOID DAMAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
Recommended Tools & Materials
Tape
Measure
Adjustable Wrench
Plumbers' Putty or Caulking
Torch
Pipe Wrench
Tubing Cutter
Level
Channel Lock Pliers
Rough-In
Dimensions
14-3/4"
(375mm)
26-1/8"
(663mm)
*DISCLAIMER: Faucets with a base diameter greater than 2-1/4" (57 mm) will not fit on this
ICU Sink. The Selectronic ICU Faucet was specifically designed to minimize splashing during
operation. American Standard will not be liable for any splashing that occurs if faucets other
than the American Standard ICU Faucets are used.
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2012
4-3/4"
(121mm)
17"
(432mm)
(14mm)
*FAUCET PERCH
2-1/2" DIA. (65mm)
40-1/8"
(1020mm)
36-1/2"
(927mm)
5/8"
36"
(914mm)
Drill
(509mm)
4-3/4"
(120mm)
FINISHED
FLOOR
20"
8"(203mm) BETWEEN
MOUNTING HOLES
BASE MOUNT
Phillips Screwdriver
*FAUCET PERCH
2-1/2" DIA. (65mm)
1/2" DIA.
(13mm)
9/16" DIA.
(14mm)
2-3/4"
(70mm)
DETAIL
(102mm)
36-1/2"
(927mm)
2-3/4"
(70mm)
4"
4"
(102mm)
Regular Screwdriver
FINISHED WALL
MOUNTING
STUDS
1-5/8"
(41mm)
FINISHED
FLOOR
Hacksaw
Pencil
8" (203mm)
FINISHED
FLOOR
RECOMMENDED CARRIERS:
JAY R. SMITH MFG. CO.
MODEL SQ-0-4437
FLOOR MOUNTED SINK SUPPORT
WATTS CA-311
FLOOR MOUNTED URINAL CARRIER
SAVE FOR FUTURE USE
1
7301793-100 Rev. D
1
1. Rough-in 3/8" supplies and waste outlet connections.
NOTE: For ease of installation and accessibility, it is
recommended that straight stops with flex supply tubes be
used. As an alternative, if rigid supply risers are used, it is
suggested to use angle stops in place of the straight stops.
SQ-0-4437 FLOOR
MOUNTED SINK
SUPPORT
4"
8" (203mm)
3/8" (10mm)
SUPPLIES
*1-1/4" (32mm)
OR 1-1/2" (38mm)
WASTE OUTLET
FINISHED
FLOOR
FINISHED WALL
MOUNTING
STUDS
1-5/8"
(41mm)
36-1/2"
(927mm)
(457mm)
(102mm)
18"
INSTALL FAUCETROUGH-IN SUPPLIES AND WASTE OUTLET
2
NOTE: For more detailed information, see the installation
instructions supplied with the ICU FAUCET. #(M965119)
1. Insert WIRES (1), FLEX HOSE (2) and SPOUT SHANK (3)
through center hole of mounting surface.
2. Assemble "C" WASHER (4), STAR WASHER (5) and LOCKNUT
(6) onto threads of SPOUT SHANK (3) from underside of mounting
surface.
3. Align FAUCET and tighten LOCKNUT (6).
4
5
6
2
3
1
4
3
5
6
*CHECK LOCAL CODES
3
INSTALL GRID DRAIN AND OFFSET TAILPIECE
1. Apply plumber’s putty to the underside of flange. Install GRID DRAIN into drain outlet.
2. From the underside of SINK install RUBBER GASKET (flat side up) and FRICTION
GASKET onto GRID DRAIN threads. Apply sealent to threads of GRID DRAIN.
3. Apply sealent to threads of OFFSET TAILPIECE and thread into DRAIN ELL.
4. Thread DRAIN ELL onto GRID DRAIN, tighten and align as shown.
1 2
GRID DRAIN
PLUMBER’S
PUTTY
FRICTION
GASKET
GRID DRAIN
DRAIN ELL
4
3
DRAIN ELL
APPLY
SEALANT
7301793-100 Rev. D
RUBBER
GASKET
APPLY SEALANT
TO THREADS
2
OFFSET TAILPIECE
INSTALL ICU SINK
4
1. Mount SINK onto the two HANGER STUDS. Hold SINK in place
and temporarily install NYLOCK NUT & WASHER on one of the
HANGER STUDS to retain SINK.
HANGER STUD
NYLOCK NUT
AND WASHER
INSTALL ELECTRONICS HANGER BRACKET
5
1. Install the ELECTRONICS HANGER BRACKET onto remaining
HANGER STUD. Install NYLOCK NUT & WASHER but do not
tighten fully.
2. Remove NYLOCK NUT & WASHER from first HANGER STUD
and install other end of ELECTRONICS HANGER BRACKET.
Replace NYLOCK NUT & WASHER, tighten both ends. Do not over
tighten, chinaware could become damaged.
ELECTRONICS
HANGER BRACKET
6
COMPLETE WASTE OUTLET CONNECTION
1. Install “P” TRAP. Connect OFFSET TAILPIECE to “P” TRAP.
TAILPIECE may have to be cut to fit installation. Use tubing cutter to
cut TAILPIECE.
TAILPIECE
1-1/4" OD
1-1/4" or 1-1/2" OD
WASTE OUTLET
P-TRAP
CONNECT SPOUT HOSE TO ENCLOSURE
8
1. Connect SUPPLY NUT (1) from SPOUT assembly to nipple on
top of ENCLOSURE (2). Tighten with adjustable wrench to make a
water tight connection.
MOUNT ELECTRONICS BOX
7
NOTE: Installation with ELECTRONIC BOX only is for cold
or tempered water. Use optional MIXING VALVE with
ELECTRONIC BOX when Hot and Cold supplies are
roughed-in. See illustration below.
ELECTRONIC BOX
COLD WATER OR
TEMPERED WATER
(3/8" SUPPLY)
1. Remove COVER from ELECTRONICS BOX.
2. Place ELECTRONICS BOX onto MOUNTING PLATE. Align
BOX with mounting holes. Attach with SCREWS provided.
3. Hang MOUNTING PLATE with ELECTRICAL BOX on
HANGER BRACKET.
HOT
ELECTRONIC
BOX
ELECTRONIC
BOX
MIXING VALVE
COLD
SCREWS
1
2
3
MOUNTING PLATE
MIXING VALVE
7301793-100 Rev. D
Loading...