American Standard 9035.374, 9038.374 Installation Manual
Tubing Cutter
INSTALLATION
INSTRUCTIONS
9035.374
SPECTRA+ TOUCH
™
9038.374
Shower Head For all Models
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work is begun.
Channel Locks
Adjustable Wrench Teon Tape
CARE AND CLEANING
Do: Simply rinse the product clean with clear water, dry with a soft cotton flannel cloth.
Do Not: Clean the product with soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.
Certied to comply with ANSI A112.18.1M
Plumbers' Grease
1
INSTALL SHOWER HEAD
SHOWER ARM WITH FLANGE
• Apply sealant or Teon tape to threads on SHOWER ARM (1).
• Thread SHOWER HEAD (3) onto the SHOWER ARM (1).
1a
INSTALL REMOTE (OPTIONAL)
• Identify desired remote location and wipe mounting surface
clean before installing the remote. Use the Yellow tag to
separate REMOTE BASE (1) from REMOTE FACE (4).
To install the remote follow either Option 1 or Option 2.
Option 1
• Peel the lm off of the double sided tape and install REMOTE
BASE (1) to the desired location. Once the REMOTE BASE (1)
is properly seated, install REMOTE FACE (4) by placing over
the REMOTE BASE (1) and gently pushing it forward.
Option 2
• Place REMOTE BASE (1) in the desired location and drill holes
using the HOLES (3) on the REMOTE BASE (1) as templates
and install SCREWS (2) (Make sure to not ruin the nish). Install
REMOTE FACE (4) by placing over the REMOTE BASE (1) and
gently pushing it forward.
CAUTION
Protect finish on SHOWER HEAD
and TUB SPOUT when installing.
1
4
2
3
3
1
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
- 1 -
M965815 (8/17)
2
INSTALLATION TEST
• Turn water supplies on and check for leaks.
• Using your nger touch the Rim (Grey shaded area) (1)
to switch between different modes.
2a
REMOTE FUNCTIONALITY TEST (OPTIONAL)
• Press on Button (1) to switch between different modes.
3
SERVICE
• Clean the Nozzles on the shower head by massaging each nozzle
using your nger.
• Clogged nozzles can also be cleaned using toothbrush. Dip the
toothbrush in vinegar and gently rub the nozzles with dipped
toothbrush. Turn the shower on and let the water run for some
time to clear the vinegar out.
BATTERY NEEDS REPLACEMENT:
For Shower Head
• When battery is low, the shower head will switch to the drench
function and touch and/or remote function will stop working.
• Push Button (1) forward and pull the tray out. Replace the batteries
and place the tray back in. (Note: Make sure to push the tray in until
you hear a click.)
• Replace batteries in battery holder with Qty (3) AA alkaline type
batteries.
• Always change all 3 batteries. Failure to replacing all 3 batteries at
the same time may cause electronics to not work properly.
• Battery lifetime is approximately 5 year under normal use.
1
1
For Remote
Note: Shower Head is not restricted to a specific remote.
• If the touch function on the shower head is still working, then that is
the indication that the battery for the remote needs to be changed.
• Replace batteries in battery holder with Qty (1) 3v Lithium cell.
• Pull Remote Face (1) to separate the Remote Base (3) from
Remote Face (1). Unthread Cover (2) by turning counter
clockwise. Push Spring (5) back to release the battery.
Once the battery is replaced, Thread Cover (2) by turning it
clock wise. Install Remote Face (1) back onto Remote Base (3),
making sure that knob (4) aligns with the Remote Base (3) .
• Battery lifetime is approximately 5 year under normal use.
- 2 -
4
3
1
5
2
M965815 (8/17)
Loading...