American Standard 8335.018, 8335.024, 8335.190, 8335.210, 8335.230 Installation Manual
Installation
Instructions
CS SERIES
Contemporay Square Accessories
18" TOWEL BAR
24" TOWEL BAR
TOWEL RING
DOUBLE ROBE HOOK
TOILET PAPER HOLDER
8335.018
8335.024
8335.190
8335.210
8335.230
Thank you for selecting American-Standard...the benchmark
To ensure that your installation proceeds smoothly--please
read instructions carefully before you begin.
Recommended Tools
10'
Electric Drill
Tape Measure
Level
Regular Screwdriver
Phillips Screwdriver
4mm Hex wrench
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR
WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.
M965368 REV. 1.1
INSTALLATION OF MOUNTING BRACKETS
1
FOR ALL WALL MOUNTED ACCESSORIES
The WALL MOUNTED ACCESSORIES work best if secured to a wall stud or cross brace within the wall, using the SCREWS (2) supplied.
If the ACCEASAORY is to be installed on a tile or plaster wall the ANCHORS (3) and SCREWS (2) should be used.
Determine desired height and location (optional) and mark a center line. Make sure the centerline is level. Using the MOUNTING
BRACKET (1) as a template mark the two spots for the mounting holes. If MOUNTING BRACKET (1) is secured to a stud or cross
brace drill small pilot holes for SCREWS (2).
For installations on tiled walls or drywall, use TILE ANCHORS (3) and SCREWS (2) for securing MOUNTING BRACKET (1) to wall. Drill two
1/4" diameter holes a minimum of 1-1/4" deep. Insert the two TILE ANCHORS (3) flush with face of finished wall. Place MOUNTING
BRACKET (1) over TILE ANCHORS (3) and insert SCREWS (2) provided with a flat blade screwdriver. See illustration below.
Secure MOUNTING BRACKET (1) to wall with SCREWS (2)
LEVEL
DRILL PILOT HOLE FOR
WOOD SCREW (2) OR
1/4" DIA. HOLE FOR
3
1
2
OPTIONAL TO
FINISHED FLOOR
ANCHOR (3)
1
2
C
L
3/4" (19mm)
3/8" (9mm)
OPTIONAL TO
FINISHED FLOOR
3
TOWEL RING and ROBE HOOK INSTALLATION
2
Refer to Step 1 for installation of MOUNTING BRACKETS (2). Align accessory and place ACCESSORY ESCUTCHEON (1) onto
MOUNTING BRACKET (2) Secure accessory with SET SCREW (3) using a 4mm HEX WRENCH (4).
1
FINISHED WALL
2
2
1
3
4
OPTIONAL TO
FINISHED FLOOR
3
4
INSTALL TOILET PAPER HOLDER
3
Refer to Step 1 for installation of MOUNTING BRACKETS (1). NOTE: The center line distance between the two
MOUNTING BRACKETS is 6-1/2" (166mm). Make sure the two MOUNTING BRACKETS (1) are level.
Install the ACCESSORY ESCUTCHEONS (2) on the MOUNTING BRACKETS (1). Make sure the ACCESSORY ESCUTCHEONS (2) with
holes for the horizontal shaft are facing inward. Secure ACCESSORY ESCUTCHEONS (2) with SET SCREW (3) using a 4mm HEX WRENCH (4).
Install the PAPER HOLDER SHAFT (5) into the mounted ACCESSORY ESCUTCHEONS (2).
FINISHED WALL
6" (153mm)
C
L
2
2
3
3
4
4
3
1
LEVEL
2
OPTIONAL TO
FINISHED FLOOR
1
4
3
5
5
4
M965368 REV. 1.1
Loading...